442 lines
12 KiB
C
442 lines
12 KiB
C
/*
|
|
* CORTEX-I Frame Grabber driver V1.0
|
|
*
|
|
* Copyright (C) 1994, Paul S. LaFollette, Jr. This software may be used,
|
|
* modified, copied, distributed, and sold, in both source and binary form
|
|
* provided that the above copyright and these terms are retained. Under
|
|
* no circumstances is the author responsible for the proper functioning
|
|
* of this software, nor does the author assume any responsibility
|
|
* for damages incurred with its use.
|
|
*
|
|
* $Id: ctx.c,v 1.6 1995/05/30 08:01:27 rgrimes Exp $
|
|
*/
|
|
|
|
/*
|
|
*
|
|
*
|
|
*
|
|
* Device Driver for CORTEX-I Frame Grabber
|
|
* Made by ImageNation Corporation
|
|
* 1200 N.E. Keyues Road
|
|
* Vancouver, WA 98684 (206) 944-9131
|
|
* (I have no ties to this company, just thought you might want
|
|
* to know how to get in touch with them.)
|
|
*
|
|
* In order to understand this device, you really need to consult the
|
|
* manual which ImageNation provides when you buy the board. (And
|
|
* what a pleasure it is to buy something for a PC and actually get
|
|
* programming information along with it.) I will limit myself here to
|
|
* a few comments which are specific to this driver. See also the file
|
|
* ctxreg.h for definitions of registers and control bits.
|
|
*
|
|
* 1. Although the hardware supports low resolution (256 x 256)
|
|
* acqusition and display, I have not implemented access to
|
|
* these modes in this driver. There are some fairly quirky
|
|
* aspects to the way this board works in low resolution mode,
|
|
* and I don't want to deal with them. Maybe later.
|
|
*
|
|
* 2. Choosing the base address for the video memory: This is set
|
|
* using a combination of hardware and software, using the left
|
|
* most dip switch on the board, and the AB_SELECT bit of control
|
|
* port 1, according to the chart below:
|
|
*
|
|
* Left DIP switch || DOWN | UP |
|
|
* =================================================
|
|
* AB_SELECT = 0 || 0xA0000 | 0xB0000 |
|
|
* -------------------------------------------------
|
|
* AB_SELECT = 1 || 0xD0000 | 0xE0000 |
|
|
* ------------------------------------------------
|
|
*
|
|
* When the RAM_ENABLE bit of control port 1 is clear (0), the
|
|
* video ram is disconnected from the computer bus. This makes
|
|
* it possible, in principle, to share memory space with other
|
|
* devices (such as VGA) which can also disconnect themselves
|
|
* from the bus. It also means that multiple CORTEX-I boards
|
|
* can share the same video memory space. Disconnecting from the
|
|
* bus does not affect the video display of the video ram contents,
|
|
* so that one needs only set the RAM_ENABLE bit when actually
|
|
* reading or writing to memory. The cost of this is low,
|
|
* the benefits to me are great (I need more than one board
|
|
* in my machine, and 0xE0000 is the only address choice that
|
|
* doesn't conflict with anything) so I adopt this strategy here.
|
|
*
|
|
* XXX-Note... this driver has only been tested for the
|
|
* XXX base = 0xE0000 case!
|
|
*
|
|
* 3) There is a deficiency in the documentation from ImageNation, I
|
|
* think. In order to successfully load the lookup table, it is
|
|
* necessary to clear SEE_STORED_VIDEO in control port 0 as well as
|
|
* setting LUT_LOAD_ENABLE in control port 1.
|
|
*
|
|
* 4) This driver accesses video memory through read or write operations.
|
|
* Other functionality is provided through ioctl's, manifest
|
|
* constants for which are defined in ioctl_ctx.h. The ioctl's
|
|
* include:
|
|
* CTX_LIVE Display live video
|
|
* CTX_GRAB Grab a frame of video data
|
|
* CTX_H_ORGANIZE Set things up so that sequential read
|
|
* operations access horizontal lines of
|
|
* pixels.
|
|
* CTX_V_ORGANIZE Set things up so that sequential read
|
|
* operations access vertical lines of
|
|
* pixels.
|
|
* CTX_SET_LUT Set the lookup table from an array
|
|
* of 256 unsigned chars passed as the
|
|
* third parameter to ioctl.
|
|
* CTX_GET_LUT Return the current lookup table to
|
|
* the application as an array of 256
|
|
* unsigned chars. Again the third
|
|
* parameter to the ioctl call.
|
|
*
|
|
* Thus,
|
|
* ioctl(fi, CTX_H_ORGANIZE, 0);
|
|
* lseek(fi, y*512, SEEK_SET);
|
|
* read(fi, buffer, 512);
|
|
*
|
|
* will fill buffer with 512 pixels (unsigned chars) which represent
|
|
* the y-th horizontal line of the image.
|
|
* Similarly,
|
|
* ioctl(fi, CTX_V_ORGANIZE, 0:
|
|
* lseek(fi, x*512+y, SEEK_SET);
|
|
* read(fi, buffer, 10);
|
|
*
|
|
* will read 10 a vertical line of 10 pixels starting at (x,y).
|
|
*
|
|
* Obviously, this sort of ugliness needs to be hidden away from
|
|
* the casual user, with an appropriate set of higher level
|
|
* functions.
|
|
*
|
|
*/
|
|
|
|
#include "ctx.h"
|
|
#if NCTX > 0
|
|
|
|
#include <sys/param.h>
|
|
#include <sys/systm.h>
|
|
#include <sys/ioctl.h>
|
|
#include <sys/proc.h>
|
|
#include <sys/user.h>
|
|
#include <sys/uio.h>
|
|
#include <sys/kernel.h>
|
|
#include <sys/malloc.h>
|
|
#include <sys/devconf.h>
|
|
|
|
#include <i386/isa/isa.h>
|
|
#include <i386/isa/isa_device.h>
|
|
#include <i386/isa/ctxreg.h>
|
|
#include <machine/ioctl_ctx.h>
|
|
|
|
int waitvb(short);
|
|
|
|
/* state flags */
|
|
#define OPEN (0x01) /* device is open */
|
|
|
|
#define UNIT(x) ((x) & 0x07)
|
|
|
|
int ctxprobe(), ctxattach();
|
|
struct isa_driver ctxdriver = {ctxprobe, ctxattach, "ctx"};
|
|
|
|
#define LUTSIZE 256 /* buffer size for Look Up Table (LUT) */
|
|
#define PAGESIZE 65536 /* size of one video page, 1/4 of the screen */
|
|
|
|
/*
|
|
* Per unit shadow registers (because the dumb hardware is RO)
|
|
*/
|
|
|
|
struct ctx_soft_registers {
|
|
u_char *lutp;
|
|
u_char cp0;
|
|
u_char cp1;
|
|
u_char flag;
|
|
short iobase;
|
|
caddr_t maddr;
|
|
int msize;
|
|
} ctx_sr[NCTX];
|
|
|
|
|
|
static struct kern_devconf kdc_ctx[NCTX] = { {
|
|
0, 0, 0, /* filled in by dev_attach */
|
|
"ctx", 0, { MDDT_ISA, 0 },
|
|
isa_generic_externalize, 0, 0, ISA_EXTERNALLEN,
|
|
&kdc_isa0, /* parent */
|
|
0, /* parentdata */
|
|
DC_UNCONFIGURED, /* always start out here */
|
|
"CORTEX-I frame grabber",
|
|
DC_CLS_MISC
|
|
} };
|
|
|
|
static inline void
|
|
ctx_registerdev(struct isa_device *id)
|
|
{
|
|
if(id->id_unit)
|
|
kdc_ctx[id->id_unit] = kdc_ctx[0];
|
|
kdc_ctx[id->id_unit].kdc_unit = id->id_unit;
|
|
kdc_ctx[id->id_unit].kdc_isa = id;
|
|
dev_attach(&kdc_ctx[id->id_unit]);
|
|
}
|
|
|
|
int
|
|
ctxprobe(struct isa_device * devp)
|
|
{
|
|
int status;
|
|
|
|
ctx_registerdev(devp);
|
|
|
|
if (inb(devp->id_iobase) == 0xff) /* 0xff only if board absent */
|
|
status = 0;
|
|
else
|
|
status = 1;
|
|
return (status);
|
|
}
|
|
|
|
int
|
|
ctxattach(struct isa_device * devp)
|
|
{
|
|
struct ctx_soft_registers *sr;
|
|
|
|
sr = &(ctx_sr[devp->id_unit]);
|
|
sr->cp0 = 0; /* zero out the shadow registers */
|
|
sr->cp1 = 0; /* and the open flag. wait for */
|
|
sr->flag = 0; /* open to malloc the LUT space */
|
|
sr->iobase = devp->id_iobase;
|
|
sr->maddr = devp->id_maddr;
|
|
sr->msize = devp->id_msize;
|
|
kdc_ctx[devp->id_unit].kdc_state = DC_IDLE;
|
|
return (1);
|
|
}
|
|
|
|
int
|
|
ctxopen(dev_t dev, int flags, int fmt, struct proc *p)
|
|
{
|
|
struct ctx_soft_registers *sr;
|
|
u_char unit;
|
|
int i;
|
|
|
|
unit = UNIT(minor(dev));
|
|
|
|
/* minor number out of range? */
|
|
|
|
if (unit >= NCTX)
|
|
return (ENXIO);
|
|
sr = &(ctx_sr[unit]);
|
|
|
|
if (sr->flag != 0) /* someone has already opened us */
|
|
return (EBUSY);
|
|
|
|
/* get space for the LUT buffer */
|
|
|
|
sr->lutp = malloc(LUTSIZE, M_DEVBUF, M_WAITOK);
|
|
if (sr->lutp == NULL)
|
|
return (ENOMEM);
|
|
|
|
sr->flag = OPEN;
|
|
kdc_ctx[unit].kdc_state = DC_BUSY;
|
|
|
|
/*
|
|
Set up the shadow registers. We don't actually write these
|
|
values to the control ports until after we finish loading the
|
|
lookup table.
|
|
*/
|
|
sr->cp0 |= SEE_STORED_VIDEO;
|
|
if ((kvtop(sr->maddr) == 0xB0000) || (kvtop(sr->maddr) == 0xE0000))
|
|
sr->cp1 |= AB_SELECT; /* map to B or E if necessary */
|
|
/* but don't enable RAM */
|
|
/*
|
|
Set up the lookup table initially so that it is transparent.
|
|
*/
|
|
|
|
outb(sr->iobase + ctx_cp0, (u_char) 0);
|
|
outb(sr->iobase + ctx_cp1, (u_char) (LUT_LOAD_ENABLE | BLANK_DISPLAY));
|
|
for (i = 0; i < LUTSIZE; i++) {
|
|
outb(sr->iobase + ctx_lutaddr, (u_char) i);
|
|
sr->lutp[i] = (u_char) i;
|
|
outb(sr->iobase + ctx_lutdata, (u_char) sr->lutp[i]);
|
|
}
|
|
/*
|
|
Disable LUT loading, and push the data in the shadow
|
|
registers into the control ports.
|
|
*/
|
|
outb(sr->iobase + ctx_cp0, sr->cp0);
|
|
outb(sr->iobase + ctx_cp1, sr->cp1);
|
|
return (0); /* successful open. All ready to go. */
|
|
}
|
|
|
|
int
|
|
ctxclose(dev_t dev, int flags, int fmt, struct proc *p)
|
|
{
|
|
int unit;
|
|
|
|
unit = UNIT(minor(dev));
|
|
ctx_sr[unit].flag = 0;
|
|
kdc_ctx[unit].kdc_state = DC_IDLE;
|
|
free(ctx_sr[unit].lutp, M_DEVBUF);
|
|
ctx_sr[unit].lutp = NULL;
|
|
return (0);
|
|
}
|
|
|
|
int
|
|
ctxwrite(dev_t dev, struct uio * uio, int ioflag)
|
|
{
|
|
int unit, status = 0;
|
|
int page, count, offset;
|
|
struct ctx_soft_registers *sr;
|
|
|
|
unit = UNIT(minor(dev));
|
|
sr = &(ctx_sr[unit]);
|
|
|
|
page = uio->uio_offset / PAGESIZE;
|
|
offset = uio->uio_offset % PAGESIZE;
|
|
count = min(uio->uio_resid, PAGESIZE - offset);
|
|
while ((page >= 0) && (page <= 3) && (count > 0)) {
|
|
sr->cp0 &= ~3;
|
|
sr->cp0 |= page;
|
|
outb(sr->iobase + ctx_cp0, sr->cp0);
|
|
|
|
/*
|
|
Before doing the uiomove, we need to "connect" the frame buffer
|
|
ram to the machine bus. This is done here so that we can have
|
|
several different boards installed, all sharing the same memory
|
|
space... each board is only "connected" to the bus when its memory
|
|
is actually being read or written. All my instincts tell me that
|
|
I should disable interrupts here, so I have done so.
|
|
*/
|
|
|
|
disable_intr();
|
|
sr->cp1 |= RAM_ENABLE;
|
|
outb(sr->iobase + ctx_cp1, sr->cp1);
|
|
status = uiomove(sr->maddr + offset, count, uio);
|
|
sr->cp1 &= ~RAM_ENABLE;
|
|
outb(sr->iobase + ctx_cp1, sr->cp1);
|
|
enable_intr();
|
|
|
|
page = uio->uio_offset / PAGESIZE;
|
|
offset = uio->uio_offset % PAGESIZE;
|
|
count = min(uio->uio_resid, PAGESIZE - offset);
|
|
}
|
|
if (uio->uio_resid > 0)
|
|
return (ENOSPC);
|
|
else
|
|
return (status);
|
|
}
|
|
|
|
int
|
|
ctxread(dev_t dev, struct uio * uio, int ioflag)
|
|
{
|
|
int unit, status = 0;
|
|
int page, count, offset;
|
|
struct ctx_soft_registers *sr;
|
|
|
|
unit = UNIT(minor(dev));
|
|
sr = &(ctx_sr[unit]);
|
|
|
|
page = uio->uio_offset / PAGESIZE;
|
|
offset = uio->uio_offset % PAGESIZE;
|
|
count = min(uio->uio_resid, PAGESIZE - offset);
|
|
while ((page >= 0) && (page <= 3) && (count > 0)) {
|
|
sr->cp0 &= ~3;
|
|
sr->cp0 |= page;
|
|
outb(sr->iobase + ctx_cp0, sr->cp0);
|
|
/*
|
|
Before doing the uiomove, we need to "connect" the frame buffer
|
|
ram to the machine bus. This is done here so that we can have
|
|
several different boards installed, all sharing the same memory
|
|
space... each board is only "connected" to the bus when its memory
|
|
is actually being read or written. All my instincts tell me that
|
|
I should disable interrupts here, so I have done so.
|
|
*/
|
|
disable_intr();
|
|
sr->cp1 |= RAM_ENABLE;
|
|
outb(sr->iobase + ctx_cp1, sr->cp1);
|
|
status = uiomove(sr->maddr + offset, count, uio);
|
|
sr->cp1 &= ~RAM_ENABLE;
|
|
outb(sr->iobase + ctx_cp1, sr->cp1);
|
|
enable_intr();
|
|
|
|
page = uio->uio_offset / PAGESIZE;
|
|
offset = uio->uio_offset % PAGESIZE;
|
|
count = min(uio->uio_resid, PAGESIZE - offset);
|
|
}
|
|
if (uio->uio_resid > 0)
|
|
return (ENOSPC);
|
|
else
|
|
return (status);
|
|
}
|
|
|
|
int
|
|
ctxioctl(dev_t dev, int cmd, caddr_t data, int flags, struct proc *p)
|
|
{
|
|
int error;
|
|
int unit, i;
|
|
struct ctx_soft_registers *sr;
|
|
|
|
error = 0;
|
|
unit = UNIT(minor(dev));
|
|
sr = &(ctx_sr[unit]);
|
|
|
|
switch (cmd) {
|
|
case CTX_LIVE:
|
|
sr->cp0 &= ~SEE_STORED_VIDEO;
|
|
outb(sr->iobase + ctx_cp0, sr->cp0);
|
|
break;
|
|
case CTX_GRAB:
|
|
sr->cp0 &= ~SEE_STORED_VIDEO;
|
|
outb(sr->iobase + ctx_cp0, sr->cp0);
|
|
sr->cp0 |= ACQUIRE;
|
|
if (waitvb(sr->iobase)) /* wait for vert blank to start
|
|
* acquire */
|
|
error = ENODEV;
|
|
outb(sr->iobase + ctx_cp0, sr->cp0);
|
|
if (waitvb(sr->iobase)) /* wait for two more to finish acquire */
|
|
error = ENODEV;
|
|
if (waitvb(sr->iobase))
|
|
error = ENODEV;
|
|
sr->cp0 &= ~ACQUIRE; /* turn off acquire and turn on
|
|
* display */
|
|
sr->cp0 |= SEE_STORED_VIDEO;
|
|
outb(sr->iobase + ctx_cp0, sr->cp0);
|
|
break;
|
|
case CTX_H_ORGANIZE:
|
|
sr->cp0 &= ~PAGE_ROTATE;
|
|
outb(sr->iobase + ctx_cp0, sr->cp0);
|
|
break;
|
|
case CTX_V_ORGANIZE:
|
|
sr->cp0 |= PAGE_ROTATE;
|
|
outb(sr->iobase + ctx_cp0, sr->cp0);
|
|
break;
|
|
case CTX_SET_LUT:
|
|
bcopy((u_char *) data, sr->lutp, LUTSIZE);
|
|
outb(sr->iobase + ctx_cp0, (u_char) 0);
|
|
outb(sr->iobase + ctx_cp1, (u_char) (LUT_LOAD_ENABLE | BLANK_DISPLAY));
|
|
for (i = 0; i < LUTSIZE; i++) {
|
|
outb(sr->iobase + ctx_lutaddr, i);
|
|
outb(sr->iobase + ctx_lutdata, sr->lutp[i]);
|
|
}
|
|
outb(sr->iobase + ctx_cp0, sr->cp0); /* restore control
|
|
* registers */
|
|
outb(sr->iobase + ctx_cp1, sr->cp1);
|
|
break;
|
|
case CTX_GET_LUT:
|
|
bcopy(sr->lutp, (u_char *) data, LUTSIZE);
|
|
break;
|
|
default:
|
|
error = ENODEV;
|
|
}
|
|
|
|
return (error);
|
|
}
|
|
|
|
int
|
|
waitvb(short port)
|
|
{ /* wait for a vertical blank, */
|
|
if (inb(port) == 0xff) /* 0xff means no board present */
|
|
return (1);
|
|
|
|
while ((inb(port) & VERTICAL_BLANK) != 0) {
|
|
}
|
|
while ((inb(port) & VERTICAL_BLANK) == 0) {
|
|
}
|
|
|
|
return (0);
|
|
}
|
|
#endif /* NCTX > 0 */
|