d/freebsd-skq
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
5b9926665b
freebsd-skq/sys/dev/aic7xxx/aic7xxx_freebsd.c
gibbs cb6621f7e0 ahc_pci.c: 
If bus_dma will give us addresses > 32 bits, setup our dma tag
	to accept up to 39bit addresses.

aic7770.c:
	Update the softc directly rather than use an intermediate
	"probe_config" structure.

aic7xxx.c:
	Complete core work to support 39bit addresses for bulk data
	dma operations.  Controller data structures still must reside
	under the 4GB boundary to reduce code/data size in the sequencer
	and related data structures.  This has been tested under Linux
	IA64 and will be tested on IA64 for FreeBSD as soon as our port
	can run there.

	Add bus dmamap synchronization calls around manipulation of
	all controller/kernel shared host data structures.

	Implement data pointer reinitialation for a second data phase
	in a single connection in the kernel rather than bloat the
	sequencer.  This is an extremely rare operation (does it ever
	happen?) and the sequencer implementation was flawed for some
	of the newest chips.

	Don't ever allow our target role to initiate a PPR.  This
	is forbidden by the SCSI spec.

	Add a few missing endian conversions in the ignore wide pointers
	code.  The core has been tested on the PPC under Linux and should
	work for FreeBSD PPC.  As soon as I can test the OSM layer for
	FreeBSD PPC, I will.

	Move some of ahc_softc_init() into ahc_alloc() now that the
	probe_config structure is gone.

	Add a 4GB boundary condition on all of our dma tags.  32bit
	DAC under PCI only works on a single 4GB "page".  Although
	we can cross 4GB on a true 64bit bus, the card won't always
	be installed in one and we can save code space and cost in
	implementing high address support by assuming the high DWORD
	address will never change.

	Add diagnostics to ahc_search_qinfifo().

	Correct a target mode issue with bus resets.  To avoid an
	interrupt storm from a malicious third party holding the
	reset line, the sequencer would defer re-enabling the reset
	interrupt until either a select-out or select-in.  Unfortunately,
	the select-in enable bit is cleared by a bus reset, so a second
	reset will render the card deaf to an initiator's attempts to
	contact it.  We now re-enable bus reset interrupts immediately
	if the target role is enabled.

aic7xxx.h:
	Remove struct ahc_probe_config.

	SCB's now contain a pointer to the sg_map_node so we can perfrom
	bus dma sync operations on the SG list prior to queuing a command.

aic7xxx.reg:
	Register the Perforce ID for this file with the VERSION keyword
	so it is printed in generated files.

	Add the DSCOMMAND1 register which is used to access the high
	DWORD of address bits.

	Add the data pointer reinitialize sequencer interrupt code.

aic7xxx.seq:
	Register the Perforce ID for this file with the VERSION keyword
	so it is printed in generated files.

	Remove code to re-enable the bus reset interrupt after a select-in.
	In target mode we cannot defer this operation as ENSELI is cleared
	by a bus reset.

	Complete 39bit support.

	Generate a sequencer inteerrupt rather than handle the data
	pointers re-initialitation in the sequencer.

	Inline the "seen identify" assertion to save a few cycles.

	Short circuit the update of our residual data if we have
	fully completed a transfer.  The residual is correct from
	our last S/G load operation.

	Short circuit full SDPTR processing if the residual is 0.
	Just mark the transfer as complete.

aic7xxx_93cx6.c:
	Synchronize perforce IDs.

aic7xxx_freebsd.c:
	Complete untested 39bit support.

	Add missing endia conversions.

	Clear our residuals prior to starting a command.  The
	update residual code in the core only sets the residual
	if there is one.

aic7xxx_freebsd.h:
	Modeify ahc_dmamap_sync() macros to take an offset and a length.
	This is how sync operations are performed in NetBSD, and we should
	update our bus dma implementation to match.

aic7xxx_inline.h:
	Add data structure synchronization helper functions.

	Fix a bug in ahc_intr() where we would not clear our unsolicited
	interrupt counter after running our PCI interrupt handler.  This
	may have been the cause of the spurious PCI interrupt messages.

aic7xxx_pci.c:
	Adjust for loss of probe_config structure.

	Guard against bogus 9005 subdevice information as seen on some
	IBM MB configurations.

	Add 39bit address support.

MFC after: 10 days
2001-07-18 21:39:48 +00:00

1954 lines
50 KiB
C
Raw Blame History

/*
* Bus independent FreeBSD shim for the aic7xxx based adaptec SCSI controllers
*
* Copyright (c) 1994-2001 Justin T. Gibbs.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions, and the following disclaimer,
* without modification.
* 2. The name of the author may not be used to endorse or promote products
* derived from this software without specific prior written permission.
*
* Alternatively, this software may be distributed under the terms of the
* GNU Public License ("GPL").
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* $Id$
*
* $FreeBSD$
*/
#include <dev/aic7xxx/aic7xxx_freebsd.h>
#include <dev/aic7xxx/aic7xxx_inline.h>
#ifndef AHC_TMODE_ENABLE
#define AHC_TMODE_ENABLE 0
#endif
#define ccb_scb_ptr spriv_ptr0
#ifdef AHC_DEBUG
static int ahc_debug = AHC_DEBUG;
#endif
#if UNUSED
static void ahc_dump_targcmd(struct target_cmd *cmd);
#endif
static int ahc_modevent(module_t mod, int type, void *data);
static void ahc_action(struct cam_sim *sim, union ccb *ccb);
static void ahc_get_tran_settings(struct ahc_softc *ahc,
int our_id, char channel,
struct ccb_trans_settings *cts);
static void ahc_async(void *callback_arg, uint32_t code,
struct cam_path *path, void *arg);
static void ahc_execute_scb(void *arg, bus_dma_segment_t *dm_segs,
int nsegments, int error);
static void ahc_poll(struct cam_sim *sim);
static void ahc_setup_data(struct ahc_softc *ahc, struct cam_sim *sim,
struct ccb_scsiio *csio, struct scb *scb);
static void ahc_abort_ccb(struct ahc_softc *ahc, struct cam_sim *sim,
union ccb *ccb);
static int ahc_create_path(struct ahc_softc *ahc,
char channel, u_int target, u_int lun,
struct cam_path **path);
static void ahc_set_recoveryscb(struct ahc_softc *ahc, struct scb *scb);
static int
ahc_create_path(struct ahc_softc *ahc, char channel, u_int target,
u_int lun, struct cam_path **path)
{
path_id_t path_id;
if (channel == 'B')
path_id = cam_sim_path(ahc->platform_data->sim_b);
else
path_id = cam_sim_path(ahc->platform_data->sim);
return (xpt_create_path(path, /*periph*/NULL,
path_id, target, lun));
}
/*
* Attach all the sub-devices we can find
*/
int
ahc_attach(struct ahc_softc *ahc)
{
char ahc_info[256];
struct ccb_setasync csa;
struct cam_devq *devq;
int bus_id;
int bus_id2;
struct cam_sim *sim;
struct cam_sim *sim2;
struct cam_path *path;
struct cam_path *path2;
long s;
int count;
int error;
count = 0;
sim = NULL;
sim2 = NULL;
ahc_controller_info(ahc, ahc_info);
printf("%s\n", ahc_info);
ahc_lock(ahc, &s);
/* Hook up our interrupt handler */
if ((error = bus_setup_intr(ahc->dev_softc, ahc->platform_data->irq,
INTR_TYPE_CAM|INTR_ENTROPY, ahc_platform_intr, ahc,
&ahc->platform_data->ih)) != 0) {
device_printf(ahc->dev_softc, "bus_setup_intr() failed: %d\n",
error);
goto fail;
}
/*
* Attach secondary channel first if the user has
* declared it the primary channel.
*/
if ((ahc->features & AHC_TWIN) != 0
&& (ahc->flags & AHC_PRIMARY_CHANNEL) != 0) {
bus_id = 1;
bus_id2 = 0;
} else {
bus_id = 0;
bus_id2 = 1;
}
/*
* Create the device queue for our SIM(s).
*/
devq = cam_simq_alloc(AHC_MAX_QUEUE);
if (devq == NULL)
goto fail;
/*
* Construct our first channel SIM entry
*/
sim = cam_sim_alloc(ahc_action, ahc_poll, "ahc", ahc,
device_get_unit(ahc->dev_softc),
1, AHC_MAX_QUEUE, devq);
if (sim == NULL) {
cam_simq_free(devq);
goto fail;
}
if (xpt_bus_register(sim, bus_id) != CAM_SUCCESS) {
cam_sim_free(sim, /*free_devq*/TRUE);
sim = NULL;
goto fail;
}
if (xpt_create_path(&path, /*periph*/NULL,
cam_sim_path(sim), CAM_TARGET_WILDCARD,
CAM_LUN_WILDCARD) != CAM_REQ_CMP) {
xpt_bus_deregister(cam_sim_path(sim));
cam_sim_free(sim, /*free_devq*/TRUE);
sim = NULL;
goto fail;
}
xpt_setup_ccb(&csa.ccb_h, path, /*priority*/5);
csa.ccb_h.func_code = XPT_SASYNC_CB;
csa.event_enable = AC_LOST_DEVICE;
csa.callback = ahc_async;
csa.callback_arg = sim;
xpt_action((union ccb *)&csa);
count++;
if (ahc->features & AHC_TWIN) {
sim2 = cam_sim_alloc(ahc_action, ahc_poll, "ahc",
ahc, device_get_unit(ahc->dev_softc), 1,
AHC_MAX_QUEUE, devq);
if (sim2 == NULL) {
printf("ahc_attach: Unable to attach second "
"bus due to resource shortage");
goto fail;
}
if (xpt_bus_register(sim2, bus_id2) != CAM_SUCCESS) {
printf("ahc_attach: Unable to attach second "
"bus due to resource shortage");
/*
* We do not want to destroy the device queue
* because the first bus is using it.
*/
cam_sim_free(sim2, /*free_devq*/FALSE);
goto fail;
}
if (xpt_create_path(&path2, /*periph*/NULL,
cam_sim_path(sim2),
CAM_TARGET_WILDCARD,
CAM_LUN_WILDCARD) != CAM_REQ_CMP) {
xpt_bus_deregister(cam_sim_path(sim2));
cam_sim_free(sim2, /*free_devq*/FALSE);
sim2 = NULL;
goto fail;
}
xpt_setup_ccb(&csa.ccb_h, path2, /*priority*/5);
csa.ccb_h.func_code = XPT_SASYNC_CB;
csa.event_enable = AC_LOST_DEVICE;
csa.callback = ahc_async;
csa.callback_arg = sim2;
xpt_action((union ccb *)&csa);
count++;
}
fail:
if ((ahc->features & AHC_TWIN) != 0
&& (ahc->flags & AHC_PRIMARY_CHANNEL) != 0) {
ahc->platform_data->sim_b = sim;
ahc->platform_data->path_b = path;
ahc->platform_data->sim = sim2;
ahc->platform_data->path = path2;
} else {
ahc->platform_data->sim = sim;
ahc->platform_data->path = path;
ahc->platform_data->sim_b = sim2;
ahc->platform_data->path_b = path2;
}
ahc_unlock(ahc, &s);
if (count != 0)
/* We have to wait until after any system dumps... */
ahc->platform_data->eh =
EVENTHANDLER_REGISTER(shutdown_final, ahc_shutdown,
ahc, SHUTDOWN_PRI_DEFAULT);
return (count);
}
/*
* Catch an interrupt from the adapter
*/
void
ahc_platform_intr(void *arg)
{
struct ahc_softc *ahc;
ahc = (struct ahc_softc *)arg;
ahc_intr(ahc);
}
/*
* We have an scb which has been processed by the
* adaptor, now we look to see how the operation
* went.
*/
void
ahc_done(struct ahc_softc *ahc, struct scb *scb)
{
union ccb *ccb;
CAM_DEBUG(scb->io_ctx->ccb_h.path, CAM_DEBUG_TRACE,
("ahc_done - scb %d\n", scb->hscb->tag));
ccb = scb->io_ctx;
LIST_REMOVE(scb, pending_links);
if ((scb->flags & SCB_UNTAGGEDQ) != 0) {
struct scb_tailq *untagged_q;
int target_offset;
target_offset = SCB_GET_TARGET_OFFSET(ahc, scb);
untagged_q = &ahc->untagged_queues[target_offset];
TAILQ_REMOVE(untagged_q, scb, links.tqe);
scb->flags &= ~SCB_UNTAGGEDQ;
ahc_run_untagged_queue(ahc, untagged_q);
}
untimeout(ahc_timeout, (caddr_t)scb, ccb->ccb_h.timeout_ch);
if ((ccb->ccb_h.flags & CAM_DIR_MASK) != CAM_DIR_NONE) {
bus_dmasync_op_t op;
if ((ccb->ccb_h.flags & CAM_DIR_MASK) == CAM_DIR_IN)
op = BUS_DMASYNC_POSTREAD;
else
op = BUS_DMASYNC_POSTWRITE;
bus_dmamap_sync(ahc->buffer_dmat, scb->dmamap, op);
bus_dmamap_unload(ahc->buffer_dmat, scb->dmamap);
}
if (ccb->ccb_h.func_code == XPT_CONT_TARGET_IO) {
struct cam_path *ccb_path;
/*
* If we have finally disconnected, clean up our
* pending device state.
* XXX - There may be error states that cause where
* we will remain connected.
*/
ccb_path = ccb->ccb_h.path;
if (ahc->pending_device != NULL
&& xpt_path_comp(ahc->pending_device->path, ccb_path) == 0) {
if ((ccb->ccb_h.flags & CAM_SEND_STATUS) != 0) {
ahc->pending_device = NULL;
} else {
xpt_print_path(ccb->ccb_h.path);
printf("Still disconnected\n");
ahc_freeze_ccb(ccb);
}
}
if (ahc_get_transaction_status(scb) == CAM_REQ_INPROG)
ccb->ccb_h.status |= CAM_REQ_CMP;
ccb->ccb_h.status &= ~CAM_SIM_QUEUED;
ahc_free_scb(ahc, scb);
xpt_done(ccb);
return;
}
/*
* If the recovery SCB completes, we have to be
* out of our timeout.
*/
if ((scb->flags & SCB_RECOVERY_SCB) != 0) {
struct scb *list_scb;
/*
* We were able to complete the command successfully,
* so reinstate the timeouts for all other pending
* commands.
*/
LIST_FOREACH(list_scb, &ahc->pending_scbs, pending_links) {
union ccb *ccb;
uint64_t time;
ccb = list_scb->io_ctx;
if (ccb->ccb_h.timeout == CAM_TIME_INFINITY)
continue;
time = ccb->ccb_h.timeout;
time *= hz;
time /= 1000;
ccb->ccb_h.timeout_ch =
timeout(ahc_timeout, list_scb, time);
}
if (ahc_get_transaction_status(scb) == CAM_BDR_SENT
|| ahc_get_transaction_status(scb) == CAM_REQ_ABORTED)
ahc_set_transaction_status(scb, CAM_CMD_TIMEOUT);
ahc_print_path(ahc, scb);
printf("no longer in timeout, status = %x\n",
ccb->ccb_h.status);
}
/* Don't clobber any existing error state */
if (ahc_get_transaction_status(scb) == CAM_REQ_INPROG) {
ccb->ccb_h.status |= CAM_REQ_CMP;
} else if ((scb->flags & SCB_SENSE) != 0) {
/*
* We performed autosense retrieval.
*
* Zero any sense not transferred by the
* device. The SCSI spec mandates that any
* untransfered data should be assumed to be
* zero. Complete the 'bounce' of sense information
* through buffers accessible via bus-space by
* copying it into the clients csio.
*/
memset(&ccb->csio.sense_data, 0, sizeof(ccb->csio.sense_data));
memcpy(&ccb->csio.sense_data,
ahc_get_sense_buf(ahc, scb),
(scb->sg_list->len & AHC_SG_LEN_MASK)
- ccb->csio.sense_resid);
scb->io_ctx->ccb_h.status |= CAM_AUTOSNS_VALID;
}
ccb->ccb_h.status &= ~CAM_SIM_QUEUED;
ahc_free_scb(ahc, scb);
xpt_done(ccb);
}
static void
ahc_action(struct cam_sim *sim, union ccb *ccb)
{
struct ahc_softc *ahc;
struct ahc_tmode_lstate *lstate;
u_int target_id;
u_int our_id;
long s;
CAM_DEBUG(ccb->ccb_h.path, CAM_DEBUG_TRACE, ("ahc_action\n"));
ahc = (struct ahc_softc *)cam_sim_softc(sim);
target_id = ccb->ccb_h.target_id;
our_id = SIM_SCSI_ID(ahc, sim);
switch (ccb->ccb_h.func_code) {
/* Common cases first */
case XPT_ACCEPT_TARGET_IO: /* Accept Host Target Mode CDB */
case XPT_CONT_TARGET_IO:/* Continue Host Target I/O Connection*/
{
struct ahc_tmode_tstate *tstate;
cam_status status;
status = ahc_find_tmode_devs(ahc, sim, ccb, &tstate,
&lstate, TRUE);
if (status != CAM_REQ_CMP) {
if (ccb->ccb_h.func_code == XPT_CONT_TARGET_IO) {
/* Response from the black hole device */
tstate = NULL;
lstate = ahc->black_hole;
} else {
ccb->ccb_h.status = status;
xpt_done(ccb);
break;
}
}
if (ccb->ccb_h.func_code == XPT_ACCEPT_TARGET_IO) {
ahc_lock(ahc, &s);
SLIST_INSERT_HEAD(&lstate->accept_tios, &ccb->ccb_h,
sim_links.sle);
ccb->ccb_h.status = CAM_REQ_INPROG;
if ((ahc->flags & AHC_TQINFIFO_BLOCKED) != 0)
ahc_run_tqinfifo(ahc, /*paused*/FALSE);
ahc_unlock(ahc, &s);
break;
}
/*
* The target_id represents the target we attempt to
* select. In target mode, this is the initiator of
* the original command.
*/
our_id = target_id;
target_id = ccb->csio.init_id;
/* FALLTHROUGH */
}
case XPT_SCSI_IO: /* Execute the requested I/O operation */
case XPT_RESET_DEV: /* Bus Device Reset the specified SCSI device */
{
struct scb *scb;
struct hardware_scb *hscb;
if ((ahc->flags & AHC_INITIATORROLE) == 0
&& (ccb->ccb_h.func_code == XPT_SCSI_IO
|| ccb->ccb_h.func_code == XPT_RESET_DEV)) {
ccb->ccb_h.status = CAM_PROVIDE_FAIL;
xpt_done(ccb);
return;
}
/*
* get an scb to use.
*/
ahc_lock(ahc, &s);
if ((scb = ahc_get_scb(ahc)) == NULL) {
xpt_freeze_simq(sim, /*count*/1);
ahc->flags |= AHC_RESOURCE_SHORTAGE;
ahc_unlock(ahc, &s);
ccb->ccb_h.status = CAM_REQUEUE_REQ;
xpt_done(ccb);
return;
}
ahc_unlock(ahc, &s);
hscb = scb->hscb;
CAM_DEBUG(ccb->ccb_h.path, CAM_DEBUG_SUBTRACE,
("start scb(%p)\n", scb));
scb->io_ctx = ccb;
/*
* So we can find the SCB when an abort is requested
*/
ccb->ccb_h.ccb_scb_ptr = scb;
/*
* Put all the arguments for the xfer in the scb
*/
hscb->control = 0;
hscb->scsiid = BUILD_SCSIID(ahc, sim, target_id, our_id);
hscb->lun = ccb->ccb_h.target_lun;
if (ccb->ccb_h.func_code == XPT_RESET_DEV) {
hscb->cdb_len = 0;
scb->flags |= SCB_DEVICE_RESET;
hscb->control |= MK_MESSAGE;
ahc_execute_scb(scb, NULL, 0, 0);
} else {
if (ccb->ccb_h.func_code == XPT_CONT_TARGET_IO) {
struct target_data *tdata;
tdata = &hscb->shared_data.tdata;
if (ahc->pending_device == lstate)
scb->flags |= SCB_TARGET_IMMEDIATE;
hscb->control |= TARGET_SCB;
tdata->target_phases = IDENTIFY_SEEN;
if ((ccb->ccb_h.flags & CAM_SEND_STATUS) != 0) {
tdata->target_phases |= SPHASE_PENDING;
tdata->scsi_status =
ccb->csio.scsi_status;
}
if (ccb->ccb_h.flags & CAM_DIS_DISCONNECT)
tdata->target_phases |= NO_DISCONNECT;
tdata->initiator_tag = ccb->csio.tag_id;
}
if (ccb->ccb_h.flags & CAM_TAG_ACTION_VALID)
hscb->control |= ccb->csio.tag_action;
ahc_setup_data(ahc, sim, &ccb->csio, scb);
}
break;
}
case XPT_NOTIFY_ACK:
case XPT_IMMED_NOTIFY:
{
struct ahc_tmode_tstate *tstate;
struct ahc_tmode_lstate *lstate;
cam_status status;
status = ahc_find_tmode_devs(ahc, sim, ccb, &tstate,
&lstate, TRUE);
if (status != CAM_REQ_CMP) {
ccb->ccb_h.status = status;
xpt_done(ccb);
break;
}
SLIST_INSERT_HEAD(&lstate->immed_notifies, &ccb->ccb_h,
sim_links.sle);
ccb->ccb_h.status = CAM_REQ_INPROG;
ahc_send_lstate_events(ahc, lstate);
break;
}
case XPT_EN_LUN: /* Enable LUN as a target */
ahc_handle_en_lun(ahc, sim, ccb);
xpt_done(ccb);
break;
case XPT_ABORT: /* Abort the specified CCB */
{
ahc_abort_ccb(ahc, sim, ccb);
break;
}
case XPT_SET_TRAN_SETTINGS:
{
#ifdef AHC_NEW_TRAN_SETTINGS
struct ahc_devinfo devinfo;
struct ccb_trans_settings *cts;
struct ccb_trans_settings_scsi *scsi;
struct ccb_trans_settings_spi *spi;
struct ahc_initiator_tinfo *tinfo;
struct ahc_tmode_tstate *tstate;
uint16_t *discenable;
uint16_t *tagenable;
u_int update_type;
cts = &ccb->cts;
scsi = &cts->proto_specific.scsi;
spi = &cts->xport_specific.spi;
ahc_compile_devinfo(&devinfo, SIM_SCSI_ID(ahc, sim),
cts->ccb_h.target_id,
cts->ccb_h.target_lun,
SIM_CHANNEL(ahc, sim),
ROLE_UNKNOWN);
tinfo = ahc_fetch_transinfo(ahc, devinfo.channel,
devinfo.our_scsiid,
devinfo.target, &tstate);
update_type = 0;
if (cts->type == CTS_TYPE_CURRENT_SETTINGS) {
update_type |= AHC_TRANS_GOAL;
discenable = &tstate->discenable;
tagenable = &tstate->tagenable;
tinfo->curr.protocol_version =
cts->protocol_version;
tinfo->curr.transport_version =
cts->transport_version;
tinfo->goal.protocol_version =
cts->protocol_version;
tinfo->goal.transport_version =
cts->transport_version;
} else if (cts->type == CTS_TYPE_USER_SETTINGS) {
update_type |= AHC_TRANS_USER;
discenable = &ahc->user_discenable;
tagenable = &ahc->user_tagenable;
tinfo->user.protocol_version =
cts->protocol_version;
tinfo->user.transport_version =
cts->transport_version;
} else {
ccb->ccb_h.status = CAM_REQ_INVALID;
xpt_done(ccb);
break;
}
ahc_lock(ahc, &s);
if ((spi->valid & CTS_SPI_VALID_DISC) != 0) {
if ((spi->flags & CTS_SPI_FLAGS_DISC_ENB) != 0)
*discenable |= devinfo.target_mask;
else
*discenable &= ~devinfo.target_mask;
}
if ((scsi->valid & CTS_SCSI_VALID_TQ) != 0) {
if ((scsi->flags & CTS_SCSI_FLAGS_TAG_ENB) != 0)
*tagenable |= devinfo.target_mask;
else
*tagenable &= ~devinfo.target_mask;
}
if ((spi->valid & CTS_SPI_VALID_BUS_WIDTH) != 0) {
ahc_validate_width(ahc, /*tinfo limit*/NULL,
&spi->bus_width, ROLE_UNKNOWN);
ahc_set_width(ahc, &devinfo, spi->bus_width,
update_type, /*paused*/FALSE);
}
if ((spi->valid & CTS_SPI_VALID_PPR_OPTIONS) == 0) {
if (update_type == AHC_TRANS_USER)
spi->ppr_options = tinfo->user.ppr_options;
else
spi->ppr_options = tinfo->goal.ppr_options;
}
if ((spi->valid & CTS_SPI_VALID_SYNC_OFFSET) == 0) {
if (update_type == AHC_TRANS_USER)
spi->sync_offset = tinfo->user.offset;
else
spi->sync_offset = tinfo->goal.offset;
}
if ((spi->valid & CTS_SPI_VALID_SYNC_RATE) == 0) {
if (update_type == AHC_TRANS_USER)
spi->sync_period = tinfo->user.period;
else
spi->sync_period = tinfo->goal.period;
}
if (((spi->valid & CTS_SPI_VALID_SYNC_RATE) != 0)
|| ((spi->valid & CTS_SPI_VALID_SYNC_OFFSET) != 0)) {
struct ahc_syncrate *syncrate;
u_int maxsync;
if ((ahc->features & AHC_ULTRA2) != 0)
maxsync = AHC_SYNCRATE_DT;
else if ((ahc->features & AHC_ULTRA) != 0)
maxsync = AHC_SYNCRATE_ULTRA;
else
maxsync = AHC_SYNCRATE_FAST;
syncrate = ahc_find_syncrate(ahc, &spi->sync_period,
&spi->ppr_options,
maxsync);
ahc_validate_offset(ahc, /*tinfo limit*/NULL,
syncrate, &spi->sync_offset,
spi->bus_width, ROLE_UNKNOWN);
/* We use a period of 0 to represent async */
if (spi->sync_offset == 0) {
spi->sync_period = 0;
spi->ppr_options = 0;
}
ahc_set_syncrate(ahc, &devinfo, syncrate,
spi->sync_period, spi->sync_offset,
spi->ppr_options, update_type,
/*paused*/FALSE);
}
ahc_unlock(ahc, &s);
ccb->ccb_h.status = CAM_REQ_CMP;
xpt_done(ccb);
#else
struct ahc_devinfo devinfo;
struct ccb_trans_settings *cts;
struct ahc_initiator_tinfo *tinfo;
struct ahc_tmode_tstate *tstate;
uint16_t *discenable;
uint16_t *tagenable;
u_int update_type;
long s;
cts = &ccb->cts;
ahc_compile_devinfo(&devinfo, SIM_SCSI_ID(ahc, sim),
cts->ccb_h.target_id,
cts->ccb_h.target_lun,
SIM_CHANNEL(ahc, sim),
ROLE_UNKNOWN);
tinfo = ahc_fetch_transinfo(ahc, devinfo.channel,
devinfo.our_scsiid,
devinfo.target, &tstate);
update_type = 0;
if ((cts->flags & CCB_TRANS_CURRENT_SETTINGS) != 0) {
update_type |= AHC_TRANS_GOAL;
discenable = &tstate->discenable;
tagenable = &tstate->tagenable;
} else if ((cts->flags & CCB_TRANS_USER_SETTINGS) != 0) {
update_type |= AHC_TRANS_USER;
discenable = &ahc->user_discenable;
tagenable = &ahc->user_tagenable;
} else {
ccb->ccb_h.status = CAM_REQ_INVALID;
xpt_done(ccb);
break;
}
ahc_lock(ahc, &s);
if ((cts->valid & CCB_TRANS_DISC_VALID) != 0) {
if ((cts->flags & CCB_TRANS_DISC_ENB) != 0)
*discenable |= devinfo.target_mask;
else
*discenable &= ~devinfo.target_mask;
}
if ((cts->valid & CCB_TRANS_TQ_VALID) != 0) {
if ((cts->flags & CCB_TRANS_TAG_ENB) != 0)
*tagenable |= devinfo.target_mask;
else
*tagenable &= ~devinfo.target_mask;
}
if ((cts->valid & CCB_TRANS_BUS_WIDTH_VALID) != 0) {
ahc_validate_width(ahc, /*tinfo limit*/NULL,
&cts->bus_width, ROLE_UNKNOWN);
ahc_set_width(ahc, &devinfo, cts->bus_width,
update_type, /*paused*/FALSE);
}
if ((cts->valid & CCB_TRANS_SYNC_OFFSET_VALID) == 0) {
if (update_type == AHC_TRANS_USER)
cts->sync_offset = tinfo->user.offset;
else
cts->sync_offset = tinfo->goal.offset;
}
if ((cts->valid & CCB_TRANS_SYNC_RATE_VALID) == 0) {
if (update_type == AHC_TRANS_USER)
cts->sync_period = tinfo->user.period;
else
cts->sync_period = tinfo->goal.period;
}
if (((cts->valid & CCB_TRANS_SYNC_RATE_VALID) != 0)
|| ((cts->valid & CCB_TRANS_SYNC_OFFSET_VALID) != 0)) {
struct ahc_syncrate *syncrate;
u_int ppr_options;
u_int maxsync;
if ((ahc->features & AHC_ULTRA2) != 0)
maxsync = AHC_SYNCRATE_DT;
else if ((ahc->features & AHC_ULTRA) != 0)
maxsync = AHC_SYNCRATE_ULTRA;
else
maxsync = AHC_SYNCRATE_FAST;
ppr_options = 0;
if (cts->sync_period <= 9)
ppr_options = MSG_EXT_PPR_DT_REQ;
syncrate = ahc_find_syncrate(ahc, &cts->sync_period,
&ppr_options,
maxsync);
ahc_validate_offset(ahc, /*tinfo limit*/NULL,
syncrate, &cts->sync_offset,
MSG_EXT_WDTR_BUS_8_BIT,
ROLE_UNKNOWN);
/* We use a period of 0 to represent async */
if (cts->sync_offset == 0) {
cts->sync_period = 0;
ppr_options = 0;
}
if (ppr_options == MSG_EXT_PPR_DT_REQ
&& tinfo->user.transport_version >= 3) {
tinfo->goal.transport_version =
tinfo->user.transport_version;
tinfo->curr.transport_version =
tinfo->user.transport_version;
}
ahc_set_syncrate(ahc, &devinfo, syncrate,
cts->sync_period, cts->sync_offset,
ppr_options, update_type,
/*paused*/FALSE);
}
ahc_unlock(ahc, &s);
ccb->ccb_h.status = CAM_REQ_CMP;
xpt_done(ccb);
#endif
break;
}
case XPT_GET_TRAN_SETTINGS:
/* Get default/user set transfer settings for the target */
{
ahc_lock(ahc, &s);
ahc_get_tran_settings(ahc, SIM_SCSI_ID(ahc, sim),
SIM_CHANNEL(ahc, sim), &ccb->cts);
ahc_unlock(ahc, &s);
xpt_done(ccb);
break;
}
case XPT_CALC_GEOMETRY:
{
struct ccb_calc_geometry *ccg;
uint32_t size_mb;
uint32_t secs_per_cylinder;
int extended;
ccg = &ccb->ccg;
size_mb = ccg->volume_size
/ ((1024L * 1024L) / ccg->block_size);
extended = SIM_IS_SCSIBUS_B(ahc, sim)
? ahc->flags & AHC_EXTENDED_TRANS_B
: ahc->flags & AHC_EXTENDED_TRANS_A;
if (size_mb > 1024 && extended) {
ccg->heads = 255;
ccg->secs_per_track = 63;
} else {
ccg->heads = 64;
ccg->secs_per_track = 32;
}
secs_per_cylinder = ccg->heads * ccg->secs_per_track;
ccg->cylinders = ccg->volume_size / secs_per_cylinder;
ccb->ccb_h.status = CAM_REQ_CMP;
xpt_done(ccb);
break;
}
case XPT_RESET_BUS: /* Reset the specified SCSI bus */
{
int found;
ahc_lock(ahc, &s);
found = ahc_reset_channel(ahc, SIM_CHANNEL(ahc, sim),
/*initiate reset*/TRUE);
ahc_unlock(ahc, &s);
if (bootverbose) {
xpt_print_path(SIM_PATH(ahc, sim));
printf("SCSI bus reset delivered. "
"%d SCBs aborted.\n", found);
}
ccb->ccb_h.status = CAM_REQ_CMP;
xpt_done(ccb);
break;
}
case XPT_TERM_IO: /* Terminate the I/O process */
/* XXX Implement */
ccb->ccb_h.status = CAM_REQ_INVALID;
xpt_done(ccb);
break;
case XPT_PATH_INQ: /* Path routing inquiry */
{
struct ccb_pathinq *cpi = &ccb->cpi;
cpi->version_num = 1; /* XXX??? */
cpi->hba_inquiry = PI_SDTR_ABLE|PI_TAG_ABLE;
if ((ahc->features & AHC_WIDE) != 0)
cpi->hba_inquiry |= PI_WIDE_16;
if ((ahc->features & AHC_TARGETMODE) != 0) {
cpi->target_sprt = PIT_PROCESSOR
| PIT_DISCONNECT
| PIT_TERM_IO;
} else {
cpi->target_sprt = 0;
}
cpi->hba_misc = 0;
cpi->hba_eng_cnt = 0;
cpi->max_target = (ahc->features & AHC_WIDE) ? 15 : 7;
cpi->max_lun = AHC_NUM_LUNS - 1;
if (SIM_IS_SCSIBUS_B(ahc, sim)) {
cpi->initiator_id = ahc->our_id_b;
if ((ahc->flags & AHC_RESET_BUS_B) == 0)
cpi->hba_misc |= PIM_NOBUSRESET;
} else {
cpi->initiator_id = ahc->our_id;
if ((ahc->flags & AHC_RESET_BUS_A) == 0)
cpi->hba_misc |= PIM_NOBUSRESET;
}
cpi->bus_id = cam_sim_bus(sim);
cpi->base_transfer_speed = 3300;
strncpy(cpi->sim_vid, "FreeBSD", SIM_IDLEN);
strncpy(cpi->hba_vid, "Adaptec", HBA_IDLEN);
strncpy(cpi->dev_name, cam_sim_name(sim), DEV_IDLEN);
cpi->unit_number = cam_sim_unit(sim);
#ifdef AHC_NEW_TRAN_SETTINGS
cpi->protocol = PROTO_SCSI;
cpi->protocol_version = SCSI_REV_2;
cpi->transport = XPORT_SPI;
cpi->transport_version = 2;
cpi->xport_specific.spi.ppr_options = SID_SPI_CLOCK_ST;
if ((ahc->features & AHC_DT) != 0) {
cpi->transport_version = 3;
cpi->xport_specific.spi.ppr_options =
SID_SPI_CLOCK_DT_ST;
}
#endif
cpi->ccb_h.status = CAM_REQ_CMP;
xpt_done(ccb);
break;
}
default:
ccb->ccb_h.status = CAM_PROVIDE_FAIL;
xpt_done(ccb);
break;
}
}
static void
ahc_get_tran_settings(struct ahc_softc *ahc, int our_id, char channel,
struct ccb_trans_settings *cts)
{
#ifdef AHC_NEW_TRAN_SETTINGS
struct ahc_devinfo devinfo;
struct ccb_trans_settings_scsi *scsi;
struct ccb_trans_settings_spi *spi;
struct ahc_initiator_tinfo *targ_info;
struct ahc_tmode_tstate *tstate;
struct ahc_transinfo *tinfo;
scsi = &cts->proto_specific.scsi;
spi = &cts->xport_specific.spi;
ahc_compile_devinfo(&devinfo, our_id,
cts->ccb_h.target_id,
cts->ccb_h.target_lun,
channel, ROLE_UNKNOWN);
targ_info = ahc_fetch_transinfo(ahc, devinfo.channel,
devinfo.our_scsiid,
devinfo.target, &tstate);
if (cts->type == CTS_TYPE_CURRENT_SETTINGS)
tinfo = &targ_info->curr;
else
tinfo = &targ_info->user;
scsi->flags &= ~CTS_SCSI_FLAGS_TAG_ENB;
spi->flags &= ~CTS_SPI_FLAGS_DISC_ENB;
if (cts->type == CTS_TYPE_USER_SETTINGS) {
if ((ahc->user_discenable & devinfo.target_mask) != 0)
spi->flags |= CTS_SPI_FLAGS_DISC_ENB;
if ((ahc->user_tagenable & devinfo.target_mask) != 0)
scsi->flags |= CTS_SCSI_FLAGS_TAG_ENB;
} else {
if ((tstate->discenable & devinfo.target_mask) != 0)
spi->flags |= CTS_SPI_FLAGS_DISC_ENB;
if ((tstate->tagenable & devinfo.target_mask) != 0)
scsi->flags |= CTS_SCSI_FLAGS_TAG_ENB;
}
cts->protocol_version = tinfo->protocol_version;
cts->transport_version = tinfo->transport_version;
spi->sync_period = tinfo->period;
spi->sync_offset = tinfo->offset;
spi->bus_width = tinfo->width;
spi->ppr_options = tinfo->ppr_options;
cts->protocol = PROTO_SCSI;
cts->transport = XPORT_SPI;
spi->valid = CTS_SPI_VALID_SYNC_RATE
| CTS_SPI_VALID_SYNC_OFFSET
| CTS_SPI_VALID_BUS_WIDTH
| CTS_SPI_VALID_PPR_OPTIONS;
if (cts->ccb_h.target_lun != CAM_LUN_WILDCARD) {
scsi->valid = CTS_SCSI_VALID_TQ;
spi->valid |= CTS_SPI_VALID_DISC;
} else {
scsi->valid = 0;
}
cts->ccb_h.status = CAM_REQ_CMP;
#else
struct ahc_devinfo devinfo;
struct ahc_initiator_tinfo *targ_info;
struct ahc_tmode_tstate *tstate;
struct ahc_transinfo *tinfo;
long s;
ahc_compile_devinfo(&devinfo, our_id,
cts->ccb_h.target_id,
cts->ccb_h.target_lun,
channel, ROLE_UNKNOWN);
targ_info = ahc_fetch_transinfo(ahc, devinfo.channel,
devinfo.our_scsiid,
devinfo.target, &tstate);
if ((cts->flags & CCB_TRANS_CURRENT_SETTINGS) != 0)
tinfo = &targ_info->curr;
else
tinfo = &targ_info->user;
ahc_lock(ahc, &s);
cts->flags &= ~(CCB_TRANS_DISC_ENB|CCB_TRANS_TAG_ENB);
if ((cts->flags & CCB_TRANS_CURRENT_SETTINGS) == 0) {
if ((ahc->user_discenable & devinfo.target_mask) != 0)
cts->flags |= CCB_TRANS_DISC_ENB;
if ((ahc->user_tagenable & devinfo.target_mask) != 0)
cts->flags |= CCB_TRANS_TAG_ENB;
} else {
if ((tstate->discenable & devinfo.target_mask) != 0)
cts->flags |= CCB_TRANS_DISC_ENB;
if ((tstate->tagenable & devinfo.target_mask) != 0)
cts->flags |= CCB_TRANS_TAG_ENB;
}
cts->sync_period = tinfo->period;
cts->sync_offset = tinfo->offset;
cts->bus_width = tinfo->width;
ahc_unlock(ahc, &s);
cts->valid = CCB_TRANS_SYNC_RATE_VALID
| CCB_TRANS_SYNC_OFFSET_VALID
| CCB_TRANS_BUS_WIDTH_VALID;
if (cts->ccb_h.target_lun != CAM_LUN_WILDCARD)
cts->valid |= CCB_TRANS_DISC_VALID|CCB_TRANS_TQ_VALID;
cts->ccb_h.status = CAM_REQ_CMP;
#endif
}
static void
ahc_async(void *callback_arg, uint32_t code, struct cam_path *path, void *arg)
{
struct ahc_softc *ahc;
struct cam_sim *sim;
sim = (struct cam_sim *)callback_arg;
ahc = (struct ahc_softc *)cam_sim_softc(sim);
switch (code) {
case AC_LOST_DEVICE:
{
struct ahc_devinfo devinfo;
long s;
ahc_compile_devinfo(&devinfo, SIM_SCSI_ID(ahc, sim),
xpt_path_target_id(path),
xpt_path_lun_id(path),
SIM_CHANNEL(ahc, sim),
ROLE_UNKNOWN);
/*
* Revert to async/narrow transfers
* for the next device.
*/
ahc_lock(ahc, &s);
ahc_set_width(ahc, &devinfo, MSG_EXT_WDTR_BUS_8_BIT,
AHC_TRANS_GOAL|AHC_TRANS_CUR, /*paused*/FALSE);
ahc_set_syncrate(ahc, &devinfo, /*syncrate*/NULL,
/*period*/0, /*offset*/0, /*ppr_options*/0,
AHC_TRANS_GOAL|AHC_TRANS_CUR,
/*paused*/FALSE);
ahc_unlock(ahc, &s);
break;
}
default:
break;
}
}
static void
ahc_execute_scb(void *arg, bus_dma_segment_t *dm_segs, int nsegments,
int error)
{
struct scb *scb;
union ccb *ccb;
struct ahc_softc *ahc;
struct ahc_initiator_tinfo *tinfo;
struct ahc_tmode_tstate *tstate;
u_int mask;
long s;
scb = (struct scb *)arg;
ccb = scb->io_ctx;
ahc = scb->ahc_softc;
if (error != 0) {
if (error == EFBIG)
ahc_set_transaction_status(scb, CAM_REQ_TOO_BIG);
else
ahc_set_transaction_status(scb, CAM_REQ_CMP_ERR);
if (nsegments != 0)
bus_dmamap_unload(ahc->buffer_dmat, scb->dmamap);
ahc_lock(ahc, &s);
ahc_free_scb(ahc, scb);
ahc_unlock(ahc, &s);
xpt_done(ccb);
return;
}
if (nsegments != 0) {
struct ahc_dma_seg *sg;
bus_dma_segment_t *end_seg;
bus_dmasync_op_t op;
end_seg = dm_segs + nsegments;
/* Copy the segments into our SG list */
sg = scb->sg_list;
while (dm_segs < end_seg) {
uint32_t len;
sg->addr = ahc_htole32(dm_segs->ds_addr);
len = dm_segs->ds_len
| ((dm_segs->ds_addr >> 8) & 0x7F000000);
sg->len = ahc_htole32(len);
sg++;
dm_segs++;
}
/*
* Note where to find the SG entries in bus space.
* We also set the full residual flag which the
* sequencer will clear as soon as a data transfer
* occurs.
*/
scb->hscb->sgptr = ahc_htole32(scb->sg_list_phys|SG_FULL_RESID);
if ((ccb->ccb_h.flags & CAM_DIR_MASK) == CAM_DIR_IN)
op = BUS_DMASYNC_PREREAD;
else
op = BUS_DMASYNC_PREWRITE;
bus_dmamap_sync(ahc->buffer_dmat, scb->dmamap, op);
if (ccb->ccb_h.func_code == XPT_CONT_TARGET_IO) {
struct target_data *tdata;
tdata = &scb->hscb->shared_data.tdata;
tdata->target_phases |= DPHASE_PENDING;
if ((ccb->ccb_h.flags & CAM_DIR_MASK) == CAM_DIR_OUT)
tdata->data_phase = P_DATAOUT;
else
tdata->data_phase = P_DATAIN;
/*
* If the transfer is of an odd length and in the
* "in" direction (scsi->HostBus), then it may
* trigger a bug in the 'WideODD' feature of
* non-Ultra2 chips. Force the total data-length
* to be even by adding an extra, 1 byte, SG,
* element. We do this even if we are not currently
* negotiated wide as negotiation could occur before
* this command is executed.
*/
if ((ahc->bugs & AHC_TMODE_WIDEODD_BUG) != 0
&& (ccb->csio.dxfer_len & 0x1) != 0
&& (ccb->ccb_h.flags & CAM_DIR_MASK) == CAM_DIR_IN) {
nsegments++;
if (nsegments > AHC_NSEG) {
ahc_set_transaction_status(scb,
CAM_REQ_TOO_BIG);
bus_dmamap_unload(ahc->buffer_dmat,
scb->dmamap);
ahc_lock(ahc, &s);
ahc_free_scb(ahc, scb);
ahc_unlock(ahc, &s);
xpt_done(ccb);
return;
}
sg->addr = ahc_htole32(ahc->dma_bug_buf);
sg->len = ahc_htole32(1);
sg++;
}
}
sg--;
sg->len |= ahc_htole32(AHC_DMA_LAST_SEG);
/* Copy the first SG into the "current" data pointer area */
scb->hscb->dataptr = scb->sg_list->addr;
scb->hscb->datacnt = scb->sg_list->len;
} else {
scb->hscb->sgptr = SG_LIST_NULL;
scb->hscb->dataptr = 0;
scb->hscb->datacnt = 0;
}
scb->sg_count = nsegments;
ahc_lock(ahc, &s);
/*
* Last time we need to check if this SCB needs to
* be aborted.
*/
if (ahc_get_transaction_status(scb) != CAM_REQ_INPROG) {
if (nsegments != 0)
bus_dmamap_unload(ahc->buffer_dmat,
scb->dmamap);
ahc_free_scb(ahc, scb);
ahc_unlock(ahc, &s);
xpt_done(ccb);
return;
}
tinfo = ahc_fetch_transinfo(ahc, SCSIID_CHANNEL(ahc, scb->hscb->scsiid),
SCSIID_OUR_ID(scb->hscb->scsiid),
SCSIID_TARGET(ahc, scb->hscb->scsiid),
&tstate);
mask = SCB_GET_TARGET_MASK(ahc, scb);
scb->hscb->scsirate = tinfo->scsirate;
scb->hscb->scsioffset = tinfo->curr.offset;
if ((tstate->ultraenb & mask) != 0)
scb->hscb->control |= ULTRAENB;
if ((tstate->discenable & mask) != 0
&& (ccb->ccb_h.flags & CAM_DIS_DISCONNECT) == 0)
scb->hscb->control |= DISCENB;
if ((ccb->ccb_h.flags & CAM_NEGOTIATE) != 0
&& (tinfo->goal.width != 0
|| tinfo->goal.period != 0
|| tinfo->goal.ppr_options != 0)) {
scb->flags |= SCB_NEGOTIATE;
scb->hscb->control |= MK_MESSAGE;
} else if ((tstate->auto_negotiate & mask) != 0) {
scb->flags |= SCB_AUTO_NEGOTIATE;
scb->hscb->control |= MK_MESSAGE;
}
LIST_INSERT_HEAD(&ahc->pending_scbs, scb, pending_links);
ccb->ccb_h.status |= CAM_SIM_QUEUED;
if (ccb->ccb_h.timeout != CAM_TIME_INFINITY) {
uint64_t time;
if (ccb->ccb_h.timeout == CAM_TIME_DEFAULT)
ccb->ccb_h.timeout = 5 * 1000;
time = ccb->ccb_h.timeout;
time *= hz;
time /= 1000;
ccb->ccb_h.timeout_ch =
timeout(ahc_timeout, (caddr_t)scb, time);
}
/*
* We only allow one untagged transaction
* per target in the initiator role unless
* we are storing a full busy target *lun*
* table in SCB space.
*/
if ((scb->hscb->control & (TARGET_SCB|TAG_ENB)) == 0
&& (ahc->flags & AHC_SCB_BTT) == 0) {
struct scb_tailq *untagged_q;
int target_offset;
target_offset = SCB_GET_TARGET_OFFSET(ahc, scb);
untagged_q = &(ahc->untagged_queues[target_offset]);
TAILQ_INSERT_TAIL(untagged_q, scb, links.tqe);
scb->flags |= SCB_UNTAGGEDQ;
if (TAILQ_FIRST(untagged_q) != scb) {
ahc_unlock(ahc, &s);
return;
}
}
scb->flags |= SCB_ACTIVE;
if ((scb->flags & SCB_TARGET_IMMEDIATE) != 0) {
/* Define a mapping from our tag to the SCB. */
ahc->scb_data->scbindex[scb->hscb->tag] = scb;
ahc_pause(ahc);
if ((ahc->flags & AHC_PAGESCBS) == 0)
ahc_outb(ahc, SCBPTR, scb->hscb->tag);
ahc_outb(ahc, SCB_TAG, scb->hscb->tag);
ahc_outb(ahc, RETURN_1, CONT_MSG_LOOP);
ahc_unpause(ahc);
} else {
ahc_queue_scb(ahc, scb);
}
ahc_unlock(ahc, &s);
}
static void
ahc_poll(struct cam_sim *sim)
{
ahc_intr(cam_sim_softc(sim));
}
static void
ahc_setup_data(struct ahc_softc *ahc, struct cam_sim *sim,
struct ccb_scsiio *csio, struct scb *scb)
{
struct hardware_scb *hscb;
struct ccb_hdr *ccb_h;
hscb = scb->hscb;
ccb_h = &csio->ccb_h;
csio->resid = 0;
csio->sense_resid = 0;
if (ccb_h->func_code == XPT_SCSI_IO) {
hscb->cdb_len = csio->cdb_len;
if ((ccb_h->flags & CAM_CDB_POINTER) != 0) {
if (hscb->cdb_len > sizeof(hscb->cdb32)
|| (ccb_h->flags & CAM_CDB_PHYS) != 0) {
u_long s;
ahc_set_transaction_status(scb,
CAM_REQ_INVALID);
ahc_lock(ahc, &s);
ahc_free_scb(ahc, scb);
ahc_unlock(ahc, &s);
xpt_done((union ccb *)csio);
return;
}
if (hscb->cdb_len > 12) {
memcpy(hscb->cdb32,
csio->cdb_io.cdb_ptr,
hscb->cdb_len);
scb->flags |= SCB_CDB32_PTR;
} else {
memcpy(hscb->shared_data.cdb,
csio->cdb_io.cdb_ptr,
hscb->cdb_len);
}
} else {
if (hscb->cdb_len > 12) {
memcpy(hscb->cdb32, csio->cdb_io.cdb_bytes,
hscb->cdb_len);
scb->flags |= SCB_CDB32_PTR;
} else {
memcpy(hscb->shared_data.cdb,
csio->cdb_io.cdb_bytes,
hscb->cdb_len);
}
}
}
/* Only use S/G if there is a transfer */
if ((ccb_h->flags & CAM_DIR_MASK) != CAM_DIR_NONE) {
if ((ccb_h->flags & CAM_SCATTER_VALID) == 0) {
/* We've been given a pointer to a single buffer */
if ((ccb_h->flags & CAM_DATA_PHYS) == 0) {
int s;
int error;
s = splsoftvm();
error = bus_dmamap_load(ahc->buffer_dmat,
scb->dmamap,
csio->data_ptr,
csio->dxfer_len,
ahc_execute_scb,
scb, /*flags*/0);
if (error == EINPROGRESS) {
/*
* So as to maintain ordering,
* freeze the controller queue
* until our mapping is
* returned.
*/
xpt_freeze_simq(sim,
/*count*/1);
scb->io_ctx->ccb_h.status |=
CAM_RELEASE_SIMQ;
}
splx(s);
} else {
struct bus_dma_segment seg;
/* Pointer to physical buffer */
if (csio->dxfer_len > AHC_MAXTRANSFER_SIZE)
panic("ahc_setup_data - Transfer size "
"larger than can device max");
seg.ds_addr = (bus_addr_t)csio->data_ptr;
seg.ds_len = csio->dxfer_len;
ahc_execute_scb(scb, &seg, 1, 0);
}
} else {
struct bus_dma_segment *segs;
if ((ccb_h->flags & CAM_DATA_PHYS) != 0)
panic("ahc_setup_data - Physical segment "
"pointers unsupported");
if ((ccb_h->flags & CAM_SG_LIST_PHYS) == 0)
panic("ahc_setup_data - Virtual segment "
"addresses unsupported");
/* Just use the segments provided */
segs = (struct bus_dma_segment *)csio->data_ptr;
ahc_execute_scb(scb, segs, csio->sglist_cnt, 0);
}
} else {
ahc_execute_scb(scb, NULL, 0, 0);
}
}
static void
ahc_set_recoveryscb(struct ahc_softc *ahc, struct scb *scb) {
if ((scb->flags & SCB_RECOVERY_SCB) == 0) {
struct scb *list_scb;
scb->flags |= SCB_RECOVERY_SCB;
/*
* Take all queued, but not sent SCBs out of the equation.
* Also ensure that no new CCBs are queued to us while we
* try to fix this problem.
*/
if ((scb->io_ctx->ccb_h.status & CAM_RELEASE_SIMQ) == 0) {
xpt_freeze_simq(SCB_GET_SIM(ahc, scb), /*count*/1);
scb->io_ctx->ccb_h.status |= CAM_RELEASE_SIMQ;
}
/*
* Go through all of our pending SCBs and remove
* any scheduled timeouts for them. We will reschedule
* them after we've successfully fixed this problem.
*/
LIST_FOREACH(list_scb, &ahc->pending_scbs, pending_links) {
union ccb *ccb;
ccb = list_scb->io_ctx;
untimeout(ahc_timeout, list_scb, ccb->ccb_h.timeout_ch);
}
}
}
void
ahc_timeout(void *arg)
{
struct scb *scb;
struct ahc_softc *ahc;
long s;
int found;
u_int last_phase;
int target;
int lun;
int i;
char channel;
scb = (struct scb *)arg;
ahc = (struct ahc_softc *)scb->ahc_softc;
ahc_lock(ahc, &s);
ahc_pause_and_flushwork(ahc);
if ((scb->flags & SCB_ACTIVE) == 0) {
/* Previous timeout took care of me already */
printf("%s: Timedout SCB already complete. "
"Interrupts may not be functioning.\n", ahc_name(ahc));
ahc_unpause(ahc);
ahc_unlock(ahc, &s);
return;
}
target = SCB_GET_TARGET(ahc, scb);
channel = SCB_GET_CHANNEL(ahc, scb);
lun = SCB_GET_LUN(scb);
ahc_print_path(ahc, scb);
printf("SCB 0x%x - timed out\n", scb->hscb->tag);
ahc_dump_card_state(ahc);
last_phase = ahc_inb(ahc, LASTPHASE);
if (scb->sg_count > 0) {
for (i = 0; i < scb->sg_count; i++) {
printf("sg[%d] - Addr 0x%x : Length %d\n",
i,
scb->sg_list[i].addr,
scb->sg_list[i].len & AHC_SG_LEN_MASK);
}
}
if (scb->flags & (SCB_DEVICE_RESET|SCB_ABORT)) {
/*
* Been down this road before.
* Do a full bus reset.
*/
bus_reset:
ahc_set_transaction_status(scb, CAM_CMD_TIMEOUT);
found = ahc_reset_channel(ahc, channel, /*Initiate Reset*/TRUE);
printf("%s: Issued Channel %c Bus Reset. "
"%d SCBs aborted\n", ahc_name(ahc), channel, found);
} else {
/*
* If we are a target, transition to bus free and report
* the timeout.
*
* The target/initiator that is holding up the bus may not
* be the same as the one that triggered this timeout
* (different commands have different timeout lengths).
* If the bus is idle and we are actiing as the initiator
* for this request, queue a BDR message to the timed out
* target. Otherwise, if the timed out transaction is
* active:
* Initiator transaction:
* Stuff the message buffer with a BDR message and assert
* ATN in the hopes that the target will let go of the bus
* and go to the mesgout phase. If this fails, we'll
* get another timeout 2 seconds later which will attempt
* a bus reset.
*
* Target transaction:
* Transition to BUS FREE and report the error.
* It's good to be the target!
*/
u_int active_scb_index;
u_int saved_scbptr;
saved_scbptr = ahc_inb(ahc, SCBPTR);
active_scb_index = ahc_inb(ahc, SCB_TAG);
if (last_phase != P_BUSFREE
&& (ahc_inb(ahc, SEQ_FLAGS) & IDENTIFY_SEEN) != 0
&& (active_scb_index < ahc->scb_data->numscbs)) {
struct scb *active_scb;
/*
* If the active SCB is not us, assume that
* the active SCB has a longer timeout than
* the timedout SCB, and wait for the active
* SCB to timeout.
*/
active_scb = ahc_lookup_scb(ahc, active_scb_index);
if (active_scb != scb) {
struct ccb_hdr *ccbh;
uint64_t newtimeout;
ahc_print_path(ahc, scb);
printf("Other SCB Timeout%s",
(scb->flags & SCB_OTHERTCL_TIMEOUT) != 0
? " again\n" : "\n");
scb->flags |= SCB_OTHERTCL_TIMEOUT;
newtimeout =
MAX(active_scb->io_ctx->ccb_h.timeout,
scb->io_ctx->ccb_h.timeout);
newtimeout *= hz;
newtimeout /= 1000;
ccbh = &scb->io_ctx->ccb_h;
scb->io_ctx->ccb_h.timeout_ch =
timeout(ahc_timeout, scb, newtimeout);
ahc_unpause(ahc);
ahc_unlock(ahc, &s);
return;
}
/* It's us */
if ((scb->hscb->control & TARGET_SCB) != 0) {
/*
* Send back any queued up transactions
* and properly record the error condition.
*/
ahc_freeze_devq(ahc, scb);
ahc_set_transaction_status(scb,
CAM_CMD_TIMEOUT);
ahc_freeze_scb(scb);
ahc_done(ahc, scb);
/* Will clear us from the bus */
ahc_restart(ahc);
ahc_unlock(ahc, &s);
return;
}
ahc_set_recoveryscb(ahc, active_scb);
ahc_outb(ahc, MSG_OUT, HOST_MSG);
ahc_outb(ahc, SCSISIGO, last_phase|ATNO);
ahc_print_path(ahc, active_scb);
printf("BDR message in message buffer\n");
active_scb->flags |= SCB_DEVICE_RESET;
active_scb->io_ctx->ccb_h.timeout_ch =
timeout(ahc_timeout, (caddr_t)active_scb, 2 * hz);
ahc_unpause(ahc);
} else {
int disconnected;
/* XXX Shouldn't panic. Just punt instead */
if ((scb->hscb->control & TARGET_SCB) != 0)
panic("Timed-out target SCB but bus idle");
if (last_phase != P_BUSFREE
&& (ahc_inb(ahc, SSTAT0) & TARGET) != 0) {
/* XXX What happened to the SCB? */
/* Hung target selection. Goto busfree */
printf("%s: Hung target selection\n",
ahc_name(ahc));
ahc_restart(ahc);
ahc_unlock(ahc, &s);
return;
}
if (ahc_search_qinfifo(ahc, target, channel, lun,
scb->hscb->tag, ROLE_INITIATOR,
/*status*/0, SEARCH_COUNT) > 0) {
disconnected = FALSE;
} else {
disconnected = TRUE;
}
if (disconnected) {
ahc_set_recoveryscb(ahc, scb);
/*
* Actually re-queue this SCB in an attempt
* to select the device before it reconnects.
* In either case (selection or reselection),
* we will now issue a target reset to the
* timed-out device.
*
* Set the MK_MESSAGE control bit indicating
* that we desire to send a message. We
* also set the disconnected flag since
* in the paging case there is no guarantee
* that our SCB control byte matches the
* version on the card. We don't want the
* sequencer to abort the command thinking
* an unsolicited reselection occurred.
*/
scb->hscb->control |= MK_MESSAGE|DISCONNECTED;
scb->flags |= SCB_DEVICE_RESET;
/*
* Remove any cached copy of this SCB in the
* disconnected list in preparation for the
* queuing of our abort SCB. We use the
* same element in the SCB, SCB_NEXT, for
* both the qinfifo and the disconnected list.
*/
ahc_search_disc_list(ahc, target, channel,
lun, scb->hscb->tag,
/*stop_on_first*/TRUE,
/*remove*/TRUE,
/*save_state*/FALSE);
/*
* In the non-paging case, the sequencer will
* never re-reference the in-core SCB.
* To make sure we are notified during
* reslection, set the MK_MESSAGE flag in
* the card's copy of the SCB.
*/
if ((ahc->flags & AHC_PAGESCBS) == 0) {
ahc_outb(ahc, SCBPTR, scb->hscb->tag);
ahc_outb(ahc, SCB_CONTROL,
ahc_inb(ahc, SCB_CONTROL)
| MK_MESSAGE);
}
/*
* Clear out any entries in the QINFIFO first
* so we are the next SCB for this target
* to run.
*/
ahc_search_qinfifo(ahc,
SCB_GET_TARGET(ahc, scb),
channel, SCB_GET_LUN(scb),
SCB_LIST_NULL,
ROLE_INITIATOR,
CAM_REQUEUE_REQ,
SEARCH_COMPLETE);
ahc_print_path(ahc, scb);
printf("Queuing a BDR SCB\n");
ahc_qinfifo_requeue_tail(ahc, scb);
ahc_outb(ahc, SCBPTR, saved_scbptr);
scb->io_ctx->ccb_h.timeout_ch =
timeout(ahc_timeout, (caddr_t)scb, 2 * hz);
ahc_unpause(ahc);
} else {
/* Go "immediatly" to the bus reset */
/* This shouldn't happen */
ahc_set_recoveryscb(ahc, scb);
ahc_print_path(ahc, scb);
printf("SCB %d: Immediate reset. "
"Flags = 0x%x\n", scb->hscb->tag,
scb->flags);
goto bus_reset;
}
}
}
ahc_unlock(ahc, &s);
}
static void
ahc_abort_ccb(struct ahc_softc *ahc, struct cam_sim *sim, union ccb *ccb)
{
union ccb *abort_ccb;
abort_ccb = ccb->cab.abort_ccb;
switch (abort_ccb->ccb_h.func_code) {
case XPT_ACCEPT_TARGET_IO:
case XPT_IMMED_NOTIFY:
case XPT_CONT_TARGET_IO:
{
struct ahc_tmode_tstate *tstate;
struct ahc_tmode_lstate *lstate;
struct ccb_hdr_slist *list;
cam_status status;
status = ahc_find_tmode_devs(ahc, sim, abort_ccb, &tstate,
&lstate, TRUE);
if (status != CAM_REQ_CMP) {
ccb->ccb_h.status = status;
break;
}
if (abort_ccb->ccb_h.func_code == XPT_ACCEPT_TARGET_IO)
list = &lstate->accept_tios;
else if (abort_ccb->ccb_h.func_code == XPT_IMMED_NOTIFY)
list = &lstate->immed_notifies;
else
list = NULL;
if (list != NULL) {
struct ccb_hdr *curelm;
int found;
curelm = SLIST_FIRST(list);
found = 0;
if (curelm == &abort_ccb->ccb_h) {
found = 1;
SLIST_REMOVE_HEAD(list, sim_links.sle);
} else {
while(curelm != NULL) {
struct ccb_hdr *nextelm;
nextelm =
SLIST_NEXT(curelm, sim_links.sle);
if (nextelm == &abort_ccb->ccb_h) {
found = 1;
SLIST_NEXT(curelm,
sim_links.sle) =
SLIST_NEXT(nextelm,
sim_links.sle);
break;
}
curelm = nextelm;
}
}
if (found) {
abort_ccb->ccb_h.status = CAM_REQ_ABORTED;
xpt_done(abort_ccb);
ccb->ccb_h.status = CAM_REQ_CMP;
} else {
xpt_print_path(abort_ccb->ccb_h.path);
printf("Not found\n");
ccb->ccb_h.status = CAM_PATH_INVALID;
}
break;
}
/* FALLTHROUGH */
}
case XPT_SCSI_IO:
/* XXX Fully implement the hard ones */
ccb->ccb_h.status = CAM_UA_ABORT;
break;
default:
ccb->ccb_h.status = CAM_REQ_INVALID;
break;
}
xpt_done(ccb);
}
void
ahc_send_async(struct ahc_softc *ahc, char channel, u_int target,
u_int lun, ac_code code, void *opt_arg)
{
struct ccb_trans_settings cts;
struct cam_path *path;
void *arg;
int error;
arg = NULL;
error = ahc_create_path(ahc, channel, target, lun, &path);
if (error != CAM_REQ_CMP)
return;
switch (code) {
case AC_TRANSFER_NEG:
{
#ifdef AHC_NEW_TRAN_SETTINGS
struct ccb_trans_settings_scsi *scsi;
cts.type = CTS_TYPE_CURRENT_SETTINGS;
scsi = &cts.proto_specific.scsi;
#else
cts.flags = CCB_TRANS_CURRENT_SETTINGS;
#endif
cts.ccb_h.path = path;
cts.ccb_h.target_id = target;
cts.ccb_h.target_lun = lun;
ahc_get_tran_settings(ahc, channel == 'A' ? ahc->our_id
: ahc->our_id_b,
channel, &cts);
arg = &cts;
#ifdef AHC_NEW_TRAN_SETTINGS
scsi->valid &= ~CTS_SCSI_VALID_TQ;
scsi->flags &= ~CTS_SCSI_FLAGS_TAG_ENB;
#else
cts.valid &= ~CCB_TRANS_TQ_VALID;
cts.flags &= ~CCB_TRANS_TAG_ENB;
#endif
if (opt_arg == NULL)
break;
if (*((ahc_queue_alg *)opt_arg) == AHC_QUEUE_TAGGED)
#ifdef AHC_NEW_TRAN_SETTINGS
scsi->flags |= ~CTS_SCSI_FLAGS_TAG_ENB;
scsi->valid |= CTS_SCSI_VALID_TQ;
#else
cts.flags |= CCB_TRANS_TAG_ENB;
cts.valid |= CCB_TRANS_TQ_VALID;
#endif
break;
}
case AC_SENT_BDR:
case AC_BUS_RESET:
break;
default:
panic("ahc_send_async: Unexpected async event");
}
xpt_async(code, path, arg);
xpt_free_path(path);
}
void
ahc_platform_set_tags(struct ahc_softc *ahc,
struct ahc_devinfo *devinfo, int enable)
{
}
int
ahc_platform_alloc(struct ahc_softc *ahc, void *platform_arg)
{
ahc->platform_data = malloc(sizeof(struct ahc_platform_data), M_DEVBUF,
M_NOWAIT | M_ZERO);
if (ahc->platform_data == NULL)
return (ENOMEM);
return (0);
}
void
ahc_platform_free(struct ahc_softc *ahc)
{
struct ahc_platform_data *pdata;
pdata = ahc->platform_data;
if (pdata != NULL) {
if (pdata->regs != NULL)
bus_release_resource(ahc->dev_softc,
pdata->regs_res_type,
pdata->regs_res_id,
pdata->regs);
if (pdata->irq != NULL)
bus_release_resource(ahc->dev_softc,
pdata->irq_res_type,
0, pdata->irq);
if (pdata->sim_b != NULL) {
xpt_async(AC_LOST_DEVICE, pdata->path_b, NULL);
xpt_free_path(pdata->path_b);
xpt_bus_deregister(cam_sim_path(pdata->sim_b));
cam_sim_free(pdata->sim_b, /*free_devq*/TRUE);
}
if (pdata->sim != NULL) {
xpt_async(AC_LOST_DEVICE, pdata->path, NULL);
xpt_free_path(pdata->path);
xpt_bus_deregister(cam_sim_path(pdata->sim));
cam_sim_free(pdata->sim, /*free_devq*/TRUE);
}
if (pdata->eh != NULL)
EVENTHANDLER_DEREGISTER(shutdown_final, pdata->eh);
free(ahc->platform_data, M_DEVBUF);
}
}
int
ahc_softc_comp(struct ahc_softc *lahc, struct ahc_softc *rahc)
{
/* We don't sort softcs under FreeBSD so report equal always */
return (0);
}
int
ahc_detach(device_t dev)
{
struct ahc_softc *ahc;
u_long s;
device_printf(dev, "detaching device\n");
ahc = device_get_softc(dev);
ahc_lock(ahc, &s);
bus_teardown_intr(dev, ahc->platform_data->irq, ahc->platform_data->ih);
ahc_unlock(ahc, &s);
ahc_free(ahc);
return (0);
}
#if UNUSED
static void
ahc_dump_targcmd(struct target_cmd *cmd)
{
uint8_t *byte;
uint8_t *last_byte;
int i;
byte = &cmd->initiator_channel;
/* Debugging info for received commands */
last_byte = &cmd[1].initiator_channel;
i = 0;
while (byte < last_byte) {
if (i == 0)
printf("\t");
printf("%#x", *byte++);
i++;
if (i == 8) {
printf("\n");
i = 0;
} else {
printf(", ");
}
}
}
#endif
static int
ahc_modevent(module_t mod, int type, void *data)
{
/* XXX Deal with busy status on unload. */
return 0;
}
static moduledata_t ahc_mod = {
"ahc",
ahc_modevent,
NULL
};
DECLARE_MODULE(ahc, ahc_mod, SI_SUB_DRIVERS, SI_ORDER_MIDDLE);
MODULE_DEPEND(ahc, cam, 1, 1, 1);
MODULE_VERSION(ahc, 1);
Reference in New Issue View Git Blame Copy Permalink