freebsd-skq/sys/arm/allwinner/a10_hdmi.c
manu a839bad498 Enable the SCL and SDA i2c line for DDC.
This is an undocumented register that we need to set if we do not want to
rely on u-boot or other bootloader.
2016-11-24 01:24:26 +00:00

726 lines
19 KiB
C

/*-
* Copyright (c) 2016 Jared McNeill <jmcneill@invisible.ca>
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* $FreeBSD$
*/
/*
* Allwinner A10/A20 HDMI TX
*/
#include <sys/cdefs.h>
__FBSDID("$FreeBSD$");
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/bus.h>
#include <sys/rman.h>
#include <sys/condvar.h>
#include <sys/kernel.h>
#include <sys/module.h>
#include <machine/bus.h>
#include <dev/ofw/ofw_bus.h>
#include <dev/ofw/ofw_bus_subr.h>
#include <dev/videomode/videomode.h>
#include <dev/videomode/edidvar.h>
#include <dev/extres/clk/clk.h>
#include "hdmi_if.h"
#define HDMI_CTRL 0x004
#define CTRL_MODULE_EN (1 << 31)
#define HDMI_INT_STATUS 0x008
#define HDMI_HPD 0x00c
#define HPD_DET (1 << 0)
#define HDMI_VID_CTRL 0x010
#define VID_CTRL_VIDEO_EN (1 << 31)
#define VID_CTRL_HDMI_MODE (1 << 30)
#define VID_CTRL_INTERLACE (1 << 4)
#define VID_CTRL_REPEATER_2X (1 << 0)
#define HDMI_VID_TIMING0 0x014
#define VID_ACT_V(v) (((v) - 1) << 16)
#define VID_ACT_H(h) (((h) - 1) << 0)
#define HDMI_VID_TIMING1 0x018
#define VID_VBP(vbp) (((vbp) - 1) << 16)
#define VID_HBP(hbp) (((hbp) - 1) << 0)
#define HDMI_VID_TIMING2 0x01c
#define VID_VFP(vfp) (((vfp) - 1) << 16)
#define VID_HFP(hfp) (((hfp) - 1) << 0)
#define HDMI_VID_TIMING3 0x020
#define VID_VSPW(vspw) (((vspw) - 1) << 16)
#define VID_HSPW(hspw) (((hspw) - 1) << 0)
#define HDMI_VID_TIMING4 0x024
#define TX_CLOCK_NORMAL 0x03e00000
#define VID_VSYNC_ACTSEL (1 << 1)
#define VID_HSYNC_ACTSEL (1 << 0)
#define HDMI_AUD_CTRL 0x040
#define AUD_CTRL_EN (1 << 31)
#define AUD_CTRL_RST (1 << 30)
#define HDMI_ADMA_CTRL 0x044
#define HDMI_ADMA_MODE (1 << 31)
#define HDMI_ADMA_MODE_DDMA (0 << 31)
#define HDMI_ADMA_MODE_NDMA (1 << 31)
#define HDMI_AUD_FMT 0x048
#define AUD_FMT_CH(n) ((n) - 1)
#define HDMI_PCM_CTRL 0x04c
#define HDMI_AUD_CTS 0x050
#define HDMI_AUD_N 0x054
#define HDMI_AUD_CH_STATUS0 0x058
#define CH_STATUS0_FS_FREQ (0xf << 24)
#define CH_STATUS0_FS_FREQ_48 (2 << 24)
#define HDMI_AUD_CH_STATUS1 0x05c
#define CH_STATUS1_WORD_LEN (0x7 << 1)
#define CH_STATUS1_WORD_LEN_16 (1 << 1)
#define HDMI_AUDIO_RESET_RETRY 1000
#define HDMI_AUDIO_CHANNELS 2
#define HDMI_AUDIO_CHANNELMAP 0x76543210
#define HDMI_AUDIO_N 6144 /* 48 kHz */
#define HDMI_AUDIO_CTS(r, n) ((((r) * 10) * ((n) / 128)) / 480)
#define HDMI_PADCTRL0 0x200
#define PADCTRL0_BIASEN (1 << 31)
#define PADCTRL0_LDOCEN (1 << 30)
#define PADCTRL0_LDODEN (1 << 29)
#define PADCTRL0_PWENC (1 << 28)
#define PADCTRL0_PWEND (1 << 27)
#define PADCTRL0_PWENG (1 << 26)
#define PADCTRL0_CKEN (1 << 25)
#define PADCTRL0_SEN (1 << 24)
#define PADCTRL0_TXEN (1 << 23)
#define HDMI_PADCTRL1 0x204
#define PADCTRL1_AMP_OPT (1 << 23)
#define PADCTRL1_AMPCK_OPT (1 << 22)
#define PADCTRL1_DMP_OPT (1 << 21)
#define PADCTRL1_EMP_OPT (1 << 20)
#define PADCTRL1_EMPCK_OPT (1 << 19)
#define PADCTRL1_PWSCK (1 << 18)
#define PADCTRL1_PWSDT (1 << 17)
#define PADCTRL1_REG_CSMPS (1 << 16)
#define PADCTRL1_REG_DEN (1 << 15)
#define PADCTRL1_REG_DENCK (1 << 14)
#define PADCTRL1_REG_PLRCK (1 << 13)
#define PADCTRL1_REG_EMP (0x7 << 10)
#define PADCTRL1_REG_EMP_EN (0x2 << 10)
#define PADCTRL1_REG_CD (0x3 << 8)
#define PADCTRL1_REG_CKSS (0x3 << 6)
#define PADCTRL1_REG_CKSS_1X (0x1 << 6)
#define PADCTRL1_REG_CKSS_2X (0x0 << 6)
#define PADCTRL1_REG_AMP (0x7 << 3)
#define PADCTRL1_REG_AMP_EN (0x6 << 3)
#define PADCTRL1_REG_PLR (0x7 << 0)
#define HDMI_PLLCTRL0 0x208
#define PLLCTRL0_PLL_EN (1 << 31)
#define PLLCTRL0_BWS (1 << 30)
#define PLLCTRL0_HV_IS_33 (1 << 29)
#define PLLCTRL0_LDO1_EN (1 << 28)
#define PLLCTRL0_LDO2_EN (1 << 27)
#define PLLCTRL0_SDIV2 (1 << 25)
#define PLLCTRL0_VCO_GAIN (0x1 << 22)
#define PLLCTRL0_S (0x7 << 17)
#define PLLCTRL0_CP_S (0xf << 12)
#define PLLCTRL0_CS (0x7 << 8)
#define PLLCTRL0_PREDIV(x) ((x) << 4)
#define PLLCTRL0_VCO_S (0x8 << 0)
#define HDMI_PLLDBG0 0x20c
#define PLLDBG0_CKIN_SEL (1 << 21)
#define PLLDBG0_CKIN_SEL_PLL3 (0 << 21)
#define PLLDBG0_CKIN_SEL_PLL7 (1 << 21)
#define HDMI_PKTCTRL0 0x2f0
#define HDMI_PKTCTRL1 0x2f4
#define PKTCTRL_PACKET(n,t) ((t) << ((n) << 2))
#define PKT_NULL 0
#define PKT_GC 1
#define PKT_AVI 2
#define PKT_AI 3
#define PKT_SPD 5
#define PKT_END 15
#define DDC_CTRL 0x500
#define CTRL_DDC_EN (1 << 31)
#define CTRL_DDC_ACMD_START (1 << 30)
#define CTRL_DDC_FIFO_DIR (1 << 8)
#define CTRL_DDC_FIFO_DIR_READ (0 << 8)
#define CTRL_DDC_FIFO_DIR_WRITE (1 << 8)
#define CTRL_DDC_SWRST (1 << 0)
#define DDC_SLAVE_ADDR 0x504
#define SLAVE_ADDR_SEG_SHIFT 24
#define SLAVE_ADDR_EDDC_SHIFT 16
#define SLAVE_ADDR_OFFSET_SHIFT 8
#define SLAVE_ADDR_SHIFT 0
#define DDC_INT_STATUS 0x50c
#define INT_STATUS_XFER_DONE (1 << 0)
#define DDC_FIFO_CTRL 0x510
#define FIFO_CTRL_CLEAR (1 << 31)
#define DDC_BYTE_COUNTER 0x51c
#define DDC_COMMAND 0x520
#define COMMAND_EOREAD (4 << 0)
#define DDC_CLOCK 0x528
#define DDC_CLOCK_M (1 << 3)
#define DDC_CLOCK_N (5 << 0)
#define DDC_FIFO 0x518
#define SWRST_DELAY 1000
#define DDC_DELAY 1000
#define DDC_RETRY 1000
#define DDC_BLKLEN 16
#define DDC_ADDR 0x50
#define EDDC_ADDR 0x60
#define EDID_LENGTH 128
#define DDC_CTRL_LINE 0x540
#define DDC_LINE_SCL_ENABLE (1 << 8)
#define DDC_LINE_SDA_ENABLE (1 << 9)
#define HDMI_ENABLE_DELAY 50000
#define DDC_READ_RETRY 4
#define EXT_TAG 0x00
#define CEA_TAG_ID 0x02
#define CEA_DTD 0x03
#define DTD_BASIC_AUDIO (1 << 6)
#define CEA_REV 0x02
#define CEA_DATA_OFF 0x03
#define CEA_DATA_START 4
#define BLOCK_TAG(x) (((x) >> 5) & 0x7)
#define BLOCK_TAG_VSDB 3
#define BLOCK_LEN(x) ((x) & 0x1f)
#define HDMI_VSDB_MINLEN 5
#define HDMI_OUI "\x03\x0c\x00"
#define HDMI_OUI_LEN 3
#define HDMI_DEFAULT_FREQ 297000000
struct a10hdmi_softc {
struct resource *res;
struct intr_config_hook mode_hook;
uint8_t edid[EDID_LENGTH];
int has_hdmi;
int has_audio;
clk_t clk_ahb;
clk_t clk_hdmi;
clk_t clk_lcd;
};
static struct resource_spec a10hdmi_spec[] = {
{ SYS_RES_MEMORY, 0, RF_ACTIVE },
{ -1, 0 }
};
#define HDMI_READ(sc, reg) bus_read_4((sc)->res, (reg))
#define HDMI_WRITE(sc, reg, val) bus_write_4((sc)->res, (reg), (val))
static void
a10hdmi_init(struct a10hdmi_softc *sc)
{
/* Enable the HDMI module */
HDMI_WRITE(sc, HDMI_CTRL, CTRL_MODULE_EN);
/* Configure PLL/DRV settings */
HDMI_WRITE(sc, HDMI_PADCTRL0, PADCTRL0_BIASEN | PADCTRL0_LDOCEN |
PADCTRL0_LDODEN | PADCTRL0_PWENC | PADCTRL0_PWEND |
PADCTRL0_PWENG | PADCTRL0_CKEN | PADCTRL0_TXEN);
HDMI_WRITE(sc, HDMI_PADCTRL1, PADCTRL1_AMP_OPT | PADCTRL1_AMPCK_OPT |
PADCTRL1_EMP_OPT | PADCTRL1_EMPCK_OPT | PADCTRL1_REG_DEN |
PADCTRL1_REG_DENCK | PADCTRL1_REG_EMP_EN | PADCTRL1_REG_AMP_EN);
/* Select PLL3 as input clock */
HDMI_WRITE(sc, HDMI_PLLDBG0, PLLDBG0_CKIN_SEL_PLL3);
DELAY(HDMI_ENABLE_DELAY);
}
static void
a10hdmi_hpd(void *arg)
{
struct a10hdmi_softc *sc;
device_t dev;
uint32_t hpd;
dev = arg;
sc = device_get_softc(dev);
hpd = HDMI_READ(sc, HDMI_HPD);
if ((hpd & HPD_DET) == HPD_DET)
EVENTHANDLER_INVOKE(hdmi_event, dev, HDMI_EVENT_CONNECTED);
config_intrhook_disestablish(&sc->mode_hook);
}
static int
a10hdmi_probe(device_t dev)
{
if (!ofw_bus_status_okay(dev))
return (ENXIO);
if (!ofw_bus_is_compatible(dev, "allwinner,sun7i-a20-hdmi"))
return (ENXIO);
device_set_desc(dev, "Allwinner HDMI TX");
return (BUS_PROBE_DEFAULT);
}
static int
a10hdmi_attach(device_t dev)
{
struct a10hdmi_softc *sc;
int error;
sc = device_get_softc(dev);
if (bus_alloc_resources(dev, a10hdmi_spec, &sc->res)) {
device_printf(dev, "cannot allocate resources for device\n");
return (ENXIO);
}
/* Setup clocks */
error = clk_get_by_ofw_name(dev, 0, "ahb", &sc->clk_ahb);
if (error != 0) {
device_printf(dev, "cannot find ahb clock\n");
return (error);
}
error = clk_get_by_ofw_name(dev, 0, "hdmi", &sc->clk_hdmi);
if (error != 0) {
device_printf(dev, "cannot find hdmi clock\n");
return (error);
}
error = clk_get_by_ofw_name(dev, 0, "lcd", &sc->clk_lcd);
if (error != 0) {
device_printf(dev, "cannot find lcd clock\n");
}
/* Enable HDMI clock */
error = clk_enable(sc->clk_hdmi);
if (error != 0) {
device_printf(dev, "cannot enable hdmi clock\n");
return (error);
}
/* Gating AHB clock for HDMI */
error = clk_enable(sc->clk_ahb);
if (error != 0) {
device_printf(dev, "cannot enable ahb gate\n");
return (error);
}
a10hdmi_init(sc);
sc->mode_hook.ich_func = a10hdmi_hpd;
sc->mode_hook.ich_arg = dev;
error = config_intrhook_establish(&sc->mode_hook);
if (error != 0)
return (error);
return (0);
}
static int
a10hdmi_ddc_xfer(struct a10hdmi_softc *sc, uint16_t addr, uint8_t seg,
uint8_t off, int len)
{
uint32_t val;
int retry;
/* Set FIFO direction to read */
val = HDMI_READ(sc, DDC_CTRL);
val &= ~CTRL_DDC_FIFO_DIR;
val |= CTRL_DDC_FIFO_DIR_READ;
HDMI_WRITE(sc, DDC_CTRL, val);
/* Setup DDC slave address */
val = (addr << SLAVE_ADDR_SHIFT) | (seg << SLAVE_ADDR_SEG_SHIFT) |
(EDDC_ADDR << SLAVE_ADDR_EDDC_SHIFT) |
(off << SLAVE_ADDR_OFFSET_SHIFT);
HDMI_WRITE(sc, DDC_SLAVE_ADDR, val);
/* Clear FIFO */
val = HDMI_READ(sc, DDC_FIFO_CTRL);
val |= FIFO_CTRL_CLEAR;
HDMI_WRITE(sc, DDC_FIFO_CTRL, val);
/* Set transfer length */
HDMI_WRITE(sc, DDC_BYTE_COUNTER, len);
/* Set command to "Explicit Offset Address Read" */
HDMI_WRITE(sc, DDC_COMMAND, COMMAND_EOREAD);
/* Start transfer */
val = HDMI_READ(sc, DDC_CTRL);
val |= CTRL_DDC_ACMD_START;
HDMI_WRITE(sc, DDC_CTRL, val);
/* Wait for command to start */
retry = DDC_RETRY;
while (--retry > 0) {
val = HDMI_READ(sc, DDC_CTRL);
if ((val & CTRL_DDC_ACMD_START) == 0)
break;
DELAY(DDC_DELAY);
}
if (retry == 0)
return (ETIMEDOUT);
/* Ensure that the transfer completed */
val = HDMI_READ(sc, DDC_INT_STATUS);
if ((val & INT_STATUS_XFER_DONE) == 0)
return (EIO);
return (0);
}
static int
a10hdmi_ddc_read(struct a10hdmi_softc *sc, int block, uint8_t *edid)
{
int resid, off, len, error;
uint8_t *pbuf;
pbuf = edid;
resid = EDID_LENGTH;
off = (block & 1) ? EDID_LENGTH : 0;
while (resid > 0) {
len = min(resid, DDC_BLKLEN);
error = a10hdmi_ddc_xfer(sc, DDC_ADDR, block >> 1, off, len);
if (error != 0)
return (error);
bus_read_multi_1(sc->res, DDC_FIFO, pbuf, len);
pbuf += len;
off += len;
resid -= len;
}
return (0);
}
static int
a10hdmi_detect_hdmi_vsdb(uint8_t *edid)
{
int off, p, btag, blen;
if (edid[EXT_TAG] != CEA_TAG_ID)
return (0);
off = edid[CEA_DATA_OFF];
/* CEA data block collection starts at byte 4 */
if (off <= CEA_DATA_START)
return (0);
/* Parse the CEA data blocks */
for (p = CEA_DATA_START; p < off;) {
btag = BLOCK_TAG(edid[p]);
blen = BLOCK_LEN(edid[p]);
/* Make sure the length is sane */
if (p + blen + 1 > off)
break;
/* Look for a VSDB with the HDMI 24-bit IEEE registration ID */
if (btag == BLOCK_TAG_VSDB && blen >= HDMI_VSDB_MINLEN &&
memcmp(&edid[p + 1], HDMI_OUI, HDMI_OUI_LEN) == 0)
return (1);
/* Next data block */
p += (1 + blen);
}
return (0);
}
static void
a10hdmi_detect_hdmi(struct a10hdmi_softc *sc, int *phdmi, int *paudio)
{
struct edid_info ei;
uint8_t edid[EDID_LENGTH];
int block;
*phdmi = *paudio = 0;
if (edid_parse(sc->edid, &ei) != 0)
return;
/* Scan through extension blocks, looking for a CEA-861 block. */
for (block = 1; block <= ei.edid_ext_block_count; block++) {
if (a10hdmi_ddc_read(sc, block, edid) != 0)
return;
if (a10hdmi_detect_hdmi_vsdb(edid) != 0) {
*phdmi = 1;
*paudio = ((edid[CEA_DTD] & DTD_BASIC_AUDIO) != 0);
return;
}
}
}
static int
a10hdmi_get_edid(device_t dev, uint8_t **edid, uint32_t *edid_len)
{
struct a10hdmi_softc *sc;
int error, retry;
sc = device_get_softc(dev);
retry = DDC_READ_RETRY;
while (--retry > 0) {
/* I2C software reset */
HDMI_WRITE(sc, DDC_FIFO_CTRL, 0);
HDMI_WRITE(sc, DDC_CTRL, CTRL_DDC_EN | CTRL_DDC_SWRST);
DELAY(SWRST_DELAY);
if (HDMI_READ(sc, DDC_CTRL) & CTRL_DDC_SWRST) {
device_printf(dev, "DDC software reset failed\n");
return (ENXIO);
}
/* Configure DDC clock */
HDMI_WRITE(sc, DDC_CLOCK, DDC_CLOCK_M | DDC_CLOCK_N);
/* Enable SDA/SCL */
HDMI_WRITE(sc, DDC_CTRL_LINE,
DDC_LINE_SCL_ENABLE | DDC_LINE_SDA_ENABLE);
/* Read EDID block */
error = a10hdmi_ddc_read(sc, 0, sc->edid);
if (error == 0) {
*edid = sc->edid;
*edid_len = sizeof(sc->edid);
break;
}
}
if (error == 0)
a10hdmi_detect_hdmi(sc, &sc->has_hdmi, &sc->has_audio);
else
sc->has_hdmi = sc->has_audio = 0;
return (error);
}
static void
a10hdmi_set_audiomode(device_t dev, const struct videomode *mode)
{
struct a10hdmi_softc *sc;
uint32_t val;
int retry;
sc = device_get_softc(dev);
/* Disable and reset audio module and wait for reset bit to clear */
HDMI_WRITE(sc, HDMI_AUD_CTRL, AUD_CTRL_RST);
for (retry = HDMI_AUDIO_RESET_RETRY; retry > 0; retry--) {
val = HDMI_READ(sc, HDMI_AUD_CTRL);
if ((val & AUD_CTRL_RST) == 0)
break;
}
if (retry == 0) {
device_printf(dev, "timeout waiting for audio module\n");
return;
}
if (!sc->has_audio)
return;
/* DMA and FIFO control */
HDMI_WRITE(sc, HDMI_ADMA_CTRL, HDMI_ADMA_MODE_DDMA);
/* Audio format control (LPCM, S16LE, stereo) */
HDMI_WRITE(sc, HDMI_AUD_FMT, AUD_FMT_CH(HDMI_AUDIO_CHANNELS));
/* Channel mappings */
HDMI_WRITE(sc, HDMI_PCM_CTRL, HDMI_AUDIO_CHANNELMAP);
/* Clocks */
HDMI_WRITE(sc, HDMI_AUD_CTS,
HDMI_AUDIO_CTS(mode->dot_clock, HDMI_AUDIO_N));
HDMI_WRITE(sc, HDMI_AUD_N, HDMI_AUDIO_N);
/* Set sampling frequency to 48 kHz, word length to 16-bit */
HDMI_WRITE(sc, HDMI_AUD_CH_STATUS0, CH_STATUS0_FS_FREQ_48);
HDMI_WRITE(sc, HDMI_AUD_CH_STATUS1, CH_STATUS1_WORD_LEN_16);
/* Enable */
HDMI_WRITE(sc, HDMI_AUD_CTRL, AUD_CTRL_EN);
}
static int
a10hdmi_get_tcon_config(struct a10hdmi_softc *sc, int *div, int *dbl)
{
uint64_t lcd_fin, lcd_fout;
clk_t clk_lcd_parent;
const char *pname;
int error;
error = clk_get_parent(sc->clk_lcd, &clk_lcd_parent);
if (error != 0)
return (error);
/* Get the LCD CH1 special clock 2 divider */
error = clk_get_freq(sc->clk_lcd, &lcd_fout);
if (error != 0)
return (error);
error = clk_get_freq(clk_lcd_parent, &lcd_fin);
if (error != 0)
return (error);
*div = lcd_fin / lcd_fout;
/* Detect LCD CH1 special clock using a 1X or 2X source */
/* XXX */
pname = clk_get_name(clk_lcd_parent);
if (strcmp(pname, "pll3") == 0 || strcmp(pname, "pll7") == 0)
*dbl = 0;
else
*dbl = 1;
return (0);
}
static int
a10hdmi_set_videomode(device_t dev, const struct videomode *mode)
{
struct a10hdmi_softc *sc;
int error, clk_div, clk_dbl;
int dblscan, hfp, hspw, hbp, vfp, vspw, vbp;
uint32_t val;
sc = device_get_softc(dev);
dblscan = !!(mode->flags & VID_DBLSCAN);
hfp = mode->hsync_start - mode->hdisplay;
hspw = mode->hsync_end - mode->hsync_start;
hbp = mode->htotal - mode->hsync_start;
vfp = mode->vsync_start - mode->vdisplay;
vspw = mode->vsync_end - mode->vsync_start;
vbp = mode->vtotal - mode->vsync_start;
error = a10hdmi_get_tcon_config(sc, &clk_div, &clk_dbl);
if (error != 0) {
device_printf(dev, "couldn't get tcon config: %d\n", error);
return (error);
}
/* Clear interrupt status */
HDMI_WRITE(sc, HDMI_INT_STATUS, HDMI_READ(sc, HDMI_INT_STATUS));
/* Clock setup */
val = HDMI_READ(sc, HDMI_PADCTRL1);
val &= ~PADCTRL1_REG_CKSS;
val |= (clk_dbl ? PADCTRL1_REG_CKSS_2X : PADCTRL1_REG_CKSS_1X);
HDMI_WRITE(sc, HDMI_PADCTRL1, val);
HDMI_WRITE(sc, HDMI_PLLCTRL0, PLLCTRL0_PLL_EN | PLLCTRL0_BWS |
PLLCTRL0_HV_IS_33 | PLLCTRL0_LDO1_EN | PLLCTRL0_LDO2_EN |
PLLCTRL0_SDIV2 | PLLCTRL0_VCO_GAIN | PLLCTRL0_S |
PLLCTRL0_CP_S | PLLCTRL0_CS | PLLCTRL0_PREDIV(clk_div) |
PLLCTRL0_VCO_S);
/* Setup display settings */
if (bootverbose)
device_printf(dev, "HDMI: %s, Audio: %s\n",
sc->has_hdmi ? "yes" : "no", sc->has_audio ? "yes" : "no");
val = 0;
if (sc->has_hdmi)
val |= VID_CTRL_HDMI_MODE;
if (mode->flags & VID_INTERLACE)
val |= VID_CTRL_INTERLACE;
if (mode->flags & VID_DBLSCAN)
val |= VID_CTRL_REPEATER_2X;
HDMI_WRITE(sc, HDMI_VID_CTRL, val);
/* Setup display timings */
HDMI_WRITE(sc, HDMI_VID_TIMING0,
VID_ACT_V(mode->vdisplay) | VID_ACT_H(mode->hdisplay << dblscan));
HDMI_WRITE(sc, HDMI_VID_TIMING1,
VID_VBP(vbp) | VID_HBP(hbp << dblscan));
HDMI_WRITE(sc, HDMI_VID_TIMING2,
VID_VFP(vfp) | VID_HFP(hfp << dblscan));
HDMI_WRITE(sc, HDMI_VID_TIMING3,
VID_VSPW(vspw) | VID_HSPW(hspw << dblscan));
val = TX_CLOCK_NORMAL;
if (mode->flags & VID_PVSYNC)
val |= VID_VSYNC_ACTSEL;
if (mode->flags & VID_PHSYNC)
val |= VID_HSYNC_ACTSEL;
HDMI_WRITE(sc, HDMI_VID_TIMING4, val);
/* This is an ordered list of infoframe packets that the HDMI
* transmitter will send. Transmit packets in the following order:
* 1. General control packet
* 2. AVI infoframe
* 3. Audio infoframe
* There are 2 registers with 4 slots each. The list is terminated
* with the special PKT_END marker.
*/
HDMI_WRITE(sc, HDMI_PKTCTRL0,
PKTCTRL_PACKET(0, PKT_GC) | PKTCTRL_PACKET(1, PKT_AVI) |
PKTCTRL_PACKET(2, PKT_AI) | PKTCTRL_PACKET(3, PKT_END));
HDMI_WRITE(sc, HDMI_PKTCTRL1, 0);
/* Setup audio */
a10hdmi_set_audiomode(dev, mode);
return (0);
}
static int
a10hdmi_enable(device_t dev, int onoff)
{
struct a10hdmi_softc *sc;
uint32_t val;
sc = device_get_softc(dev);
/* Enable or disable video output */
val = HDMI_READ(sc, HDMI_VID_CTRL);
if (onoff)
val |= VID_CTRL_VIDEO_EN;
else
val &= ~VID_CTRL_VIDEO_EN;
HDMI_WRITE(sc, HDMI_VID_CTRL, val);
return (0);
}
static device_method_t a10hdmi_methods[] = {
/* Device interface */
DEVMETHOD(device_probe, a10hdmi_probe),
DEVMETHOD(device_attach, a10hdmi_attach),
/* HDMI interface */
DEVMETHOD(hdmi_get_edid, a10hdmi_get_edid),
DEVMETHOD(hdmi_set_videomode, a10hdmi_set_videomode),
DEVMETHOD(hdmi_enable, a10hdmi_enable),
DEVMETHOD_END
};
static driver_t a10hdmi_driver = {
"a10hdmi",
a10hdmi_methods,
sizeof(struct a10hdmi_softc),
};
static devclass_t a10hdmi_devclass;
DRIVER_MODULE(a10hdmi, simplebus, a10hdmi_driver, a10hdmi_devclass, 0, 0);
MODULE_VERSION(a10hdmi, 1);