b14a705362
The SoC, the flash, the ethernet ports and ethernet switch all work. The USB works. The 11ac PCIe NIC internally is at least seen by the PCIE RC, but I haven't tried using it yet. There's no driver and I haven't yet swapped it out for a non-11ac chip. The on-chip 2GHz wifi works, but there are some data errors that get thrown up in STA mode when scanning. I have a feeling I have to finish the DDR flush code out and have it run correctly on the shared interrupts; that'll take a bit of time to get right. But if you're after an updated piece of hardware, the Archer C7 v2 is certainly there, and you can replace the 11ac NIC with a 3x3 Atheros PCIe device (eg AR9380, AR9390, AR9580, etc) and it'll "just work". Tested: * TP-Link archer c7v2.
69 lines
1.7 KiB
Plaintext
69 lines
1.7 KiB
Plaintext
#
|
|
# TP-Link Archer C7 - based on the AP135 reference design.
|
|
#
|
|
# This contains a QCA9558 MIPS74k SoC with on-board 3x3 2GHz wifi,
|
|
# 128MiB RAM, an AR8327 5-port gigabit ethernet switch and
|
|
# a QCA 11ac 5GHz AP NIC.
|
|
#
|
|
# The to things not currently support are the QCA 11ac NIC and
|
|
# PCIe host controllers - there's two of them, and the existing
|
|
# PCIe code here doesn't support that just yet.
|
|
#
|
|
# $FreeBSD$
|
|
#
|
|
|
|
# Include the default QCA955x parameters
|
|
include "QCA955X_BASE"
|
|
|
|
ident TL-ARCHERC7V2
|
|
|
|
# Override hints with board values
|
|
hints "TL-ARCHERC7V2.hints"
|
|
|
|
# Force the board memory - this has 128MiB RAM
|
|
options AR71XX_REALMEM=(128*1024*1024)
|
|
|
|
# i2c GPIO bus
|
|
#device gpioiic
|
|
#device iicbb
|
|
#device iicbus
|
|
#device iic
|
|
|
|
# Options required for miiproxy and mdiobus
|
|
options ARGE_MDIO # Export an MDIO bus separate from arge
|
|
device miiproxy # MDIO bus <-> MII PHY rendezvous
|
|
|
|
device etherswitch
|
|
device arswitch
|
|
|
|
# read MSDOS formatted disks - USB
|
|
options MSDOSFS
|
|
|
|
# Enable the uboot environment stuff rather then the
|
|
# redboot stuff.
|
|
options AR71XX_ENV_UBOOT
|
|
|
|
# uzip - to boot natively from flash
|
|
device geom_uncompress
|
|
options GEOM_UNCOMPRESS
|
|
|
|
# Used for the static uboot partition map
|
|
device geom_map
|
|
|
|
# yes, this board has a PCIe connected atheros device
|
|
# add ath_pci so it can at least attach things when there's a
|
|
# ath(4) in there, rather than the 11ac chip we don't support.
|
|
device pci
|
|
device qca955x_pci
|
|
|
|
device ath_pci
|
|
options AR71XX_ATH_EEPROM
|
|
device firmware # Used by the above
|
|
options ATH_EEPROM_FIRMWARE
|
|
|
|
# Boot off of the rootfs, as defined in the geom_map setup.
|
|
options ROOTDEVNAME=\"ufs:map/rootfs.uncompress\"
|
|
|
|
# Default to accept
|
|
options IPFIREWALL_DEFAULT_TO_ACCEPT
|