208 lines
7.0 KiB
Groff
208 lines
7.0 KiB
Groff
.\" Copyright (c) 2009-2013 Alexander Motin <mav@FreeBSD.org>
|
|
.\" All rights reserved.
|
|
.\"
|
|
.\" Redistribution and use in source and binary forms, with or without
|
|
.\" modification, are permitted provided that the following conditions
|
|
.\" are met:
|
|
.\" 1. Redistributions of source code must retain the above copyright
|
|
.\" notice, this list of conditions and the following disclaimer.
|
|
.\" 2. Redistributions in binary form must reproduce the above copyright
|
|
.\" notice, this list of conditions and the following disclaimer in the
|
|
.\" documentation and/or other materials provided with the distribution.
|
|
.\"
|
|
.\" THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
|
|
.\" ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
.\" IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
.\" ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
|
|
.\" FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
.\" DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
.\" OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
.\" HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
.\" LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
.\" OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
.\" SUCH DAMAGE.
|
|
.\"
|
|
.\" $FreeBSD$
|
|
.\"
|
|
.Dd August 21, 2019
|
|
.Dt AHCI 4
|
|
.Os
|
|
.Sh NAME
|
|
.Nm ahci
|
|
.Nd Serial ATA Advanced Host Controller Interface driver
|
|
.Sh SYNOPSIS
|
|
To compile this driver into the kernel,
|
|
place the following lines in your
|
|
kernel configuration file:
|
|
.Bd -ragged -offset indent
|
|
.Cd "device pci"
|
|
.Cd "device scbus"
|
|
.Cd "device ahci"
|
|
.Ed
|
|
.Pp
|
|
Alternatively, to load the driver as a
|
|
module at boot time, place the following line in
|
|
.Xr loader.conf 5 :
|
|
.Bd -literal -offset indent
|
|
ahci_load="YES"
|
|
.Ed
|
|
.Pp
|
|
The following tunables are settable from the
|
|
.Xr loader 8 :
|
|
.Bl -ohang
|
|
.It Va hint.ahci. Ns Ar X Ns Va .msi
|
|
controls Message Signaled Interrupts (MSI) usage by the specified controller.
|
|
.Pp
|
|
.Bl -tag -width 4n -offset indent -compact
|
|
.It 0
|
|
MSI disabled;
|
|
.It 1
|
|
single MSI vector used, if supported;
|
|
.It 2
|
|
multiple MSI vectors used, if supported (default);
|
|
.El
|
|
.It Va hint.ahci. Ns Ar X Ns Va .ccc
|
|
controls Command Completion Coalescing (CCC) usage by the specified controller.
|
|
Non-zero value enables CCC and defines maximum time (in ms), request can wait
|
|
for interrupt, if there are some more requests present on controller queue.
|
|
CCC reduces number of context switches on systems with many parallel requests,
|
|
but it can decrease disk performance on some workloads due to additional
|
|
command latency.
|
|
.It Va hint.ahci. Ns Ar X Ns Va .direct
|
|
controls whether the driver should use direct command completion from
|
|
interrupt thread(s), or queue them to CAM completion threads.
|
|
Default value depends on number of MSI interrupts supported and number of
|
|
implemented SATA ports.
|
|
.It Va hint.ahcich. Ns Ar X Ns Va .pm_level
|
|
controls SATA interface Power Management for the specified channel,
|
|
allowing some power to be saved at the cost of additional command
|
|
latency.
|
|
Possible values:
|
|
.Pp
|
|
.Bl -tag -width 4n -offset indent -compact
|
|
.It 0
|
|
interface Power Management is disabled (default);
|
|
.It 1
|
|
device is allowed to initiate PM state change, host is passive;
|
|
.It 2
|
|
host initiates PARTIAL PM state transition every time port becomes idle;
|
|
.It 3
|
|
host initiates SLUMBER PM state transition every time port becomes idle.
|
|
.It 4
|
|
driver initiates PARTIAL PM state transition 1ms after port becomes idle;
|
|
.It 5
|
|
driver initiates SLUMBER PM state transition 125ms after port becomes idle.
|
|
.El
|
|
.Pp
|
|
Some controllers, such as ICH8, do not implement modes 2 and 3 with NCQ used.
|
|
Because of artificial entering latency, performance degradation in modes
|
|
4 and 5 is much smaller then in modes 2 and 3.
|
|
.Pp
|
|
Note that interface Power Management complicates device presence detection.
|
|
A manual bus reset/rescan may be needed after device hot-plug, unless hardware
|
|
implements Cold Presence Detection.
|
|
.It Va hint.ahcich. Ns Ar X Ns Va .sata_rev
|
|
setting to nonzero value limits maximum SATA revision (speed).
|
|
Values 1, 2 and 3 are respectively 1.5, 3 and 6Gbps.
|
|
.It Va hw.ahci.force
|
|
setting to nonzero value forces driver attach to some known AHCI-capable
|
|
chips even if they are configured for legacy IDE emulation.
|
|
Default is 1.
|
|
.El
|
|
.Sh DESCRIPTION
|
|
This driver provides the
|
|
.Xr CAM 4
|
|
subsystem with native access to the
|
|
.Tn SATA
|
|
ports of AHCI-compatible controllers.
|
|
Each SATA port found is represented to CAM as a separate bus with one
|
|
target, or, if HBA supports Port Multipliers, 16 targets.
|
|
Most of the bus-management details are handled by the SATA-specific
|
|
transport of CAM.
|
|
Connected ATA disks are handled by the ATA protocol disk peripheral driver
|
|
.Xr ada 4 .
|
|
ATAPI devices are handled by the SCSI protocol peripheral drivers
|
|
.Xr cd 4 ,
|
|
.Xr da 4 ,
|
|
.Xr sa 4 ,
|
|
etc.
|
|
.Pp
|
|
Driver features include support for Serial ATA and ATAPI devices,
|
|
Port Multipliers (including FIS-based switching, when supported),
|
|
hardware command queues (up to 32 commands per port),
|
|
Native Command Queuing, SATA interface Power Management, device hot-plug
|
|
and Message Signaled Interrupts.
|
|
.Pp
|
|
Driver supports "LED" enclosure management messages, defined by the AHCI.
|
|
When supported by hardware, it allows to control per-port activity, locate
|
|
and fault LEDs via the
|
|
.Xr led 4
|
|
API or emulated
|
|
.Xr ses 4
|
|
device for localization and status reporting purposes.
|
|
Supporting AHCI controllers may transmit that information to the backplane
|
|
controllers via SGPIO interface.
|
|
Backplane controllers interpret received
|
|
statuses in some way (IBPI standard) to report them using present indicators.
|
|
.Sh HARDWARE
|
|
The
|
|
.Nm
|
|
driver supports AHCI compatible controllers having PCI class 1 (mass storage),
|
|
subclass 6 (SATA) and programming interface 1 (AHCI).
|
|
.Pp
|
|
Also, in cooperation with atamarvell and atajmicron drivers of ata(4),
|
|
it supports AHCI part of legacy-PATA + AHCI-SATA combined controllers,
|
|
such as JMicron JMB36x and Marvell 88SE61xx.
|
|
.Pp
|
|
The
|
|
.Nm
|
|
driver also supports AHCI devices that act as PCI bridges for
|
|
.Xr nvme 4
|
|
using Intel Rapid Storage Technology (RST).
|
|
To use the
|
|
.Xr nvme 4
|
|
device, either one must set the SATA mode in the BIOS to AHCI (from RST),
|
|
or one must accept the performance with RST enabled due to interrupt sharing.
|
|
.Fx
|
|
will automatically detect AHCI devices with this extension that are in RST
|
|
mode.
|
|
When that happens,
|
|
.Nm
|
|
will attach
|
|
.Xr nvme 4
|
|
children to the
|
|
.Xr ahci 4
|
|
device.
|
|
.Sh FILES
|
|
.Bl -tag -width /dev/led/ahcich*.locate
|
|
.It Pa /dev/led/ahci*.*.act
|
|
activity LED device nodes
|
|
.It Pa /dev/led/ahci*.*.fault
|
|
fault LED device nodes
|
|
.It Pa /dev/led/ahci*.*.locate
|
|
locate LED device nodes
|
|
.El
|
|
.Sh SYSCTL
|
|
.Bl -tag
|
|
.It Pa dev.ahcich.X.disable_phy
|
|
Set to 1 to disable the phy for the drive on channel X.
|
|
Set to 0 to enable the phy.
|
|
Useful for turning off troublemakers.
|
|
Also useful for debugging when you need the ada drive to come and go.
|
|
.El
|
|
.Sh SEE ALSO
|
|
.Xr ada 4 ,
|
|
.Xr ata 4 ,
|
|
.Xr cam 4 ,
|
|
.Xr cd 4 ,
|
|
.Xr da 4 ,
|
|
.Xr sa 4 ,
|
|
.Xr ses 4
|
|
.Sh HISTORY
|
|
The
|
|
.Nm
|
|
driver first appeared in
|
|
.Fx 8.0 .
|
|
.Sh AUTHORS
|
|
.An Alexander Motin Aq Mt mav@FreeBSD.org
|