71d51719ea
Differential Revision: https://reviews.freebsd.org/D2372 Reviewed by: jhb, wblock, adrian Approved by: jhb, wblock Relnotes: yes
623 lines
23 KiB
C
623 lines
23 KiB
C
/*
|
|
* Copyright (c) 2014 The DragonFly Project. All rights reserved.
|
|
*
|
|
* This code is derived from software contributed to The DragonFly Project
|
|
* by Matthew Dillon <dillon@backplane.com> and was subsequently ported
|
|
* to FreeBSD by Michael Gmelin <freebsd@grem.de>
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
*
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in
|
|
* the documentation and/or other materials provided with the
|
|
* distribution.
|
|
* 3. Neither the name of The DragonFly Project nor the names of its
|
|
* contributors may be used to endorse or promote products derived
|
|
* from this software without specific, prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
|
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
|
* COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
|
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
|
|
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
|
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
|
|
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
|
|
* OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGE.
|
|
*
|
|
* $FreeBSD$
|
|
*/
|
|
/*
|
|
* Intel fourth generation mobile cpus integrated I2C device.
|
|
*
|
|
* Datasheet reference: Section 22.
|
|
*
|
|
* http://www.intel.com/content/www/us/en/processors/core/4th-gen-core-family-mobile-i-o-datasheet.html?wapkw=datasheets+4th+generation
|
|
*
|
|
* This is a from-scratch driver under the BSD license using the Intel data
|
|
* sheet and the linux driver for reference. All code is freshly written
|
|
* without referencing the linux driver code. However, during testing
|
|
* I am also using the linux driver code as a reference to help resolve any
|
|
* issues that come. These will be specifically documented in the code.
|
|
*
|
|
* Please see protocol notes in section 5.21. This controller is an I2C
|
|
* master only and cannot act as a slave. The IO voltage should be set by
|
|
* the BIOS. Standard (100Kb/s) and Fast (400Kb/s) and fast mode plus
|
|
* (1MB/s) is supported. High speed mode (3.4 MB/s) is NOT supported.
|
|
*/
|
|
|
|
#ifndef _BUS_SMBUS_INTELGEN4_IG4_REG_H_
|
|
#define _BUS_SMBUS_INTELGEN4_IG4_REG_H_
|
|
|
|
/*
|
|
* 22.2 MMIO registers can be accessed through BAR0 in PCI mode or through
|
|
* BAR1 when in ACPI mode.
|
|
*
|
|
* Register width is 32-bits
|
|
*
|
|
* 22.2 Default Values on device reset are 0 except as specified here:
|
|
* TAR_ADD 0x00000055
|
|
* SS_SCL_HCNT 0x00000264
|
|
* SS_SCL_LCNT 0x000002C2
|
|
* FS_SCL_HCNT 0x0000006E
|
|
* FS_SCL_LCNT 0x000000CF
|
|
* INTR_MASK 0x000008FF
|
|
* I2C_STA 0x00000006
|
|
* SDA_HOLD 0x00000001
|
|
* SDA_SETUP 0x00000064
|
|
* COMP_PARAM1 0x00FFFF6E
|
|
* COMP_VER 0x3131352A
|
|
*/
|
|
|
|
#define IG4_REG_CTL 0x0000 /* RW Control Register */
|
|
#define IG4_REG_TAR_ADD 0x0004 /* RW Target Address */
|
|
#define IG4_REG_DATA_CMD 0x0010 /* RW Data Buffer and Command */
|
|
#define IG4_REG_SS_SCL_HCNT 0x0014 /* RW Std Speed clock High Count */
|
|
#define IG4_REG_SS_SCL_LCNT 0x0018 /* RW Std Speed clock Low Count */
|
|
#define IG4_REG_FS_SCL_HCNT 0x001C /* RW Fast Speed clock High Count */
|
|
#define IG4_REG_FS_SCL_LCNT 0x0020 /* RW Fast Speed clock Low Count */
|
|
#define IG4_REG_INTR_STAT 0x002C /* RO Interrupt Status */
|
|
#define IG4_REG_INTR_MASK 0x0030 /* RW Interrupt Mask */
|
|
#define IG4_REG_RAW_INTR_STAT 0x0034 /* RO Raw Interrupt Status */
|
|
#define IG4_REG_RX_TL 0x0038 /* RW Receive FIFO Threshold */
|
|
#define IG4_REG_TX_TL 0x003C /* RW Transmit FIFO Threshold */
|
|
#define IG4_REG_CLR_INTR 0x0040 /* RO Clear Interrupt */
|
|
#define IG4_REG_CLR_RX_UNDER 0x0044 /* RO Clear RX_Under Interrupt */
|
|
#define IG4_REG_CLR_RX_OVER 0x0048 /* RO Clear RX_Over Interrupt */
|
|
#define IG4_REG_CLR_TX_OVER 0x004C /* RO Clear TX_Over Interrupt */
|
|
#define IG4_REG_CLR_TX_ABORT 0x0054 /* RO Clear TX_Abort Interrupt */
|
|
#define IG4_REG_CLR_ACTIVITY 0x005C /* RO Clear Activity Interrupt */
|
|
#define IG4_REG_CLR_STOP_DET 0x0060 /* RO Clear STOP Detection Int */
|
|
#define IG4_REG_CLR_START_DET 0x0064 /* RO Clear START Detection Int */
|
|
#define IG4_REG_CLR_GEN_CALL 0x0068 /* RO Clear General Call Interrupt */
|
|
#define IG4_REG_I2C_EN 0x006C /* RW I2C Enable */
|
|
#define IG4_REG_I2C_STA 0x0070 /* RO I2C Status */
|
|
#define IG4_REG_TXFLR 0x0074 /* RO Transmit FIFO Level */
|
|
#define IG4_REG_RXFLR 0x0078 /* RO Receive FIFO Level */
|
|
#define IG4_REG_SDA_HOLD 0x007C /* RW SDA Hold Time Length */
|
|
#define IG4_REG_TX_ABRT_SOURCE 0x0080 /* RO Transmit Abort Source */
|
|
#define IG4_REG_SLV_DATA_NACK 0x0084 /* RW General Slave Data NACK */
|
|
#define IG4_REG_DMA_CTRL 0x0088 /* RW DMA Control */
|
|
#define IG4_REG_DMA_TDLR 0x008C /* RW DMA Transmit Data Level */
|
|
#define IG4_REG_DMA_RDLR 0x0090 /* RW DMA Receive Data Level */
|
|
#define IG4_REG_SDA_SETUP 0x0094 /* RW SDA Setup */
|
|
#define IG4_REG_ENABLE_STATUS 0x009C /* RO Enable Status */
|
|
#define IG4_REG_COMP_PARAM1 0x00F4 /* RO Component Parameter */
|
|
#define IG4_REG_COMP_VER 0x00F8 /* RO Component Version */
|
|
#define IG4_REG_COMP_TYPE 0x00FC /* RO Probe width/endian? (linux) */
|
|
#define IG4_REG_CLK_PARMS 0x0800 /* RW Clock Parameters */
|
|
#define IG4_REG_RESETS 0x0804 /* RW Reset Register */
|
|
#define IG4_REG_GENERAL 0x0808 /* RW General Register */
|
|
#define IG4_REG_SW_LTR_VALUE 0x0810 /* RW SW LTR Value */
|
|
#define IG4_REG_AUTO_LTR_VALUE 0x0814 /* RW Auto LTR Value */
|
|
|
|
/*
|
|
* CTL - Control Register 22.2.1
|
|
* Default Value: 0x0000007F.
|
|
*
|
|
* RESTARTEN - RW Restart Enable
|
|
* 10BIT - RW Controller operates in 10-bit mode, else 7-bit
|
|
*
|
|
* NOTE: When restart is disabled the controller is incapable of
|
|
* performing the following functions:
|
|
*
|
|
* Sending a START Byte
|
|
* Performing any high-speed mode op
|
|
* Performing direction changes in combined format mode
|
|
* Performing a read operation with a 10-bit address
|
|
*
|
|
* Attempting to perform the above operations will result in the
|
|
* TX_ABORT bit being set in RAW_INTR_STAT.
|
|
*/
|
|
#define IG4_CTL_SLAVE_DISABLE 0x0040 /* snarfed from linux */
|
|
#define IG4_CTL_RESTARTEN 0x0020 /* Allow Restart when master */
|
|
#define IG4_CTL_10BIT 0x0010 /* ctlr accepts 10-bit addresses */
|
|
#define IG4_CTL_SPEED_FAST 0x0004 /* snarfed from linux */
|
|
#define IG4_CTL_SPEED_STD 0x0002 /* snarfed from linux */
|
|
#define IG4_CTL_MASTER 0x0001 /* snarfed from linux */
|
|
|
|
/*
|
|
* TAR_ADD - Target Address Register 22.2.2
|
|
* Default Value: 0x00000055F
|
|
*
|
|
* 10BIT - RW controller starts its transfers in 10-bit
|
|
* address mode, else 7-bit.
|
|
*
|
|
* SPECIAL - RW Indicates whether software performs a General Call
|
|
* or START BYTE command.
|
|
*
|
|
* 0 Ignore GC_OR_START and use TAR address.
|
|
*
|
|
* 1 Perform special I2C Command based on GC_OR_START.
|
|
*
|
|
* GC_OR_START - RW (only if SPECIAL is set)
|
|
*
|
|
* 0 General Call Address. After issuing a General Call,
|
|
* only writes may be performed. Attempting to issue
|
|
* a read command results in IX_ABRT in RAW_INTR_STAT.
|
|
* The controller remains in General Call mode until
|
|
* bit 11 (SPECIAL) is cleared.
|
|
*
|
|
* 1 START BYTE.
|
|
*
|
|
*
|
|
* IC_TAR - RW when transmitting a general call, these bits are
|
|
* ignored. To generate a START BYTE, the address
|
|
* needs to be written into these bits once.
|
|
*
|
|
* This register should only be updated when the IIC is disabled (I2C_ENABLE=0)
|
|
*/
|
|
#define IG4_TAR_10BIT 0x1000 /* start xfer in 10-bit mode */
|
|
#define IG4_TAR_SPECIAL 0x0800 /* Perform special command */
|
|
#define IG4_TAR_GC_OR_START 0x0400 /* General Call or Start */
|
|
#define IG4_TAR_ADDR_MASK 0x03FF /* Target address */
|
|
|
|
/*
|
|
* TAR_DATA_CMD - Data Buffer and Command Register 22.2.3
|
|
*
|
|
* RESTART - RW This bit controls whether a forced RESTART is
|
|
* issued before the byte is sent or received.
|
|
*
|
|
* 0 If not set a RESTART is only issued if the tranfer
|
|
* direction is changing from the previous command.
|
|
*
|
|
* 1 A RESTART is issued before the byte is sent or
|
|
* received, regardless of whether or not the transfer
|
|
* direction is changing from the previous command.
|
|
*
|
|
* STOP - RW This bit controls whether a STOP is issued after
|
|
* the byte is sent or received.
|
|
*
|
|
* 0 STOP is not issued after this byte, regardless
|
|
* of whether or not the Tx FIFO is empty.
|
|
*
|
|
* 1 STOP is issued after this byte, regardless of
|
|
* whether or not the Tx FIFO is empty. If the
|
|
* Tx FIFO is not empty the master immediately tries
|
|
* to start a new transfer by issuing a START and
|
|
* arbitrating for the bus.
|
|
*
|
|
* i.e. the STOP is issued along with this byte,
|
|
* within the write stream.
|
|
*
|
|
* COMMAND - RW Control whether a read or write is performed.
|
|
*
|
|
* 0 WRITE
|
|
*
|
|
* 1 READ
|
|
*
|
|
* DATA (7:0) - RW Contains the data to be transmitted or received
|
|
* on the I2C bus.
|
|
*
|
|
* NOTE: Writing to this register causes a START + slave + RW to be
|
|
* issued if the direction has changed or the last data byte was
|
|
* sent with a STOP.
|
|
*
|
|
* NOTE: We control termination? so this register must be written
|
|
* for each byte we wish to receive. We can then drain the
|
|
* receive FIFO.
|
|
*/
|
|
|
|
#define IG4_DATA_RESTART 0x0400 /* Force RESTART */
|
|
#define IG4_DATA_STOP 0x0200 /* Force STOP[+START] */
|
|
#define IG4_DATA_COMMAND_RD 0x0100 /* bus direction 0=write 1=read */
|
|
#define IG4_DATA_MASK 0x00FF
|
|
|
|
/*
|
|
* SS_SCL_HCNT - Standard Speed Clock High Count Register 22.2.4
|
|
* SS_SCL_LCNT - Standard Speed Clock Low Count Register 22.2.5
|
|
* FS_SCL_HCNT - Fast Speed Clock High Count Register 22.2.6
|
|
* FS_SCL_LCNT - Fast Speed Clock Low Count Register 22.2.7
|
|
*
|
|
* COUNT (15:0) - Set the period count to a value between 6 and
|
|
* 65525.
|
|
*/
|
|
#define IG4_SCL_CLOCK_MASK 0xFFFFU /* count bits in register */
|
|
|
|
/*
|
|
* INTR_STAT - (RO) Interrupt Status Register 22.2.8
|
|
* INTR_MASK - (RW) Interrupt Mask Register 22.2.9
|
|
* RAW_INTR_STAT- (RO) Raw Interrupt Status Register 22.2.10
|
|
*
|
|
* GEN_CALL Set only when a general call (broadcast) address
|
|
* is received and acknowleged, stays set until
|
|
* cleared by reading CLR_GEN_CALL.
|
|
*
|
|
* START_DET Set when a START or RESTART condition has occurred
|
|
* on the interface.
|
|
*
|
|
* STOP_DET Set when a STOP condition has occurred on the
|
|
* interface.
|
|
*
|
|
* ACTIVITY Set by any activity on the interface. Cleared
|
|
* by reading CLR_ACTIVITY or CLR_INTR.
|
|
*
|
|
* TX_ABRT Indicates the controller as a transmitter is
|
|
* unable to complete the intended action. When set,
|
|
* the controller will hold the TX FIFO in a reset
|
|
* state (flushed) until CLR_TX_ABORT is read to
|
|
* clear the condition. Once cleared, the TX FIFO
|
|
* will be available again.
|
|
*
|
|
* TX_EMPTY Indicates that the transmitter is at or below
|
|
* the specified TX_TL threshold. Automatically
|
|
* cleared by HW when the buffer level goes above
|
|
* the threshold.
|
|
*
|
|
* TX_OVER Indicates that the processer attempted to write
|
|
* to the TX FIFO while the TX FIFO was full. Cleared
|
|
* by reading CLR_TX_OVER.
|
|
*
|
|
* RX_FULL Indicates that the receive FIFO has reached or
|
|
* exceeded the specified RX_TL threshold. Cleared
|
|
* by HW when the cpu drains the FIFO to below the
|
|
* threshold.
|
|
*
|
|
* RX_OVER Indicates that the receive FIFO was unable to
|
|
* accept new data and data was lost. Cleared by
|
|
* reading CLR_RX_OVER.
|
|
*
|
|
* RX_UNDER Indicates that the cpu attempted to read data
|
|
* from the receive buffer while the RX FIFO was
|
|
* empty. Cleared by reading CLR_RX_UNDER.
|
|
*
|
|
* NOTES ON RAW_INTR_STAT:
|
|
*
|
|
* This register can be used to monitor the GEN_CALL, START_DET,
|
|
* STOP_DET, ACTIVITY, TX_ABRT, TX_EMPTY, TX_OVER, RX_FULL, RX_OVER,
|
|
* and RX_UNDER bits. The documentation is a bit unclear but presumably
|
|
* this is the unlatched version.
|
|
*
|
|
* Code should test FIFO conditions using the I2C_STA (status) register,
|
|
* not the interrupt status registers.
|
|
*/
|
|
|
|
#define IG4_INTR_GEN_CALL 0x0800
|
|
#define IG4_INTR_START_DET 0x0400
|
|
#define IG4_INTR_STOP_DET 0x0200
|
|
#define IG4_INTR_ACTIVITY 0x0100
|
|
#define IG4_INTR_TX_ABRT 0x0040
|
|
#define IG4_INTR_TX_EMPTY 0x0010
|
|
#define IG4_INTR_TX_OVER 0x0008
|
|
#define IG4_INTR_RX_FULL 0x0004
|
|
#define IG4_INTR_RX_OVER 0x0002
|
|
#define IG4_INTR_RX_UNDER 0x0001
|
|
|
|
/*
|
|
* RX_TL - (RW) Receive FIFO Threshold Register 22.2.11
|
|
* TX_TL - (RW) Transmit FIFO Threshold Register 22.2.12
|
|
*
|
|
* Specify the receive and transmit FIFO threshold register. The
|
|
* FIFOs have 16 elements. The valid range is 0-15. Setting a
|
|
* value greater than 15 causes the actual value to be the maximum
|
|
* depth of the FIFO.
|
|
*
|
|
* Generally speaking since everything is messaged, we can use a
|
|
* mid-level setting for both parameters and (e.g.) fully drain the
|
|
* receive FIFO on the STOP_DET condition to handle loose ends.
|
|
*/
|
|
#define IG4_FIFO_MASK 0x00FF
|
|
#define IG4_FIFO_LIMIT 16
|
|
|
|
/*
|
|
* CLR_INTR - (RO) Clear Interrupt Register 22.2.13
|
|
* CLR_RX_UNDER - (RO) Clear Interrupt Register (specific) 22.2.14
|
|
* CLR_RX_OVER - (RO) Clear Interrupt Register (specific) 22.2.15
|
|
* CLR_TX_OVER - (RO) Clear Interrupt Register (specific) 22.2.16
|
|
* CLR_TX_ABORT - (RO) Clear Interrupt Register (specific) 22.2.17
|
|
* CLR_ACTIVITY - (RO) Clear Interrupt Register (specific) 22.2.18
|
|
* CLR_STOP_DET - (RO) Clear Interrupt Register (specific) 22.2.19
|
|
* CLR_START_DET- (RO) Clear Interrupt Register (specific) 22.2.20
|
|
* CLR_GEN_CALL - (RO) Clear Interrupt Register (specific) 22.2.21
|
|
*
|
|
* CLR_* specific operations clear the appropriate bit in the
|
|
* RAW_INTR_STAT register. Intel does not really document whether
|
|
* these operations clear the normal interrupt status register.
|
|
*
|
|
* CLR_INTR clears bits in the normal interrupt status register and
|
|
* presumably also the raw(?) register? Intel is again unclear.
|
|
*
|
|
* NOTE: CLR_INTR only clears software-clearable interrupts. Hardware
|
|
* clearable interrupts are controlled entirely by the hardware.
|
|
* CLR_INTR also clears the TX_ABRT_SOURCE register.
|
|
*
|
|
* NOTE: CLR_TX_ABORT also clears the TX_ABRT_SOURCE register and releases
|
|
* the TX FIFO from its flushed/reset state, allowing more writes
|
|
* to the TX FIFO.
|
|
*
|
|
* NOTE: CLR_ACTIVITY has no effect if the I2C bus is still active.
|
|
* Intel documents that the bit is automatically cleared when
|
|
* there is no further activity on the bus.
|
|
*/
|
|
#define IG4_CLR_BIT 0x0001 /* Reflects source */
|
|
|
|
/*
|
|
* I2C_EN - (RW) I2C Enable Register 22.2.22
|
|
*
|
|
* ABORT Software can abort an I2C transfer by setting this
|
|
* bit. Hardware will clear the bit once the STOP has
|
|
* been detected. This bit can only be set while the
|
|
* I2C interface is enabled.
|
|
*
|
|
* I2C_ENABLE Enable the controller, else disable it.
|
|
* (Use I2C_ENABLE_STATUS to poll enable status
|
|
* & wait for changes)
|
|
*/
|
|
#define IG4_I2C_ABORT 0x0002
|
|
#define IG4_I2C_ENABLE 0x0001
|
|
|
|
/*
|
|
* I2C_STA - (RO) I2C Status Register 22.2.23
|
|
*/
|
|
#define IG4_STATUS_ACTIVITY 0x0020 /* Controller is active */
|
|
#define IG4_STATUS_RX_FULL 0x0010 /* RX FIFO completely full */
|
|
#define IG4_STATUS_RX_NOTEMPTY 0x0008 /* RX FIFO not empty */
|
|
#define IG4_STATUS_TX_EMPTY 0x0004 /* TX FIFO completely empty */
|
|
#define IG4_STATUS_TX_NOTFULL 0x0002 /* TX FIFO not full */
|
|
#define IG4_STATUS_I2C_ACTIVE 0x0001 /* I2C bus is active */
|
|
|
|
/*
|
|
* TXFLR - (RO) Transmit FIFO Level Register 22.2.24
|
|
* RXFLR - (RO) Receive FIFO Level Register 22.2.25
|
|
*
|
|
* Read the number of entries currently in the Transmit or Receive
|
|
* FIFOs. Note that for some reason the mask is 9 bits instead of
|
|
* the 8 bits the fill level controls.
|
|
*/
|
|
#define IG4_FIFOLVL_MASK 0x001F
|
|
|
|
/*
|
|
* SDA_HOLD - (RW) SDA Hold Time Length Register 22.2.26
|
|
*
|
|
* Set the SDA hold time length register in I2C clocks.
|
|
*/
|
|
#define IG4_SDA_HOLD_MASK 0x00FF
|
|
|
|
/*
|
|
* TX_ABRT_SOURCE- (RO) Transmit Abort Source Register 22.2.27
|
|
*
|
|
* Indicates the cause of a transmit abort. This can indicate a
|
|
* software programming error or a device expected address width
|
|
* mismatch or other issues. The NORESTART conditions and GENCALL_NOACK
|
|
* can only occur if a programming error was made in the driver software.
|
|
*
|
|
* In particular, it should be possible to detect whether any devices
|
|
* are on the bus by observing the GENCALL_READ status, and it might
|
|
* be possible to detect ADDR7 vs ADDR10 mismatches.
|
|
*/
|
|
#define IG4_ABRTSRC_TRANSFER 0x00010000 /* Abort initiated by user */
|
|
#define IG4_ABRTSRC_ARBLOST 0x00001000 /* Arbitration lost */
|
|
#define IG4_ABRTSRC_NORESTART_10 0x00000400 /* RESTART disabled */
|
|
#define IG4_ABRTSRC_NORESTART_START 0x00000200 /* RESTART disabled */
|
|
#define IG4_ABRTSRC_ACKED_START 0x00000080 /* Improper acked START */
|
|
#define IG4_ABRTSRC_GENCALL_NOACK 0x00000020 /* Improper GENCALL */
|
|
#define IG4_ABRTSRC_GENCALL_READ 0x00000010 /* Nobody acked GENCALL */
|
|
#define IG4_ABRTSRC_TXNOACK_DATA 0x00000008 /* data phase no ACK */
|
|
#define IG4_ABRTSRC_TXNOACK_ADDR10_2 0x00000004 /* addr10/1 phase no ACK */
|
|
#define IG4_ABRTSRC_TXNOACK_ADDR10_1 0x00000002 /* addr10/2 phase no ACK */
|
|
#define IG4_ABRTSRC_TXNOACK_ADDR7 0x00000001 /* addr7 phase no ACK */
|
|
|
|
/*
|
|
* SLV_DATA_NACK - (RW) Generate Slave DATA NACK Register 22.2.28
|
|
*
|
|
* When the controller is a receiver a NACK can be generated on
|
|
* receipt of data.
|
|
*
|
|
* NACK_GENERATE Set to 0 for normal NACK/ACK generation.
|
|
* Set to 1 to generate a NACK after next data
|
|
* byte received.
|
|
*
|
|
*/
|
|
#define IG4_NACK_GENERATE 0x0001
|
|
|
|
/*
|
|
* DMA_CTRL - (RW) DMA Control Register 22.2.29
|
|
*
|
|
* Enables DMA on the transmit and/or receive DMA channel.
|
|
*/
|
|
#define IG4_TX_DMA_ENABLE 0x0002
|
|
#define IG4_RX_DMA_ENABLE 0x0001
|
|
|
|
/*
|
|
* DMA_TDLR - (RW) DMA Transmit Data Level Register 22.2.30
|
|
* DMA_RDLR - (RW) DMA Receive Data Level Register 22.2.31
|
|
*
|
|
* Similar to RX_TL and TX_TL but controls when a DMA burst occurs
|
|
* to empty or fill the FIFOs. Use the same IG4_FIFO_MASK and
|
|
* IG4_FIFO_LIMIT defines for RX_RL and TX_TL.
|
|
*/
|
|
/* empty */
|
|
|
|
/*
|
|
* SDA_SETUP - (RW) SDA Setup Time Length Register 22.2.32
|
|
*
|
|
* Set the SDA setup time length register in I2C clocks.
|
|
* The register must be programmed with a value >=2.
|
|
* (Defaults to 0x64).
|
|
*/
|
|
#define IG4_SDA_SETUP_MASK 0x00FF
|
|
|
|
/*
|
|
* ACK_GEN_CALL - (RW) ACK General Call Register 22.2.33
|
|
*
|
|
* Control whether the controller responds with a ACK or NACK when
|
|
* it receives an I2C General Call address.
|
|
*
|
|
* If set to 0 a NACK is generated and a General Call interrupt is
|
|
* NOT generated. Otherwise an ACK + interrupt is generated.
|
|
*/
|
|
#define IG4_ACKGC_ACK 0x0001
|
|
|
|
/*
|
|
* ENABLE_STATUS - (RO) Enable Status Registger 22.2.34
|
|
*
|
|
* DATA_LOST - Indicates that a slave receiver operation has
|
|
* been aborted with at least one data byte received
|
|
* from a transfer due to the I2C controller being
|
|
* disabled (IG4_I2C_ENABLE -> 0)
|
|
*
|
|
* ENABLED - Intel documentation is lacking but I assume this
|
|
* is a reflection of the IG4_I2C_ENABLE bit in the
|
|
* I2C_EN register.
|
|
*
|
|
*/
|
|
#define IG4_ENASTAT_DATA_LOST 0x0004
|
|
#define IG4_ENASTAT_ENABLED 0x0001
|
|
|
|
/*
|
|
* COMP_PARAM1 - (RO) Component Parameter Register 22.2.35
|
|
* Default Value 0x00FFFF6E
|
|
*
|
|
* VALID - Intel documentation is unclear but I believe this
|
|
* must be read as a 1 to indicate that the rest of
|
|
* the bits in the register are valid.
|
|
*
|
|
* HASDMA - Indicates that the chip is DMA-capable. Presumably
|
|
* in certain virtualization cases the chip might be
|
|
* set to not be DMA-capable.
|
|
*
|
|
* INTR_IO - Indicates that all interrupts are combined to
|
|
* generate one interrupt. If not set, interrupts
|
|
* are individual (more virtualization stuff?)
|
|
*
|
|
* HCCNT_RO - Indicates that the clock timing registers are
|
|
* RW. If not set, the registers are RO.
|
|
* (more virtualization stuff).
|
|
*
|
|
* MAXSPEED - Indicates the maximum speed supported.
|
|
*
|
|
* DATAW - Indicates the internal bus width in bits.
|
|
*/
|
|
#define IG4_PARAM1_TXFIFO_DEPTH(v) (((v) >> 16) & 0xFF)
|
|
#define IG4_PARAM1_RXFIFO_DEPTH(v) (((v) >> 8) & 0xFF)
|
|
#define IG4_PARAM1_CONFIG_VALID 0x00000080
|
|
#define IG4_PARAM1_CONFIG_HASDMA 0x00000040
|
|
#define IG4_PARAM1_CONFIG_INTR_IO 0x00000020
|
|
#define IG4_PARAM1_CONFIG_HCCNT_RO 0x00000010
|
|
#define IG4_PARAM1_CONFIG_MAXSPEED_MASK 0x0000000C
|
|
#define IG4_PARAM1_CONFIG_DATAW_MASK 0x00000003
|
|
|
|
#define IG4_CONFIG_MAXSPEED_RESERVED00 0x00000000
|
|
#define IG4_CONFIG_MAXSPEED_STANDARD 0x00000004
|
|
#define IG4_CONFIG_MAXSPEED_FAST 0x00000008
|
|
#define IG4_CONFIG_MAXSPEED_HIGH 0x0000000C
|
|
|
|
#define IG4_CONFIG_DATAW_8 0x00000000
|
|
#define IG4_CONFIG_DATAW_16 0x00000001
|
|
#define IG4_CONFIG_DATAW_32 0x00000002
|
|
#define IG4_CONFIG_DATAW_RESERVED11 0x00000003
|
|
|
|
/*
|
|
* COMP_VER - (RO) Component Version Register 22.2.36
|
|
* Default Value 0x3131352A
|
|
*
|
|
* Contains the chip version number. All 32 bits.
|
|
*/
|
|
#define IG4_COMP_VER 0x3131352A
|
|
|
|
/*
|
|
* COMP_TYPE - (RO) (linux) Endian and bus width probe
|
|
*
|
|
* Read32 from this register and test against IG4_COMP_TYPE
|
|
* to determine the bus width. e.g. 01404457 = endian-reversed,
|
|
* and 00000140 or 00004457 means internal 16-bit bus (?).
|
|
*
|
|
* This register is not in the intel documentation, I pulled it
|
|
* from the linux driver i2c-designware-core.c.
|
|
*/
|
|
#define IG4_COMP_TYPE 0x44570140
|
|
|
|
/*
|
|
* RESETS - (RW) Resets Register 22.2.37
|
|
*
|
|
* Used to reset the I2C host controller by SW. There is no timing
|
|
* requirement, software can assert and de-assert in back-to-back
|
|
* transactions.
|
|
*
|
|
* 00 I2C host controller is NOT in reset.
|
|
* 01 (reserved)
|
|
* 10 (reserved)
|
|
* 11 I2C host controller is in reset.
|
|
*/
|
|
#define IG4_RESETS_ASSERT 0x0003
|
|
#define IG4_RESETS_DEASSERT 0x0000
|
|
|
|
/*
|
|
* GENERAL - (RW) General Reigster 22.2.38
|
|
*
|
|
* IOVOLT 0=1.8V 1=3.3V
|
|
*
|
|
* LTR 0=Auto 1=SW
|
|
*
|
|
* In Auto mode the BIOS will write to the host controller's
|
|
* AUTO LTR Value register (offset 0x0814) with the active
|
|
* state LTR value, and will write to the SW LTR Value register
|
|
* (offset 0x0810) with the idle state LTR value.
|
|
*
|
|
* In SW mode the SW will write to the host controller SW LTR
|
|
* value (offset 0x0810). It is the SW responsibility to update
|
|
* the LTR with the appropriate value.
|
|
*/
|
|
#define IG4_GENERAL_IOVOLT3_3 0x0008
|
|
#define IG4_GENERAL_SWMODE 0x0004
|
|
|
|
/*
|
|
* SW_LTR_VALUE - (RW) SW LTR Value Register 22.2.39
|
|
* AUTO_LTR_VALUE - (RW) SW LTR Value Register 22.2.40
|
|
*
|
|
* Default value is 0x00000800 which means the best possible
|
|
* service/response time.
|
|
*
|
|
* It isn't quite clear how the snooping works. There are two scale
|
|
* bits for both sets but two of the four codes are reserved. The
|
|
* *SNOOP_VALUE() is specified as a 10-bit latency value. If 0, it
|
|
* indicates that the device cannot tolerate any delay and needs the
|
|
* best possible service/response time.
|
|
*
|
|
* I think this is for snooping (testing) the I2C bus. The lowest
|
|
* delay (0) probably runs the controller polling at a high, power hungry
|
|
* rate. But I dunno.
|
|
*/
|
|
#define IG4_SWLTR_NSNOOP_REQ 0x80000000 /* (ro) */
|
|
#define IG4_SWLTR_NSNOOP_SCALE_MASK 0x1C000000 /* (ro) */
|
|
#define IG4_SWLTR_NSNOOP_SCALE_1US 0x08000000 /* (ro) */
|
|
#define IG4_SWLTR_NSNOOP_SCALE_32US 0x0C000000 /* (ro) */
|
|
#define IG4_SWLTR_NSNOOP_VALUE_DECODE(v) (((v) >> 16) & 0x3F)
|
|
#define IG4_SWLTR_NSNOOP_VALUE_ENCODE(v) (((v) & 0x3F) << 16)
|
|
|
|
#define IG4_SWLTR_SNOOP_REQ 0x00008000 /* (rw) */
|
|
#define IG4_SWLTR_SNOOP_SCALE_MASK 0x00001C00 /* (rw) */
|
|
#define IG4_SWLTR_SNOOP_SCALE_1US 0x00000800 /* (rw) */
|
|
#define IG4_SWLTR_SNOOP_SCALE_32US 0x00000C00 /* (rw) */
|
|
#define IG4_SWLTR_SNOOP_VALUE_DECODE(v) ((v) & 0x3F)
|
|
#define IG4_SWLTR_SNOOP_VALUE_ENCODE(v) ((v) & 0x3F)
|
|
|
|
#endif
|