1d88dfe265
o ToPIC is happy with two cards now, even when the two cards are modems. o Fix (all?) hangs on boot when power is applied to the card. I suspect that this will make the Ricoh bridges happier and also make a lot of VAIO owners happy (confirm to me in private email please :-). o All Cardbus bridges should now support 3.3V, X.XV and Y.YV cards, to the extent that the underlying hardware supports such cards. (X.X and Y.Y haven't been assigned values yet :-). o Better 3.3V support for Ricoh ISA bridges. How: o Don't mess with the power register when scanning the cards. It is unnecessary and causes BADVcc conditions on many chipsets. These in turn can cause an interrupt storm. o Make pcic_disable reset the slot's voltage. o Move initializing voltage for the slot until after it has been disabled. o Fix a lot of issues with the pcic_cardbus_power routine. We now properly enable the card and take it out of reset after a power change. o When detecting the card's voltage, if we're in a BadVcc state, direct the bridge to rescan the card for what it supports. (we might need to in the future set the power register to 0 before doing this). o Don't preserve CLKSTOP. need to revisit this. o Better support for Ricoh ISA bridges for 3.3V cards. o Don't write to PCIC_POWER directly as offten, but instead go through the pcic_power interface. o All cardbus bridges now default to use cardbus power control. o Add misc register definitions. o remove some (now) bogus comments. Extra Special Thanks To: Scott Lamber for his kind and generous loan of a Toshiba laptop with a ToPIC 100 in it for my use.
316 lines
13 KiB
C
316 lines
13 KiB
C
/*
|
|
* i82365.h - Definitions for Intel 82365 PCIC
|
|
* PCMCIA Card Interface Controller
|
|
*
|
|
* originally by Barry Jaspan; hacked over by Keith Moore
|
|
* hacked to unrecognisability by Andrew McRae (andrew@mega.com.au)
|
|
*
|
|
* Updated 3/3/95 to include Cirrus Logic stuff.
|
|
*-------------------------------------------------------------------------
|
|
*
|
|
* Copyright (c) 2001 M. Warner Losh. All rights reserved.
|
|
* Copyright (c) 1995 Andrew McRae. All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
* 3. The name of the author may not be used to endorse or promote products
|
|
* derived from this software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
|
|
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
|
|
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
|
|
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
|
|
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
|
|
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
|
|
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
|
|
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
|
|
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
*
|
|
* $FreeBSD$
|
|
*/
|
|
|
|
#define PCIC_I82365 0 /* Intel i82365SL-A/B or clone */
|
|
#define PCIC_IBM 1 /* IBM clone */
|
|
#define PCIC_VLSI 2 /* VLSI chip */
|
|
#define PCIC_PD6722 3 /* Cirrus logic PD6722 */
|
|
#define PCIC_PD6710 4 /* Cirrus logic PD6710 */
|
|
#define PCIC_VG365 5 /* Vadem 365 */
|
|
#define PCIC_VG465 6 /* Vadem 465 */
|
|
#define PCIC_VG468 7 /* Vadem 468 */
|
|
#define PCIC_VG469 8 /* Vadem 469 */
|
|
#define PCIC_RF5C296 9 /* Ricoh RF5C296 */
|
|
#define PCIC_RF5C396 10 /* Ricoh RF5C396 */
|
|
#define PCIC_IBM_KING 11 /* IBM KING PCMCIA Controller */
|
|
#define PCIC_I82365SL_DF 12 /* Intel i82365sl-DF step */
|
|
#define PCIC_PD6729 13 /* Cirrus Logic PD6729 */
|
|
#define PCIC_PD673X 14 /* Cirrus Logic PD673x */
|
|
|
|
/*
|
|
* Address of the controllers. Each controller can manage
|
|
* two PCMCIA slots. Up to 8 slots are supported in total.
|
|
* The PCIC controller is accessed via an index port and a
|
|
* data port. The index port has the 8 bit address of the
|
|
* register accessed via the data port. How I long for
|
|
* real memory mapped I/O!
|
|
* The top two bits of the index address are used to
|
|
* identify the port number, and the lower 6 bits
|
|
* select one of the 64 possible data registers.
|
|
*/
|
|
#define PCIC_INDEX 0 /* Index register */
|
|
#define PCIC_DATA 1 /* Data register */
|
|
#define PCIC_NPORT 2 /* Number of ports */
|
|
#define PCIC_PORT_0 0x3e0 /* index reg, chips 0 and 1 */
|
|
|
|
/*
|
|
* Register index addresses.
|
|
*/
|
|
#define PCIC_ID_REV 0x00 /* Identification and Revision */
|
|
#define PCIC_STATUS 0x01 /* Interface Status */
|
|
#define PCIC_POWER 0x02 /* Power and RESETDRV control */
|
|
#define PCIC_INT_GEN 0x03 /* Interrupt and General Control */
|
|
#define PCIC_STAT_CHG 0x04 /* Card Status Change */
|
|
#define PCIC_STAT_INT 0x05 /* Card Status Change Interrupt Config */
|
|
#define PCIC_ADDRWINE 0x06 /* Address Window Enable */
|
|
#define PCIC_IOCTL 0x07 /* I/O Control */
|
|
#define PCIC_IO0 0x08 /* I/O Address 0 */
|
|
#define PCIC_IO1 0x0c /* I/O Address 1 */
|
|
#define PCIC_MEMBASE 0x10 /* Base of memory window registers */
|
|
#define PCIC_CDGC 0x16 /* Card Detect and General Control */
|
|
#define PCIC_MISC1 0x16 /* PD67xx: Misc control register 1 per slot */
|
|
#define PCIC_GLO_CTRL 0x1e /* Global Control Register */
|
|
#define PCIC_MISC2 0x1e /* PD67xx: Misc control register 2 per chip */
|
|
#define PCIC_CLCHIP 0x1f /* PD67xx: Chip I/D */
|
|
#define PCIC_EXT_IND 0x2e /* PD67xx: Extended Index */
|
|
#define PCIC_EXTENDED 0x2f /* PD67xx: Extended register */
|
|
#define PCIC_CVSR 0x2f /* Vadem: Voltage select register */
|
|
#define PCIC_RICOH_MCR2 0x2f /* Ricoh: Mode Control Register 2 */
|
|
|
|
#define PCIC_VMISC 0x3a /* Vadem: Misc control register */
|
|
#define PCIC_RICOH_ID 0x3a /* Ricoh: ID register */
|
|
|
|
#define PCIC_TOPIC_FCR 0x3e /* Toshiba ToPIC: Function Control Register */
|
|
|
|
#define PCIC_TIME_SETUP0 0x3a
|
|
#define PCIC_TIME_CMD0 0x3b
|
|
#define PCIC_TIME_RECOV0 0x3c
|
|
#define PCIC_TIME_SETUP1 0x3d
|
|
#define PCIC_TIME_CMD1 0x3e
|
|
#define PCIC_TIME_RECOV1 0x3f
|
|
|
|
#define PCIC_SLOT_SIZE 0x40 /* Size of register set for one slot */
|
|
|
|
/* Now register bits, ordered by reg # */
|
|
|
|
/* For Identification and Revision (PCIC_ID_REV) */
|
|
#define PCIC_INTEL0 0x82 /* Intel 82365SL Rev. 0; Both Memory and I/O */
|
|
#define PCIC_INTEL1 0x83 /* Intel 82365SL Rev. 1; Both Memory and I/O */
|
|
#define PCIC_INTEL2 0x84 /* Intel 82365SL step D */
|
|
#define PCIC_VLSI82C146 0x84 /* VLSI 82C146 */
|
|
#define PCIC_IBM1 0x88 /* IBM PCIC clone; Both Memory and I/O */
|
|
#define PCIC_IBM2 0x89 /* IBM PCIC clone; Both Memory and I/O */
|
|
#define PCIC_IBM3 0x8a /* IBM KING PCIC clone; Both Memory and I/O */
|
|
|
|
/* For Interface Status register (PCIC_STATUS) */
|
|
#define PCIC_VPPV 0x80 /* Vpp_valid or reserved*/
|
|
#define PCIC_RICOH_5VCARD 0x80 /* 5V card detected */
|
|
#define PCIC_POW 0x40 /* PC Card power active */
|
|
#define PCIC_READY 0x20 /* Ready/~Busy */
|
|
#define PCIC_MWP 0x10 /* Memory Write Protect */
|
|
#define PCIC_CD 0x0C /* Both card detect bits */
|
|
#define PCIC_BVD 0x03 /* Both Battery Voltage Detect bits */
|
|
|
|
/* For the Power and RESETDRV register (PCIC_POWER) */
|
|
#define PCIC_OUTENA 0x80 /* Output Enable */
|
|
#define PCIC_DISRST 0x40 /* Disable RESETDRV */
|
|
#define PCIC_APSENA 0x20 /* Auto Pwer Switch Enable */
|
|
#define PCIC_PCPWRE 0x10 /* PC Card Power Enable */
|
|
#define PCIC_VCC 0x18 /* Vcc control bits */
|
|
#define PCIC_VCC_5V 0x10 /* 5 volts */
|
|
#define PCIC_VCC_ON 0x10 /* Turn on VCC on some chips. */
|
|
#define PCIC_VCC_3V 0x18 /* 3 volts */
|
|
#define PCIC_VCC_5V_KING 0x14 /* 5 volts for KING PCIC */
|
|
#define PCIC_VPP 0x03 /* Vpp control bits */
|
|
#define PCIC_VPP_5V 0x01 /* 5 volts */
|
|
#define PCIC_VPP_12V 0x02 /* 12 volts */
|
|
|
|
/* For the Interrupt and General Control register (PCIC_INT_GEN) */
|
|
#define PCIC_CARDRESET 0x40 /* Card reset 0 = Reset, 1 = Normal */
|
|
#define PCIC_CARDTYPE 0x20 /* Card Type 0 = memory, 1 = I/O */
|
|
#define PCIC_IOCARD 0x20
|
|
#define PCIC_MEMCARD 0x00
|
|
#define PCIC_INTR_ENA 0x10 /* PCI CSC Interrupt enable */
|
|
|
|
/* For the Card Status Change register (PCIC_STAT_CHG) */
|
|
#define PCIC_CDTCH 0x08 /* Card Detect Change */
|
|
#define PCIC_RDYCH 0x04 /* Ready Change */
|
|
#define PCIC_BATWRN 0x02 /* Battery Warning */
|
|
#define PCIC_BATDED 0x01 /* Battery Dead */
|
|
|
|
/* For the Card status change interrupt PCIC_STAT_INT */
|
|
#define PCIC_CSCSELECT 0xf0 /* CSCSELECT */
|
|
#define PCIC_SI_IRQ_SHIFT 4
|
|
#define PCIC_CDEN 0x8
|
|
#define PCIC_READYEN 0x4
|
|
#define PCIC_BATWARNEN 0x2
|
|
#define PCIC_BATDEADEN 0x1
|
|
|
|
/*
|
|
* For the Address Window Enable Register (PCIC_ADDRWINE)
|
|
* The lower 6 bits contain enable bits for the memory
|
|
* windows (LSB = memory window 0).
|
|
*/
|
|
#define PCIC_MEMCS16 0x20 /* ~MEMCS16 Decode A23-A12 */
|
|
#define PCIC_IO0_EN 0x40 /* I/O Window 0 Enable */
|
|
#define PCIC_IO1_EN 0x80 /* I/O Window 1 Enable */
|
|
|
|
/*
|
|
* For the I/O Control Register (PCIC_IOCTL)
|
|
* The lower nybble is the flags for I/O window 0
|
|
* The upper nybble is the flags for I/O window 1
|
|
*/
|
|
#define PCIC_IO_16BIT 0x01 /* I/O to this segment is 16 bit */
|
|
#define PCIC_IO_CS16 0x02 /* I/O cs16 source is the card */
|
|
#define PCIC_IO_0WS 0x04 /* zero wait states added on 8 bit cycles */
|
|
#define PCIC_IO_WS 0x08 /* Wait states added for 16 bit cycles */
|
|
|
|
/*
|
|
* The memory window registers contain the start and end
|
|
* physical host address that the PCIC maps to the card,
|
|
* and an offset calculated from the card memory address.
|
|
* All values are shifted down 12 bits, so allocation is
|
|
* done in 4Kb blocks. Only 12 bits of each value is
|
|
* stored, limiting the range to the ISA address size of
|
|
* 24 bits. The upper 4 bits of the most significant byte
|
|
* within the values are used for various flags.
|
|
*
|
|
* The layout is:
|
|
*
|
|
* base+0 : lower 8 bits of system memory start address
|
|
* base+1 : upper 4 bits of system memory start address + flags
|
|
* base+2 : lower 8 bits of system memory end address
|
|
* base+3 : upper 4 bits of system memory end address + flags
|
|
* base+4 : lower 8 bits of offset to card address
|
|
* base+5 : upper 4 bits of offset to card address + flags
|
|
*
|
|
* The following two bytes are reserved for other use.
|
|
*/
|
|
#define PCIC_MEMSIZE 8
|
|
/*
|
|
* Flags for system memory start address upper byte
|
|
*/
|
|
#define PCIC_ZEROWS 0x40 /* Zero wait states */
|
|
#define PCIC_DATA16 0x80 /* Data width is 16 bits */
|
|
|
|
/*
|
|
* Flags for system memory end address upper byte
|
|
*/
|
|
#define PCIC_MW0 0x40 /* Wait state bit 0 */
|
|
#define PCIC_MW1 0x80 /* Wait state bit 1 */
|
|
|
|
/*
|
|
* Flags for card offset upper byte
|
|
*/
|
|
#define PCIC_REG 0x40 /* Attribute/Common select (why called Reg?) */
|
|
#define PCIC_WP 0x80 /* Write-protect this window */
|
|
|
|
/* For Card Detect and General Control register (PCIC_CDGC) */
|
|
#define PCIC_16_DL_INH 0x01 /* 16-bit memory delay inhibit */
|
|
#define PCIC_CNFG_RST_EN 0x02 /* configuration reset enable */
|
|
#define PCIC_GPI_EN 0x04 /* GPI Enable */
|
|
#define PCIC_GPI_TRANS 0x08 /* GPI Transition Control */
|
|
#define PCIC_CDRES_EN 0x10 /* card detect resume enable */
|
|
#define PCIC_SW_CD_INT 0x20 /* s/w card detect interrupt */
|
|
#define PCIC_VS1STAT 0x40 /* 0 VS1# low, 1 VS1# high */
|
|
#define PCIC_VS2STAT 0x80 /* 0 VS2# low, 1 VS2# high */
|
|
|
|
/* CL-PD67[12]x: For 3.3V cards, etc. (PCIC_MISC1) */
|
|
#define PCIC_MISC1_5V_DETECT 0x01 /* PD6710 only */
|
|
#define PCIC_MISC1_VCC_33 0x02 /* Set Vcc is 3.3V, else 5.0V */
|
|
#define PCIC_MISC1_PMINT 0x04 /* Pulse management intr */
|
|
#define PCIC_MISC1_PCINT 0x08 /* Pulse card interrupt */
|
|
#define PCIC_MISC1_SPEAKER 0x10 /* Enable speaker */
|
|
#define PCIC_MISC1_INPACK 0x80 /* INPACK throttles data */
|
|
|
|
/* i82365B and newer (!PD67xx) Global Control register (PCIC_GLO_CTRL) */
|
|
#define PCIC_PWR_DOWN 0x01 /* power down */
|
|
#define PCIC_LVL_MODE 0x02 /* level mode interrupt enable */
|
|
#define PCIC_WB_CSCINT 0x04 /* explicit write-back csc intr */
|
|
/* Rev B only */
|
|
#define PCIC_IRQ0_LEVEL 0x08 /* irq 14 pulse mode enable */
|
|
#define PCIC_IRQ1_LEVEL 0x10
|
|
|
|
/* CL-PD67[12]x: For Misc. Control Register 2 (PCIC_MISC2) */
|
|
#define PCIC_LPDM_EN 0x02 /* Cirrus PD672x: low power dynamic mode */
|
|
|
|
/* CL-PD67[12]x: Chip info (PCIC_CLCHIP) */
|
|
#define PCIC_CLC_TOGGLE 0xc0 /* These bits toggle 1 -> 0 */
|
|
#define PCIC_CLC_DUAL 0x20 /* Single/dual socket version */
|
|
|
|
/* Cirrus Logic: Extended Registers (PCIC_EXT_IND) */
|
|
#define PCIC_EXT_DATA 0x0a /* External Data */
|
|
|
|
/* EXT_DATA */
|
|
#define PCIC_VS1A 0x01
|
|
#define PCIC_VS2A 0x02
|
|
#define PCIC_VS1B 0x04
|
|
#define PCIC_VS2B 0x08
|
|
|
|
/* Vadem: Card Voltage Select register (PCIC_CVSR) */
|
|
#define PCIC_CVSR_VS 0x03 /* Voltage select */
|
|
#define PCIC_CVSR_VS_5 0x00 /* 5.0 V */
|
|
#define PCIC_CVSR_VS_33a 0x01 /* alt 3.3V */
|
|
#define PCIC_CVSR_VS_XX 0x02 /* X.XV when available */
|
|
#define PCIC_CVSR_VS_33 0x03 /* 3.3V */
|
|
|
|
/* Ricoh: Misc Control Register 2 (PCIC_RICOH_MCR2) */
|
|
#define PCIC_MCR2_VCC_33 0x01 /* 3.3V */
|
|
|
|
/* Vadem: misc register (PCIC_VMISC) */
|
|
#define PCIC_VADEMREV 0x40
|
|
|
|
/* Ricoh: ID register values (PCIC_RICOH_ID) */
|
|
#define PCIC_RID_296 0x32
|
|
#define PCIC_RID_396 0xb2
|
|
|
|
/* Toshiba ToPIC: Function Control Register */
|
|
#define PCIC_FCR_3V_EN 0x01 /* Enable 3V cards */
|
|
#define PCIC_FCR_VS_EN 0x02 /* Voltage Sense enable */
|
|
|
|
/*
|
|
* Mask of allowable interrupts.
|
|
*
|
|
* For IBM-AT machines, irqs 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 are
|
|
* allowed. Nearly all IBM-AT machines with pcic cards or bridges
|
|
* wire these interrupts (or a subset thereof) to the corresponding
|
|
* pins on the ISA bus. Some older laptops are reported to not route
|
|
* all the interrupt pins to the bus because the designers knew that
|
|
* some would conflict with builtin devices.
|
|
*
|
|
* For NEC PC98 machines, irq 3, 5, 6, 9, 10, 11, 12, 13 are allowed.
|
|
* These correspond to the C-BUS signals INT 0, 1, 2, 3, 41, 42, 5, 6
|
|
* respectively. This is with the desktop C-BUS addin card.
|
|
*
|
|
* Hiroshi TSUKADA-san writes in FreeBSD98-testers that cbus IRQ
|
|
* 6 is routed to the IRQ 7 pin of the pcic in pc98 cbus based
|
|
* cards. I do not know how pc98 laptop models are wired.
|
|
*/
|
|
#ifdef PC98
|
|
#define PCIC_INT_MASK_ALLOWED 0x3E68 /* PC98 */
|
|
#else
|
|
#define PCIC_INT_MASK_ALLOWED 0xDEB8 /* AT */
|
|
#endif
|
|
|
|
#define PCIC_IO_WIN 2
|
|
#define PCIC_MEM_WIN 5
|
|
|
|
#define PCIC_CARD_SLOTS 4
|
|
#define PCIC_MAX_CARDS 2
|
|
#define PCIC_MAX_SLOTS (PCIC_MAX_CARDS * PCIC_CARD_SLOTS)
|