b7da7b3e2a
check out the README that is included. Submitted by: Luigi Rizzo <luigi@labinfo.iet.unipi.it>
251 lines
8.9 KiB
C
251 lines
8.9 KiB
C
/*
|
|
* file: mss.h
|
|
*
|
|
* (C) 1997 Luigi Rizzo (luigi@iet.unipi.it)
|
|
*
|
|
* This file contains information and macro definitions for
|
|
* AD1848-compatible devices, used in the MSS/WSS compatible boards.
|
|
*
|
|
*/
|
|
|
|
/*
|
|
*
|
|
|
|
The codec part of the board is seen as a set of 4 registers mapped
|
|
at the base address for the board (default 0x534). Note that some
|
|
(early) boards implemented 4 additional registers 4 location before
|
|
(usually 0x530) to store configuration information. This is a source
|
|
of confusion in that one never knows what address to specify. The
|
|
(current) convention is to use the old address (0x530) in the kernel
|
|
configuration file and consider MSS registers start four location
|
|
ahead.
|
|
|
|
*
|
|
*/
|
|
|
|
/*
|
|
* The four visible registers of the MSS :
|
|
*
|
|
*/
|
|
|
|
#define io_Index_Addr(d) ((d)->io_base + 4)
|
|
#define IA_BUSY 0x80 /* readonly, set when busy */
|
|
#define IA_MCE 0x40 /* the MCE bit. */
|
|
/*
|
|
* the MCE bit must be set whenever the current mode of the
|
|
* codec is changed; this in particular is true for the
|
|
* Data Format (I8, I28) and Interface Config(I9) registers.
|
|
* Only exception are CEN and PEN which can be changed on the fly.
|
|
* The DAC output is muted when MCE is set.
|
|
*/
|
|
#define IA_TRD 0x20 /* Transfer request disable */
|
|
/*
|
|
* When TRD is set, DMA transfers cease when the INT bit in
|
|
* the MSS status reg is set. Must be cleared for automode
|
|
* DMA, set otherwise.
|
|
*/
|
|
#define IA_AMASK 0x1f /* mask for indirect address */
|
|
|
|
#define io_Indexed_Data(d) ((d)->io_base+1+4)
|
|
/*
|
|
* data to be transferred to the indirect register addressed
|
|
* by index addr. During init and sw. powerdown, cannot be
|
|
* written to, and is always read as 0x80 (consistent with the
|
|
* busy flag).
|
|
*/
|
|
|
|
#define io_Status(d) ((d)->io_base+2+4)
|
|
|
|
#define IS_CUL 0x80 /* capture upper/lower */
|
|
#define IS_CLR 0x40 /* capture left/right */
|
|
#define IS_CRDY 0x20 /* capture ready for programmed i/o */
|
|
#define IS_SER 0x10 /* sample error (overrun/underrun) */
|
|
#define IS_PUL 0x08 /* playback upper/lower */
|
|
#define IS_PLR 0x04 /* playback left/right */
|
|
#define IS_PRDY 0x02 /* playback ready for programmed i/o */
|
|
#define IS_INT 0x01 /* int status (1 = active) */
|
|
/*
|
|
* IS_INT is clreared by any write to the status register.
|
|
*/
|
|
|
|
#define io_Polled_IO(d) ((d)->io_base+3+4)
|
|
/*
|
|
* this register is used in case of polled i/o
|
|
*/
|
|
|
|
/*
|
|
* The MSS has a set of 16 (or 32 depending on the model) indirect
|
|
* registers accessible through the data port by specifying the
|
|
* appropriate address in the address register.
|
|
*
|
|
* The 16 low registers are uniformly handled in AD1848/CS4248 compatible
|
|
* mode (often called MODE1). For the upper 16 registers there are
|
|
* some differences among different products, mainly Crystal uses them
|
|
* differently from OPTi.
|
|
*
|
|
*/
|
|
|
|
/*
|
|
* volume registers
|
|
*/
|
|
|
|
#define I6_MUTE 0x80
|
|
|
|
/*
|
|
* register I9 -- interface configuration.
|
|
*/
|
|
|
|
#define I9_PEN 0x01 /* playback enable */
|
|
#define I9_CEN 0x02 /* capture enable */
|
|
|
|
/*
|
|
* values used in bd_flags
|
|
*/
|
|
#define BD_F_MCE_BIT 0x0001
|
|
#define BD_F_IRQ_OK 0x0002
|
|
#define BD_F_TMR_RUN 0x0004
|
|
|
|
|
|
/*
|
|
* sound/ad1848_mixer.h
|
|
*
|
|
* Definitions for the mixer of AD1848 and compatible codecs.
|
|
*
|
|
* Copyright by Hannu Savolainen 1994
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions are
|
|
* met: 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer. 2.
|
|
* Redistributions in binary form must reproduce the above copyright notice,
|
|
* this list of conditions and the following disclaimer in the documentation
|
|
* and/or other materials provided with the distribution.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND ANY
|
|
* EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
|
|
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
|
|
* DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
|
|
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
|
|
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
|
|
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGE.
|
|
*/
|
|
/*
|
|
* The AD1848 codec has generic input lines called Line, Aux1 and Aux2.
|
|
* Soundcard manufacturers have connected actual inputs (CD, synth, line,
|
|
* etc) to these inputs in different order. Therefore it's difficult
|
|
* to assign mixer channels to to these inputs correctly. The following
|
|
* contains two alternative mappings. The first one is for GUS MAX and
|
|
* the second is just a generic one (line1, line2 and line3).
|
|
* (Actually this is not a mapping but rather some kind of interleaving
|
|
* solution).
|
|
*/
|
|
#define GUSMAX_MIXER
|
|
#ifdef GUSMAX_MIXER
|
|
#define MODE1_REC_DEVICES \
|
|
(SOUND_MASK_LINE | SOUND_MASK_MIC | SOUND_MASK_CD|SOUND_MASK_IMIX)
|
|
|
|
#define MODE1_MIXER_DEVICES \
|
|
(SOUND_MASK_SYNTH | SOUND_MASK_MIC | SOUND_MASK_CD | \
|
|
SOUND_MASK_IGAIN | SOUND_MASK_PCM|SOUND_MASK_IMIX)
|
|
|
|
#define MODE2_MIXER_DEVICES \
|
|
(SOUND_MASK_SYNTH | SOUND_MASK_LINE | SOUND_MASK_MIC | \
|
|
SOUND_MASK_CD | SOUND_MASK_SPEAKER | SOUND_MASK_IGAIN | \
|
|
SOUND_MASK_PCM | SOUND_MASK_IMIX)
|
|
|
|
#else /* Generic mapping */
|
|
|
|
#define MODE1_REC_DEVICES \
|
|
(SOUND_MASK_LINE3 | SOUND_MASK_MIC | SOUND_MASK_LINE1|SOUND_MASK_IMIX)
|
|
|
|
#define MODE1_MIXER_DEVICES \
|
|
(SOUND_MASK_LINE1 | SOUND_MASK_MIC | SOUND_MASK_LINE2 | \
|
|
SOUND_MASK_IGAIN | SOUND_MASK_PCM | SOUND_MASK_IMIX)
|
|
|
|
#define MODE2_MIXER_DEVICES \
|
|
(SOUND_MASK_LINE1 | SOUND_MASK_MIC | SOUND_MASK_LINE2 | \
|
|
SOUND_MASK_LINE3 | SOUND_MASK_SPEAKER | \
|
|
SOUND_MASK_IGAIN | SOUND_MASK_PCM | SOUND_MASK_IMIX)
|
|
#endif
|
|
|
|
#define OPTI931_MIXER_DEVICES \
|
|
(SOUND_MASK_VOLUME | SOUND_MASK_SYNTH | SOUND_MASK_PCM | \
|
|
SOUND_MASK_LINE | SOUND_MASK_MIC | SOUND_MASK_CD | SOUND_MASK_IGAIN )
|
|
|
|
/*
|
|
* Most of the mixer entries work in backwards. Setting the polarity field
|
|
* makes them to work correctly.
|
|
*
|
|
* The channel numbering used by individual soundcards is not fixed.
|
|
* Some cards have assigned different meanings for the AUX1, AUX2
|
|
* and LINE inputs. Some have different features...
|
|
* The current version doesn't try to compensate this.
|
|
*
|
|
*/
|
|
|
|
mixer_ent mix_devices[32][2] = { /* As used in GUS MAX */
|
|
MIX_ENT(SOUND_MIXER_VOLUME, 0, 0, 0, 0, 0, 0, 0, 0),
|
|
MIX_ENT(SOUND_MIXER_BASS, 0, 0, 0, 0, 0, 0, 0, 0),
|
|
MIX_ENT(SOUND_MIXER_TREBLE, 0, 0, 0, 0, 0, 0, 0, 0),
|
|
MIX_ENT(SOUND_MIXER_SYNTH, 4, 1, 0, 5, 5, 1, 0, 5),
|
|
MIX_ENT(SOUND_MIXER_PCM, 6, 1, 0, 6, 7, 1, 0, 6),
|
|
MIX_ENT(SOUND_MIXER_SPEAKER, 26, 1, 0, 4, 0, 0, 0, 0),
|
|
MIX_ENT(SOUND_MIXER_LINE, 18, 1, 0, 5, 19, 1, 0, 5),
|
|
MIX_ENT(SOUND_MIXER_MIC, 0, 0, 5, 1, 1, 0, 5, 1),
|
|
MIX_ENT(SOUND_MIXER_CD, 2, 1, 0, 5, 3, 1, 0, 5),
|
|
MIX_ENT(SOUND_MIXER_IMIX, 13, 1, 2, 6, 0, 0, 0, 0),
|
|
MIX_ENT(SOUND_MIXER_ALTPCM, 0, 0, 0, 0, 0, 0, 0, 0),
|
|
MIX_ENT(SOUND_MIXER_RECLEV, 0, 0, 0, 0, 0, 0, 0, 0),
|
|
MIX_ENT(SOUND_MIXER_IGAIN, 0, 0, 0, 4, 1, 0, 0, 4),
|
|
MIX_ENT(SOUND_MIXER_OGAIN, 0, 0, 0, 0, 0, 0, 0, 0),
|
|
MIX_ENT(SOUND_MIXER_LINE1, 2, 1, 0, 5, 3, 1, 0, 5),
|
|
MIX_ENT(SOUND_MIXER_LINE2, 4, 1, 0, 5, 5, 1, 0, 5),
|
|
MIX_ENT(SOUND_MIXER_LINE3, 18, 1, 0, 5, 19, 1, 0, 5)
|
|
};
|
|
|
|
mixer_ent opti931_devices[32][2] = { /* for the opti931 */
|
|
MIX_ENT(SOUND_MIXER_VOLUME, 22, 1, 1, 5, 23, 1, 1, 5),
|
|
MIX_ENT(SOUND_MIXER_BASS, 0, 0, 0, 0, 0, 0, 0, 0),
|
|
MIX_ENT(SOUND_MIXER_TREBLE, 0, 0, 0, 0, 0, 0, 0, 0),
|
|
MIX_ENT(SOUND_MIXER_SYNTH, 4, 1, 1, 4, 5, 1, 1, 4),
|
|
MIX_ENT(SOUND_MIXER_PCM, 6, 1, 0, 5, 7, 1, 0, 5),
|
|
MIX_ENT(SOUND_MIXER_SPEAKER, 0, 0, 0, 0, 0, 0, 0, 0),
|
|
MIX_ENT(SOUND_MIXER_LINE, 18, 1, 1, 4, 19, 1, 1, 4),
|
|
MIX_ENT(SOUND_MIXER_MIC, 0, 0, 5, 1, 1, 0, 5, 1),
|
|
MIX_ENT(SOUND_MIXER_CD, 2, 1, 1, 4, 3, 1, 1, 4),
|
|
MIX_ENT(SOUND_MIXER_IMIX, 0, 0, 0, 0, 0, 0, 0, 0),
|
|
MIX_ENT(SOUND_MIXER_ALTPCM, 0, 0, 0, 0, 0, 0, 0, 0),
|
|
MIX_ENT(SOUND_MIXER_RECLEV, 0, 0, 0, 0, 0, 0, 0, 0),
|
|
MIX_ENT(SOUND_MIXER_IGAIN, 0, 0, 0, 4, 1, 0, 0, 4),
|
|
MIX_ENT(SOUND_MIXER_OGAIN, 0, 0, 0, 0, 0, 0, 0, 0),
|
|
MIX_ENT(SOUND_MIXER_LINE1, 2, 1, 0, 5, 3, 1, 0, 5),
|
|
MIX_ENT(SOUND_MIXER_LINE2, 4, 1, 0, 5, 5, 1, 0, 5),
|
|
MIX_ENT(SOUND_MIXER_LINE3, 18, 1, 0, 5, 19, 1, 0, 5)
|
|
};
|
|
|
|
static u_short default_mixer_levels[SOUND_MIXER_NRDEVICES] = {
|
|
0x5a5a, /* Master Volume */
|
|
0x3232, /* Bass */
|
|
0x3232, /* Treble */
|
|
0x4b4b, /* FM */
|
|
0x4040, /* PCM */
|
|
0x4b4b, /* PC Speaker */
|
|
0x2020, /* Ext Line */
|
|
0x4040, /* Mic */
|
|
0x4b4b, /* CD */
|
|
0x0000, /* Recording monitor */
|
|
0x4b4b, /* SB PCM */
|
|
0x4b4b, /* Recording level */
|
|
0x2525, /* Input gain */
|
|
0x0000, /* Output gain */
|
|
/* 0x4040, Line1 */
|
|
0x0000, /* Line1 */
|
|
0x0000, /* Line2 */
|
|
0x1515 /* Line3 (usually line in)*/
|
|
};
|
|
|