188 lines
9.2 KiB
Plaintext
188 lines
9.2 KiB
Plaintext
# This is the local configure file (distribution version).
|
|
# You must modify it to fit your particular configuration
|
|
# and name it Config.local
|
|
# The following configuratiions can be auto-generated:
|
|
#
|
|
# make Config.local.green
|
|
# make a Config.local that supports a local clock
|
|
# (i.e. allow fallback to use of the CPU's own clock)
|
|
# make Config.local.NO.clock
|
|
# make a Config.local that supports no clocks
|
|
#
|
|
#
|
|
# NOTE TO GREENHORNS
|
|
#
|
|
# For plug-'n-play and no radios or other complicated gadgetry,
|
|
# use "make Config.local.green" or "make Config.local.local" as above.
|
|
#
|
|
# Following defines can be set in the DEFS_OPT= define:
|
|
#
|
|
# The flag -DDEBUG includes some debugging code. To use this, include
|
|
# the define and start the daemon with one or more -d flags, depending
|
|
# on your calibration of pearannoya. The daemon will not detach your
|
|
# terminal in this case. Judicious use of grep will reduce the speaker
|
|
# volume to bearable levels.
|
|
#
|
|
# To change the location of the configuration file, use a
|
|
# -DCONFIG_FILE=\\"/local/etc/ntp.conf\\" or something similar.
|
|
#
|
|
# The -DSYSLOG_FILE defines allows logging messages that are normally
|
|
# reported via syslof() in a file. The file name can be configured using
|
|
# the configuration line "logfile <filename>" in CONFIG_FILE.
|
|
#
|
|
# There are three serial port system software interfaces, each of
|
|
# which is peculiar to one or more Unix versions. Define
|
|
# -DHAVE_SYSV_TTYS for basic System V compatibility; define -DSTREAM
|
|
# for POSIX compatibility including System V Streams, and
|
|
# HAVE_BSD_TTYS for 4.3bsd compatibility. Only one of these three
|
|
# should be defined. If none are defined, HAVE_BSD_TTYS is assumed.
|
|
# Usually these defines are already set correctly.
|
|
#
|
|
DEFS_OPT=-DDEBUG
|
|
#
|
|
# The DEFS_LOCAL define picks up all flags from DEFS_OPT (do not delete that)
|
|
# and one of the following:
|
|
#
|
|
# The flag -DREFCLOCK causes the basic reference clock support to be
|
|
# compiled into the daemon. If you set this you may also want to
|
|
# configure the particular clock drivers you want in the CLOCKDEFS= line
|
|
# below. This flag affects xntpd only. This define is included by
|
|
# default when using the "make makeconfig" script.
|
|
#
|
|
# The next two sets of defines are meaningful only when radio clock
|
|
# drivers or special 1-pps signals are to be used. For systems without
|
|
# these features, these delicious complexities can be avoided. Ordinarily,
|
|
# the "make makeconfig" script figures out which ones to use, but your
|
|
# mileage may vary.
|
|
#
|
|
# There are three ways to utilize external 1-pps signals. Define
|
|
# -DPPS to include just the pps routine, such as used by the DCF77(PARSE)
|
|
# clock driver. Define -DPPSCLK to include a serial device driver
|
|
# which avoids much of the jitter due to upper level port
|
|
# processing. This requires a dedicated serial port and either the
|
|
# tty_clock line discipline or tty_clk_streams module, both of
|
|
# which are in the ./kernel directory. Define -DPPSCD to include a
|
|
# special driver which intercepts carrier-detect transitions
|
|
# generated by the pps signal. This requires a nondedicated serial
|
|
# port and the ppsclock streams module in the ./kernel directory.
|
|
# Only one of these three flags should be defined.
|
|
#
|
|
# The flag KERNEL_PLL causes code to be compiled for a special feature of
|
|
# the kernel that (a) implements the phase-lock loop and (b) provides
|
|
# a user interface to learn time, maximum error and estimated error.
|
|
# See the file README.kern in the doc directory for further info.
|
|
# This code is activated only if the relevant kernel features have
|
|
# been configured; it does not affect operation of unmodified kernels.
|
|
# To compile it, however, requires a few header files from the
|
|
# special distribution.
|
|
#
|
|
# Note: following line must always start with DEFS_LOCAL= $(DEFS_OPT)
|
|
DEFS_LOCAL= $(DEFS_OPT) -DPPSPPS -DREFCLOCK -DKERNEL_PLL
|
|
#
|
|
# Radio clock support definitions (these only make sense if -DREFCLOCK
|
|
# used), which is normally the case. Note that a configuration can include
|
|
# no clocks, more than one type of clock and even multiple clocks of the
|
|
# same type.
|
|
#
|
|
# For most radio clocks operating with serial ports, accuracy can
|
|
# be considerably improved through use of the tty_clk line
|
|
# discipline or tty_clk_STREAMS streams module found in the
|
|
# ./kernel directory. These gizmos capture a timestamp upon
|
|
# occurrence of an intercept character and stuff it in the data
|
|
# stream for the clock driver to munch. To select this mode,
|
|
# postfix the driver name with the string CLK; that is, WWVB
|
|
# becomes WWVBCLK. If more than one clock is in use, the CLK
|
|
# postfix can be used with any or all of them.
|
|
#
|
|
# Alternatively, for the best accuracy, use the ppsclock streams
|
|
# module in the ./ppsclock directory to steal the carrier-detect
|
|
# transition and capture a precision timestamp. At present this
|
|
# works only with SunOS 4.1.1 or later. To select this mode,
|
|
# postfix the driver name with the string PPS; that is, AS2201
|
|
# becomes AS2201PPS. If more than one clock is in use, the PPS
|
|
# postfix should be used with only one of them. If any PPS
|
|
# postfix is defined, the -DPPSPPS define should be used on the
|
|
# DEFS above.
|
|
#
|
|
# Define -DLOCAL_CLOCK for a local pseudo-clock to masquerade as a
|
|
# reference clock for those subnets without access to the real thing.
|
|
# Works in all systems and requires no hardware support. This is defined
|
|
# by default when using the "make makeconfig" script and greenhorn
|
|
# configuraiton.
|
|
#
|
|
# Define -DPST for a PST/Traconex 1020 WWV/H receiver. The driver
|
|
# supports both the CLK and PPS modes. It should work in all systems
|
|
# with a serial port.
|
|
#
|
|
# Define -DWWVB for a Spectracom 8170 or Netclock/2 WWVB receiver. It
|
|
# should work in all systems with a serial port. The driver supports
|
|
# both the CLK and PPS modes if the requisite kernel support is installed.
|
|
#
|
|
# Define -DCHU for a special CHU receiver using an ordinary shortwave
|
|
# radio. This requires the chu_clk line discipline or chu_clk_STREAMS
|
|
# module in the ./kernel directory. At present, this driver works only
|
|
# on SunOS4.1.x; operation in other systems has not been confirmed.
|
|
# Construction details for a suitable modem can be found in the ./gadget
|
|
# directory. The driver supports # neither the CLK nor PPS modes.
|
|
#
|
|
# Define -DPARSE for a DCF77/GPS(GENERIC) receiver. For best performance
|
|
# this requires a special parsestreams STREAMS (SunOS 4.x) module in the
|
|
# ./parse directory. Define -DPARSEPPS for PPS support via the
|
|
# DCF77/GPS (GENERIC) receiver; also, define -DPPS in the DEFS above.
|
|
# Define: -DCLOCK_MEINBERG for Meinberg clocks
|
|
# -DCLOCK_SCHMID for Schmid receivers
|
|
# -DCLOCK_DCF7000 for ELV DCF7000
|
|
# -DCLOCK_RAWDCF for simple receivers (100/200ms pulses on Rx)
|
|
# -DCLOCK_TRIMSV6 for Trimble SV6 GPS receiver
|
|
#
|
|
# Define -DMX4200PPS for a Magnavox 4200 GPS receiver. At present, this
|
|
# driver works only on SunOS4.1.x with CPU serial ports only. The PPS
|
|
# mode is required.
|
|
#
|
|
# Define -DAS2201 for an Austron 2200A or 2201A GPS receiver. It should
|
|
# work in all systems with a serial port. The driver does not support the
|
|
# CLK mode, but does support the PPS mode. If the radio is connected to
|
|
# more than one machine, the PPS mode is required.
|
|
#
|
|
# Define -DGOES for a Kinemetrics/TrueTime 468-DC GOES receiver. This
|
|
# driver is known to work with some other TrueTime products as well,
|
|
# including the GPS-DC GPS receiver. It should work in all systems with
|
|
# a serial port. The driver does not support the CLK mode, but does
|
|
# support the PPS mode.
|
|
#
|
|
# Define -DOMEGA for a Kinemetrics/TrueTime OM-DC OMEGA receiver. It
|
|
# should work in all systems with a serial port. The driver does not
|
|
# support the CLK mode, but does support the PPS mode.
|
|
#
|
|
# Define -DTPRO for a KSI/Odetics TPRO-S IRIG-B timecode reader. This
|
|
# requires the SunOS interface driver available from KSI. The driver
|
|
# supports neither the CLK nor PPS modes.
|
|
#
|
|
# Define -DLEITCH for a Leitch CSD 5300 Master Clock System Driver for
|
|
# the HP 5061B Cesium Clock. It should work in all systems with a serial
|
|
# port. The driver does not support the CLK mode, but does support the
|
|
# PPS mode.
|
|
#
|
|
# Define -DMSFEESPPS for an EES M201 MSF receiver. It currently only works
|
|
# under SunOS 4.x with the PPSCD (ppsclock) STREAMS module, but the RCS
|
|
# files on cl.cam.ac.uk still has support for CLK and CBREAK modes.
|
|
#
|
|
# Define -DIRIG for a IRIG-B timecode timecode using the audio codec of
|
|
# the Sun SPARCstations. This requires a modified BSD audio driver and
|
|
# exclusive access to the audio port. A memo describing how it works and
|
|
# how to install the driver is in the README.irig file in the ./doc
|
|
# directory.
|
|
#
|
|
# Note: The following defines result in compilation of all the above radio
|
|
# clocks. This works on a Sun 4.1.x system which has tty_clk, chu_clk and
|
|
# ppsclock STREAMS modules installed. If the trailing CLK and PPS suffixes
|
|
# are removed and the IRIG, PARSE* and CLOCK* deleted, all of the rest compile
|
|
# under Ultrix 4.2a/3. If the MX4200 is removed, all the rest compile on a DEC
|
|
# OSF/1 Alpha.
|
|
#
|
|
CLOCKDEFS=-DAS2201PPS -DCHU -DGOES -DIRIG -DLEITCH -DLOCAL_CLOCK -DMX4200PPS -DOMEGA -DPSTCLK -DTPRO -DWWVBCLK
|
|
#
|
|
# Directory into which binaries should be installed (default /usr/local)
|
|
#
|
|
BINDIR= /usr/local/bin
|