158 lines
7.3 KiB
Plaintext
158 lines
7.3 KiB
Plaintext
#
|
|
# NTP configuration file (ntp.conf)
|
|
# grundoon.udel.edu (128.4.2.7)
|
|
#
|
|
# This machine can best be described as the kitchen sink. It has, in
|
|
# addition to the baseboard tty ports ttya and ttyb, an 8-line
|
|
# Serial/Parallel Interface (SPIF) with ports ttyz00 through ttyz07. The
|
|
# configuration includes the following drivers, clock addresses and Unix
|
|
# device names.
|
|
#
|
|
# Local Clock 127.127.1.0 /dev/audio
|
|
# PST 1020 WWV/WWVH Receiver 127.127.3.1 /dev/pst1
|
|
# Spectracom 8170 WWVB Receiver 127.127.4.1 /dev/wwvb1
|
|
# IRIG Audio Decoder 127.127.6.0 /dev/audio
|
|
# Scratchbuilt CHU Receiver 127.127.7.1 /dev/chu1
|
|
# NIST ACTS modem 127.127.18.1 /dev/acts1
|
|
# Heath GC-1000 WWV Receiver 127.127.19.1 /dev/pst1
|
|
# PPS Clock 127.127.22.1 none
|
|
#
|
|
# This machine has the kernel modifications described in the README.kern
|
|
# file, as well as the tty_clk, tty_chu and ppsclock streams modules.
|
|
#
|
|
# Spectracom 8170/Netclock-2 WWVB receiver. This receiver is equipped
|
|
# with a 1-pps and IRIG outputs. The 1-pps signal is connected via the
|
|
# ppsclock streams module and the carrier detect line of the CHU
|
|
# receiver below (ttyb). The IRIG signal is connected via an attenuator
|
|
# to the audio port (/dev/audio). The propagation delay computed from
|
|
# geographical coordinates is 8.8 ms, while the receiver delay
|
|
# calibrated at the factory is 17.3 ms, for a total delay of 26.1 ms.
|
|
# This is confirmed within 0.1 ms at the 1-pps signal output using a
|
|
# portable cesium clock. We add a fudge time1 of 3.5 ms so the driver
|
|
# time agrees with the 1-pps signal to within 1 ms. The fudge flag4 is
|
|
# set to cause the receiver to dump the quality table once each day to
|
|
# the clockstats file.
|
|
|
|
#
|
|
#server 127.127.4.1 # /dev/wwvb1 -> /dev/ttyz03
|
|
#fudge 127.127.4.1 time1 0.0035 flag4 1
|
|
#
|
|
# IRIG Audio Decoder. The IRGI signal of the Spectracom WWVB receiver is
|
|
# connected to the audio codec via a resistor attenuator. We add a fudge
|
|
# time1 of 3.5 ms so the driver agrees with the calibrated 1-pps signal
|
|
# to within 0.1 ms. We also specify a reference ID of WWVB to indicate
|
|
# the signal origin. Note the prefer keyword in the server line, which
|
|
# favors this driver over all others that survive the clock selection
|
|
# algorithm. See README.refclock for further insight on this feature.
|
|
#
|
|
server 127.127.6.0 prefer # /dev/audio
|
|
fudge 127.127.6.0 time1 0.0005 refid WWVB
|
|
|
|
#
|
|
# PST/Traconex 1020 WWV/WWVH Receier. The internal DIPswitches are set
|
|
# as near as possible to the delays to WWV (8.8 ms) and WWVH (28.1 ms),
|
|
# as computed from geographical coordinates. We add a fudge time1 of 5.9
|
|
# ms so the driver time agrees with the 1-pps signal to within 1 ms for
|
|
# WWV. We also set the stratum to 1, so this receiver will not normally
|
|
# be selected, unless the primary WWVB receiver comes unstuck.
|
|
#
|
|
server 127.127.3.1 # /dev/pst1 -> ttyz05
|
|
fudge 127.127.3.1 time1 0.0059 stratum 1
|
|
|
|
#
|
|
# Scratchbuilt CHU Receiver. The audio signal from a computer controlled
|
|
# CHU receiver is connected to a gadget box, which contains a 103A modem
|
|
# chip and level converter operating at 300 bps. The propagation delay
|
|
# computed from geographical coordinates is 3.0 ms, which is the value
|
|
# of the fudge time1 parameter. We add a fudge time2 of 9.9 ms so that
|
|
# the driver time agrees with the 1-pps signal to within a few ms,
|
|
# ordinarily the best possible with this receiver. The fudge flag3 is
|
|
# set because the 1-pps signal happens to be connected vit the carrier
|
|
# detect line on this port (ttyb). We also set the stratum to 1, so this
|
|
# receiver will not normally be selected, unless the primary WWVB
|
|
# receiver comes unstuck.
|
|
#
|
|
server 127.127.7.1 # /dev/chu1 -> /dev/ttyb
|
|
fudge 127.127.7.1 time1 0.0030 time2 0.0099 flag3 1 stratum 1
|
|
|
|
#
|
|
# NIST Automated Computer Time Service. This driver calls a special
|
|
# telephone number in Boulder, CO, to fetch the time directly from the
|
|
# NIST cesium farm. The details of the complicated calling program are
|
|
# in the README.refclock file. The Practical Peripherals 9600SA modem
|
|
# does not work correctly with the ACTS echo-delay scheme for
|
|
# automatically calculating the propagation delay, so the fudge flag2 is
|
|
# set to disable the feature. Instead, we add a fudge time1 of 65.0 ms
|
|
# so that the driver time agrees with th e1-pps signal to within 1 ms.
|
|
# The phone command specifies three alternate telephone numbers,
|
|
# including AT modem command prefix, which will be tried one after the
|
|
# other at each measurement attempt. In this case, a cron job is used to
|
|
# set fudge flag1, causing a measurement attempt, every six hours.
|
|
#
|
|
server 127.127.18.1 # /dev/acts1 -> /dev/ttyz00
|
|
fudge 127.127.18.1 time1 0.0650 flag2 1
|
|
phone atdt13034944774 atdt13034944785 atdt13034944774
|
|
|
|
#
|
|
# Heath GC-1000 Most Accurate Clock. This is a WWV receiver with a
|
|
# claimed accuracy better than 100 ms under "hi spec" conditions, but
|
|
# such conditions are not frequent. The propagation delay DIPswitchs are
|
|
# set to 9 ms, as close as possible to the 8.8 ms computed from
|
|
# geographical coordinates. We add a fudge time2 of 40.0 ms so that the
|
|
# driver time agrees with the 1-pps signal to within 50 ms, ordinarily
|
|
# the best possible with this receiver. We also set the stratum to 1, so
|
|
# this receiver will not normally be selected, unless the primary WWVB
|
|
# receiver comes unstuck.
|
|
#
|
|
server 127.127.19.1 # /dev/heath1 -> ttyz07
|
|
fudge 127.127.19.1 time1 0.040 stratum 1
|
|
|
|
#
|
|
# Undisciplined Local Clock. This is a fake driver intended for backup
|
|
# and when no outside source of synchronized time is available. The
|
|
# default stratum is usually 3, but in this case we elect to use stratum
|
|
# 0. Since the server line does not have the prefer keyword, this driver
|
|
# is never used for synchronization, unless no other other
|
|
# synchronization source is available. In case the local host is
|
|
# controlled by some external source, such as an external oscillator or
|
|
# another protocol, the prefer keyword would cause the local host to
|
|
# disregard all other synchronization sources, unless the kernel
|
|
# modifications are in use and declare an unsynchronized condition.
|
|
#
|
|
server 127.127.1.0 # local clock
|
|
fudge 127.127.1.0 stratum 0
|
|
|
|
#
|
|
# PPS Clock. This driver is used to capture a 1-pps signal when the PPS
|
|
# kernel modifications are not in use. It can be configured for the
|
|
# tty_clk or ppsclock streams module or no module at all, assuming the
|
|
# RS232 connector is properly wired. Normally, the 1-pps signal is
|
|
# generated by a radio clock, in this cast the Spectracom clock
|
|
# 127.127.4.1 also configured for this host. When used this way, the
|
|
# associated radio clock normally has the prefer keyword in the serve
|
|
# command line. The PPS driver then will be selected only if the prefer
|
|
# peer is operating within nominal error bounds. See the README.refclock
|
|
# file for further details.
|
|
#
|
|
#server 127.127.22.1 # pps clock
|
|
|
|
#
|
|
# Miscellaneous stuff. We enable authentication in order to prevent
|
|
#
|
|
enable auth monitor # enable the good stuff
|
|
driftfile /etc/ntp.drift # path for drift file
|
|
statsdir /grundoon/ntpstats/ # directory for statistics files
|
|
filegen peerstats file peerstats type day enable
|
|
filegen loopstats file loopstats type day enable
|
|
filegen clockstats file clockstats type day enable
|
|
|
|
#
|
|
# Authentication stuff
|
|
#
|
|
keys /usr/local/ntp.keys # path for keys file
|
|
trustedkey 1 2 3 4 5 6 14 15 # define trusted keys
|
|
requestkey 15 # key (7) for accessing server variables
|
|
controlkey 15 # key (6) for accessing server variables
|
|
authdelay 0.000163 # authentication delay (SPARC4c/40 IPC MD5)
|
|
|