freebsd-skq/sys/i386/conf
wpaul ce0ede96f1 Take the support for the 8139C+/8169/8169S/8110S chips out of the
rl(4) driver and put it in a new re(4) driver. The re(4) driver shares
the if_rlreg.h file with rl(4) but is a separate module. (Ultimately
I may change this. For now, it's convenient.)

rl(4) has been modified so that it will never attach to an 8139C+
chip, leaving it to re(4) instead. Only re(4) has the PCI IDs to
match the 8169/8169S/8110S gigE chips. if_re.c contains the same
basic code that was originally bolted onto if_rl.c, with the
following updates:

- Added support for jumbo frames. Currently, there seems to be
  a limit of approximately 6200 bytes for jumbo frames on transmit.
  (This was determined via experimentation.) The 8169S/8110S chips
  apparently are limited to 7.5K frames on transmit. This may require
  some more work, though the framework to handle jumbo frames on RX
  is in place: the re_rxeof() routine will gather up frames than span
  multiple 2K clusters into a single mbuf list.

- Fixed bug in re_txeof(): if we reap some of the TX buffers,
  but there are still some pending, re-arm the timer before exiting
  re_txeof() so that another timeout interrupt will be generated, just
  in case re_start() doesn't do it for us.

- Handle the 'link state changed' interrupt

- Fix a detach bug. If re(4) is loaded as a module, and you do
  tcpdump -i re0, then you do 'kldunload if_re,' the system will
  panic after a few seconds. This happens because ether_ifdetach()
  ends up calling the BPF detach code, which notices the interface
  is in promiscuous mode and tries to switch promisc mode off while
  detaching the BPF listner. This ultimately results in a call
  to re_ioctl() (due to SIOCSIFFLAGS), which in turn calls re_init()
  to handle the IFF_PROMISC flag change. Unfortunately, calling re_init()
  here turns the chip back on and restarts the 1-second timeout loop
  that drives re_tick(). By the time the timeout fires, if_re.ko
  has been unloaded, which results in a call to invalid code and
  blows up the system.

  To fix this, I cleared the IFF_UP flag before calling ether_ifdetach(),
  which stops the ioctl routine from trying to reset the chip.

- Modified comments in re_rxeof() relating to the difference in
  RX descriptor status bit layout between the 8139C+ and the gigE
  chips. The layout is different because the frame length field
  was expanded from 12 bits to 13, and they got rid of one of the
  status bits to make room.

- Add diagnostic code (re_diag()) to test for the case where a user
  has installed a broken 32-bit 8169 PCI NIC in a 64-bit slot. Some
  NICs have the REQ64# and ACK64# lines connected even though the
  board is 32-bit only (in this case, they should be pulled high).
  This fools the chip into doing 64-bit DMA transfers even though
  there is no 64-bit data path. To detect this, re_diag() puts the
  chip into digital loopback mode and sets the receiver to promiscuous
  mode, then initiates a single 64-byte packet transmission. The
  frame is echoed back to the host, and if the frame contents are
  intact, we know DMA is working correctly, otherwise we complain
  loudly on the console and abort the device attach. (At the moment,
  I don't know of any way to work around the problem other than
  physically modifying the board, so until/unless I can think of a
  software workaround, this will have do to.)

- Created re(4) man page

- Modified rlphy.c to allow re(4) to attach as well as rl(4).

Note that this code works for the sample 8169/Marvell 88E1000 NIC
that I have, but probably won't work for the 8169S/8110S chips.
RealTek has sent me some sample NICs, but they haven't arrived yet.
I will probably need to add an rlgphy driver to handle the on-board
PHY in the 8169S/8110S (it needs special DSP initialization).
2003-09-08 02:11:25 +00:00
..
GENERIC Take the support for the 8139C+/8169/8169S/8110S chips out of the 2003-09-08 02:11:25 +00:00
GENERIC.hints
gethints.awk
Makefile Implemented "nooption" and "nomakeoption" config(8) tokens. 2003-02-26 23:36:59 +00:00
NOTES As warned: Initiate deorbit burn for the pcaudio driver. 2003-08-15 14:56:05 +00:00
OLDCARD
PAE Fix the busdma support in twe to support EINPROGRESS and enable it for 2003-08-12 06:38:55 +00:00
SMP Nuke options HTT infavor of machdep.hlt_logical_cpus tunable/sysctl. 2003-03-26 19:49:34 +00:00