83c41143ca
driver would verify that requests for child devices were confined to any existing I/O windows, but the driver relied on the firmware to initialize the windows and would never grow the windows for new requests. Now the driver actively manages the I/O windows. This is implemented by allocating a bus resource for each I/O window from the parent PCI bus and suballocating that resource to child devices. The suballocations are managed by creating an rman for each I/O window. The suballocated resources are mapped by passing the bus_activate_resource() call up to the parent PCI bus. Windows are grown when needed by using bus_adjust_resource() to adjust the resource allocated from the parent PCI bus. If the adjust request succeeds, the window is adjusted and the suballocation request for the child device is retried. When growing a window, the rman_first_free_region() and rman_last_free_region() routines are used to determine if the front or end of the existing I/O window is free. From using that, the smallest ranges that need to be added to either the front or back of the window are computed. The driver will first try to grow the window in whichever direction requires the smallest growth first followed by the other direction if that fails. Subtractive bridges will first attempt to satisfy requests for child resources from I/O windows (including attempts to grow the windows). If that fails, the request is passed up to the parent PCI bus directly however. The PCI-PCI bridge driver will try to use firmware-assigned ranges for child BARs first and only allocate a "fresh" range if that specific range cannot be accommodated in the I/O window. This allows systems where the firmware assigns resources during boot but later wipes the I/O windows (some ACPI BIOSen are known to do this) to "rediscover" the original I/O window ranges. The ACPI Host-PCI bridge driver has been adjusted to correctly honor hw.acpi.host_mem_start and the I/O port equivalent when a PCI-PCI bridge makes a wildcard request for an I/O window range. The new PCI-PCI bridge driver is only enabled if the NEW_PCIB kernel option is enabled. This is a transition aide to allow platforms that do not yet support bus_activate_resource() and bus_adjust_resource() in their Host-PCI bridge drivers (and possibly other drivers as needed) to use the old driver for now. Once all platforms support the new driver, the kernel option and old driver will be removed. PR: kern/143874 kern/149306 Tested by: mav
This is the top level of the FreeBSD source directory. This file was last revised on: $FreeBSD$ For copyright information, please see the file COPYRIGHT in this directory (additional copyright information also exists for some sources in this tree - please see the specific source directories for more information). The Makefile in this directory supports a number of targets for building components (or all) of the FreeBSD source tree, the most commonly used one being ``world'', which rebuilds and installs everything in the FreeBSD system from the source tree except the kernel, the kernel-modules and the contents of /etc. The ``world'' target should only be used in cases where the source tree has not changed from the currently running version. See: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/makeworld.html for more information, including setting make(1) variables. The ``buildkernel'' and ``installkernel'' targets build and install the kernel and the modules (see below). Please see the top of the Makefile in this directory for more information on the standard build targets and compile-time flags. Building a kernel is a somewhat more involved process, documentation for which can be found at: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig.html And in the config(8) man page. Note: If you want to build and install the kernel with the ``buildkernel'' and ``installkernel'' targets, you might need to build world before. More information is available in the handbook. The sample kernel configuration files reside in the sys/<arch>/conf sub-directory (assuming that you've installed the kernel sources), the file named GENERIC being the one used to build your initial installation kernel. The file NOTES contains entries and documentation for all possible devices, not just those commonly used. It is the successor of the ancient LINT file, but in contrast to LINT, it is not buildable as a kernel but a pure reference and documentation file. Source Roadmap: --------------- bin System/user commands. cddl Various commands and libraries under the Common Development and Distribution License. contrib Packages contributed by 3rd parties. crypto Cryptography stuff (see crypto/README). etc Template files for /etc. games Amusements. gnu Various commands and libraries under the GNU Public License. Please see gnu/COPYING* for more information. include System include files. kerberos5 Kerberos5 (Heimdal) package. lib System libraries. libexec System daemons. release Release building Makefile & associated tools. rescue Build system for statically linked /rescue utilities. sbin System commands. secure Cryptographic libraries and commands. share Shared resources. sys Kernel sources. tools Utilities for regression testing and miscellaneous tasks. usr.bin User commands. usr.sbin System administration commands. For information on synchronizing your source tree with one or more of the FreeBSD Project's development branches, please see: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/synching.html