dd991bd5a1
These firmwares were obtained from the beta "Chelsio T5/T4 Unified Wire v2.12.0.2 for Linux" release. Changes since last release are listed in the "Release Notes" accompanying the beta release and are copy-pasted here as well. The plan is to have only GA'd firmwares in any -STABLE FreeBSD branch so I'll MFC this (after 2 months) only if it ends up in a GA release. ================================================================================ ================================================================================ 22.1. T5 Firmware +++++++++++++++++++++++++++++++++ Version : 1.15.28.0 Date : 02/29/2016 ================================================================================ FIXES ----- BASE: - Fixed an issue in FW_RSS_VI_CONFIG_CMD handling where the default ingress queue was ignored. - Fixed an issue where adapter failed to load fw by adjusting DRAM frequency. - Fixed an issue in watchdog which was causing VM bring-up failure after reboot. - Fixed 40G link failures with some switches when auto-negotiation enabled. - Fixed to improve on link bring-up time. - Per port buffer groups size doubled to improve performance. - Fixed an issue where bogus d3hot bits were set causing traffic stall. - Fixed an issue where sometimes adapter was not seen after reboot. - Fixed an issue where iWARP was crashing in conjunction with traffic management. - Fixed an issue where link failed to come up after removing twinax cable and inserting optical module. OFLD - Fixed a potential iSCSI data corruption issue by disabling RxFragEn flag. FOiSCSI - Fixed an issue in recovery path where connection was getting closed before recovery processing was done. - Fixed an issue in TCP port reuse. - Fixed an issue in recovery path when large number (>64) of iSCSI connections were in use. - Returned ENETUNREACH if IP was not been provisioned yet and driver tried to use given inerface. ENHANCEMENTS ------------ BASE: - Added new interface to program DCA settings in SGE contexts; allow 32-byte IQE size - Added PTP interface fw_ptp_ts to support PTP Frequeny and Offset adjustment. - Added MPS raw interface. ETH: - New mailbox command FW_DCB_IEEE_CMD api added for IEEE dcbx. OFLD: - WR opcode is returned to host in cqe error response. ================================================================================ ================================================================================ 22.2. T4 Firmware +++++++++++++++++ Version : 1.15.28.0 Date : 02/29/2016 ================================================================================ FIXES ----- BASE: - Fixed an issue in FW_RSS_VI_CONFIG_CMD handling where default ingress queue was ignored. - Fixed an issue in watchdog which was causing VM bring-up failure after reboot. - Per port buffer groups size doubled to improve performance. - Fixed an issue where iWARP was crashing in conjunction with traffic management. FOiSCSI: - Fixed an issue in recovery path where connection was getting closed before recovery processing was done. - Fixed an issue in TCP port reuse. - Fixed an issue in recovery path when large number (>64) of iSCSI connections were in use. - Returned ENETUNREACH if IP had not been provisioned yet and driver tried to use given inerface. ENHANCEMENTS ------------ BASE: - Added MPS raw interface. ETH: - New mailbox command FW_DCB_IEEE_CMD api added for IEEE dcbx. ================================================================================ Obtained from: Chelsio Communications MFC after: 2 months Sponsored by: Chelsio Communications
This is the top level of the FreeBSD source directory. This file was last revised on: $FreeBSD$ For copyright information, please see the file COPYRIGHT in this directory (additional copyright information also exists for some sources in this tree - please see the specific source directories for more information). The Makefile in this directory supports a number of targets for building components (or all) of the FreeBSD source tree. See build(7) and http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/makeworld.html for more information, including setting make(1) variables. The `buildkernel` and `installkernel` targets build and install the kernel and the modules (see below). Please see the top of the Makefile in this directory for more information on the standard build targets and compile-time flags. Building a kernel is a somewhat more involved process. See build(7), config(8), and http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig.html for more information. Note: If you want to build and install the kernel with the `buildkernel` and `installkernel` targets, you might need to build world before. More information is available in the handbook. The kernel configuration files reside in the sys/<arch>/conf sub-directory. GENERIC is the default configuration used in release builds. NOTES contains entries and documentation for all possible devices, not just those commonly used. Source Roadmap: --------------- bin System/user commands. cddl Various commands and libraries under the Common Development and Distribution License. contrib Packages contributed by 3rd parties. crypto Cryptography stuff (see crypto/README). etc Template files for /etc. games Amusements. gnu Various commands and libraries under the GNU Public License. Please see gnu/COPYING* for more information. include System include files. kerberos5 Kerberos5 (Heimdal) package. lib System libraries. libexec System daemons. release Release building Makefile & associated tools. rescue Build system for statically linked /rescue utilities. sbin System commands. secure Cryptographic libraries and commands. share Shared resources. sys Kernel sources. tests Regression tests which can be run by Kyua. See tests/README for additional information. tools Utilities for regression testing and miscellaneous tasks. usr.bin User commands. usr.sbin System administration commands. For information on synchronizing your source tree with one or more of the FreeBSD Project's development branches, please see: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/synching.html