ad01e0c856
This driver supports PCI Xr-based and ISA Xem Digiboard cards. dgm will go away soon if there are no problems reported. For now, configuring dgm into your kernel warns that you should be using digi. This driver is probably close to supporting Xi, Xe and Xeve cards, but I wouldn't expect them to work properly (hardware donations welcome). The digi_* pseudo-drivers are not drivers themselves but contain the BIOS and FEP/OS binaries for various digiboard cards and are auto-loaded and auto-unloaded by the digi driver at initialisation time. They *may* be configured into the kernel, but waste a lot of space if they are. They're intended to be left as modules. The digictl program is (mainly) used to re-initialise cards that have external port modules attached such as the PC/Xem.
81 lines
2.0 KiB
Groff
81 lines
2.0 KiB
Groff
.\" $FreeBSD$
|
|
.Dd May 1, 2001
|
|
.Dt DIGICTL 8
|
|
.Os
|
|
.Sh NAME
|
|
.Nm digictl
|
|
.Nd Control Digiboard devices
|
|
.Sh SYNOPSIS
|
|
.Nm
|
|
.Op Fl d Ar debug
|
|
.Op Fl ir
|
|
.Ar device ...
|
|
.Sh DESCRIPTION
|
|
The
|
|
.Nm
|
|
program provides control of the Digiboard installed with the given control
|
|
.Ar device
|
|
name.
|
|
A digiboard control
|
|
.Ar device
|
|
is usually of the form
|
|
.Dq /dev/digi Ns Ar N Ns No .ctl
|
|
where
|
|
.Ar N
|
|
is the card number and starts at 0 for the first attached card.
|
|
.Pp
|
|
The following flags are recognised:
|
|
.Bl -tag -width XXXX -offset XXXX
|
|
.It Fl d Ar debug
|
|
If the driver has been compiled with
|
|
.Dv DEBUG
|
|
defined, the following bits from the
|
|
.Ar debug
|
|
variable are used to enable diagnostics in the digiboard driver:
|
|
.Bl -tag -width XXXXXXXXXXXX
|
|
.It 1 ( Em INIT )
|
|
Diagnostics during card attach, detach and initialisation.
|
|
.It 2 ( Em OPEN )
|
|
Diagnostics when opening a port.
|
|
.It 4 ( Em CLOSE )
|
|
Diagnostics when closing a port.
|
|
.It 8 ( Em SET )
|
|
Diagnostics when setting tty device flags.
|
|
.It 16 ( Em INT )
|
|
Diagnostics when processing card events.
|
|
.It 32 ( Em READ )
|
|
Reports return values from port reads.
|
|
.It 64 ( Em WRITE )
|
|
Reports return values from port writes.
|
|
.It 128 ( Em RX )
|
|
Reports receive queue flow control.
|
|
.It 256 ( Em TX )
|
|
Reports transmit queue flow control.
|
|
.It 512 ( Em IRQ )
|
|
Diagnostics during interrupts (enable these with care).
|
|
.It 1024 ( Em MODEM )
|
|
Diagnostics when setting modem status flags.
|
|
.It 2048 ( Em RI )
|
|
Reports when a RING is received.
|
|
.El
|
|
.It Fl i
|
|
Display the card identification string and type id.
|
|
.It Fl r
|
|
Reinitialise the card.
|
|
For boards with external port modules, it is possible to add or remove
|
|
modules and dynamically reprobe the number of ports using this switch.
|
|
All ports on the card must be closed in order to reinitialise the card.
|
|
.Pp
|
|
It is preferable to reinitialise the card rather than reload the entire
|
|
digi module as reinitialisation only affects the specified board rather
|
|
than affecting all attached boards.
|
|
.El
|
|
.Sh BUGS
|
|
It should be possible to reinitialise a board without closing all of the
|
|
existing ports.
|
|
.Sh HISTORY
|
|
The
|
|
.Nm
|
|
command first appeared in
|
|
.Fx 5.0 .
|