9cde3e4074
have other media to test against, I've left that media reporting unchanged. o Enable the TX_PLL when we enable TX. This is harmless on most cards, but required to get the 3c1 CF card working. Power savings could be had by managing this better, but for now it gets my card working.
435 lines
14 KiB
C
435 lines
14 KiB
C
/*-
|
|
* Copyright (c) 1993 Herb Peyerl (hpeyerl@novatel.ca) All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions are
|
|
* met: 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer. 2. The name
|
|
* of the author may not be used to endorse or promote products derived from
|
|
* this software without specific prior written permission
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR IMPLIED
|
|
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
|
|
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
|
|
* EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
|
|
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
|
|
* TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
|
|
* PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
|
|
* LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
|
|
* NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
|
|
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
*
|
|
* $FreeBSD$
|
|
*/
|
|
|
|
/*
|
|
* DELAY_MULTIPLE: How much to boost "base" delays, except
|
|
* for the inter-bit delays in get_eeprom_data. A cyrix Media GX needed this.
|
|
*/
|
|
#define DELAY_MULTIPLE 10
|
|
#define BIT_DELAY_MULTIPLE 10
|
|
|
|
/*
|
|
* Some global constants
|
|
*/
|
|
#define TX_INIT_RATE 16
|
|
#define TX_INIT_MAX_RATE 64
|
|
#define RX_INIT_LATENCY 64
|
|
#define RX_INIT_EARLY_THRESH 208/* not less than MINCLSIZE */
|
|
#define RX_NEXT_EARLY_THRESH 500
|
|
|
|
#define EEPROMSIZE 0x40
|
|
#define MAX_EEPROMBUSY 1000
|
|
#define EP_LAST_TAG 0xd7
|
|
#define EP_MAX_BOARDS 16
|
|
#define EP_IOSIZE 16 /* 16 bytes of I/O space used. */
|
|
|
|
/*
|
|
* Commands to read/write EEPROM trough EEPROM command register (Window 0,
|
|
* Offset 0xa)
|
|
*/
|
|
#define EEPROM_CMD_RD 0x0080 /* Read: Address required (5 bits) */
|
|
#define EEPROM_CMD_WR 0x0040 /* Write: Address required (5 bits) */
|
|
#define EEPROM_CMD_ERASE 0x00c0 /* Erase: Address required (5 bits) */
|
|
#define EEPROM_CMD_EWEN 0x0030 /* Erase/Write Enable: No data required */
|
|
|
|
#define EEPROM_BUSY (1<<15)
|
|
#define EEPROM_TST_MODE (1<<14)
|
|
|
|
/*
|
|
* Some short functions, worth to let them be a macro
|
|
*/
|
|
#define is_eeprom_busy(sc) (CSR_READ_2(sc, EP_W0_EEPROM_COMMAND)&EEPROM_BUSY)
|
|
#define GO_WINDOW(sc, x) CSR_WRITE_2(sc, EP_COMMAND, WINDOW_SELECT|(x))
|
|
|
|
/**************************************************************************
|
|
* *
|
|
* These define the EEPROM data structure. They are used in the probe
|
|
* function to verify the existence of the adapter after having sent
|
|
* the ID_Sequence.
|
|
*
|
|
**************************************************************************/
|
|
|
|
#define EEPROM_NODE_ADDR_0 0x0 /* Word */
|
|
#define EEPROM_NODE_ADDR_1 0x1 /* Word */
|
|
#define EEPROM_NODE_ADDR_2 0x2 /* Word */
|
|
#define EEPROM_PROD_ID 0x3 /* 0x9[0-f]50 */
|
|
#define EEPROM_MFG_DATE 0x4 /* Manufacturing date */
|
|
#define EEPROM_MFG_DIVSION 0x5 /* Manufacturing division */
|
|
#define EEPROM_MFG_PRODUCT 0x6 /* Product code */
|
|
#define EEPROM_MFG_ID 0x7 /* 0x6d50 */
|
|
#define EEPROM_ADDR_CFG 0x8 /* Base addr */
|
|
#define ADDR_CFG_EISA 0x1f
|
|
#define ADDR_CFG_MASK 0x1f
|
|
#define EEPROM_RESOURCE_CFG 0x9 /* IRQ. Bits 12-15 */
|
|
#define EEPROM_OEM_ADDR0 0xa
|
|
#define EEPROM_OEM_ADDR1 0xb
|
|
#define EEPROM_OEM_ADDR2 0xc
|
|
#define EEPROM_SOFTINFO 0xd
|
|
#define EEPROM_COMPAT 0xe
|
|
#define EEPROM_SOFTINFO2 0xf
|
|
#define EEPROM_CAP 0x10
|
|
#define CAP_ISA 0x2083
|
|
#define CAP_PCMCIA 0x2082
|
|
#define EEPROM_INT_CONFIG_0 0x12
|
|
#define EEPROM_INT_CONFIG_1 0x13
|
|
/* RAM Partition TX FIFO/RX FIFO */
|
|
#define ICW1_RAM_PART_MASK 0x03
|
|
#define ICW1_RAM_PART_35 0x00 /* 2:5 (only legal if RAM size == 000b
|
|
* default power-up/reset */
|
|
#define ICW1_RAM_PART_13 0x01 /* 1:3 (only legal if RAM size ==
|
|
* 000b) */
|
|
#define ICW1_RAM_PART_11 0x10 /* 1:1 */
|
|
#define ICW1_RAM_PART_RESV 0x11 /* Reserved */
|
|
/* ISA Adapter Selection */
|
|
#define ICW1_IAS_MASK 0x0c
|
|
#define ICW1_IAS_DIS 0x00 /* Both mechanisms disabled (default) */
|
|
#define ICW1_IAS_ISA 0x04 /* ISA contention only */
|
|
#define ICW1_IAS_PNP 0x08 /* ISA Plug and Play only */
|
|
#define ICW1_IAS_BOTH 0x0c /* Both mechanisms enabled */
|
|
|
|
#define EEPROM_CHECKSUM_EL3 0x17
|
|
|
|
/**************************************************************************
|
|
* *
|
|
* These are the registers for the 3Com 3c509 and their bit patterns when *
|
|
* applicable. They have been taken out the the "EtherLink III Parallel *
|
|
* Tasking EISA and ISA Technical Reference" "Beta Draft 10/30/92" manual *
|
|
* from 3com. *
|
|
* *
|
|
**************************************************************************/
|
|
|
|
#define EP_COMMAND 0x0e /* Write. BASE+0x0e is always a
|
|
* command reg. */
|
|
#define EP_STATUS 0x0e /* Read. BASE+0x0e is always status
|
|
* reg. */
|
|
#define EP_WINDOW 0x0f /* Read. BASE+0x0f is always window
|
|
* reg. */
|
|
/*
|
|
* Window 0 registers. Setup.
|
|
*/
|
|
/* Write */
|
|
#define EP_W0_EEPROM_DATA 0x0c
|
|
#define EP_W0_EEPROM_COMMAND 0x0a
|
|
#define EP_W0_RESOURCE_CFG 0x08
|
|
#define EP_W0_ADDRESS_CFG 0x06
|
|
#define EP_W0_CONFIG_CTRL 0x04
|
|
/* Read */
|
|
#define EP_W0_PRODUCT_ID 0x02
|
|
#define EP_W0_MFG_ID 0x00
|
|
|
|
/*
|
|
* Window 1 registers. Operating Set.
|
|
*/
|
|
/* Write */
|
|
#define EP_W1_TX_PIO_WR_2 0x02
|
|
#define EP_W1_TX_PIO_WR_1 0x00
|
|
/* Read */
|
|
#define EP_W1_FREE_TX 0x0c
|
|
#define EP_W1_TX_STATUS 0x0b /* byte */
|
|
#define EP_W1_TIMER 0x0a /* byte */
|
|
#define EP_W1_RX_STATUS 0x08
|
|
#define EP_W1_RX_PIO_RD_2 0x02
|
|
#define EP_W1_RX_PIO_RD_1 0x00
|
|
|
|
/*
|
|
* Window 2 registers. Station Address Setup/Read
|
|
*/
|
|
/* Read/Write */
|
|
#define EP_W2_PHY_MGMT 0x0c
|
|
#define EP_W2_ALT_EEPROM 0x0a
|
|
#define EP_W2_ADDR_5 0x05
|
|
#define EP_W2_ADDR_4 0x04
|
|
#define EP_W2_ADDR_3 0x03
|
|
#define EP_W2_ADDR_2 0x02
|
|
#define EP_W2_ADDR_1 0x01
|
|
#define EP_W2_ADDR_0 0x00
|
|
|
|
/*
|
|
* Window 3 registers. FIFO Management.
|
|
*/
|
|
/* Read */
|
|
#define EP_W3_FREE_TX 0x0c
|
|
#define EP_W3_FREE_RX 0x0a
|
|
#define EP_W3_OPTIONS 0x08
|
|
|
|
/*
|
|
* Window 4 registers. Diagnostics.
|
|
*/
|
|
/* Read/Write */
|
|
#define EP_W4_MEDIA_TYPE 0x0a
|
|
#define EP_W4_CTRLR_STATUS 0x08
|
|
#define EP_W4_NET_DIAG 0x06
|
|
#define EP_W4_FIFO_DIAG 0x04
|
|
#define EP_W4_HOST_DIAG 0x02
|
|
#define EP_W4_TX_DIAG 0x00
|
|
|
|
/*
|
|
* Window 5 Registers. Results and Internal status.
|
|
*/
|
|
/* Read */
|
|
#define EP_W5_READ_0_MASK 0x0c
|
|
#define EP_W5_INTR_MASK 0x0a
|
|
#define EP_W5_RX_FILTER 0x08
|
|
#define EP_W5_RX_EARLY_THRESH 0x06
|
|
#define EP_W5_TX_AVAIL_THRESH 0x02
|
|
#define EP_W5_TX_START_THRESH 0x00
|
|
|
|
/*
|
|
* Window 6 registers. Statistics.
|
|
*/
|
|
/* Read/Write */
|
|
#define TX_TOTAL_OK 0x0c
|
|
#define RX_TOTAL_OK 0x0a
|
|
#define TX_DEFERRALS 0x08
|
|
#define RX_FRAMES_OK 0x07
|
|
#define TX_FRAMES_OK 0x06
|
|
#define RX_OVERRUNS 0x05
|
|
#define TX_COLLISIONS 0x04
|
|
#define TX_AFTER_1_COLLISION 0x03
|
|
#define TX_AFTER_X_COLLISIONS 0x02
|
|
#define TX_NO_SQE 0x01
|
|
#define TX_CD_LOST 0x00
|
|
|
|
/****************************************
|
|
*
|
|
* Register definitions.
|
|
*
|
|
****************************************/
|
|
|
|
/*
|
|
* Command parameter that disables threshold interrupts
|
|
* PIO (3c509) cards use 2044. The fifo word-oriented and 2044--2047 work.
|
|
* "busmastering" cards need 8188.
|
|
* The implicit two-bit upshift done by busmastering cards means
|
|
* a value of 2047 disables threshold interrupts on both.
|
|
*/
|
|
#define EP_THRESH_DISABLE 2047
|
|
|
|
/*
|
|
* Command register. All windows.
|
|
*
|
|
* 16 bit register.
|
|
* 15-11: 5-bit code for command to be executed.
|
|
* 10-0: 11-bit arg if any. For commands with no args;
|
|
* this can be set to anything.
|
|
*/
|
|
#define GLOBAL_RESET (u_short) 0x0000 /* Wait at least 1ms
|
|
* after issuing */
|
|
#define WINDOW_SELECT (u_short) (0x1<<11)
|
|
#define START_TRANSCEIVER (u_short) (0x2<<11) /* Read ADDR_CFG reg to
|
|
* determine whether
|
|
* this is needed. If
|
|
* so; wait 800 uSec
|
|
* before using trans-
|
|
* ceiver. */
|
|
#define RX_DISABLE (u_short) (0x3<<11) /* state disabled on
|
|
* power-up */
|
|
#define RX_ENABLE (u_short) (0x4<<11)
|
|
#define RX_RESET (u_short) (0x5<<11)
|
|
#define RX_DISCARD_TOP_PACK (u_short) (0x8<<11)
|
|
#define TX_ENABLE (u_short) (0x9<<11)
|
|
#define TX_DISABLE (u_short) (0xa<<11)
|
|
#define TX_RESET (u_short) (0xb<<11)
|
|
#define REQ_INTR (u_short) (0xc<<11)
|
|
/*
|
|
* The following C_* acknowledge the various interrupts. Some of them don't
|
|
* do anything. See the manual.
|
|
*/
|
|
#define ACK_INTR (u_short) (0x6800)
|
|
# define C_INTR_LATCH (u_short) (ACK_INTR|0x1)
|
|
# define C_CARD_FAILURE (u_short) (ACK_INTR|0x2)
|
|
# define C_TX_COMPLETE (u_short) (ACK_INTR|0x4)
|
|
# define C_TX_AVAIL (u_short) (ACK_INTR|0x8)
|
|
# define C_RX_COMPLETE (u_short) (ACK_INTR|0x10)
|
|
# define C_RX_EARLY (u_short) (ACK_INTR|0x20)
|
|
# define C_INT_RQD (u_short) (ACK_INTR|0x40)
|
|
# define C_UPD_STATS (u_short) (ACK_INTR|0x80)
|
|
#define SET_INTR_MASK (u_short) (0xe<<11)
|
|
#define SET_RD_0_MASK (u_short) (0xf<<11)
|
|
#define SET_RX_FILTER (u_short) (0x10<<11)
|
|
# define FIL_INDIVIDUAL (u_short) (0x1)
|
|
# define FIL_MULTICAST (u_short) (0x02)
|
|
# define FIL_BRDCST (u_short) (0x04)
|
|
# define FIL_PROMISC (u_short) (0x08)
|
|
#define SET_RX_EARLY_THRESH (u_short) (0x11<<11)
|
|
#define SET_TX_AVAIL_THRESH (u_short) (0x12<<11)
|
|
#define SET_TX_START_THRESH (u_short) (0x13<<11)
|
|
#define STATS_ENABLE (u_short) (0x15<<11)
|
|
#define STATS_DISABLE (u_short) (0x16<<11)
|
|
#define STOP_TRANSCEIVER (u_short) (0x17<<11)
|
|
#define TX_PLL_ENABLE (u_short) (0x18<<11)
|
|
#define TX_PLL_DISABLE (u_short) (0x19<<11)
|
|
#define POWER_UP (u_short) (0x1b<<11)
|
|
#define POWER_DOWN (u_short) (0x1b<<11)
|
|
#define POWER_AUTO (u_short) (0x1b<<11)
|
|
|
|
/*
|
|
* Status register. All windows.
|
|
*
|
|
* 15-13: Window number(0-7).
|
|
* 12: Command_in_progress.
|
|
* 11: reserved.
|
|
* 10: reserved.
|
|
* 9: reserved.
|
|
* 8: reserved.
|
|
* 7: Update Statistics.
|
|
* 6: Interrupt Requested.
|
|
* 5: RX Early.
|
|
* 4: RX Complete.
|
|
* 3: TX Available.
|
|
* 2: TX Complete.
|
|
* 1: Adapter Failure.
|
|
* 0: Interrupt Latch.
|
|
*/
|
|
#define S_INTR_LATCH (u_short) (0x1)
|
|
#define S_CARD_FAILURE (u_short) (0x2)
|
|
#define S_TX_COMPLETE (u_short) (0x4)
|
|
#define S_TX_AVAIL (u_short) (0x8)
|
|
#define S_RX_COMPLETE (u_short) (0x10)
|
|
#define S_RX_EARLY (u_short) (0x20)
|
|
#define S_INT_RQD (u_short) (0x40)
|
|
#define S_UPD_STATS (u_short) (0x80)
|
|
#define S_MASK (u_short) 0xFF /* mask of S_* */
|
|
#define S_5_INTS (S_CARD_FAILURE|S_TX_COMPLETE|\
|
|
S_TX_AVAIL|S_RX_COMPLETE|S_RX_EARLY)
|
|
#define S_COMMAND_IN_PROGRESS (u_short) (0x1000)
|
|
|
|
#define EP_BUSY_WAIT(sc) while (CSR_READ_2(sc, EP_STATUS) & S_COMMAND_IN_PROGRESS)
|
|
|
|
/* Address Config. Register.
|
|
* Window 0/Port 06
|
|
*/
|
|
|
|
#define ACF_CONNECTOR_BITS 14
|
|
#define ACF_CONNECTOR_UTP 0
|
|
#define ACF_CONNECTOR_AUI 1
|
|
#define ACF_CONNECTOR_BNC 3
|
|
|
|
/* Resource configuration register.
|
|
* Window 0/Port 08
|
|
*
|
|
*/
|
|
|
|
#define SET_IRQ(sc, irq) CSR_WRITE_2((sc), EP_W0_RESOURCE_CFG, \
|
|
((CSR_READ_2((sc), EP_W0_RESOURCE_CFG) & 0x0fff) | \
|
|
((u_short)(irq)<<12)) ) /* set IRQ i */
|
|
|
|
/*
|
|
* FIFO Registers.
|
|
* RX Status. Window 1/Port 08
|
|
*
|
|
* 15: Incomplete or FIFO empty.
|
|
* 14: 1: Error in RX Packet 0: Incomplete or no error.
|
|
* 13-11: Type of error.
|
|
* 1000 = Overrun.
|
|
* 1011 = Run Packet Error.
|
|
* 1100 = Alignment Error.
|
|
* 1101 = CRC Error.
|
|
* 1001 = Oversize Packet Error (>1514 bytes)
|
|
* 0010 = Dribble Bits.
|
|
* (all other error codes, no errors.)
|
|
*
|
|
* 10-0: RX Bytes (0-1514)
|
|
*/
|
|
#define ERR_RX_INCOMPLETE (u_short) (0x1<<15)
|
|
#define ERR_RX (u_short) (0x1<<14)
|
|
#define ERR_RX_OVERRUN (u_short) (0x8<<11)
|
|
#define ERR_RX_RUN_PKT (u_short) (0xb<<11)
|
|
#define ERR_RX_ALIGN (u_short) (0xc<<11)
|
|
#define ERR_RX_CRC (u_short) (0xd<<11)
|
|
#define ERR_RX_OVERSIZE (u_short) (0x9<<11)
|
|
#define ERR_RX_DRIBBLE (u_short) (0x2<<11)
|
|
|
|
/*
|
|
* FIFO Registers.
|
|
* TX Status. Window 1/Port 0B
|
|
*
|
|
* Reports the transmit status of a completed transmission. Writing this
|
|
* register pops the transmit completion stack.
|
|
*
|
|
* Window 1/Port 0x0b.
|
|
*
|
|
* 7: Complete
|
|
* 6: Interrupt on successful transmission requested.
|
|
* 5: Jabber Error (TP Only, TX Reset required. )
|
|
* 4: Underrun (TX Reset required. )
|
|
* 3: Maximum Collisions.
|
|
* 2: TX Status Overflow.
|
|
* 1-0: Undefined.
|
|
*
|
|
*/
|
|
#define TXS_COMPLETE 0x80
|
|
#define TXS_SUCCES_INTR_REQ 0x40
|
|
#define TXS_JABBER 0x20
|
|
#define TXS_UNDERRUN 0x10
|
|
#define TXS_MAX_COLLISION 0x8
|
|
#define TXS_STATUS_OVERFLOW 0x4
|
|
|
|
/*
|
|
* Configuration control register.
|
|
* Window 0/Port 04
|
|
*/
|
|
/* Read */
|
|
#define IS_AUI (1<<13)
|
|
#define IS_BNC (1<<12)
|
|
#define IS_UTP (1<<9)
|
|
/* Write */
|
|
#define ENABLE_DRQ_IRQ 0x0001
|
|
#define W0_P4_CMD_RESET_ADAPTER 0x4
|
|
#define W0_P4_CMD_ENABLE_ADAPTER 0x1
|
|
|
|
/*
|
|
* Media type and status.
|
|
* Window 4/Port 0A
|
|
*/
|
|
#define JABBER_GUARD_ENABLE 0x40
|
|
#define LINKBEAT_ENABLE 0x80
|
|
#define ENABLE_UTP (JABBER_GUARD_ENABLE | LINKBEAT_ENABLE)
|
|
#define DISABLE_UTP 0x0
|
|
#define MT_CSD 0x0004 /* CRC Strip disable */
|
|
#define MT_SQE 0x0008 /* SQE Enable */
|
|
#define MT_C0 0x0010 /* Collison */
|
|
#define MT_CS 0x0020 /* Carrier Sense */
|
|
#define MT_J 0x0200 /* Jabber detected */
|
|
#define MT_PL 0x0400 /* Plarity Inverted */
|
|
#define MT_LB 0x0800 /* Link Beat detected */
|
|
#define MT_SQ 0x1000 /* SQE Present */
|
|
#define MT_IN 0x2000 /* Reserved */
|
|
#define MT_CE 0x4000 /* Coax */
|
|
#define MT_TPE 0x8000
|
|
|
|
/*
|
|
* Misc defines for various things.
|
|
*/
|
|
#define ACTIVATE_ADAPTER_TO_CONFIG 0xff /* to the id_port */
|
|
#define MFG_ID 0x6d50 /* in EEPROM and W0
|
|
* ADDR_CONFIG */
|
|
#define PROD_ID 0x9150
|
|
|
|
#define AUI 0x1
|
|
#define BNC 0x2
|
|
#define UTP 0x4
|
|
|
|
#define RX_BYTES_MASK (u_short) (0x07ff)
|