Justin Hibbits 615df4c159 Increase default MAXTSIZ to allow execution of larger binaries. ...

This allows executing static clang built with -O0.

The value is configurable by a sysctl, so if one needs to clamp it down, they
still can.

Discussed with:	nwhitehorn,emaste

2015-01-10 06:54:10 +00:00

..

_align.h

…

_bus.h

…

_inttypes.h

…

_limits.h

…

_stdint.h

Newer versions of gcc define __INT64_C and __UINT64_C, so avoid

2013-09-03 22:04:55 +00:00

_types.h

Rename __wchar_t so it no longer conflicts with __wchar_t from clang 3.4

2014-04-01 14:46:11 +00:00

altivec.h

Dump VMX registers into the userland coredump.

2015-01-03 21:06:06 +00:00

asm.h

Revert r274772: it is not valid on MIPS

2014-11-25 03:50:31 +00:00

atomic.h

Small performance optimization. Clobber only cr0, rather than the entire CR.

2014-04-11 06:17:44 +00:00

bat.h

Update NetBSD Foundation copyrights to 2-clause BSD

2014-03-18 01:40:25 +00:00

bus_dma.h

…

bus.h

Update NetBSD Foundation copyrights to 2-clause BSD

2014-03-18 01:40:25 +00:00

clock.h

…

counter.h

Small performance optimization. Clobber only cr0, rather than the entire CR.

2014-04-11 06:17:44 +00:00

cpu.h

Unbreak non-SMP builds. This was broken by r259284. Also, reorganize the

2014-01-31 03:55:34 +00:00

cpufunc.h

…

db_machdep.h

Truncate DB_SMALL_VALUE_MAX to a much lower value.

2015-01-04 01:45:26 +00:00

dbdma.h

Add PMU-based CPU frequency scaling. This method is used on most Titanium

2013-12-13 02:37:35 +00:00

dump.h

Factor out duplicated code from dumpsys() on each architecture into generic

2015-01-07 01:01:39 +00:00

elf.h

…

endian.h

In case we ever support little-endian PowerPC (probably userland only),

2014-07-06 16:20:37 +00:00

exec.h

…

float.h

…

floatingpoint.h

…

fpu.h

…

frame.h

Also align the 32-bit PowerPC stacks.

2013-09-05 23:28:50 +00:00

gdb_machdep.h

Fix the PowerPC Book-E register definitions used by the remote GDB

2013-05-21 18:00:47 +00:00

hid.h

…

ieee.h

…

ieeefp.h

…

in_cksum.h

…

intr_machdep.h

Allow PIC drivers to translate firmware sense codes for themselves. This

2013-10-24 15:37:32 +00:00

kdb.h

…

limits.h

…

machdep.h

…

md_var.h

…

memdev.h

…

metadata.h

…

mmuvar.h

…

ofw_machdep.h

Rearchitect platform memory map parsing to make it less

2013-12-01 19:43:15 +00:00

openpicreg.h

Add suspend/resume state saving for OpenPIC on PowerMac. It's likely this

2013-12-21 04:31:54 +00:00

openpicvar.h

Add suspend/resume state saving for OpenPIC on PowerMac. It's likely this

2013-12-21 04:31:54 +00:00

param.h

Fix typo.

2013-11-13 01:51:40 +00:00

pcb.h

Resort and resize the altivec registers in the pcb. vrsave and vscr are both

2015-01-03 21:08:27 +00:00

pcpu.h

Add PMU-based CPU frequency scaling. This method is used on most Titanium

2013-12-13 02:37:35 +00:00

pio.h

…

platform.h

Unbreak non-SMP builds. This was broken by r259284. Also, reorganize the

2014-01-31 03:55:34 +00:00

platformvar.h

…

pmap.h

Factor out duplicated code from dumpsys() on each architecture into generic

2015-01-07 01:01:39 +00:00

pmc_mdep.h

Add hwpmc(4) support for the PowerPC 970 class processors, direct events.

2014-02-01 02:03:50 +00:00

proc.h

Implement GET_STACK_USAGE() on PowerPC. This implementation is identical

2013-10-02 20:40:21 +00:00

profile.h

Revert r274772: it is not valid on MIPS

2014-11-25 03:50:31 +00:00

psl.h

Correct the SRR1 mask, it's 10-15 not 10-11.

2014-04-06 06:18:43 +00:00

pte.h

Use the canonical bits for wired, etc. in the PTE. This is important for

2013-09-09 12:44:48 +00:00

ptrace.h

…

reg.h

…

reloc.h

…

resource.h

…

rtas.h

…

runq.h

…

sc_machdep.h

…

setjmp.h

…

sigframe.h

…

signal.h

…

slb.h

…

smp.h

…

spr.h

Add a new CPU id for a POWER8 variant.

2014-07-06 16:19:55 +00:00

sr.h

…

stack.h

…

stdarg.h

…

sysarch.h

…

tlb.h

Interrelated improvements to early boot mappings:

2013-10-26 18:18:14 +00:00

trap.h

Add support for dtrace:fbt on modules for PowerPC

2014-11-29 20:54:33 +00:00

ucontext.h

…

varargs.h

…

vdso.h

…

vm.h

…

vmparam.h

Increase default MAXTSIZ to allow execution of larger binaries.

2015-01-10 06:54:10 +00:00