126 lines
4.6 KiB
C
126 lines
4.6 KiB
C
/*-
|
|
* SPDX-License-Identifier: BSD-2-Clause
|
|
*
|
|
* Copyright (c) 2017 Ian Lepore <ian@freebsd.org>
|
|
*
|
|
* Development sponsored by Microsemi, Inc.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
|
|
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGE.
|
|
*/
|
|
|
|
#include <sys/cdefs.h>
|
|
__FBSDID("$FreeBSD$");
|
|
|
|
/*
|
|
* Helper code to recover a hung i2c bus by bit-banging a recovery sequence.
|
|
*
|
|
* An i2c bus can be hung by a slave driving the clock (rare) or data lines low.
|
|
* The most common cause is a partially-completed transaction such as rebooting
|
|
* while a slave is sending a byte of data. Because i2c allows the clock to
|
|
* freeze for any amount of time, the slave device will continue driving the
|
|
* data line until power is removed, or the clock cycles enough times to
|
|
* complete the current byte. After completing any partial byte, a START/STOP
|
|
* sequence resets the slave and the bus is recovered.
|
|
*
|
|
* Any i2c driver which is able to manually set the level of the clock and data
|
|
* lines can use this common code for bus recovery. On many SOCs that have
|
|
* embedded i2c controllers, the i2c pins can be temporarily reassigned as gpio
|
|
* pins to do the bus recovery, then can be assigned back to the i2c hardware.
|
|
*/
|
|
|
|
#include "opt_platform.h"
|
|
|
|
#include <sys/param.h>
|
|
#include <sys/systm.h>
|
|
#include <sys/bus.h>
|
|
|
|
#include <dev/iicbus/iic_recover_bus.h>
|
|
#include <dev/iicbus/iiconf.h>
|
|
|
|
int
|
|
iic_recover_bus(struct iicrb_pin_access *pins)
|
|
{
|
|
const u_int timeout_us = 40000;
|
|
const u_int delay_us = 500;
|
|
int i;
|
|
|
|
/*
|
|
* Start with clock and data high.
|
|
*/
|
|
pins->setsda(pins->ctx, 1);
|
|
pins->setscl(pins->ctx, 1);
|
|
|
|
/*
|
|
* At this point, SCL should be high. If it's not, some slave on the
|
|
* bus is doing clock-stretching and we should wait a while. If that
|
|
* slave is completely locked up there may be no way to recover at all.
|
|
* We wait up to 40 milliseconds, a seriously pessimistic time (even a
|
|
* cheap eeprom has a max post-write delay of only 10ms), and also long
|
|
* enough to allow SMB slaves to timeout normally after 35ms.
|
|
*/
|
|
for (i = 0; i < timeout_us; i += delay_us) {
|
|
if (pins->getscl(pins->ctx))
|
|
break;
|
|
DELAY(delay_us);
|
|
}
|
|
if (i >= timeout_us)
|
|
return (IIC_EBUSERR);
|
|
|
|
/*
|
|
* At this point we should be able to control the clock line. Some
|
|
* slave may be part way through a byte transfer, and could be holding
|
|
* the data line low waiting for more clock pulses to finish the byte.
|
|
* Cycle the clock until we see the data line go high, but only up to 9
|
|
* times because if it's not free after 9 clocks we're never going to
|
|
* win this battle. We do 9 max because that's a byte plus an ack/nack
|
|
* bit, after which the slave must not be driving the data line anymore.
|
|
*/
|
|
for (i = 0; ; ++i) {
|
|
if (pins->getsda(pins->ctx))
|
|
break;
|
|
if (i == 9)
|
|
return (IIC_EBUSERR);
|
|
pins->setscl(pins->ctx, 0);
|
|
DELAY(5);
|
|
pins->setscl(pins->ctx, 1);
|
|
DELAY(5);
|
|
}
|
|
|
|
/*
|
|
* At this point we should be in control of both the clock and data
|
|
* lines, and both lines should be high. To complete the reset of a
|
|
* slave that was part way through a transaction, we need to do a
|
|
* START/STOP sequence, which leaves both lines high at the end.
|
|
* - START: SDA transitions high->low while SCL remains high.
|
|
* - STOP: SDA transitions low->high while SCL remains high.
|
|
* Note that even though the clock line remains high, we transition the
|
|
* data line no faster than it would change state with a 100khz clock.
|
|
*/
|
|
pins->setsda(pins->ctx, 0);
|
|
DELAY(5);
|
|
pins->setsda(pins->ctx, 1);
|
|
DELAY(5);
|
|
|
|
return (0);
|
|
}
|
|
|