cd7dffd058
and if queue mechanism; also fix up (non-11n) TX fragment handling. This may result in a bit of a performance drop for now but I plan on debugging and resolving this at a later stage. Whilst here, fix the transmit path so fragment transmission works. The TX fragmentation handling is a bit more special. In order to correctly transmit TX fragments, there's a bunch of corner cases that need to be handled: * They must be transmitted back to back, in the same order.. * .. ie, you need to hold the TX lock whilst transmitting this set of fragments rather than interleaving it with other MSDUs destined to other nodes; * The length of the next fragment is required when transmitting, in order to correctly set the NAV field in the current frame to the length of the next frame; which requires .. * .. that we know the transmit duration of the next frame, which .. * .. requires us to set the rate of all fragments to the same length, or make the decision up-front, etc. To facilitate this, I've added a new ath_buf field to describe the length of the next fragment. This avoids having to keep the mbuf chain together. This used to work before my 11n TX path work because the ath_tx_start() routine would be handed a single mbuf with m_nextpkt pointing to the next frame, and that would be maintained all the way up to when the duration calculation was done. This doesn't hold true any longer - the actual queuing may occur at any point in the future (think ath_node TID software queuing) so this information needs to be maintained. Right now this does work for non-11n frames but it doesn't at all enforce the same rate control decision for all frames in the fragment. I plan on fixing this in a followup commit. RTS/CTS has the same issue, I'll look at fixing this in a subsequent commit. Finaly, 11n fragment support requires the driver to have fully decided what the rate scenario setup is - including 20/40MHz, short/long GI, STBC, LDPC, number of streams, etc. Right now that decision is (currently) made _after_ the NAV field value is updated. I'll fix all of this in subsequent commits. Tested: * AR5416, STA, transmitting 11abg fragments * AR5416, STA, 11n fragments work but the NAV field is incorrect for the reasons above. TODO: * It would be nice to be able to queue mbufs per-node and per-TID so we can only queue ath_buf entries when it's time to assemble frames to send to the hardware. But honestly, we should just do that level of software queue management in net80211 rather than ath(4), so I'm going to leave this alone for now. * More thorough AP, mesh and adhoc testing. * Ensure that net80211 doesn't hand us fragmented frames when A-MPDU has been negotiated, as we can't do software retransmission of fragments. * .. set CLRDMASK when transmitting fragments, just to ensure.
This is the top level of the FreeBSD source directory. This file was last revised on: $FreeBSD$ For copyright information, please see the file COPYRIGHT in this directory (additional copyright information also exists for some sources in this tree - please see the specific source directories for more information). The Makefile in this directory supports a number of targets for building components (or all) of the FreeBSD source tree, the most commonly used one being ``world'', which rebuilds and installs everything in the FreeBSD system from the source tree except the kernel, the kernel-modules and the contents of /etc. The ``world'' target should only be used in cases where the source tree has not changed from the currently running version. See: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/makeworld.html for more information, including setting make(1) variables. The ``buildkernel'' and ``installkernel'' targets build and install the kernel and the modules (see below). Please see the top of the Makefile in this directory for more information on the standard build targets and compile-time flags. Building a kernel is a somewhat more involved process, documentation for which can be found at: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig.html And in the config(8) man page. Note: If you want to build and install the kernel with the ``buildkernel'' and ``installkernel'' targets, you might need to build world before. More information is available in the handbook. The sample kernel configuration files reside in the sys/<arch>/conf sub-directory (assuming that you've installed the kernel sources), the file named GENERIC being the one used to build your initial installation kernel. The file NOTES contains entries and documentation for all possible devices, not just those commonly used. It is the successor of the ancient LINT file, but in contrast to LINT, it is not buildable as a kernel but a pure reference and documentation file. Source Roadmap: --------------- bin System/user commands. cddl Various commands and libraries under the Common Development and Distribution License. contrib Packages contributed by 3rd parties. crypto Cryptography stuff (see crypto/README). etc Template files for /etc. games Amusements. gnu Various commands and libraries under the GNU Public License. Please see gnu/COPYING* for more information. include System include files. kerberos5 Kerberos5 (Heimdal) package. lib System libraries. libexec System daemons. release Release building Makefile & associated tools. rescue Build system for statically linked /rescue utilities. sbin System commands. secure Cryptographic libraries and commands. share Shared resources. sys Kernel sources. tools Utilities for regression testing and miscellaneous tasks. usr.bin User commands. usr.sbin System administration commands. For information on synchronizing your source tree with one or more of the FreeBSD Project's development branches, please see: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/synching.html