1438 lines
42 KiB
Groff
1438 lines
42 KiB
Groff
.\" Copyright (c) 1983, 1991, 1993
|
|
.\" The Regents of the University of California. All rights reserved.
|
|
.\"
|
|
.\" Redistribution and use in source and binary forms, with or without
|
|
.\" modification, are permitted provided that the following conditions
|
|
.\" are met:
|
|
.\" 1. Redistributions of source code must retain the above copyright
|
|
.\" notice, this list of conditions and the following disclaimer.
|
|
.\" 2. Redistributions in binary form must reproduce the above copyright
|
|
.\" notice, this list of conditions and the following disclaimer in the
|
|
.\" documentation and/or other materials provided with the distribution.
|
|
.\" 4. Neither the name of the University nor the names of its contributors
|
|
.\" may be used to endorse or promote products derived from this software
|
|
.\" without specific prior written permission.
|
|
.\"
|
|
.\" THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND
|
|
.\" ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
.\" IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
.\" ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE
|
|
.\" FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
.\" DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
.\" OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
.\" HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
.\" LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
.\" OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
.\" SUCH DAMAGE.
|
|
.\"
|
|
.\" From: @(#)ifconfig.8 8.3 (Berkeley) 1/5/94
|
|
.\" $FreeBSD$
|
|
.\"
|
|
.Dd February 27, 2006
|
|
.Dt IFCONFIG 8
|
|
.Os
|
|
.Sh NAME
|
|
.Nm ifconfig
|
|
.Nd configure network interface parameters
|
|
.Sh SYNOPSIS
|
|
.Nm
|
|
.Op Fl L
|
|
.Op Fl k
|
|
.Op Fl m
|
|
.Ar interface
|
|
.Op Cm create
|
|
.Op Ar address_family
|
|
.Oo
|
|
.Ar address
|
|
.Op Ar dest_address
|
|
.Oc
|
|
.Op Ar parameters
|
|
.Nm
|
|
.Ar interface
|
|
.Cm destroy
|
|
.Nm
|
|
.Fl a
|
|
.Op Fl L
|
|
.Op Fl d
|
|
.Op Fl m
|
|
.Op Fl u
|
|
.Op Fl v
|
|
.Op Ar address_family
|
|
.Nm
|
|
.Fl l
|
|
.Op Fl d
|
|
.Op Fl u
|
|
.Op Ar address_family
|
|
.Nm
|
|
.Op Fl L
|
|
.Op Fl d
|
|
.Op Fl k
|
|
.Op Fl m
|
|
.Op Fl u
|
|
.Op Fl v
|
|
.Op Fl C
|
|
.Sh DESCRIPTION
|
|
The
|
|
.Nm
|
|
utility is used to assign an address
|
|
to a network interface and/or configure
|
|
network interface parameters.
|
|
The
|
|
.Nm
|
|
utility must be used at boot time to define the network address
|
|
of each interface present on a machine; it may also be used at
|
|
a later time to redefine an interface's address
|
|
or other operating parameters.
|
|
.Pp
|
|
The following options are available:
|
|
.Bl -tag -width indent
|
|
.It Ar address
|
|
For the
|
|
.Tn DARPA Ns -Internet
|
|
family,
|
|
the address is either a host name present in the host name data
|
|
base,
|
|
.Xr hosts 5 ,
|
|
or a
|
|
.Tn DARPA
|
|
Internet address expressed in the Internet standard
|
|
.Dq dot notation .
|
|
.Pp
|
|
It is also possible to use the CIDR notation (also known as the
|
|
slash notation) to include the netmask.
|
|
That is, one can specify an address like
|
|
.Li 192.168.0.1/16 .
|
|
.Pp
|
|
For
|
|
.Dq inet6
|
|
family, it is also possible to specify the prefix length using the slash
|
|
notation, like
|
|
.Li ::1/128 .
|
|
See the
|
|
.Cm prefixlen
|
|
parameter below for more information.
|
|
.\" For the Xerox Network Systems(tm) family,
|
|
.\" addresses are
|
|
.\" .Ar net:a.b.c.d.e.f ,
|
|
.\" where
|
|
.\" .Ar net
|
|
.\" is the assigned network number (in decimal),
|
|
.\" and each of the six bytes of the host number,
|
|
.\" .Ar a
|
|
.\" through
|
|
.\" .Ar f ,
|
|
.\" are specified in hexadecimal.
|
|
.\" The host number may be omitted on IEEE 802 protocol
|
|
.\" (Ethernet, FDDI, and Token Ring) interfaces,
|
|
.\" which use the hardware physical address,
|
|
.\" and on interfaces other than the first.
|
|
.\" For the
|
|
.\" .Tn ISO
|
|
.\" family, addresses are specified as a long hexadecimal string,
|
|
.\" as in the Xerox family.
|
|
.\" However, two consecutive dots imply a zero
|
|
.\" byte, and the dots are optional, if the user wishes to (carefully)
|
|
.\" count out long strings of digits in network byte order.
|
|
.Pp
|
|
The link-level
|
|
.Pq Dq link
|
|
address
|
|
is specified as a series of colon-separated hex digits.
|
|
This can be used to
|
|
e.g.\& set a new MAC address on an ethernet interface, though the
|
|
mechanism used is not ethernet-specific.
|
|
If the interface is already
|
|
up when this option is used, it will be briefly brought down and
|
|
then brought back up again in order to ensure that the receive
|
|
filter in the underlying ethernet hardware is properly reprogrammed.
|
|
.It Ar address_family
|
|
Specify the
|
|
address family
|
|
which affects interpretation of the remaining parameters.
|
|
Since an interface can receive transmissions in differing protocols
|
|
with different naming schemes, specifying the address family is recommended.
|
|
The address or protocol families currently
|
|
supported are
|
|
.Dq inet ,
|
|
.Dq inet6 ,
|
|
.Dq atalk ,
|
|
.Dq ipx ,
|
|
.\" .Dq iso ,
|
|
and
|
|
.Dq link .
|
|
.\" and
|
|
.\" .Dq ns .
|
|
The default is
|
|
.Dq inet .
|
|
.Dq ether
|
|
and
|
|
.Dq lladdr
|
|
are synonyms for
|
|
.Dq link .
|
|
.It Ar dest_address
|
|
Specify the address of the correspondent on the other end
|
|
of a point to point link.
|
|
.It Ar interface
|
|
This
|
|
parameter is a string of the form
|
|
.Dq name unit ,
|
|
for example,
|
|
.Dq Li ed0 .
|
|
.El
|
|
.Pp
|
|
The following parameters may be set with
|
|
.Nm :
|
|
.Bl -tag -width indent
|
|
.It Cm add
|
|
Another name for the
|
|
.Cm alias
|
|
parameter.
|
|
Introduced for compatibility
|
|
with
|
|
.Bsx .
|
|
.It Cm alias
|
|
Establish an additional network address for this interface.
|
|
This is sometimes useful when changing network numbers, and
|
|
one wishes to accept packets addressed to the old interface.
|
|
If the address is on the same subnet as the first network address
|
|
for this interface, a non-conflicting netmask must be given.
|
|
Usually
|
|
.Li 0xffffffff
|
|
is most appropriate.
|
|
.It Fl alias
|
|
Remove the network address specified.
|
|
This would be used if you incorrectly specified an alias, or it
|
|
was no longer needed.
|
|
If you have incorrectly set an NS address having the side effect
|
|
of specifying the host portion, removing all NS addresses will
|
|
allow you to respecify the host portion.
|
|
.It Cm anycast
|
|
(Inet6 only.)
|
|
Specify that the address configured is an anycast address.
|
|
Based on the current specification,
|
|
only routers may configure anycast addresses.
|
|
Anycast address will not be used as source address of any of outgoing
|
|
IPv6 packets.
|
|
.It Cm arp
|
|
Enable the use of the Address Resolution Protocol
|
|
.Pq Xr arp 4
|
|
in mapping
|
|
between network level addresses and link level addresses (default).
|
|
This is currently implemented for mapping between
|
|
.Tn DARPA
|
|
Internet
|
|
addresses and
|
|
.Tn IEEE
|
|
802 48-bit MAC addresses (Ethernet, FDDI, and Token Ring addresses).
|
|
.It Fl arp
|
|
Disable the use of the Address Resolution Protocol
|
|
.Pq Xr arp 4 .
|
|
.It Cm staticarp
|
|
If the Address Resolution Protocol is enabled,
|
|
the host will only reply to requests for its addresses,
|
|
and will never send any requests.
|
|
.It Fl staticarp
|
|
If the Address Resolution Protocol is enabled,
|
|
the host will perform normally,
|
|
sending out requests and listening for replies.
|
|
.It Cm broadcast
|
|
(Inet only.)
|
|
Specify the address to use to represent broadcasts to the
|
|
network.
|
|
The default broadcast address is the address with a host part of all 1's.
|
|
.It Cm debug
|
|
Enable driver dependent debugging code; usually, this turns on
|
|
extra console error logging.
|
|
.It Fl debug
|
|
Disable driver dependent debugging code.
|
|
.It Cm promisc
|
|
Put interface into permanently promiscuous mode.
|
|
.It Fl promisc
|
|
Disable permanently promiscuous mode.
|
|
.It Cm delete
|
|
Another name for the
|
|
.Fl alias
|
|
parameter.
|
|
.It Cm down
|
|
Mark an interface
|
|
.Dq down .
|
|
When an interface is marked
|
|
.Dq down ,
|
|
the system will not attempt to
|
|
transmit messages through that interface.
|
|
If possible, the interface will be reset to disable reception as well.
|
|
This action does not automatically disable routes using the interface.
|
|
.It Cm eui64
|
|
(Inet6 only.)
|
|
Fill interface index
|
|
(lowermost 64bit of an IPv6 address)
|
|
automatically.
|
|
.It Cm ipdst
|
|
This is used to specify an Internet host who is willing to receive
|
|
IP packets encapsulating IPX packets bound for a remote network.
|
|
An apparent point to point link is constructed, and
|
|
the address specified will be taken as the IPX address and network
|
|
of the destination.
|
|
.It Cm maclabel Ar label
|
|
If Mandatory Access Control support is enabled in the kernel,
|
|
set the MAC label to
|
|
.Ar label .
|
|
.\" (see
|
|
.\" .Xr maclabel 7 ) .
|
|
.It Cm media Ar type
|
|
If the driver supports the media selection system, set the media type
|
|
of the interface to
|
|
.Ar type .
|
|
Some interfaces support the mutually exclusive use of one of several
|
|
different physical media connectors.
|
|
For example, a 10Mbit/s Ethernet
|
|
interface might support the use of either
|
|
.Tn AUI
|
|
or twisted pair connectors.
|
|
Setting the media type to
|
|
.Cm 10base5/AUI
|
|
would change the currently active connector to the AUI port.
|
|
Setting it to
|
|
.Cm 10baseT/UTP
|
|
would activate twisted pair.
|
|
Refer to the interfaces' driver
|
|
specific documentation or man page for a complete list of the
|
|
available types.
|
|
.It Cm mediaopt Ar opts
|
|
If the driver supports the media selection system, set the specified
|
|
media options on the interface.
|
|
The
|
|
.Ar opts
|
|
argument
|
|
is a comma delimited list of options to apply to the interface.
|
|
Refer to the interfaces' driver specific man page for a complete
|
|
list of available options.
|
|
.It Fl mediaopt Ar opts
|
|
If the driver supports the media selection system, disable the
|
|
specified media options on the interface.
|
|
.It Cm mode Ar mode
|
|
If the driver supports the media selection system, set the specified
|
|
operating mode on the interface to
|
|
.Ar mode .
|
|
For IEEE 802.11 wireless interfaces that support multiple operating modes
|
|
this directive is used to select between 802.11a
|
|
.Pq Cm 11a ,
|
|
802.11b
|
|
.Pq Cm 11b ,
|
|
and 802.11g
|
|
.Pq Cm 11g
|
|
operating modes.
|
|
.It Cm name Ar name
|
|
Set the interface name to
|
|
.Ar name .
|
|
.It Cm rxcsum , txcsum
|
|
If the driver supports user-configurable checksum offloading,
|
|
enable receive (or transmit) checksum offloading on the interface.
|
|
Some drivers may not be able to enable these flags independently
|
|
of each other, so setting one may also set the other.
|
|
The driver will offload as much checksum work as it can reliably
|
|
support, the exact level of offloading varies between drivers.
|
|
.It Fl rxcsum , txcsum
|
|
If the driver supports user-configurable checksum offloading,
|
|
disable receive (or transmit) checksum offloading on the interface.
|
|
These settings may not always be independent of each other.
|
|
.It Cm vlanmtu , vlanhwtag
|
|
If the driver offers user-configurable VLAN support, enable
|
|
reception of extended frames or tag processing in hardware,
|
|
respectively.
|
|
Note that this must be issued on a physical interface associated with
|
|
.Xr vlan 4 ,
|
|
not on a
|
|
.Xr vlan 4
|
|
interface itself.
|
|
.It Fl vlanmtu , vlanhwtag
|
|
If the driver offers user-configurable VLAN support, disable
|
|
reception of extended frames or tag processing in hardware,
|
|
respectively.
|
|
.It Cm polling
|
|
Turn on
|
|
.Xr polling 4
|
|
feature and disable interrupts on the interface, if driver supports
|
|
this mode.
|
|
.It Fl polling
|
|
Turn off
|
|
.Xr polling 4
|
|
feature and enable interrupt mode on the interface.
|
|
.It Cm create
|
|
Create the specified network pseudo-device.
|
|
If the interface is given without a unit number, try to create a new
|
|
device with an arbitrary unit number.
|
|
If creation of an arbitrary device is successful, the new device name is
|
|
printed to standard output unless the interface is renamed or destroyed
|
|
in the same
|
|
.Nm
|
|
invocation.
|
|
.It Cm destroy
|
|
Destroy the specified network pseudo-device.
|
|
.It Cm plumb
|
|
Another name for the
|
|
.Cm create
|
|
parameter.
|
|
Included for
|
|
.Tn Solaris
|
|
compatibility.
|
|
.It Cm unplumb
|
|
Another name for the
|
|
.Cm destroy
|
|
parameter.
|
|
Included for
|
|
.Tn Solaris
|
|
compatibility.
|
|
.It Cm metric Ar n
|
|
Set the routing metric of the interface to
|
|
.Ar n ,
|
|
default 0.
|
|
The routing metric is used by the routing protocol
|
|
.Pq Xr routed 8 .
|
|
Higher metrics have the effect of making a route
|
|
less favorable; metrics are counted as addition hops
|
|
to the destination network or host.
|
|
.It Cm mtu Ar n
|
|
Set the maximum transmission unit of the interface to
|
|
.Ar n ,
|
|
default is interface specific.
|
|
The MTU is used to limit the size of packets that are transmitted on an
|
|
interface.
|
|
Not all interfaces support setting the MTU, and some interfaces have
|
|
range restrictions.
|
|
.It Cm netmask Ar mask
|
|
.\" (Inet and ISO.)
|
|
(Inet only.)
|
|
Specify how much of the address to reserve for subdividing
|
|
networks into sub-networks.
|
|
The mask includes the network part of the local address
|
|
and the subnet part, which is taken from the host field of the address.
|
|
The mask can be specified as a single hexadecimal number
|
|
with a leading
|
|
.Ql 0x ,
|
|
with a dot-notation Internet address,
|
|
or with a pseudo-network name listed in the network table
|
|
.Xr networks 5 .
|
|
The mask contains 1's for the bit positions in the 32-bit address
|
|
which are to be used for the network and subnet parts,
|
|
and 0's for the host part.
|
|
The mask should contain at least the standard network portion,
|
|
and the subnet field should be contiguous with the network
|
|
portion.
|
|
.Pp
|
|
The netmask can also be specified in CIDR notation after the address.
|
|
See the
|
|
.Ar address
|
|
option above for more information.
|
|
.It Cm prefixlen Ar len
|
|
(Inet6 only.)
|
|
Specify that
|
|
.Ar len
|
|
bits are reserved for subdividing networks into sub-networks.
|
|
The
|
|
.Ar len
|
|
must be integer, and for syntactical reason it must be between 0 to 128.
|
|
It is almost always 64 under the current IPv6 assignment rule.
|
|
If the parameter is omitted, 64 is used.
|
|
.Pp
|
|
The prefix can also be specified using the slash notation after the address.
|
|
See the
|
|
.Ar address
|
|
option above for more information.
|
|
.\" see
|
|
.\" Xr eon 5 .
|
|
.\" .It Cm nsellength Ar n
|
|
.\" .Pf ( Tn ISO
|
|
.\" only)
|
|
.\" This specifies a trailing number of bytes for a received
|
|
.\" .Tn NSAP
|
|
.\" used for local identification, the remaining leading part of which is
|
|
.\" taken to be the
|
|
.\" .Tn NET
|
|
.\" (Network Entity Title).
|
|
.\" The default value is 1, which is conformant to US
|
|
.\" .Tn GOSIP .
|
|
.\" When an ISO address is set in an ifconfig command,
|
|
.\" it is really the
|
|
.\" .Tn NSAP
|
|
.\" which is being specified.
|
|
.\" For example, in
|
|
.\" .Tn US GOSIP ,
|
|
.\" 20 hex digits should be
|
|
.\" specified in the
|
|
.\" .Tn ISO NSAP
|
|
.\" to be assigned to the interface.
|
|
.\" There is some evidence that a number different from 1 may be useful
|
|
.\" for
|
|
.\" .Tn AFI
|
|
.\" 37 type addresses.
|
|
.It Cm range Ar netrange
|
|
Under appletalk, set the interface to respond to a
|
|
.Ar netrange
|
|
of the form
|
|
.Ar startnet Ns - Ns Ar endnet .
|
|
Appletalk uses this scheme instead of
|
|
netmasks though
|
|
.Fx
|
|
implements it internally as a set of netmasks.
|
|
.It Cm remove
|
|
Another name for the
|
|
.Fl alias
|
|
parameter.
|
|
Introduced for compatibility
|
|
with
|
|
.Bsx .
|
|
.It Cm phase
|
|
The argument following this specifies the version (phase) of the
|
|
Appletalk network attached to the interface.
|
|
Values of 1 or 2 are permitted.
|
|
.Sm off
|
|
.It Cm link Op Cm 0 No - Cm 2
|
|
.Sm on
|
|
Enable special processing of the link level of the interface.
|
|
These three options are interface specific in actual effect, however,
|
|
they are in general used to select special modes of operation.
|
|
An example
|
|
of this is to enable SLIP compression, or to select the connector type
|
|
for some Ethernet cards.
|
|
Refer to the man page for the specific driver
|
|
for more information.
|
|
.Sm off
|
|
.It Fl link Op Cm 0 No - Cm 2
|
|
.Sm on
|
|
Disable special processing at the link level with the specified interface.
|
|
.It Cm monitor
|
|
Put the interface in monitor mode.
|
|
No packets are transmitted, and received packets are discarded after
|
|
.Xr bpf 4
|
|
processing.
|
|
.It Fl monitor
|
|
Take the interface out of monitor mode.
|
|
.It Cm up
|
|
Mark an interface
|
|
.Dq up .
|
|
This may be used to enable an interface after an
|
|
.Dq Nm Cm down .
|
|
It happens automatically when setting the first address on an interface.
|
|
If the interface was reset when previously marked down,
|
|
the hardware will be re-initialized.
|
|
.El
|
|
.Pp
|
|
The following parameters are specific to IEEE 802.11 wireless interfaces:
|
|
.Bl -tag -width indent
|
|
.It Cm apbridge
|
|
When operating as an access point, pass packets between
|
|
wireless clients directly (default).
|
|
To instead let them pass up through the
|
|
system and be forwarded using some other mechanism, use
|
|
.Fl apbridge .
|
|
Disabling the internal bridging
|
|
is useful when traffic is to be processed with
|
|
packet filtering.
|
|
.It Cm authmode Ar mode
|
|
Set the desired authentication mode in infrastructure mode.
|
|
Not all adaptors support all modes.
|
|
The set of
|
|
valid modes is
|
|
.Cm none , open , shared
|
|
(shared key),
|
|
.Cm 8021x
|
|
(IEEE 802.1x),
|
|
and
|
|
.Cm wpa
|
|
(IEEE WPA/WPA2/802.11i).
|
|
The
|
|
.Cm 8021x
|
|
and
|
|
.Cm wpa
|
|
modes are only useful when using an authentication service
|
|
(a supplicant for client operation or an authenticator when
|
|
operating as an access point).
|
|
Modes are case insensitive.
|
|
.It Cm bintval Ar interval
|
|
Set the interval at which beacon frames are sent when operating in
|
|
ad-hoc or ap mode.
|
|
The
|
|
.Ar interval
|
|
parameter is specified in TU's (1/1024 msecs).
|
|
By default beacon frames are transmitted every 100 TU's.
|
|
.It Cm bssid Ar address
|
|
Specify the MAC address of the access point to use when operating
|
|
as a station in a BSS network.
|
|
This overrides any automatic selection done by the system.
|
|
To disable a previously selected access point, supply
|
|
.Cm any , none ,
|
|
or
|
|
.Cm -
|
|
for the address.
|
|
This option is useful when more than one access points have the same SSID.
|
|
Another name for the
|
|
.Cm bssid
|
|
parameter is
|
|
.Cm ap .
|
|
.It Cm burst
|
|
Enable packet bursting.
|
|
Packet bursting is a transmission technique whereby the wireless
|
|
medium is acquired once to send multiple frames and the interframe
|
|
spacing is reduced.
|
|
This technique can significantly increase throughput by reducing
|
|
transmission overhead.
|
|
Packet bursting is supported by the 802.11e QoS specification
|
|
and some devices that do not support QoS may still be capable.
|
|
By default packet bursting is enabled if a device is capable
|
|
of doing it.
|
|
To disable packet bursting, use
|
|
.Fl burst .
|
|
.It Cm chanlist Ar channels
|
|
Set the desired channels to use when scanning for access
|
|
points, neighbors in an IBSS network, or looking for unoccupied
|
|
channels when operating as an access point.
|
|
The set of channels is specified as a comma-separated list with
|
|
each element in the list representing either a single channel number or a range
|
|
of the form
|
|
.Dq Li a-b .
|
|
Channel numbers must be in the range 1 to 255 and be permissible
|
|
according to the operating characteristics of the device.
|
|
.It Cm channel Ar number
|
|
Set a single desired channel.
|
|
Channels range from 1 to 255, but the exact selection available
|
|
depends on the region your adaptor was manufactured for.
|
|
Setting
|
|
the channel to
|
|
.Li 0 ,
|
|
.Cm any ,
|
|
or
|
|
.Cm -
|
|
will give you the default for your adaptor.
|
|
Some
|
|
adaptors ignore this setting unless you are in ad-hoc mode.
|
|
Alternatively the frequency, in megahertz, may be specified
|
|
instead of the channel number.
|
|
.It Cm deftxkey Ar index
|
|
Set the default key to use for transmission.
|
|
Typically this is only set when using WEP encryption.
|
|
The
|
|
.Cm weptxkey
|
|
is an alias for this request; it is provided for backwards compatibility.
|
|
.It Cm dtimperiod Ar period
|
|
Set the
|
|
DTIM
|
|
period for transmitting buffered multicast data frames when
|
|
operating in ap mode.
|
|
The
|
|
.Ar period
|
|
specifies the number of beacon intervals between DTIM
|
|
and must be in the range 1 to 15.
|
|
By default DTIM is 1 (i.e., DTIM occurs at each beacon).
|
|
.It Cm fragthreshold Ar length
|
|
Set the threshold for which transmitted frames are broken into fragments.
|
|
The
|
|
.Ar length
|
|
argument is the frame size in bytes and must be in the range 256 to 2346.
|
|
Setting
|
|
.Ar length
|
|
to
|
|
.Li 2346 ,
|
|
.Cm any ,
|
|
or
|
|
.Cm -
|
|
disables transmit fragmentation.
|
|
Not all adaptors honor the fragmentation threshold.
|
|
.It Cm hidessid
|
|
When operating as an access point, do not broadcast the SSID
|
|
in beacon frames or respond to probe request frames unless
|
|
they are directed to the ap (i.e., they include the ap's SSID).
|
|
By default, the SSID is included in beacon frames and
|
|
undirected probe request frames are answered.
|
|
To re-enable the broadcast of the SSID etc., use
|
|
.Fl hidessid .
|
|
.It Cm list active
|
|
Display the list of channels available for use taking into account
|
|
any restrictions set with the
|
|
.Cm chanlist
|
|
directive.
|
|
See the description of
|
|
.Cm list chan
|
|
for more information.
|
|
.It Cm list caps
|
|
Display the adaptor's capabilities, including the operating
|
|
modes supported.
|
|
.It Cm list chan
|
|
Display the list of channels available for use.
|
|
Channels are shown with their IEEE channel number, equivalent
|
|
frequency, and usage modes.
|
|
Channels identified as
|
|
.Ql 11g
|
|
are also usable in
|
|
.Ql 11b
|
|
mode.
|
|
Channels identified as
|
|
.Ql 11a Turbo
|
|
may be used only for Atheros' Static Turbo mode
|
|
.Pq specified with Cm mediaopt turbo .
|
|
Channels marked with a
|
|
.Ql *
|
|
have a regulatory constraint that they be passively scanned.
|
|
This means a station is not permitted to transmit on the channel until
|
|
it identifies the channel is being used for 802.11 communication;
|
|
typically by hearing a beacon frame from an access point operating
|
|
on the channel.
|
|
.Cm list freq
|
|
is another way of requesting this information.
|
|
.It Cm list mac
|
|
Display the current MAC Access Control List state.
|
|
Each address is prefixed with a character that indicates the
|
|
current policy applied to it:
|
|
.Ql +
|
|
indicates the address is allowed access,
|
|
.Ql -
|
|
indicates the address is denied access,
|
|
.Ql *
|
|
indicates the address is present but the current policy open
|
|
(so the ACL is not consulted).
|
|
.It Cm list scan
|
|
Display the access points and/or ad-hoc neighbors
|
|
located in the vicinity.
|
|
This information may be updated automatically by the adaptor
|
|
and/or with a
|
|
.Cm scan
|
|
request.
|
|
.Cm list ap
|
|
is another way of requesting this information.
|
|
.It Cm list sta
|
|
When operating as an access point display the stations that are
|
|
currently associated.
|
|
When operating in ad-hoc mode display stations identified as
|
|
neighbors in the IBSS.
|
|
.It Cm list wme
|
|
Display the current parameters to use when operating in WME mode.
|
|
When WME mode is enabled for an adaptor this information will be
|
|
displayed with the regular status; this command is mostly useful
|
|
for examining parameters when WME mode is disabled.
|
|
See the description of the
|
|
.Cm wme
|
|
directive for information on the various parameters.
|
|
.It Cm mcastrate Ar rate
|
|
Set the rate for transmitting multicast/broadcast frames.
|
|
Rates are specified as megabits/second in decimal; e.g. 5.5 for 5.5 Mb/s.
|
|
This rate should be valid for the current operating conditions;
|
|
if an invalid rate is specified drivers are free to chose an
|
|
appropriate rate.
|
|
.It Cm powersave
|
|
Enable powersave operation.
|
|
When operating as a client, the station will conserve power by
|
|
periodically turning off the radio and listening for
|
|
messages from the access point telling it there are packets waiting.
|
|
The station must then retrieve the packets.
|
|
When operating as an access point, the station must honor power
|
|
save operation of associated clients.
|
|
Not all devices support power save operation, either as a client
|
|
or as an access point.
|
|
Use
|
|
.Fl powersave
|
|
to disable powersave operation.
|
|
.It Cm powersavesleep Ar sleep
|
|
Set the desired max powersave sleep time in milliseconds.
|
|
.It Cm protmode Ar technique
|
|
For interfaces operating in 802.11g, use the specified
|
|
.Ar technique
|
|
for protecting OFDM frames in a mixed 11b/11g network.
|
|
The set of valid techniques is
|
|
.Cm off , cts
|
|
(CTS to self),
|
|
and
|
|
.Cm rtscts
|
|
(RTS/CTS).
|
|
Technique names are case insensitive.
|
|
.It Cm pureg
|
|
When operating as an access point in 802.11g mode allow only
|
|
11g-capable stations to associate (11b-only stations are not
|
|
permitted to associate).
|
|
To allow both 11g and 11b-only stations to associate, use
|
|
.Fl pureg .
|
|
.It Cm roaming Ar mode
|
|
When operating as a station, control how the system will
|
|
behave when communication with the current access point
|
|
is broken.
|
|
The
|
|
.Ar mode
|
|
argument may be one of
|
|
.Cm device
|
|
(leave it to the hardware device to decide),
|
|
.Cm auto
|
|
(handle either in the device or the operating system\[em]as appropriate),
|
|
.Cm manual
|
|
(do nothing until explicitly instructed).
|
|
By default, the device is left to handle this if it is
|
|
capable; otherwise, the operating system will automatically
|
|
attempt to reestablish communication.
|
|
Manual mode is mostly useful when an application wants to
|
|
control the selection of an access point.
|
|
.It Cm rtsthreshold Ar length
|
|
Set the threshold for which
|
|
transmitted frames are preceded by transmission of an
|
|
RTS
|
|
control frame.
|
|
The
|
|
.Ar length
|
|
argument
|
|
is the frame size in bytes and must be in the range 1 to 2346.
|
|
Setting
|
|
.Ar length
|
|
to
|
|
.Li 2346 ,
|
|
.Cm any ,
|
|
or
|
|
.Cm -
|
|
disables transmission of RTS frames.
|
|
Not all adaptors support setting the RTS threshold.
|
|
.It Cm ssid Ar ssid
|
|
Set the desired Service Set Identifier (aka network name).
|
|
The SSID is a string up to 32 characters
|
|
in length and may be specified as either a normal string or in
|
|
hexadecimal when preceded by
|
|
.Ql 0x .
|
|
Additionally, the SSID may be cleared by setting it to
|
|
.Ql - .
|
|
.It Cm scan
|
|
Initiate a scan of neighboring stations, wait for it to complete, and
|
|
display all stations found.
|
|
Only the super-user can initiate a scan.
|
|
Depending on the capabilities of the APs, the following
|
|
flags can be included in the output:
|
|
.Bl -tag -width 3n
|
|
.It Li E
|
|
Extended Service Set (ESS).
|
|
Indicates that the station is part of an infrastructure network
|
|
(in contrast to an IBSS/ad-hoc network).
|
|
.It Li I
|
|
IBSS/ad-hoc network.
|
|
Indicates that the station is part of an ad-hoc network
|
|
(in contrast to an ESS network).
|
|
.It Li P
|
|
Privacy.
|
|
Data confidentiality is required for all data frames
|
|
exchanged within the BSS.
|
|
This means that this BSS requires the station to
|
|
use cryptographic means such as WEP, TKIP or AES-CCMP to
|
|
encrypt/decrypt data frames being exchanged with others.
|
|
.It Li S
|
|
Short Preamble.
|
|
Indicates that the network is using short preambles (defined
|
|
in 802.11b High Rate/DSSS PHY, short preamble utilizes a
|
|
56 bit sync field in contrast to a 128 bit field used in long
|
|
preamble mode).
|
|
.It Li s
|
|
Short slot time.
|
|
Indicates that the network is using a short slot time.
|
|
.El
|
|
.Pp
|
|
The
|
|
.Cm list scan
|
|
request can be used to show recent scan results without
|
|
initiating a new scan.
|
|
.It Cm stationname Ar name
|
|
Set the name of this station.
|
|
It appears that the station name is not really part of the IEEE 802.11
|
|
protocol though all interfaces seem to support it.
|
|
As such it only
|
|
seems to be meaningful to identical or virtually identical equipment.
|
|
Setting the station name is identical in syntax to setting the SSID.
|
|
.It Cm txpower Ar power
|
|
Set the power used to transmit frames.
|
|
The
|
|
.Ar power
|
|
argument
|
|
is a unitless value in the range 0 to 100 that is interpreted
|
|
by drivers to derive a device-specific value.
|
|
Out of range values are truncated.
|
|
Typically only a few discreet power settings are available and
|
|
the driver will use the setting closest to the specified value.
|
|
Not all adaptors support changing the transmit power.
|
|
.It Cm wepmode Ar mode
|
|
Set the desired WEP mode.
|
|
Not all adaptors support all modes.
|
|
The set of valid modes is
|
|
.Cm off , on ,
|
|
and
|
|
.Cm mixed .
|
|
The
|
|
.Cm mixed
|
|
mode explicitly tells the adaptor to allow association with access
|
|
points which allow both encrypted and unencrypted traffic.
|
|
On these adaptors,
|
|
.Cm on
|
|
means that the access point must only allow encrypted connections.
|
|
On other adaptors,
|
|
.Cm on
|
|
is generally another name for
|
|
.Cm mixed .
|
|
Modes are case insensitive.
|
|
.It Cm weptxkey Ar index
|
|
Set the WEP key to be used for transmission.
|
|
This is the same as setting the default transmission key with
|
|
.Cm deftxkey .
|
|
.It Cm wepkey Ar key Ns | Ns Ar index : Ns Ar key
|
|
Set the selected WEP key.
|
|
If an
|
|
.Ar index
|
|
is not given, key 1 is set.
|
|
A WEP key will be either 5 or 13
|
|
characters (40 or 104 bits) depending of the local network and the
|
|
capabilities of the adaptor.
|
|
It may be specified either as a plain
|
|
string or as a string of hexadecimal digits preceded by
|
|
.Ql 0x .
|
|
For maximum portability, hex keys are recommended;
|
|
the mapping of text keys to WEP encryption is usually driver-specific.
|
|
In particular, the
|
|
.Tn Windows
|
|
drivers do this mapping differently to
|
|
.Fx .
|
|
A key may be cleared by setting it to
|
|
.Ql - .
|
|
If WEP is supported then there are at least four keys.
|
|
Some adaptors support more than four keys.
|
|
If that is the case, then the first four keys
|
|
(1-4) will be the standard temporary keys and any others will be adaptor
|
|
specific keys such as permanent keys stored in NVRAM.
|
|
.It Cm wme
|
|
Enable Wireless Multimedia Extensions (WME) support, if available,
|
|
for the specified interface.
|
|
WME is a subset of the IEEE 802.11e standard to support the
|
|
efficient communication of realtime and multimedia data.
|
|
To disable WME support, use
|
|
.Fl wme .
|
|
.Pp
|
|
The following parameters are meaningful only when WME support is in use.
|
|
Parameters are specified per-AC (Access Category) and
|
|
split into those that are used by a station when acting
|
|
as an access point and those for client stations in the BSS.
|
|
The latter are received from the access point and may not be changed
|
|
(at the station).
|
|
The following Access Categories are recognized:
|
|
.Pp
|
|
.Bl -tag -width ".Cm AC_BK" -compact
|
|
.It Cm AC_BE
|
|
(or
|
|
.Cm BE )
|
|
best effort delivery,
|
|
.It Cm AC_BK
|
|
(or
|
|
.Cm BK )
|
|
background traffic,
|
|
.It Cm AC_VI
|
|
(or
|
|
.Cm VI )
|
|
video traffic,
|
|
.It Cm AC_VO
|
|
(or
|
|
.Cm VO )
|
|
voice traffic.
|
|
.El
|
|
.Pp
|
|
AC parameters are case-insensitive.
|
|
Traffic classification is done in the operating system using the
|
|
vlan priority associated with data frames or the
|
|
ToS (Type of Service) indication in IP-encapsulated frames.
|
|
If neither information is present, traffic is assigned to the
|
|
Best Effort (BE) category.
|
|
.Bl -tag -width indent
|
|
.It Cm ack Ar ac
|
|
Set the ACK policy for QoS transmissions by the local station;
|
|
this controls whether or not data frames transmitted by a station
|
|
require an ACK response from the receiving station.
|
|
To disable waiting for an ACK use
|
|
.Fl ack .
|
|
This parameter is applied only to the local station.
|
|
.It Cm acm Ar ac
|
|
Enable the Admission Control Mandatory (ACM) mechanism
|
|
for transmissions by the local station.
|
|
To disable the ACM use
|
|
.Fl acm .
|
|
On stations in a BSS this parameter is read-only and indicates
|
|
the setting received from the access point.
|
|
NB: ACM is not supported right now.
|
|
.It Cm aifs Ar ac Ar count
|
|
Set the Arbitration Inter Frame Spacing (AIFS)
|
|
channel access parameter to use for transmissions
|
|
by the local station.
|
|
On stations in a BSS this parameter is read-only and indicates
|
|
the setting received from the access point.
|
|
.It Cm cwmin Ar ac Ar count
|
|
Set the CWmin channel access parameter to use for transmissions
|
|
by the local station.
|
|
On stations in a BSS this parameter is read-only and indicates
|
|
the setting received from the access point.
|
|
.It Cm cwmax Ar ac Ar count
|
|
Set the CWmax channel access parameter to use for transmissions
|
|
by the local station.
|
|
On stations in a BSS this parameter is read-only and indicates
|
|
the setting received from the access point.
|
|
.It Cm txoplimit Ar ac Ar limit
|
|
Set the Transmission Opportunity Limit channel access parameter
|
|
to use for transmissions by the local station.
|
|
This parameter defines an interval of time when a WME station
|
|
has the right to initiate transmissions onto the wireless medium.
|
|
On stations in a BSS this parameter is read-only and indicates
|
|
the setting received from the access point.
|
|
.It Cm bss:aifs Ar ac Ar count
|
|
Set the AIFS channel access parameter to send to stations in a BSS.
|
|
This parameter is meaningful only when operating in ap mode.
|
|
.It Cm bss:cwmin Ar ac Ar count
|
|
Set the CWmin channel access parameter to send to stations in a BSS.
|
|
This parameter is meaningful only when operating in ap mode.
|
|
.It Cm bss:cwmax Ar ac Ar count
|
|
Set the CWmax channel access parameter to send to stations in a BSS.
|
|
This parameter is meaningful only when operating in ap mode.
|
|
.It Cm bss:txoplimit Ar ac Ar limit
|
|
Set the TxOpLimit channel access parameter to send to stations in a BSS.
|
|
This parameter is meaningful only when operating in ap mode.
|
|
.El
|
|
.El
|
|
.Pp
|
|
The following parameters support an optional access control list
|
|
feature available with some adaptors when operating in ap mode; see
|
|
.Xr wlan_acl 4 .
|
|
This facility allows an access point to accept/deny association
|
|
requests based on the MAC address of the station.
|
|
Note that this feature does not significantly enhance security
|
|
as MAC address spoofing is easy to do.
|
|
.Bl -tag -width indent
|
|
.It Cm mac:add Ar address
|
|
Add the specified MAC address to the database.
|
|
Depending on the policy setting association requests from the
|
|
specified station will be allowed or denied.
|
|
.It Cm mac:allow
|
|
Set the ACL policy to permit association only by
|
|
stations registered in the database.
|
|
.It Cm mac:del Ar address
|
|
Delete the specified MAC address from the database.
|
|
.It Cm mac:deny
|
|
Set the ACL policy to deny association only by
|
|
stations registered in the database.
|
|
.It Cm mac:kick Ar address
|
|
Force the specified station to be deauthenticated.
|
|
This typically is done to block a station after updating the
|
|
address database.
|
|
.It Cm mac:open
|
|
Set the ACL policy to allow all stations to associate.
|
|
.It Cm mac:flush
|
|
Delete all entries in the database.
|
|
.El
|
|
.Pp
|
|
The following parameters are for compatibility with other systems:
|
|
.Bl -tag -width indent
|
|
.It Cm nwid Ar ssid
|
|
Another name for the
|
|
.Cm ssid
|
|
parameter.
|
|
Included for
|
|
.Nx
|
|
compatibility.
|
|
.It Cm station Ar name
|
|
Another name for the
|
|
.Cm stationname
|
|
parameter.
|
|
Included for
|
|
.Bsx
|
|
compatibility.
|
|
.It Cm wep
|
|
Another way of saying
|
|
.Cm wepmode on .
|
|
Included for
|
|
.Bsx
|
|
compatibility.
|
|
.It Fl wep
|
|
Another way of saying
|
|
.Cm wepmode off .
|
|
Included for
|
|
.Bsx
|
|
compatibility.
|
|
.It Cm nwkey key
|
|
Another way of saying:
|
|
.Dq Li "wepmode on weptxkey 1 wepkey 1:key wepkey 2:- wepkey 3:- wepkey 4:-" .
|
|
Included for
|
|
.Nx
|
|
compatibility.
|
|
.It Cm nwkey Xo
|
|
.Sm off
|
|
.Ar n : k1 , k2 , k3 , k4
|
|
.Sm on
|
|
.Xc
|
|
Another way of saying
|
|
.Dq Li "wepmode on weptxkey n wepkey 1:k1 wepkey 2:k2 wepkey 3:k3 wepkey 4:k4" .
|
|
Included for
|
|
.Nx
|
|
compatibility.
|
|
.It Fl nwkey
|
|
Another way of saying
|
|
.Cm wepmode off .
|
|
Included for
|
|
.Nx
|
|
compatibility.
|
|
.El
|
|
.Pp
|
|
The following parameters are specific to bridge interfaces:
|
|
.Bl -tag -width indent
|
|
.It Cm addm Ar interface
|
|
Add the interface named by
|
|
.Ar interface
|
|
as a member of the bridge.
|
|
The interface is put into promiscuous mode
|
|
so that it can receive every packet sent on the network.
|
|
.It Cm deletem Ar interface
|
|
Remove the interface named by
|
|
.Ar interface
|
|
from the bridge.
|
|
Promiscuous mode is disabled on the interface when
|
|
it is removed from the bridge.
|
|
.It Cm maxaddr Ar size
|
|
Set the size of the bridge address cache to
|
|
.Ar size .
|
|
The default is 100 entries.
|
|
.It Cm timeout Ar seconds
|
|
Set the timeout of address cache entries to
|
|
.Ar seconds
|
|
seconds.
|
|
If
|
|
.Ar seconds
|
|
is zero, then address cache entries will not be expired.
|
|
The default is 240 seconds.
|
|
.It Cm addr
|
|
Display the addresses that have been learned by the bridge.
|
|
.It Cm static Ar interface-name Ar address
|
|
Add a static entry into the address cache pointing to
|
|
.Ar interface-name .
|
|
Static entries are never aged out of the cache or re-placed, even if the
|
|
address is seen on a different interface.
|
|
.It Cm deladdr Ar address
|
|
Delete
|
|
.Ar address
|
|
from the address cache.
|
|
.It Cm flush
|
|
Delete all dynamically-learned addresses from the address cache.
|
|
.It Cm flushall
|
|
Delete all addresses, including static addresses, from the address cache.
|
|
.It Cm discover Ar interface
|
|
Mark an interface as a
|
|
.Dq discovering
|
|
interface.
|
|
When the bridge has no address cache entry
|
|
(either dynamic or static)
|
|
for the destination address of a packet,
|
|
the bridge will forward the packet to all
|
|
member interfaces marked as
|
|
.Dq discovering .
|
|
This is the default for all interfaces added to a bridge.
|
|
.It Cm -discover Ar interface
|
|
Clear the
|
|
.Dq discovering
|
|
attribute on a member interface.
|
|
For packets without the
|
|
.Dq discovering
|
|
attribute, the only packets forwarded on the interface are broadcast
|
|
or multicast packets and packets for which the destination address
|
|
is known to be on the interface's segment.
|
|
.It Cm learn Ar interface
|
|
Mark an interface as a
|
|
.Dq learning
|
|
interface.
|
|
When a packet arrives on such an interface, the source
|
|
address of the packet is entered into the address cache as being a
|
|
destination address on the interface's segment.
|
|
This is the default for all interfaces added to a bridge.
|
|
.It Cm -learn Ar interface
|
|
Clear the
|
|
.Dq learning
|
|
attribute on a member interface.
|
|
.It Cm span Ar interface
|
|
Add the interface named by
|
|
.Ar interface
|
|
as a span port on the bridge.
|
|
Span ports transmit a copy of every frame received by the bridge.
|
|
This is most useful for snooping a bridged network passively on
|
|
another host connected to one of the span ports of the bridge.
|
|
.It Cm -span Ar interface
|
|
Delete the interface named by
|
|
.Ar interface
|
|
from the list of span ports of the bridge.
|
|
.It Cm stp Ar interface
|
|
Enable Spanning Tree protocol on
|
|
.Ar interface .
|
|
The
|
|
.Xr if_bridge 4
|
|
driver has support for the IEEE 802.1D Spanning Tree protocol (STP).
|
|
Spanning Tree is used to detect and remove loops in a network topology.
|
|
.It Cm -stp Ar interface
|
|
Disable Spanning Tree protocol on
|
|
.Ar interface .
|
|
This is the default for all interfaces added to a bridge.
|
|
.It Cm maxage Ar seconds
|
|
Set the time that a Spanning Tree protocol configuration is valid.
|
|
The default is 20 seconds.
|
|
The minimum is 1 second and the maximum is 255 seconds.
|
|
.It Cm fwddelay Ar seconds
|
|
Set the time that must pass before an interface begins forwarding
|
|
packets when Spanning Tree is enabled.
|
|
The default is 15 seconds.
|
|
The minimum is 1 second and the maximum is 255 seconds.
|
|
.It Cm hellotime Ar seconds
|
|
Set the time between broadcasting of Spanning Tree protocol
|
|
configuration messages.
|
|
The default is 2 seconds.
|
|
The minimum is 1 second and the maximum is 255 seconds.
|
|
.It Cm priority Ar value
|
|
Set the bridge priority for Spanning Tree.
|
|
The default is 32768.
|
|
The minimum is 0 and the maximum is 65536.
|
|
.It Cm ifpriority Ar interface Ar value
|
|
Set the Spanning Tree priority of
|
|
.Ar interface
|
|
to
|
|
.Ar value .
|
|
The default is 128.
|
|
The minimum is 0 and the maximum is 255.
|
|
.It Cm ifpathcost Ar interface Ar value
|
|
Set the Spanning Tree path cost of
|
|
.Ar interface
|
|
to
|
|
.Ar value .
|
|
The default is 55.
|
|
The minimum is 0 and the maximum is 65535.
|
|
.El
|
|
.Pp
|
|
The following parameters are specific to IP tunnel interfaces,
|
|
.Xr gif 4 :
|
|
.Bl -tag -width indent
|
|
.It Cm tunnel Ar src_addr dest_addr
|
|
Configure the physical source and destination address for IP tunnel
|
|
interfaces.
|
|
The arguments
|
|
.Ar src_addr
|
|
and
|
|
.Ar dest_addr
|
|
are interpreted as the outer source/destination for the encapsulating
|
|
IPv4/IPv6 header.
|
|
.It Fl tunnel
|
|
Unconfigure the physical source and destination address for IP tunnel
|
|
interfaces previously configured with
|
|
.Cm tunnel .
|
|
.It Cm deletetunnel
|
|
Another name for the
|
|
.Fl tunnel
|
|
parameter.
|
|
.El
|
|
.Pp
|
|
The following parameters are specific to
|
|
.Xr pfsync 4
|
|
interfaces:
|
|
.Bl -tag -width indent
|
|
.It Cm maxupd Ar n
|
|
Set the maximum number of updates for a single state which
|
|
can be collapsed into one.
|
|
This is an 8-bit number; the default value is 128.
|
|
.El
|
|
.Pp
|
|
The following parameters are specific to
|
|
.Xr vlan 4
|
|
interfaces:
|
|
.Bl -tag -width indent
|
|
.It Cm vlan Ar vlan_tag
|
|
Set the VLAN tag value to
|
|
.Ar vlan_tag .
|
|
This value is a 16-bit number which is used to create an 802.1Q
|
|
VLAN header for packets sent from the
|
|
.Xr vlan 4
|
|
interface.
|
|
Note that
|
|
.Cm vlan
|
|
and
|
|
.Cm vlandev
|
|
must both be set at the same time.
|
|
.It Cm vlandev Ar iface
|
|
Associate the physical interface
|
|
.Ar iface
|
|
with a
|
|
.Xr vlan 4
|
|
interface.
|
|
Packets transmitted through the
|
|
.Xr vlan 4
|
|
interface will be
|
|
diverted to the specified physical interface
|
|
.Ar iface
|
|
with 802.1Q VLAN encapsulation.
|
|
Packets with 802.1Q encapsulation received
|
|
by the parent interface with the correct VLAN tag will be diverted to
|
|
the associated
|
|
.Xr vlan 4
|
|
pseudo-interface.
|
|
The
|
|
.Xr vlan 4
|
|
interface is assigned a
|
|
copy of the parent interface's flags and the parent's ethernet address.
|
|
The
|
|
.Cm vlandev
|
|
and
|
|
.Cm vlan
|
|
must both be set at the same time.
|
|
If the
|
|
.Xr vlan 4
|
|
interface already has
|
|
a physical interface associated with it, this command will fail.
|
|
To
|
|
change the association to another physical interface, the existing
|
|
association must be cleared first.
|
|
.Pp
|
|
Note: if the hardware tagging capability
|
|
is set on the parent interface, the
|
|
.Xr vlan 4
|
|
pseudo
|
|
interface's behavior changes:
|
|
the
|
|
.Xr vlan 4
|
|
interface recognizes that the
|
|
parent interface supports insertion and extraction of VLAN tags on its
|
|
own (usually in firmware) and that it should pass packets to and from
|
|
the parent unaltered.
|
|
.It Fl vlandev Op Ar iface
|
|
If the driver is a
|
|
.Xr vlan 4
|
|
pseudo device, disassociate the parent interface from it.
|
|
This breaks the link between the
|
|
.Xr vlan 4
|
|
interface and its parent,
|
|
clears its VLAN tag, flags and its link address and shuts the interface down.
|
|
The
|
|
.Ar iface
|
|
argument is useless and hence deprecated.
|
|
.El
|
|
.Pp
|
|
The following parameters are specific to
|
|
.Xr carp 4
|
|
interfaces:
|
|
.Bl -tag -width indent
|
|
.It Cm advbase Ar seconds
|
|
Specifies the base of the advertisement interval in seconds.
|
|
The acceptable values are 1 to 255.
|
|
The default value is 1.
|
|
.\" The default value is
|
|
.\" .Dv CARP_DFLTINTV .
|
|
.It Cm advskew Ar interval
|
|
Specifies the skew to add to the base advertisement interval to
|
|
make one host advertise slower than another host.
|
|
It is specified in 1/256 of seconds.
|
|
The acceptable values are 1 to 254.
|
|
The default value is 0.
|
|
.It Cm pass Ar phrase
|
|
Set the authentication key to
|
|
.Ar phrase .
|
|
.It Cm vhid Ar n
|
|
Set the virtual host ID.
|
|
This is a required setting.
|
|
Acceptable values are 1 to 255.
|
|
.El
|
|
.Pp
|
|
The
|
|
.Nm
|
|
utility displays the current configuration for a network interface
|
|
when no optional parameters are supplied.
|
|
If a protocol family is specified,
|
|
.Nm
|
|
will report only the details specific to that protocol family.
|
|
.Pp
|
|
If the
|
|
.Fl m
|
|
flag is passed before an interface name,
|
|
.Nm
|
|
will display the capability list and all
|
|
of the supported media for the specified interface.
|
|
If
|
|
.Fl L
|
|
flag is supplied, address lifetime is displayed for IPv6 addresses,
|
|
as time offset string.
|
|
.Pp
|
|
Optionally, the
|
|
.Fl a
|
|
flag may be used instead of an interface name.
|
|
This flag instructs
|
|
.Nm
|
|
to display information about all interfaces in the system.
|
|
The
|
|
.Fl d
|
|
flag limits this to interfaces that are down, and
|
|
.Fl u
|
|
limits this to interfaces that are up.
|
|
When no arguments are given,
|
|
.Fl a
|
|
is implied.
|
|
.Pp
|
|
The
|
|
.Fl l
|
|
flag may be used to list all available interfaces on the system, with
|
|
no other additional information.
|
|
Use of this flag is mutually exclusive
|
|
with all other flags and commands, except for
|
|
.Fl d
|
|
(only list interfaces that are down)
|
|
and
|
|
.Fl u
|
|
(only list interfaces that are up).
|
|
.Pp
|
|
The
|
|
.Fl v
|
|
flag may be used to get more verbose status for an interface.
|
|
.Pp
|
|
The
|
|
.Fl C
|
|
flag may be used to list all of the interface cloners available on
|
|
the system, with no additional information.
|
|
Use of this flag is mutually exclusive with all other flags and commands.
|
|
.Pp
|
|
The
|
|
.Fl k
|
|
flag causes keying information for the interface, if available, to be
|
|
printed.
|
|
For example, the values of 802.11 WEP keys will be printed, if accessible to
|
|
the current user.
|
|
This information is not printed by default, as it may be considered
|
|
sensitive.
|
|
.Pp
|
|
Only the super-user may modify the configuration of a network interface.
|
|
.Sh NOTES
|
|
The media selection system is relatively new and only some drivers support
|
|
it (or have need for it).
|
|
.Sh DIAGNOSTICS
|
|
Messages indicating the specified interface does not exist, the
|
|
requested address is unknown, or the user is not privileged and
|
|
tried to alter an interface's configuration.
|
|
.Sh SEE ALSO
|
|
.Xr netstat 1 ,
|
|
.Xr carp 4 ,
|
|
.Xr netintro 4 ,
|
|
.Xr pfsync 4 ,
|
|
.Xr polling 4 ,
|
|
.Xr vlan 4 ,
|
|
.\" .Xr eon 5 ,
|
|
.Xr rc 8 ,
|
|
.Xr routed 8 ,
|
|
.Xr sysctl 8
|
|
.Sh HISTORY
|
|
The
|
|
.Nm
|
|
utility appeared in
|
|
.Bx 4.2 .
|
|
.Sh BUGS
|
|
Basic IPv6 node operation requires a link-local address on each
|
|
interface configured for IPv6.
|
|
Normally, such an address is automatically configured by the
|
|
kernel on each interface added to the system; this behaviour may
|
|
be disabled by setting the sysctl MIB variable
|
|
.Va net.inet6.ip6.auto_linklocal
|
|
to 0.
|
|
.Pp
|
|
If you delete such an address using
|
|
.Nm ,
|
|
the kernel may act very oddly.
|
|
Do this at your own risk.
|