196848bce4
Clean out the abortive start to homegrown, per-mpt, Domain Validation. This should really be done at a higher level. Use the PIM_SEQSCAN flag for U320- this seems to correct cases of being unable to consistently negotiate U320 in the cases where I'd seen this before. Between this and other recent checkins, this driver is pretty close to being ready for MFC. Reviewed by: scottl, ken, scsi@ MFC after: 1 week
1181 lines
37 KiB
C
1181 lines
37 KiB
C
/* $FreeBSD$ */
|
|
/*-
|
|
* Generic defines for LSI '909 FC adapters.
|
|
* FreeBSD Version.
|
|
*
|
|
* Copyright (c) 2000, 2001 by Greg Ansley
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice immediately at the beginning of the file, without modification,
|
|
* this list of conditions, and the following disclaimer.
|
|
* 2. The name of the author may not be used to endorse or promote products
|
|
* derived from this software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
|
|
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGE.
|
|
*/
|
|
/*-
|
|
* Copyright (c) 2002, 2006 by Matthew Jacob
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions are
|
|
* met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce at minimum a disclaimer
|
|
* substantially similar to the "NO WARRANTY" disclaimer below
|
|
* ("Disclaimer") and any redistribution must be conditioned upon including
|
|
* a substantially similar Disclaimer requirement for further binary
|
|
* redistribution.
|
|
* 3. Neither the names of the above listed copyright holders nor the names
|
|
* of any contributors may be used to endorse or promote products derived
|
|
* from this software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
|
|
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
|
|
* LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
|
|
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
|
|
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
|
|
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
|
|
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
|
|
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF THE COPYRIGHT
|
|
* OWNER OR CONTRIBUTOR IS ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
*
|
|
* Support from Chris Ellsworth in order to make SAS adapters work
|
|
* is gratefully acknowledged.
|
|
*
|
|
*
|
|
* Support from LSI-Logic has also gone a great deal toward making this a
|
|
* workable subsystem and is gratefully acknowledged.
|
|
*/
|
|
/*
|
|
* Copyright (c) 2004, Avid Technology, Inc. and its contributors.
|
|
* Copyright (c) 2004, 2005 Justin T. Gibbs
|
|
* Copyright (c) 2005, WHEEL Sp. z o.o.
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions are
|
|
* met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce at minimum a disclaimer
|
|
* substantially similar to the "NO WARRANTY" disclaimer below
|
|
* ("Disclaimer") and any redistribution must be conditioned upon including
|
|
* a substantially similar Disclaimer requirement for further binary
|
|
* redistribution.
|
|
* 3. Neither the names of the above listed copyright holders nor the names
|
|
* of any contributors may be used to endorse or promote products derived
|
|
* from this software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
|
|
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
|
|
* LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
|
|
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
|
|
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
|
|
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
|
|
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
|
|
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF THE COPYRIGHT
|
|
* OWNER OR CONTRIBUTOR IS ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
*/
|
|
|
|
#ifndef _MPT_H_
|
|
#define _MPT_H_
|
|
|
|
/********************************* OS Includes ********************************/
|
|
#include <sys/types.h>
|
|
#include <sys/param.h>
|
|
#include <sys/systm.h>
|
|
#include <sys/endian.h>
|
|
#include <sys/eventhandler.h>
|
|
#if __FreeBSD_version < 500000
|
|
#include <sys/kernel.h>
|
|
#include <sys/queue.h>
|
|
#include <sys/malloc.h>
|
|
#else
|
|
#include <sys/lock.h>
|
|
#include <sys/kernel.h>
|
|
#include <sys/queue.h>
|
|
#include <sys/malloc.h>
|
|
#include <sys/mutex.h>
|
|
#include <sys/condvar.h>
|
|
#endif
|
|
#include <sys/proc.h>
|
|
#include <sys/bus.h>
|
|
#include <sys/module.h>
|
|
|
|
#include <machine/cpu.h>
|
|
#include <machine/resource.h>
|
|
|
|
#if __FreeBSD_version < 500000
|
|
#include <machine/bus.h>
|
|
#include <machine/clock.h>
|
|
#endif
|
|
|
|
#include <sys/rman.h>
|
|
|
|
#if __FreeBSD_version < 500000
|
|
#include <pci/pcireg.h>
|
|
#include <pci/pcivar.h>
|
|
#else
|
|
#include <dev/pci/pcireg.h>
|
|
#include <dev/pci/pcivar.h>
|
|
#endif
|
|
|
|
#include <machine/bus.h>
|
|
#include "opt_ddb.h"
|
|
|
|
/**************************** Register Definitions ****************************/
|
|
#include <dev/mpt/mpt_reg.h>
|
|
|
|
/******************************* MPI Definitions ******************************/
|
|
#include <dev/mpt/mpilib/mpi_type.h>
|
|
#include <dev/mpt/mpilib/mpi.h>
|
|
#include <dev/mpt/mpilib/mpi_cnfg.h>
|
|
#include <dev/mpt/mpilib/mpi_ioc.h>
|
|
#include <dev/mpt/mpilib/mpi_raid.h>
|
|
|
|
/* XXX For mpt_debug.c */
|
|
#include <dev/mpt/mpilib/mpi_init.h>
|
|
|
|
/****************************** Misc Definitions ******************************/
|
|
#define MPT_OK (0)
|
|
#define MPT_FAIL (0x10000)
|
|
|
|
#define NUM_ELEMENTS(array) (sizeof(array) / sizeof(*array))
|
|
|
|
#define MPT_ROLE_NONE 0
|
|
#define MPT_ROLE_INITIATOR 1
|
|
#define MPT_ROLE_TARGET 2
|
|
#define MPT_ROLE_BOTH 3
|
|
#define MPT_ROLE_DEFAULT MPT_ROLE_INITIATOR
|
|
|
|
/**************************** Forward Declarations ****************************/
|
|
struct mpt_softc;
|
|
struct mpt_personality;
|
|
typedef struct req_entry request_t;
|
|
|
|
/************************* Personality Module Support *************************/
|
|
typedef int mpt_load_handler_t(struct mpt_personality *);
|
|
typedef int mpt_probe_handler_t(struct mpt_softc *);
|
|
typedef int mpt_attach_handler_t(struct mpt_softc *);
|
|
typedef int mpt_enable_handler_t(struct mpt_softc *);
|
|
typedef int mpt_event_handler_t(struct mpt_softc *, request_t *,
|
|
MSG_EVENT_NOTIFY_REPLY *);
|
|
typedef void mpt_reset_handler_t(struct mpt_softc *, int /*type*/);
|
|
/* XXX Add return value and use for veto? */
|
|
typedef void mpt_shutdown_handler_t(struct mpt_softc *);
|
|
typedef void mpt_detach_handler_t(struct mpt_softc *);
|
|
typedef int mpt_unload_handler_t(struct mpt_personality *);
|
|
|
|
struct mpt_personality
|
|
{
|
|
const char *name;
|
|
uint32_t id; /* Assigned identifier. */
|
|
u_int use_count; /* Instances using personality*/
|
|
mpt_load_handler_t *load; /* configure personailty */
|
|
#define MPT_PERS_FIRST_HANDLER(pers) (&(pers)->load)
|
|
mpt_probe_handler_t *probe; /* configure personailty */
|
|
mpt_attach_handler_t *attach; /* initialize device instance */
|
|
mpt_enable_handler_t *enable; /* enable device */
|
|
mpt_event_handler_t *event; /* Handle MPI event. */
|
|
mpt_reset_handler_t *reset; /* Re-init after reset. */
|
|
mpt_shutdown_handler_t *shutdown; /* Shutdown instance. */
|
|
mpt_detach_handler_t *detach; /* release device instance */
|
|
mpt_unload_handler_t *unload; /* Shutdown personality */
|
|
#define MPT_PERS_LAST_HANDLER(pers) (&(pers)->unload)
|
|
};
|
|
|
|
int mpt_modevent(module_t, int, void *);
|
|
|
|
/* Maximum supported number of personalities. */
|
|
#define MPT_MAX_PERSONALITIES (15)
|
|
|
|
#define MPT_PERSONALITY_DEPEND(name, dep, vmin, vpref, vmax) \
|
|
MODULE_DEPEND(name, dep, vmin, vpref, vmax)
|
|
|
|
#define DECLARE_MPT_PERSONALITY(name, order) \
|
|
static moduledata_t name##_mod = { \
|
|
#name, mpt_modevent, &name##_personality \
|
|
}; \
|
|
DECLARE_MODULE(name, name##_mod, SI_SUB_DRIVERS, order); \
|
|
MODULE_VERSION(name, 1); \
|
|
MPT_PERSONALITY_DEPEND(name, mpt_core, 1, 1, 1)
|
|
|
|
/******************************* Bus DMA Support ******************************/
|
|
/* XXX Need to update bus_dmamap_sync to take a range argument. */
|
|
#define bus_dmamap_sync_range(dma_tag, dmamap, offset, len, op) \
|
|
bus_dmamap_sync(dma_tag, dmamap, op)
|
|
|
|
#if __FreeBSD_version >= 501102
|
|
#define mpt_dma_tag_create(mpt, parent_tag, alignment, boundary, \
|
|
lowaddr, highaddr, filter, filterarg, \
|
|
maxsize, nsegments, maxsegsz, flags, \
|
|
dma_tagp) \
|
|
bus_dma_tag_create(parent_tag, alignment, boundary, \
|
|
lowaddr, highaddr, filter, filterarg, \
|
|
maxsize, nsegments, maxsegsz, flags, \
|
|
busdma_lock_mutex, &Giant, \
|
|
dma_tagp)
|
|
#else
|
|
#define mpt_dma_tag_create(mpt, parent_tag, alignment, boundary, \
|
|
lowaddr, highaddr, filter, filterarg, \
|
|
maxsize, nsegments, maxsegsz, flags, \
|
|
dma_tagp) \
|
|
bus_dma_tag_create(parent_tag, alignment, boundary, \
|
|
lowaddr, highaddr, filter, filterarg, \
|
|
maxsize, nsegments, maxsegsz, flags, \
|
|
dma_tagp)
|
|
#endif
|
|
|
|
struct mpt_map_info {
|
|
struct mpt_softc *mpt;
|
|
int error;
|
|
uint32_t phys;
|
|
};
|
|
|
|
void mpt_map_rquest(void *, bus_dma_segment_t *, int, int);
|
|
|
|
/**************************** Kernel Thread Support ***************************/
|
|
#if __FreeBSD_version > 500005
|
|
#define mpt_kthread_create(func, farg, proc_ptr, flags, stackpgs, fmtstr, arg) \
|
|
kthread_create(func, farg, proc_ptr, flags, stackpgs, fmtstr, arg)
|
|
#else
|
|
#define mpt_kthread_create(func, farg, proc_ptr, flags, stackpgs, fmtstr, arg) \
|
|
kthread_create(func, farg, proc_ptr, fmtstr, arg)
|
|
#endif
|
|
|
|
/****************************** Timer Facilities ******************************/
|
|
#if __FreeBSD_version > 500000
|
|
#define mpt_callout_init(c) callout_init(c, /*mpsafe*/0);
|
|
#else
|
|
#define mpt_callout_init(c) callout_init(c);
|
|
#endif
|
|
|
|
/********************************** Endianess *********************************/
|
|
static __inline uint64_t
|
|
u64toh(U64 s)
|
|
{
|
|
uint64_t result;
|
|
|
|
result = le32toh(s.Low);
|
|
result |= ((uint64_t)le32toh(s.High)) << 32;
|
|
return (result);
|
|
}
|
|
|
|
/**************************** MPI Transaction State ***************************/
|
|
typedef enum {
|
|
REQ_STATE_NIL = 0x00,
|
|
REQ_STATE_FREE = 0x01,
|
|
REQ_STATE_ALLOCATED = 0x02,
|
|
REQ_STATE_QUEUED = 0x04,
|
|
REQ_STATE_DONE = 0x08,
|
|
REQ_STATE_TIMEDOUT = 0x10,
|
|
REQ_STATE_NEED_WAKEUP = 0x20,
|
|
REQ_STATE_LOCKED = 0x80, /* can't be freed */
|
|
REQ_STATE_MASK = 0xFF
|
|
} mpt_req_state_t;
|
|
|
|
struct req_entry {
|
|
TAILQ_ENTRY(req_entry) links; /* Pointer to next in list */
|
|
mpt_req_state_t state; /* Request State Information */
|
|
uint16_t index; /* Index of this entry */
|
|
uint16_t IOCStatus; /* Completion status */
|
|
uint16_t ResponseCode; /* TMF Reponse Code */
|
|
uint16_t serno; /* serial number */
|
|
union ccb *ccb; /* CAM request */
|
|
void *req_vbuf; /* Virtual Address of Entry */
|
|
void *sense_vbuf; /* Virtual Address of sense data */
|
|
bus_addr_t req_pbuf; /* Physical Address of Entry */
|
|
bus_addr_t sense_pbuf; /* Physical Address of sense data */
|
|
bus_dmamap_t dmap; /* DMA map for data buffers */
|
|
struct req_entry *chain; /* for SGE overallocations */
|
|
};
|
|
|
|
/**************************** MPI Target State Info ***************************/
|
|
|
|
typedef struct {
|
|
uint32_t reply_desc; /* current reply descriptor */
|
|
uint32_t resid; /* current data residual */
|
|
uint32_t bytes_xfered; /* current relative offset */
|
|
union ccb *ccb; /* pointer to currently active ccb */
|
|
request_t *req; /* pointer to currently active assist request */
|
|
int nxfers;
|
|
uint32_t tag_id;
|
|
enum {
|
|
TGT_STATE_NIL,
|
|
TGT_STATE_LOADING,
|
|
TGT_STATE_LOADED,
|
|
TGT_STATE_IN_CAM,
|
|
TGT_STATE_SETTING_UP_FOR_DATA,
|
|
TGT_STATE_MOVING_DATA,
|
|
TGT_STATE_MOVING_DATA_AND_STATUS,
|
|
TGT_STATE_SENDING_STATUS
|
|
} state;
|
|
} mpt_tgt_state_t;
|
|
|
|
/*
|
|
* When we get an incoming command it has its own tag which is called the
|
|
* IoIndex. This is the value we gave that particular command buffer when
|
|
* we originally assigned it. It's just a number, really. The FC card uses
|
|
* it as an RX_ID. We can use it to index into mpt->tgt_cmd_ptrs, which
|
|
* contains pointers the request_t structures related to that IoIndex.
|
|
*
|
|
* What *we* do is construct a tag out of the index for the target command
|
|
* which owns the incoming ATIO plus a rolling sequence number.
|
|
*/
|
|
#define MPT_MAKE_TAGID(mpt, req, ioindex) \
|
|
((ioindex << 18) | (((mpt->sequence++) & 0x3f) << 12) | (req->index & 0xfff))
|
|
|
|
#ifdef INVARIANTS
|
|
#define MPT_TAG_2_REQ(a, b) mpt_tag_2_req(a, (uint32_t) b)
|
|
#else
|
|
#define MPT_TAG_2_REQ(mpt, tag) mpt->tgt_cmd_ptrs[tag >> 18]
|
|
#endif
|
|
|
|
#define MPT_TGT_STATE(mpt, req) ((mpt_tgt_state_t *) \
|
|
(&((uint8_t *)req->req_vbuf)[MPT_RQSL(mpt) - sizeof (mpt_tgt_state_t)]))
|
|
|
|
STAILQ_HEAD(mpt_hdr_stailq, ccb_hdr);
|
|
#define MPT_MAX_LUNS 256
|
|
typedef struct {
|
|
struct mpt_hdr_stailq atios;
|
|
struct mpt_hdr_stailq inots;
|
|
int enabled;
|
|
} tgt_resource_t;
|
|
#define MPT_MAX_ELS 64
|
|
|
|
/**************************** Handler Registration ****************************/
|
|
/*
|
|
* Global table of registered reply handlers. The
|
|
* handler is indicated by byte 3 of the request
|
|
* index submitted to the IOC. This allows the
|
|
* driver core to perform generic processing without
|
|
* any knowledge of per-personality behavior.
|
|
*
|
|
* MPT_NUM_REPLY_HANDLERS must be a power of 2
|
|
* to allow the easy generation of a mask.
|
|
*
|
|
* The handler offsets used by the core are hard coded
|
|
* allowing faster code generation when assigning a handler
|
|
* to a request. All "personalities" must use the
|
|
* the handler registration mechanism.
|
|
*
|
|
* The IOC handlers that are rarely executed are placed
|
|
* at the tail of the table to make it more likely that
|
|
* all commonly executed handlers fit in a single cache
|
|
* line.
|
|
*/
|
|
#define MPT_NUM_REPLY_HANDLERS (32)
|
|
#define MPT_REPLY_HANDLER_EVENTS MPT_CBI_TO_HID(0)
|
|
#define MPT_REPLY_HANDLER_CONFIG MPT_CBI_TO_HID(MPT_NUM_REPLY_HANDLERS-1)
|
|
#define MPT_REPLY_HANDLER_HANDSHAKE MPT_CBI_TO_HID(MPT_NUM_REPLY_HANDLERS-2)
|
|
typedef int mpt_reply_handler_t(struct mpt_softc *mpt, request_t *request,
|
|
uint32_t reply_desc, MSG_DEFAULT_REPLY *reply_frame);
|
|
typedef union {
|
|
mpt_reply_handler_t *reply_handler;
|
|
} mpt_handler_t;
|
|
|
|
typedef enum {
|
|
MPT_HANDLER_REPLY,
|
|
MPT_HANDLER_EVENT,
|
|
MPT_HANDLER_RESET,
|
|
MPT_HANDLER_SHUTDOWN
|
|
} mpt_handler_type;
|
|
|
|
struct mpt_handler_record
|
|
{
|
|
LIST_ENTRY(mpt_handler_record) links;
|
|
mpt_handler_t handler;
|
|
};
|
|
|
|
LIST_HEAD(mpt_handler_list, mpt_handler_record);
|
|
|
|
/*
|
|
* The handler_id is currently unused but would contain the
|
|
* handler ID used in the MsgContext field to allow direction
|
|
* of replies to the handler. Registrations that don't require
|
|
* a handler id can pass in NULL for the handler_id.
|
|
*
|
|
* Deregistrations for handlers without a handler id should
|
|
* pass in MPT_HANDLER_ID_NONE.
|
|
*/
|
|
#define MPT_HANDLER_ID_NONE (0xFFFFFFFF)
|
|
int mpt_register_handler(struct mpt_softc *, mpt_handler_type,
|
|
mpt_handler_t, uint32_t *);
|
|
int mpt_deregister_handler(struct mpt_softc *, mpt_handler_type,
|
|
mpt_handler_t, uint32_t);
|
|
|
|
/******************* Per-Controller Instance Data Structures ******************/
|
|
TAILQ_HEAD(req_queue, req_entry);
|
|
|
|
/* Structure for saving proper values for modifyable PCI config registers */
|
|
struct mpt_pci_cfg {
|
|
uint16_t Command;
|
|
uint16_t LatencyTimer_LineSize;
|
|
uint32_t IO_BAR;
|
|
uint32_t Mem0_BAR[2];
|
|
uint32_t Mem1_BAR[2];
|
|
uint32_t ROM_BAR;
|
|
uint8_t IntLine;
|
|
uint32_t PMCSR;
|
|
};
|
|
|
|
typedef enum {
|
|
MPT_RVF_NONE = 0x0,
|
|
MPT_RVF_ACTIVE = 0x1,
|
|
MPT_RVF_ANNOUNCED = 0x2,
|
|
MPT_RVF_UP2DATE = 0x4,
|
|
MPT_RVF_REFERENCED = 0x8,
|
|
MPT_RVF_WCE_CHANGED = 0x10
|
|
} mpt_raid_volume_flags;
|
|
|
|
struct mpt_raid_volume {
|
|
CONFIG_PAGE_RAID_VOL_0 *config_page;
|
|
MPI_RAID_VOL_INDICATOR sync_progress;
|
|
mpt_raid_volume_flags flags;
|
|
u_int quiesced_disks;
|
|
};
|
|
|
|
typedef enum {
|
|
MPT_RDF_NONE = 0x00,
|
|
MPT_RDF_ACTIVE = 0x01,
|
|
MPT_RDF_ANNOUNCED = 0x02,
|
|
MPT_RDF_UP2DATE = 0x04,
|
|
MPT_RDF_REFERENCED = 0x08,
|
|
MPT_RDF_QUIESCING = 0x10,
|
|
MPT_RDF_QUIESCED = 0x20
|
|
} mpt_raid_disk_flags;
|
|
|
|
struct mpt_raid_disk {
|
|
CONFIG_PAGE_RAID_PHYS_DISK_0 config_page;
|
|
struct mpt_raid_volume *volume;
|
|
u_int member_number;
|
|
u_int pass_thru_active;
|
|
mpt_raid_disk_flags flags;
|
|
};
|
|
|
|
struct mpt_evtf_record {
|
|
MSG_EVENT_NOTIFY_REPLY reply;
|
|
uint32_t context;
|
|
LIST_ENTRY(mpt_evtf_record) links;
|
|
};
|
|
|
|
LIST_HEAD(mpt_evtf_list, mpt_evtf_record);
|
|
|
|
struct mpt_softc {
|
|
device_t dev;
|
|
#if __FreeBSD_version < 500000
|
|
uint32_t mpt_islocked;
|
|
int mpt_splsaved;
|
|
#else
|
|
struct mtx mpt_lock;
|
|
int mpt_locksetup;
|
|
#endif
|
|
uint32_t mpt_pers_mask;
|
|
uint32_t : 8,
|
|
unit : 8,
|
|
: 1,
|
|
twildcard : 1,
|
|
tenabled : 1,
|
|
role : 2, /* none, ini, target, both */
|
|
: 1,
|
|
raid_enabled : 1,
|
|
raid_mwce_set : 1,
|
|
getreqwaiter : 1,
|
|
shutdwn_raid : 1,
|
|
shutdwn_recovery: 1,
|
|
outofbeer : 1,
|
|
disabled : 1,
|
|
is_spi : 1,
|
|
is_sas : 1,
|
|
is_fc : 1;
|
|
|
|
u_int verbose;
|
|
|
|
/*
|
|
* IOC Facts
|
|
*/
|
|
uint16_t mpt_global_credits;
|
|
uint16_t request_frame_size;
|
|
uint8_t mpt_max_devices;
|
|
uint8_t mpt_max_buses;
|
|
uint8_t ioc_facts_flags;
|
|
uint8_t padding0;
|
|
|
|
/*
|
|
* Port Facts
|
|
* XXX - Add multi-port support!.
|
|
*/
|
|
uint16_t mpt_ini_id;
|
|
uint16_t mpt_port_type;
|
|
uint16_t mpt_proto_flags;
|
|
uint16_t mpt_max_tgtcmds;
|
|
|
|
/*
|
|
* Device Configuration Information
|
|
*/
|
|
union {
|
|
struct mpt_spi_cfg {
|
|
CONFIG_PAGE_SCSI_PORT_0 _port_page0;
|
|
CONFIG_PAGE_SCSI_PORT_1 _port_page1;
|
|
CONFIG_PAGE_SCSI_PORT_2 _port_page2;
|
|
CONFIG_PAGE_SCSI_DEVICE_0 _dev_page0[16];
|
|
CONFIG_PAGE_SCSI_DEVICE_1 _dev_page1[16];
|
|
uint16_t _tag_enable;
|
|
uint16_t _disc_enable;
|
|
} spi;
|
|
#define mpt_port_page0 cfg.spi._port_page0
|
|
#define mpt_port_page1 cfg.spi._port_page1
|
|
#define mpt_port_page2 cfg.spi._port_page2
|
|
#define mpt_dev_page0 cfg.spi._dev_page0
|
|
#define mpt_dev_page1 cfg.spi._dev_page1
|
|
#define mpt_tag_enable cfg.spi._tag_enable
|
|
#define mpt_disc_enable cfg.spi._disc_enable
|
|
struct mpi_fc_cfg {
|
|
CONFIG_PAGE_FC_PORT_0 _port_page0;
|
|
#define mpt_fcport_page0 cfg.fc._port_page0
|
|
} fc;
|
|
} cfg;
|
|
|
|
/* Controller Info for RAID information */
|
|
CONFIG_PAGE_IOC_2 * ioc_page2;
|
|
CONFIG_PAGE_IOC_3 * ioc_page3;
|
|
|
|
/* Raid Data */
|
|
struct mpt_raid_volume* raid_volumes;
|
|
struct mpt_raid_disk* raid_disks;
|
|
u_int raid_max_volumes;
|
|
u_int raid_max_disks;
|
|
u_int raid_page0_len;
|
|
u_int raid_wakeup;
|
|
u_int raid_rescan;
|
|
u_int raid_resync_rate;
|
|
u_int raid_mwce_setting;
|
|
u_int raid_queue_depth;
|
|
u_int raid_nonopt_volumes;
|
|
struct proc *raid_thread;
|
|
struct callout raid_timer;
|
|
|
|
/*
|
|
* PCI Hardware info
|
|
*/
|
|
struct resource * pci_irq; /* Interrupt map for chip */
|
|
void * ih; /* Interupt handle */
|
|
struct mpt_pci_cfg pci_cfg; /* saved PCI conf registers */
|
|
|
|
/*
|
|
* DMA Mapping Stuff
|
|
*/
|
|
struct resource * pci_reg; /* Register map for chip */
|
|
int pci_mem_rid; /* Resource ID */
|
|
bus_space_tag_t pci_st; /* Bus tag for registers */
|
|
bus_space_handle_t pci_sh; /* Bus handle for registers */
|
|
/* PIO versions of above. */
|
|
int pci_pio_rid;
|
|
struct resource * pci_pio_reg;
|
|
bus_space_tag_t pci_pio_st;
|
|
bus_space_handle_t pci_pio_sh;
|
|
|
|
bus_dma_tag_t parent_dmat; /* DMA tag for parent PCI bus */
|
|
bus_dma_tag_t reply_dmat; /* DMA tag for reply memory */
|
|
bus_dmamap_t reply_dmap; /* DMA map for reply memory */
|
|
uint8_t *reply; /* KVA of reply memory */
|
|
bus_addr_t reply_phys; /* BusAddr of reply memory */
|
|
|
|
bus_dma_tag_t buffer_dmat; /* DMA tag for buffers */
|
|
bus_dma_tag_t request_dmat; /* DMA tag for request memroy */
|
|
bus_dmamap_t request_dmap; /* DMA map for request memroy */
|
|
uint8_t *request; /* KVA of Request memory */
|
|
bus_addr_t request_phys; /* BusAddr of request memory */
|
|
|
|
uint32_t max_seg_cnt; /* calculated after IOC facts */
|
|
|
|
/*
|
|
* Hardware management
|
|
*/
|
|
u_int reset_cnt;
|
|
|
|
/*
|
|
* CAM && Software Management
|
|
*/
|
|
request_t *request_pool;
|
|
struct req_queue request_free_list;
|
|
struct req_queue request_pending_list;
|
|
struct req_queue request_timeout_list;
|
|
|
|
|
|
struct cam_sim *sim;
|
|
struct cam_path *path;
|
|
|
|
struct cam_sim *phydisk_sim;
|
|
struct cam_path *phydisk_path;
|
|
|
|
struct proc *recovery_thread;
|
|
request_t *tmf_req;
|
|
|
|
/*
|
|
* Deferred frame acks due to resource shortage.
|
|
*/
|
|
struct mpt_evtf_list ack_frames;
|
|
|
|
/*
|
|
* Target Mode Support
|
|
*/
|
|
uint32_t scsi_tgt_handler_id;
|
|
request_t ** tgt_cmd_ptrs;
|
|
request_t ** els_cmd_ptrs; /* FC only */
|
|
|
|
/*
|
|
* *snork*- this is chosen to be here *just in case* somebody
|
|
* forgets to point to it exactly and we index off of trt with
|
|
* CAM_LUN_WILDCARD.
|
|
*/
|
|
tgt_resource_t trt_wildcard; /* wildcard luns */
|
|
tgt_resource_t trt[MPT_MAX_LUNS];
|
|
uint16_t tgt_cmds_allocated;
|
|
uint16_t els_cmds_allocated; /* FC only */
|
|
|
|
uint16_t timeouts; /* timeout count */
|
|
uint16_t success; /* successes afer timeout */
|
|
uint16_t sequence; /* Sequence Number */
|
|
uint16_t pad3;
|
|
|
|
|
|
/* Paired port in some dual adapters configurations */
|
|
struct mpt_softc * mpt2;
|
|
|
|
/* FW Image management */
|
|
uint32_t fw_image_size;
|
|
uint8_t *fw_image;
|
|
bus_dma_tag_t fw_dmat; /* DMA tag for firmware image */
|
|
bus_dmamap_t fw_dmap; /* DMA map for firmware image */
|
|
bus_addr_t fw_phys; /* BusAddr of firmware image */
|
|
|
|
/* Shutdown Event Handler. */
|
|
eventhandler_tag eh;
|
|
|
|
TAILQ_ENTRY(mpt_softc) links;
|
|
};
|
|
|
|
static __inline void mpt_assign_serno(struct mpt_softc *, request_t *);
|
|
|
|
static __inline void
|
|
mpt_assign_serno(struct mpt_softc *mpt, request_t *req)
|
|
{
|
|
if ((req->serno = mpt->sequence++) == 0) {
|
|
req->serno = mpt->sequence++;
|
|
}
|
|
}
|
|
|
|
/***************************** Locking Primitives *****************************/
|
|
#if __FreeBSD_version < 500000
|
|
#define MPT_IFLAGS INTR_TYPE_CAM
|
|
#define MPT_LOCK(mpt) mpt_lockspl(mpt)
|
|
#define MPT_UNLOCK(mpt) mpt_unlockspl(mpt)
|
|
#define MPT_OWNED(mpt) mpt->mpt_islocked
|
|
#define MPTLOCK_2_CAMLOCK MPT_UNLOCK
|
|
#define CAMLOCK_2_MPTLOCK MPT_LOCK
|
|
#define MPT_LOCK_SETUP(mpt)
|
|
#define MPT_LOCK_DESTROY(mpt)
|
|
|
|
static __inline void mpt_lockspl(struct mpt_softc *mpt);
|
|
static __inline void mpt_unlockspl(struct mpt_softc *mpt);
|
|
|
|
static __inline void
|
|
mpt_lockspl(struct mpt_softc *mpt)
|
|
{
|
|
int s;
|
|
|
|
s = splcam();
|
|
if (mpt->mpt_islocked++ == 0) {
|
|
mpt->mpt_splsaved = s;
|
|
} else {
|
|
splx(s);
|
|
panic("Recursed lock with mask: 0x%x\n", s);
|
|
}
|
|
}
|
|
|
|
static __inline void
|
|
mpt_unlockspl(struct mpt_softc *mpt)
|
|
{
|
|
if (mpt->mpt_islocked) {
|
|
if (--mpt->mpt_islocked == 0) {
|
|
splx(mpt->mpt_splsaved);
|
|
}
|
|
} else
|
|
panic("Negative lock count\n");
|
|
}
|
|
|
|
static __inline int
|
|
mpt_sleep(struct mpt_softc *mpt, void *ident, int priority,
|
|
const char *wmesg, int timo)
|
|
{
|
|
int saved_cnt;
|
|
int saved_spl;
|
|
int error;
|
|
|
|
KASSERT(mpt->mpt_islocked <= 1, ("Invalid lock count on tsleep"));
|
|
saved_cnt = mpt->mpt_islocked;
|
|
saved_spl = mpt->mpt_splsaved;
|
|
mpt->mpt_islocked = 0;
|
|
error = tsleep(ident, priority, wmesg, timo);
|
|
KASSERT(mpt->mpt_islocked == 0, ("Invalid lock count on wakeup"));
|
|
mpt->mpt_islocked = saved_cnt;
|
|
mpt->mpt_splsaved = saved_spl;
|
|
return (error);
|
|
}
|
|
|
|
#else
|
|
#ifdef LOCKING_WORKED_AS_IT_SHOULD
|
|
#error "Shouldn't Be Here!"
|
|
#define MPT_IFLAGS INTR_TYPE_CAM | INTR_ENTROPY | INTR_MPSAFE
|
|
#define MPT_LOCK_SETUP(mpt) \
|
|
mtx_init(&mpt->mpt_lock, "mpt", NULL, MTX_DEF); \
|
|
mpt->mpt_locksetup = 1
|
|
#define MPT_LOCK_DESTROY(mpt) \
|
|
if (mpt->mpt_locksetup) { \
|
|
mtx_destroy(&mpt->mpt_lock); \
|
|
mpt->mpt_locksetup = 0; \
|
|
}
|
|
|
|
#define MPT_LOCK(mpt) mtx_lock(&(mpt)->mpt_lock)
|
|
#define MPT_UNLOCK(mpt) mtx_unlock(&(mpt)->mpt_lock)
|
|
#define MPT_OWNED(mpt) mtx_owned(&(mpt)->mpt_lock)
|
|
#define MPTLOCK_2_CAMLOCK(mpt) \
|
|
mtx_unlock(&(mpt)->mpt_lock); mtx_lock(&Giant)
|
|
#define CAMLOCK_2_MPTLOCK(mpt) \
|
|
mtx_unlock(&Giant); mtx_lock(&(mpt)->mpt_lock)
|
|
#define mpt_sleep(mpt, ident, priority, wmesg, timo) \
|
|
msleep(ident, &(mpt)->mpt_lock, priority, wmesg, timo)
|
|
|
|
#else
|
|
|
|
#define MPT_IFLAGS INTR_TYPE_CAM | INTR_ENTROPY
|
|
#define MPT_LOCK_SETUP(mpt) do { } while (0)
|
|
#define MPT_LOCK_DESTROY(mpt) do { } while (0)
|
|
#if 0
|
|
#define MPT_LOCK(mpt) \
|
|
device_printf(mpt->dev, "LOCK %s:%d\n", __FILE__, __LINE__); \
|
|
KASSERT(mpt->mpt_locksetup == 0, \
|
|
("recursive lock acquire at %s:%d", __FILE__, __LINE__)); \
|
|
mpt->mpt_locksetup = 1
|
|
#define MPT_UNLOCK(mpt) \
|
|
device_printf(mpt->dev, "UNLK %s:%d\n", __FILE__, __LINE__); \
|
|
KASSERT(mpt->mpt_locksetup == 1, \
|
|
("release unowned lock at %s:%d", __FILE__, __LINE__)); \
|
|
mpt->mpt_locksetup = 0
|
|
#else
|
|
#define MPT_LOCK(mpt) \
|
|
KASSERT(mpt->mpt_locksetup == 0, \
|
|
("recursive lock acquire at %s:%d", __FILE__, __LINE__)); \
|
|
mpt->mpt_locksetup = 1
|
|
#define MPT_UNLOCK(mpt) \
|
|
KASSERT(mpt->mpt_locksetup == 1, \
|
|
("release unowned lock at %s:%d", __FILE__, __LINE__)); \
|
|
mpt->mpt_locksetup = 0
|
|
#endif
|
|
#define MPT_OWNED(mpt) mpt->mpt_locksetup
|
|
#define MPTLOCK_2_CAMLOCK(mpt) MPT_UNLOCK(mpt)
|
|
#define CAMLOCK_2_MPTLOCK(mpt) MPT_LOCK(mpt)
|
|
|
|
static __inline int
|
|
mpt_sleep(struct mpt_softc *, void *, int, const char *, int);
|
|
|
|
static __inline int
|
|
mpt_sleep(struct mpt_softc *mpt, void *i, int p, const char *w, int t)
|
|
{
|
|
int r;
|
|
MPT_UNLOCK(mpt);
|
|
r = tsleep(i, p, w, t);
|
|
MPT_LOCK(mpt);
|
|
return (r);
|
|
}
|
|
#endif
|
|
#endif
|
|
|
|
/******************************* Register Access ******************************/
|
|
static __inline void mpt_write(struct mpt_softc *, size_t, uint32_t);
|
|
static __inline uint32_t mpt_read(struct mpt_softc *, int);
|
|
static __inline void mpt_pio_write(struct mpt_softc *, size_t, uint32_t);
|
|
static __inline uint32_t mpt_pio_read(struct mpt_softc *, int);
|
|
|
|
static __inline void
|
|
mpt_write(struct mpt_softc *mpt, size_t offset, uint32_t val)
|
|
{
|
|
bus_space_write_4(mpt->pci_st, mpt->pci_sh, offset, val);
|
|
}
|
|
|
|
static __inline uint32_t
|
|
mpt_read(struct mpt_softc *mpt, int offset)
|
|
{
|
|
return (bus_space_read_4(mpt->pci_st, mpt->pci_sh, offset));
|
|
}
|
|
|
|
/*
|
|
* Some operations (e.g. diagnostic register writes while the ARM proccessor
|
|
* is disabled), must be performed using "PCI pio" operations. On non-PCI
|
|
* busses, these operations likely map to normal register accesses.
|
|
*/
|
|
static __inline void
|
|
mpt_pio_write(struct mpt_softc *mpt, size_t offset, uint32_t val)
|
|
{
|
|
bus_space_write_4(mpt->pci_pio_st, mpt->pci_pio_sh, offset, val);
|
|
}
|
|
|
|
static __inline uint32_t
|
|
mpt_pio_read(struct mpt_softc *mpt, int offset)
|
|
{
|
|
return (bus_space_read_4(mpt->pci_pio_st, mpt->pci_pio_sh, offset));
|
|
}
|
|
/*********************** Reply Frame/Request Management ***********************/
|
|
/* Max MPT Reply we are willing to accept (must be power of 2) */
|
|
#define MPT_REPLY_SIZE 256
|
|
|
|
/*
|
|
* Must be less than 16384 in order for target mode to work
|
|
*/
|
|
#define MPT_MAX_REQUESTS(mpt) 512
|
|
#define MPT_REQUEST_AREA 512
|
|
#define MPT_SENSE_SIZE 32 /* included in MPT_REQUEST_AREA */
|
|
#define MPT_REQ_MEM_SIZE(mpt) (MPT_MAX_REQUESTS(mpt) * MPT_REQUEST_AREA)
|
|
|
|
#define MPT_CONTEXT_CB_SHIFT (16)
|
|
#define MPT_CBI(handle) (handle >> MPT_CONTEXT_CB_SHIFT)
|
|
#define MPT_CBI_TO_HID(cbi) ((cbi) << MPT_CONTEXT_CB_SHIFT)
|
|
#define MPT_CONTEXT_TO_CBI(x) \
|
|
(((x) >> MPT_CONTEXT_CB_SHIFT) & (MPT_NUM_REPLY_HANDLERS - 1))
|
|
#define MPT_CONTEXT_REQI_MASK 0xFFFF
|
|
#define MPT_CONTEXT_TO_REQI(x) ((x) & MPT_CONTEXT_REQI_MASK)
|
|
|
|
/*
|
|
* Convert a 32bit physical address returned from IOC to an
|
|
* offset into our reply frame memory or the kvm address needed
|
|
* to access the data. The returned address is only the low
|
|
* 32 bits, so mask our base physical address accordingly.
|
|
*/
|
|
#define MPT_REPLY_BADDR(x) \
|
|
(x << 1)
|
|
#define MPT_REPLY_OTOV(m, i) \
|
|
((void *)(&m->reply[i]))
|
|
|
|
#define MPT_DUMP_REPLY_FRAME(mpt, reply_frame) \
|
|
do { \
|
|
if (mpt->verbose > MPT_PRT_DEBUG) \
|
|
mpt_dump_reply_frame(mpt, reply_frame); \
|
|
} while(0)
|
|
|
|
static __inline uint32_t mpt_pop_reply_queue(struct mpt_softc *mpt);
|
|
static __inline void mpt_free_reply(struct mpt_softc *mpt, uint32_t ptr);
|
|
|
|
/*
|
|
* Give the reply buffer back to the IOC after we have
|
|
* finished processing it.
|
|
*/
|
|
static __inline void
|
|
mpt_free_reply(struct mpt_softc *mpt, uint32_t ptr)
|
|
{
|
|
mpt_write(mpt, MPT_OFFSET_REPLY_Q, ptr);
|
|
}
|
|
|
|
/* Get a reply from the IOC */
|
|
static __inline uint32_t
|
|
mpt_pop_reply_queue(struct mpt_softc *mpt)
|
|
{
|
|
return mpt_read(mpt, MPT_OFFSET_REPLY_Q);
|
|
}
|
|
|
|
void
|
|
mpt_complete_request_chain(struct mpt_softc *, struct req_queue *, u_int);
|
|
|
|
/************************** Scatter Gather Managment **************************/
|
|
/* MPT_RQSL- size of request frame, in bytes */
|
|
#define MPT_RQSL(mpt) (mpt->request_frame_size << 2)
|
|
|
|
/* MPT_NSGL- how many SG entries can fit in a request frame size */
|
|
#define MPT_NSGL(mpt) (MPT_RQSL(mpt) / sizeof (SGE_IO_UNION))
|
|
|
|
/* MPT_NRFM- how many request frames can fit in each request alloc we make */
|
|
#define MPT_NRFM(mpt) (MPT_REQUEST_AREA / MPT_RQSL(mpt))
|
|
|
|
/*
|
|
* MPT_NSGL_FIRST- # of SG elements that can fit after
|
|
* an I/O request but still within the request frame.
|
|
* Do this safely based upon SGE_IO_UNION.
|
|
*
|
|
* Note that the first element is *within* the SCSI request.
|
|
*/
|
|
#define MPT_NSGL_FIRST(mpt) \
|
|
((MPT_RQSL(mpt) - sizeof (MSG_SCSI_IO_REQUEST) + sizeof (SGE_IO_UNION)) / \
|
|
sizeof (SGE_IO_UNION))
|
|
|
|
/***************************** IOC Initialization *****************************/
|
|
int mpt_reset(struct mpt_softc *, int /*reinit*/);
|
|
|
|
/****************************** Debugging ************************************/
|
|
typedef struct mpt_decode_entry {
|
|
char *name;
|
|
u_int value;
|
|
u_int mask;
|
|
} mpt_decode_entry_t;
|
|
|
|
int mpt_decode_value(mpt_decode_entry_t *table, u_int num_entries,
|
|
const char *name, u_int value, u_int *cur_column,
|
|
u_int wrap_point);
|
|
|
|
void mpt_dump_request(struct mpt_softc *, request_t *);
|
|
|
|
enum {
|
|
MPT_PRT_ALWAYS,
|
|
MPT_PRT_FATAL,
|
|
MPT_PRT_ERROR,
|
|
MPT_PRT_WARN,
|
|
MPT_PRT_INFO,
|
|
MPT_PRT_NEGOTIATION,
|
|
MPT_PRT_DEBUG,
|
|
MPT_PRT_DEBUG1,
|
|
MPT_PRT_DEBUG2,
|
|
MPT_PRT_DEBUG3,
|
|
MPT_PRT_TRACE,
|
|
MPT_PRT_NONE=100
|
|
};
|
|
|
|
#if __FreeBSD_version > 500000
|
|
#define mpt_lprt(mpt, level, ...) \
|
|
do { \
|
|
if (level <= (mpt)->verbose) \
|
|
mpt_prt(mpt, __VA_ARGS__); \
|
|
} while (0)
|
|
|
|
#define mpt_lprtc(mpt, level, ...) \
|
|
do { \
|
|
if (level <= (mpt)->debug_level) \
|
|
mpt_prtc(mpt, __VA_ARGS__); \
|
|
} while (0)
|
|
#else
|
|
void mpt_lprt(struct mpt_softc *, int, const char *, ...)
|
|
__printflike(3, 4);
|
|
void mpt_lprtc(struct mpt_softc *, int, const char *, ...)
|
|
__printflike(3, 4);
|
|
#endif
|
|
void mpt_prt(struct mpt_softc *, const char *, ...)
|
|
__printflike(2, 3);
|
|
void mpt_prtc(struct mpt_softc *, const char *, ...)
|
|
__printflike(2, 3);
|
|
|
|
/**************************** Target Mode Related ***************************/
|
|
static __inline int mpt_cdblen(uint8_t, int);
|
|
static __inline int
|
|
mpt_cdblen(uint8_t cdb0, int maxlen)
|
|
{
|
|
int group = cdb0 >> 5;
|
|
switch (group) {
|
|
case 0:
|
|
return (6);
|
|
case 1:
|
|
return (10);
|
|
case 4:
|
|
case 5:
|
|
return (12);
|
|
default:
|
|
return (16);
|
|
}
|
|
}
|
|
#ifdef INVARIANTS
|
|
static __inline request_t * mpt_tag_2_req(struct mpt_softc *, uint32_t);
|
|
static __inline request_t *
|
|
mpt_tag_2_req(struct mpt_softc *mpt, uint32_t tag)
|
|
{
|
|
uint16_t rtg = (tag >> 18);
|
|
KASSERT(rtg < mpt->tgt_cmds_allocated, ("bad tag %d\n", tag));
|
|
KASSERT(mpt->tgt_cmd_ptrs, ("no cmd backpointer array"));
|
|
KASSERT(mpt->tgt_cmd_ptrs[rtg], ("no cmd backpointer"));
|
|
return (mpt->tgt_cmd_ptrs[rtg]);
|
|
}
|
|
|
|
|
|
static __inline int
|
|
mpt_req_on_free_list(struct mpt_softc *, request_t *);
|
|
static __inline int
|
|
mpt_req_on_pending_list(struct mpt_softc *, request_t *);
|
|
|
|
static __inline void
|
|
mpt_req_spcl(struct mpt_softc *, request_t *, const char *, int);
|
|
static __inline void
|
|
mpt_req_not_spcl(struct mpt_softc *, request_t *, const char *, int);
|
|
|
|
|
|
/*
|
|
* Is request on freelist?
|
|
*/
|
|
static __inline int
|
|
mpt_req_on_free_list(struct mpt_softc *mpt, request_t *req)
|
|
{
|
|
request_t *lrq;
|
|
|
|
TAILQ_FOREACH(lrq, &mpt->request_free_list, links) {
|
|
if (lrq == req) {
|
|
return (1);
|
|
}
|
|
}
|
|
return (0);
|
|
}
|
|
|
|
/*
|
|
* Is request on pending list?
|
|
*/
|
|
static __inline int
|
|
mpt_req_on_pending_list(struct mpt_softc *mpt, request_t *req)
|
|
{
|
|
request_t *lrq;
|
|
|
|
TAILQ_FOREACH(lrq, &mpt->request_pending_list, links) {
|
|
if (lrq == req) {
|
|
return (1);
|
|
}
|
|
}
|
|
return (0);
|
|
}
|
|
|
|
/*
|
|
* Make sure that req *is* part of one of the special lists
|
|
*/
|
|
static __inline void
|
|
mpt_req_spcl(struct mpt_softc *mpt, request_t *req, const char *s, int line)
|
|
{
|
|
int i;
|
|
for (i = 0; i < mpt->els_cmds_allocated; i++) {
|
|
if (req == mpt->els_cmd_ptrs[i]) {
|
|
return;
|
|
}
|
|
}
|
|
for (i = 0; i < mpt->tgt_cmds_allocated; i++) {
|
|
if (req == mpt->tgt_cmd_ptrs[i]) {
|
|
return;
|
|
}
|
|
}
|
|
panic("%s(%d): req %p:%u function %x not in els or tgt ptrs\n",
|
|
s, line, req, req->serno,
|
|
((PTR_MSG_REQUEST_HEADER)req->req_vbuf)->Function);
|
|
}
|
|
|
|
/*
|
|
* Make sure that req is *not* part of one of the special lists.
|
|
*/
|
|
static __inline void
|
|
mpt_req_not_spcl(struct mpt_softc *mpt, request_t *req, const char *s, int line)
|
|
{
|
|
int i;
|
|
for (i = 0; i < mpt->els_cmds_allocated; i++) {
|
|
KASSERT(req != mpt->els_cmd_ptrs[i],
|
|
("%s(%d): req %p:%u func %x in els ptrs at ioindex %d\n",
|
|
s, line, req, req->serno,
|
|
((PTR_MSG_REQUEST_HEADER)req->req_vbuf)->Function, i));
|
|
}
|
|
for (i = 0; i < mpt->tgt_cmds_allocated; i++) {
|
|
KASSERT(req != mpt->tgt_cmd_ptrs[i],
|
|
("%s(%d): req %p:%u func %x in tgt ptrs at ioindex %d\n",
|
|
s, line, req, req->serno,
|
|
((PTR_MSG_REQUEST_HEADER)req->req_vbuf)->Function, i));
|
|
}
|
|
}
|
|
#endif
|
|
|
|
typedef enum {
|
|
MPT_ABORT_TASK_SET=1234,
|
|
MPT_CLEAR_TASK_SET,
|
|
MPT_TARGET_RESET,
|
|
MPT_CLEAR_ACA,
|
|
MPT_TERMINATE_TASK,
|
|
MPT_NIL_TMT_VALUE=5678
|
|
} mpt_task_mgmt_t;
|
|
|
|
/**************************** Unclassified Routines ***************************/
|
|
void mpt_send_cmd(struct mpt_softc *mpt, request_t *req);
|
|
int mpt_recv_handshake_reply(struct mpt_softc *mpt,
|
|
size_t reply_len, void *reply);
|
|
int mpt_wait_req(struct mpt_softc *mpt, request_t *req,
|
|
mpt_req_state_t state, mpt_req_state_t mask,
|
|
int sleep_ok, int time_ms);
|
|
void mpt_enable_ints(struct mpt_softc *mpt);
|
|
void mpt_disable_ints(struct mpt_softc *mpt);
|
|
int mpt_attach(struct mpt_softc *mpt);
|
|
int mpt_shutdown(struct mpt_softc *mpt);
|
|
int mpt_detach(struct mpt_softc *mpt);
|
|
int mpt_send_handshake_cmd(struct mpt_softc *mpt,
|
|
size_t len, void *cmd);
|
|
request_t * mpt_get_request(struct mpt_softc *mpt, int sleep_ok);
|
|
void mpt_free_request(struct mpt_softc *mpt, request_t *req);
|
|
void mpt_intr(void *arg);
|
|
void mpt_check_doorbell(struct mpt_softc *mpt);
|
|
void mpt_dump_reply_frame(struct mpt_softc *mpt,
|
|
MSG_DEFAULT_REPLY *reply_frame);
|
|
|
|
void mpt_set_config_regs(struct mpt_softc *);
|
|
int mpt_issue_cfg_req(struct mpt_softc */*mpt*/, request_t */*req*/,
|
|
u_int /*Action*/, u_int /*PageVersion*/,
|
|
u_int /*PageLength*/, u_int /*PageNumber*/,
|
|
u_int /*PageType*/, uint32_t /*PageAddress*/,
|
|
bus_addr_t /*addr*/, bus_size_t/*len*/,
|
|
int /*sleep_ok*/, int /*timeout_ms*/);
|
|
int mpt_read_cfg_header(struct mpt_softc *, int /*PageType*/,
|
|
int /*PageNumber*/,
|
|
uint32_t /*PageAddress*/,
|
|
CONFIG_PAGE_HEADER *,
|
|
int /*sleep_ok*/, int /*timeout_ms*/);
|
|
int mpt_read_cfg_page(struct mpt_softc *t, int /*Action*/,
|
|
uint32_t /*PageAddress*/,
|
|
CONFIG_PAGE_HEADER *, size_t /*len*/,
|
|
int /*sleep_ok*/, int /*timeout_ms*/);
|
|
int mpt_write_cfg_page(struct mpt_softc *, int /*Action*/,
|
|
uint32_t /*PageAddress*/,
|
|
CONFIG_PAGE_HEADER *, size_t /*len*/,
|
|
int /*sleep_ok*/, int /*timeout_ms*/);
|
|
static __inline int
|
|
mpt_read_cur_cfg_page(struct mpt_softc *mpt, uint32_t PageAddress,
|
|
CONFIG_PAGE_HEADER *hdr, size_t len,
|
|
int sleep_ok, int timeout_ms)
|
|
{
|
|
return (mpt_read_cfg_page(mpt, MPI_CONFIG_ACTION_PAGE_READ_CURRENT,
|
|
PageAddress, hdr, len, sleep_ok, timeout_ms));
|
|
}
|
|
|
|
static __inline int
|
|
mpt_write_cur_cfg_page(struct mpt_softc *mpt, uint32_t PageAddress,
|
|
CONFIG_PAGE_HEADER *hdr, size_t len, int sleep_ok,
|
|
int timeout_ms)
|
|
{
|
|
return (mpt_write_cfg_page(mpt, MPI_CONFIG_ACTION_PAGE_WRITE_CURRENT,
|
|
PageAddress, hdr, len, sleep_ok,
|
|
timeout_ms));
|
|
}
|
|
|
|
/* mpt_debug.c functions */
|
|
void mpt_print_reply(void *vmsg);
|
|
void mpt_print_db(uint32_t mb);
|
|
void mpt_print_config_reply(void *vmsg);
|
|
char *mpt_ioc_diag(uint32_t diag);
|
|
void mpt_req_state(mpt_req_state_t state);
|
|
void mpt_print_config_request(void *vmsg);
|
|
void mpt_print_request(void *vmsg);
|
|
void mpt_print_scsi_io_request(MSG_SCSI_IO_REQUEST *msg);
|
|
void mpt_dump_sgl(SGE_IO_UNION *se, int offset);
|
|
#endif /* _MPT_H_ */
|