a0e860ef19
I/O8+ and I/O4+ intelligent serial controllers. si is for completely different hardware, also made by Specialix.
160 lines
4.5 KiB
C
160 lines
4.5 KiB
C
/*
|
|
* Device driver for Specialix I/O8+ multiport serial card.
|
|
*
|
|
* Copyright 2003 Frank Mayhar <frank@exit.com>
|
|
*
|
|
* Derived from the "si" driver by Peter Wemm <peter@netplex.com.au>, using
|
|
* lots of information from the Linux "specialix" driver by Roger Wolff
|
|
* <R.E.Wolff@BitWizard.nl> and from the Intel CD1865 "Intelligent Eight-
|
|
* Channel Communications Controller" datasheet. Roger was also nice
|
|
* enough to answer numerous questions about stuff specific to the I/O8+
|
|
* not covered by the CD1865 datasheet.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notices, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notices, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY ``AS IS'' AND ANY EXPRESS OR IMPLIED
|
|
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
|
|
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
|
|
* NO EVENT SHALL THE AUTHORS BE LIABLE.
|
|
*
|
|
* $FreeBSD$
|
|
*/
|
|
|
|
|
|
/* Utility functions and macros for the Specialix I/O8+ driver. */
|
|
|
|
/*
|
|
* sx_cd1865_out()
|
|
* Write a CD1865 register on the card.
|
|
*/
|
|
static __inline void
|
|
sx_cd1865_out(
|
|
struct sx_softc *sc,
|
|
unsigned int reg,
|
|
unsigned char val)
|
|
{
|
|
bus_space_write_1(sc->sc_st, sc->sc_sh, SX_ADDR_REG, reg);
|
|
bus_space_write_1(sc->sc_st, sc->sc_sh, SX_DATA_REG, val);
|
|
}
|
|
|
|
/*
|
|
* sx_cd1865_in()
|
|
* Read a register from the card.
|
|
*/
|
|
static __inline unsigned char
|
|
sx_cd1865_in(
|
|
struct sx_softc *sc,
|
|
unsigned int reg)
|
|
{
|
|
bus_space_write_1(sc->sc_st, sc->sc_sh, SX_ADDR_REG, reg);
|
|
return(bus_space_read_1(sc->sc_st, sc->sc_sh, SX_DATA_REG));
|
|
}
|
|
|
|
/*
|
|
* sx_cd1865_bis()
|
|
* Set bits in a CD1865 register.
|
|
*/
|
|
static __inline void
|
|
sx_cd1865_bis(
|
|
struct sx_softc *sc,
|
|
unsigned int reg,
|
|
unsigned char bits)
|
|
{
|
|
register unsigned char rval;
|
|
|
|
rval = sx_cd1865_in(sc, reg);
|
|
rval |= bits;
|
|
sx_cd1865_out(sc, reg, rval);
|
|
}
|
|
|
|
/*
|
|
* sx_cd1865_bic()
|
|
* Clear bits in a CD1865 register.
|
|
*/
|
|
static __inline void
|
|
sx_cd1865_bic(
|
|
struct sx_softc *sc,
|
|
unsigned int reg,
|
|
unsigned char bits)
|
|
{
|
|
register unsigned char rval;
|
|
|
|
rval = sx_cd1865_in(sc, reg);
|
|
rval &= ~bits;
|
|
sx_cd1865_out(sc, reg, rval);
|
|
}
|
|
|
|
/*
|
|
* sx_cd1865_wait_CCR()
|
|
* Spin waiting for the board Channel Command Register to clear.
|
|
*
|
|
* Description:
|
|
* The CD1865 processor clears the Channel Command Register to
|
|
* indicate that it has completed the last command. This routine
|
|
* waits for the CCR to become zero by watching the register,
|
|
* delaying ten microseconds between each check. We time out after
|
|
* ten milliseconds (or SX_CCR_TIMEOUT microseconds).
|
|
*/
|
|
static __inline void
|
|
sx_cd1865_wait_CCR(
|
|
struct sx_softc *sc,
|
|
unsigned int ei_flag)
|
|
{
|
|
unsigned int to = SX_CCR_TIMEOUT/10;
|
|
|
|
while (to-- > 0) {
|
|
if (sx_cd1865_in(sc, CD1865_CCR|ei_flag) == 0)
|
|
return;
|
|
DELAY(10);
|
|
}
|
|
printf("sx: Timeout waiting for CCR to clear.\n");
|
|
}
|
|
|
|
/*
|
|
* sx_cd1865_etcmode()
|
|
* Set or clear embedded transmit command mode on a CD1865 port.
|
|
*
|
|
* Description:
|
|
* We can use commands embedded in the transmit data stream to do
|
|
* things like start and stop breaks or insert time delays. We normally
|
|
* run with embedded commands disabled; this routine selects the channel
|
|
* we're dealing with and enables or disables embedded commands depending
|
|
* on the flag passed to it. The caller must remember this state and
|
|
* escape any NULs it sends while embedded commands are enabled.
|
|
* Should be called at spltty(). Disables interrupts for the duration
|
|
* of the routine.
|
|
*/
|
|
static __inline void
|
|
sx_cd1865_etcmode(
|
|
struct sx_softc *sc,
|
|
unsigned int ei_flag,
|
|
int chan,
|
|
int mode)
|
|
{
|
|
sx_cd1865_out(sc, CD1865_CAR|ei_flag, chan); /* Select channel. */
|
|
if (mode) { /* Enable embedded commands? */
|
|
sx_cd1865_bis(sc, CD1865_COR2|ei_flag, CD1865_COR2_ETC);
|
|
}
|
|
else {
|
|
sx_cd1865_bic(sc, CD1865_COR2|ei_flag, CD1865_COR2_ETC);
|
|
}
|
|
/*
|
|
* Wait for the CCR to clear, ding the card, let it know stuff
|
|
* changed, then wait for CCR to clear again.
|
|
*/
|
|
sx_cd1865_wait_CCR(sc, ei_flag);
|
|
sx_cd1865_out(sc, CD1865_CCR|ei_flag, CD1865_CCR_CORCHG2);
|
|
sx_cd1865_wait_CCR(sc, ei_flag);
|
|
}
|
|
|
|
int sx_probe_io8(device_t dev);
|
|
int sx_init_cd1865(struct sx_softc *sc, int unit);
|
|
struct sx_port *sx_int_port(struct sx_softc *sc, int unit);
|