d/freebsd-skq
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
f6b6404d7f
freebsd-skq/sys/dev/bge/if_bge.c
ps f6b6404d7f - Move bge_phy_hack into the phy code and implement the various DSP 
patch workarounds for each phy revision.
  Obtained from: NetBSD & Broadcom Linux driver

- Disable AUTOPOLL when accessing the PHY as it may cause PCI errors.
  Obtained from: NetBSD

- Check the UPDATED bit in the status block so the driver knows
  that the status block as indeed changed since the last access.
  Broadcom documentation states drivers should unset the UPDATED/CHANGED
  bits after reading them.

- When changing media types, first loop the phy then set the media.
  Broadcom documentation and Linux drivers do this and I observed
  much better handling of link after this change.

- Broadcom documentation states that for 1000BaseT operation,
  autonegotiation must be enabled.  Fix hard coding of media so that
  the driver only advertises 1000BaseT as the supported media type
  and enable autonegotition.

- Only set Master/Slave on the 5701.
  Obtained from Broadcom Linux driver.
2003-05-03 19:06:50 +00:00

2728 lines
69 KiB
C
Raw Blame History

/*
* Copyright (c) 2001 Wind River Systems
* Copyright (c) 1997, 1998, 1999, 2001
* Bill Paul <wpaul@windriver.com>. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software
* must display the following acknowledgement:
* This product includes software developed by Bill Paul.
* 4. Neither the name of the author nor the names of any co-contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
* THE POSSIBILITY OF SUCH DAMAGE.
*/
/*
* Broadcom BCM570x family gigabit ethernet driver for FreeBSD.
*
* The Broadcom BCM5700 is based on technology originally developed by
* Alteon Networks as part of the Tigon I and Tigon II gigabit ethernet
* MAC chips. The BCM5700, sometimes refered to as the Tigon III, has
* two on-board MIPS R4000 CPUs and can have as much as 16MB of external
* SSRAM. The BCM5700 supports TCP, UDP and IP checksum offload, jumbo
* frames, highly configurable RX filtering, and 16 RX and TX queues
* (which, along with RX filter rules, can be used for QOS applications).
* Other features, such as TCP segmentation, may be available as part
* of value-added firmware updates. Unlike the Tigon I and Tigon II,
* firmware images can be stored in hardware and need not be compiled
* into the driver.
*
* The BCM5700 supports the PCI v2.2 and PCI-X v1.0 standards, and will
* function in a 32-bit/64-bit 33/66Mhz bus, or a 64-bit/133Mhz bus.
*
* The BCM5701 is a single-chip solution incorporating both the BCM5700
* MAC and a BCM5401 10/100/1000 PHY. Unlike the BCM5700, the BCM5701
* does not support external SSRAM.
*
* Broadcom also produces a variation of the BCM5700 under the "Altima"
* brand name, which is functionally similar but lacks PCI-X support.
*
* Without external SSRAM, you can only have at most 4 TX rings,
* and the use of the mini RX ring is disabled. This seems to imply
* that these features are simply not available on the BCM5701. As a
* result, this driver does not implement any support for the mini RX
* ring.
*/
#include <sys/cdefs.h>
__FBSDID("$FreeBSD$");
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/sockio.h>
#include <sys/mbuf.h>
#include <sys/malloc.h>
#include <sys/kernel.h>
#include <sys/socket.h>
#include <sys/queue.h>
#include <net/if.h>
#include <net/if_arp.h>
#include <net/ethernet.h>
#include <net/if_dl.h>
#include <net/if_media.h>
#include <net/bpf.h>
#include <net/if_types.h>
#include <net/if_vlan_var.h>
#include <netinet/in_systm.h>
#include <netinet/in.h>
#include <netinet/ip.h>
#include <vm/vm.h> /* for vtophys */
#include <vm/pmap.h> /* for vtophys */
#include <machine/clock.h> /* for DELAY */
#include <machine/bus_memio.h>
#include <machine/bus.h>
#include <machine/resource.h>
#include <sys/bus.h>
#include <sys/rman.h>
#include <dev/mii/mii.h>
#include <dev/mii/miivar.h>
#include "miidevs.h"
#include <dev/mii/brgphyreg.h>
#include <pci/pcireg.h>
#include <pci/pcivar.h>
#include <dev/bge/if_bgereg.h>
#define BGE_CSUM_FEATURES (CSUM_IP | CSUM_TCP | CSUM_UDP)
MODULE_DEPEND(bge, pci, 1, 1, 1);
MODULE_DEPEND(bge, ether, 1, 1, 1);
MODULE_DEPEND(bge, miibus, 1, 1, 1);
/* "controller miibus0" required. See GENERIC if you get errors here. */
#include "miibus_if.h"
/*
* Various supported device vendors/types and their names. Note: the
* spec seems to indicate that the hardware still has Alteon's vendor
* ID burned into it, though it will always be overriden by the vendor
* ID in the EEPROM. Just to be safe, we cover all possibilities.
*/
#define BGE_DEVDESC_MAX 64 /* Maximum device description length */
static struct bge_type bge_devs[] = {
{ ALT_VENDORID, ALT_DEVICEID_BCM5700,
"Broadcom BCM5700 Gigabit Ethernet" },
{ ALT_VENDORID, ALT_DEVICEID_BCM5701,
"Broadcom BCM5701 Gigabit Ethernet" },
{ BCOM_VENDORID, BCOM_DEVICEID_BCM5700,
"Broadcom BCM5700 Gigabit Ethernet" },
{ BCOM_VENDORID, BCOM_DEVICEID_BCM5701,
"Broadcom BCM5701 Gigabit Ethernet" },
{ BCOM_VENDORID, BCOM_DEVICEID_BCM5702X,
"Broadcom BCM5702X Gigabit Ethernet" },
{ BCOM_VENDORID, BCOM_DEVICEID_BCM5703X,
"Broadcom BCM5703X Gigabit Ethernet" },
{ BCOM_VENDORID, BCOM_DEVICEID_BCM5704C,
"Broadcom BCM5704C Dual Gigabit Ethernet" },
{ BCOM_VENDORID, BCOM_DEVICEID_BCM5704S,
"Broadcom BCM5704S Dual Gigabit Ethernet" },
{ SK_VENDORID, SK_DEVICEID_ALTIMA,
"SysKonnect Gigabit Ethernet" },
{ ALTIMA_VENDORID, ALTIMA_DEVICE_AC1000,
"Altima AC1000 Gigabit Ethernet" },
{ ALTIMA_VENDORID, ALTIMA_DEVICE_AC9100,
"Altima AC9100 Gigabit Ethernet" },
{ 0, 0, NULL }
};
static int bge_probe (device_t);
static int bge_attach (device_t);
static int bge_detach (device_t);
static void bge_release_resources
(struct bge_softc *);
static void bge_txeof (struct bge_softc *);
static void bge_rxeof (struct bge_softc *);
static void bge_tick (void *);
static void bge_stats_update (struct bge_softc *);
static int bge_encap (struct bge_softc *, struct mbuf *,
u_int32_t *);
static void bge_intr (void *);
static void bge_start (struct ifnet *);
static int bge_ioctl (struct ifnet *, u_long, caddr_t);
static void bge_init (void *);
static void bge_stop (struct bge_softc *);
static void bge_watchdog (struct ifnet *);
static void bge_shutdown (device_t);
static int bge_ifmedia_upd (struct ifnet *);
static void bge_ifmedia_sts (struct ifnet *, struct ifmediareq *);
static u_int8_t bge_eeprom_getbyte (struct bge_softc *, int, u_int8_t *);
static int bge_read_eeprom (struct bge_softc *, caddr_t, int, int);
static u_int32_t bge_crc (caddr_t);
static void bge_setmulti (struct bge_softc *);
static void bge_handle_events (struct bge_softc *);
static int bge_alloc_jumbo_mem (struct bge_softc *);
static void bge_free_jumbo_mem (struct bge_softc *);
static void *bge_jalloc (struct bge_softc *);
static void bge_jfree (void *, void *);
static int bge_newbuf_std (struct bge_softc *, int, struct mbuf *);
static int bge_newbuf_jumbo (struct bge_softc *, int, struct mbuf *);
static int bge_init_rx_ring_std (struct bge_softc *);
static void bge_free_rx_ring_std (struct bge_softc *);
static int bge_init_rx_ring_jumbo (struct bge_softc *);
static void bge_free_rx_ring_jumbo (struct bge_softc *);
static void bge_free_tx_ring (struct bge_softc *);
static int bge_init_tx_ring (struct bge_softc *);
static int bge_chipinit (struct bge_softc *);
static int bge_blockinit (struct bge_softc *);
#ifdef notdef
static u_int8_t bge_vpd_readbyte(struct bge_softc *, int);
static void bge_vpd_read_res (struct bge_softc *, struct vpd_res *, int);
static void bge_vpd_read (struct bge_softc *);
#endif
static u_int32_t bge_readmem_ind
(struct bge_softc *, int);
static void bge_writemem_ind (struct bge_softc *, int, int);
#ifdef notdef
static u_int32_t bge_readreg_ind
(struct bge_softc *, int);
#endif
static void bge_writereg_ind (struct bge_softc *, int, int);
static int bge_miibus_readreg (device_t, int, int);
static int bge_miibus_writereg (device_t, int, int, int);
static void bge_miibus_statchg (device_t);
static void bge_reset (struct bge_softc *);
static device_method_t bge_methods[] = {
/* Device interface */
DEVMETHOD(device_probe, bge_probe),
DEVMETHOD(device_attach, bge_attach),
DEVMETHOD(device_detach, bge_detach),
DEVMETHOD(device_shutdown, bge_shutdown),
/* bus interface */
DEVMETHOD(bus_print_child, bus_generic_print_child),
DEVMETHOD(bus_driver_added, bus_generic_driver_added),
/* MII interface */
DEVMETHOD(miibus_readreg, bge_miibus_readreg),
DEVMETHOD(miibus_writereg, bge_miibus_writereg),
DEVMETHOD(miibus_statchg, bge_miibus_statchg),
{ 0, 0 }
};
static driver_t bge_driver = {
"bge",
bge_methods,
sizeof(struct bge_softc)
};
static devclass_t bge_devclass;
DRIVER_MODULE(bge, pci, bge_driver, bge_devclass, 0, 0);
DRIVER_MODULE(miibus, bge, miibus_driver, miibus_devclass, 0, 0);
static u_int32_t
bge_readmem_ind(sc, off)
struct bge_softc *sc;
int off;
{
device_t dev;
dev = sc->bge_dev;
pci_write_config(dev, BGE_PCI_MEMWIN_BASEADDR, off, 4);
return(pci_read_config(dev, BGE_PCI_MEMWIN_DATA, 4));
}
static void
bge_writemem_ind(sc, off, val)
struct bge_softc *sc;
int off, val;
{
device_t dev;
dev = sc->bge_dev;
pci_write_config(dev, BGE_PCI_MEMWIN_BASEADDR, off, 4);
pci_write_config(dev, BGE_PCI_MEMWIN_DATA, val, 4);
return;
}
#ifdef notdef
static u_int32_t
bge_readreg_ind(sc, off)
struct bge_softc *sc;
int off;
{
device_t dev;
dev = sc->bge_dev;
pci_write_config(dev, BGE_PCI_REG_BASEADDR, off, 4);
return(pci_read_config(dev, BGE_PCI_REG_DATA, 4));
}
#endif
static void
bge_writereg_ind(sc, off, val)
struct bge_softc *sc;
int off, val;
{
device_t dev;
dev = sc->bge_dev;
pci_write_config(dev, BGE_PCI_REG_BASEADDR, off, 4);
pci_write_config(dev, BGE_PCI_REG_DATA, val, 4);
return;
}
#ifdef notdef
static u_int8_t
bge_vpd_readbyte(sc, addr)
struct bge_softc *sc;
int addr;
{
int i;
device_t dev;
u_int32_t val;
dev = sc->bge_dev;
pci_write_config(dev, BGE_PCI_VPD_ADDR, addr, 2);
for (i = 0; i < BGE_TIMEOUT * 10; i++) {
DELAY(10);
if (pci_read_config(dev, BGE_PCI_VPD_ADDR, 2) & BGE_VPD_FLAG)
break;
}
if (i == BGE_TIMEOUT) {
printf("bge%d: VPD read timed out\n", sc->bge_unit);
return(0);
}
val = pci_read_config(dev, BGE_PCI_VPD_DATA, 4);
return((val >> ((addr % 4) * 8)) & 0xFF);
}
static void
bge_vpd_read_res(sc, res, addr)
struct bge_softc *sc;
struct vpd_res *res;
int addr;
{
int i;
u_int8_t *ptr;
ptr = (u_int8_t *)res;
for (i = 0; i < sizeof(struct vpd_res); i++)
ptr[i] = bge_vpd_readbyte(sc, i + addr);
return;
}
static void
bge_vpd_read(sc)
struct bge_softc *sc;
{
int pos = 0, i;
struct vpd_res res;
if (sc->bge_vpd_prodname != NULL)
free(sc->bge_vpd_prodname, M_DEVBUF);
if (sc->bge_vpd_readonly != NULL)
free(sc->bge_vpd_readonly, M_DEVBUF);
sc->bge_vpd_prodname = NULL;
sc->bge_vpd_readonly = NULL;
bge_vpd_read_res(sc, &res, pos);
if (res.vr_id != VPD_RES_ID) {
printf("bge%d: bad VPD resource id: expected %x got %x\n",
sc->bge_unit, VPD_RES_ID, res.vr_id);
return;
}
pos += sizeof(res);
sc->bge_vpd_prodname = malloc(res.vr_len + 1, M_DEVBUF, M_NOWAIT);
for (i = 0; i < res.vr_len; i++)
sc->bge_vpd_prodname[i] = bge_vpd_readbyte(sc, i + pos);
sc->bge_vpd_prodname[i] = '\0';
pos += i;
bge_vpd_read_res(sc, &res, pos);
if (res.vr_id != VPD_RES_READ) {
printf("bge%d: bad VPD resource id: expected %x got %x\n",
sc->bge_unit, VPD_RES_READ, res.vr_id);
return;
}
pos += sizeof(res);
sc->bge_vpd_readonly = malloc(res.vr_len, M_DEVBUF, M_NOWAIT);
for (i = 0; i < res.vr_len + 1; i++)
sc->bge_vpd_readonly[i] = bge_vpd_readbyte(sc, i + pos);
return;
}
#endif
/*
* Read a byte of data stored in the EEPROM at address 'addr.' The
* BCM570x supports both the traditional bitbang interface and an
* auto access interface for reading the EEPROM. We use the auto
* access method.
*/
static u_int8_t
bge_eeprom_getbyte(sc, addr, dest)
struct bge_softc *sc;
int addr;
u_int8_t *dest;
{
int i;
u_int32_t byte = 0;
/*
* Enable use of auto EEPROM access so we can avoid
* having to use the bitbang method.
*/
BGE_SETBIT(sc, BGE_MISC_LOCAL_CTL, BGE_MLC_AUTO_EEPROM);
/* Reset the EEPROM, load the clock period. */
CSR_WRITE_4(sc, BGE_EE_ADDR,
BGE_EEADDR_RESET|BGE_EEHALFCLK(BGE_HALFCLK_384SCL));
DELAY(20);
/* Issue the read EEPROM command. */
CSR_WRITE_4(sc, BGE_EE_ADDR, BGE_EE_READCMD | addr);
/* Wait for completion */
for(i = 0; i < BGE_TIMEOUT * 10; i++) {
DELAY(10);
if (CSR_READ_4(sc, BGE_EE_ADDR) & BGE_EEADDR_DONE)
break;
}
if (i == BGE_TIMEOUT) {
printf("bge%d: eeprom read timed out\n", sc->bge_unit);
return(0);
}
/* Get result. */
byte = CSR_READ_4(sc, BGE_EE_DATA);
*dest = (byte >> ((addr % 4) * 8)) & 0xFF;
return(0);
}
/*
* Read a sequence of bytes from the EEPROM.
*/
static int
bge_read_eeprom(sc, dest, off, cnt)
struct bge_softc *sc;
caddr_t dest;
int off;
int cnt;
{
int err = 0, i;
u_int8_t byte = 0;
for (i = 0; i < cnt; i++) {
err = bge_eeprom_getbyte(sc, off + i, &byte);
if (err)
break;
*(dest + i) = byte;
}
return(err ? 1 : 0);
}
static int
bge_miibus_readreg(dev, phy, reg)
device_t dev;
int phy, reg;
{
struct bge_softc *sc;
struct ifnet *ifp;
u_int32_t val, autopoll;
int i;
sc = device_get_softc(dev);
ifp = &sc->arpcom.ac_if;
if (phy != 1)
switch(sc->bge_asicrev) {
case BGE_ASICREV_BCM5701_B5:
case BGE_ASICREV_BCM5703_A2:
case BGE_ASICREV_BCM5704_A0:
return(0);
}
/* Reading with autopolling on may trigger PCI errors */
autopoll = CSR_READ_4(sc, BGE_MI_MODE);
if (autopoll & BGE_MIMODE_AUTOPOLL) {
BGE_CLRBIT(sc, BGE_MI_MODE, BGE_MIMODE_AUTOPOLL);
DELAY(40);
}
CSR_WRITE_4(sc, BGE_MI_COMM, BGE_MICMD_READ|BGE_MICOMM_BUSY|
BGE_MIPHY(phy)|BGE_MIREG(reg));
for (i = 0; i < BGE_TIMEOUT; i++) {
val = CSR_READ_4(sc, BGE_MI_COMM);
if (!(val & BGE_MICOMM_BUSY))
break;
}
if (i == BGE_TIMEOUT) {
printf("bge%d: PHY read timed out\n", sc->bge_unit);
val = 0;
goto done;
}
val = CSR_READ_4(sc, BGE_MI_COMM);
done:
if (autopoll & BGE_MIMODE_AUTOPOLL) {
BGE_SETBIT(sc, BGE_MI_MODE, BGE_MIMODE_AUTOPOLL);
DELAY(40);
}
if (val & BGE_MICOMM_READFAIL)
return(0);
return(val & 0xFFFF);
}
static int
bge_miibus_writereg(dev, phy, reg, val)
device_t dev;
int phy, reg, val;
{
struct bge_softc *sc;
u_int32_t autopoll;
int i;
sc = device_get_softc(dev);
/* Reading with autopolling on may trigger PCI errors */
autopoll = CSR_READ_4(sc, BGE_MI_MODE);
if (autopoll & BGE_MIMODE_AUTOPOLL) {
BGE_CLRBIT(sc, BGE_MI_MODE, BGE_MIMODE_AUTOPOLL);
DELAY(40);
}
CSR_WRITE_4(sc, BGE_MI_COMM, BGE_MICMD_WRITE|BGE_MICOMM_BUSY|
BGE_MIPHY(phy)|BGE_MIREG(reg)|val);
for (i = 0; i < BGE_TIMEOUT; i++) {
if (!(CSR_READ_4(sc, BGE_MI_COMM) & BGE_MICOMM_BUSY))
break;
}
if (autopoll & BGE_MIMODE_AUTOPOLL) {
BGE_SETBIT(sc, BGE_MI_MODE, BGE_MIMODE_AUTOPOLL);
DELAY(40);
}
if (i == BGE_TIMEOUT) {
printf("bge%d: PHY read timed out\n", sc->bge_unit);
return(0);
}
return(0);
}
static void
bge_miibus_statchg(dev)
device_t dev;
{
struct bge_softc *sc;
struct mii_data *mii;
sc = device_get_softc(dev);
mii = device_get_softc(sc->bge_miibus);
BGE_CLRBIT(sc, BGE_MAC_MODE, BGE_MACMODE_PORTMODE);
if (IFM_SUBTYPE(mii->mii_media_active) == IFM_1000_T) {
BGE_SETBIT(sc, BGE_MAC_MODE, BGE_PORTMODE_GMII);
} else {
BGE_SETBIT(sc, BGE_MAC_MODE, BGE_PORTMODE_MII);
}
if ((mii->mii_media_active & IFM_GMASK) == IFM_FDX) {
BGE_CLRBIT(sc, BGE_MAC_MODE, BGE_MACMODE_HALF_DUPLEX);
} else {
BGE_SETBIT(sc, BGE_MAC_MODE, BGE_MACMODE_HALF_DUPLEX);
}
return;
}
/*
* Handle events that have triggered interrupts.
*/
static void
bge_handle_events(sc)
struct bge_softc *sc;
{
return;
}
/*
* Memory management for jumbo frames.
*/
static int
bge_alloc_jumbo_mem(sc)
struct bge_softc *sc;
{
caddr_t ptr;
register int i;
struct bge_jpool_entry *entry;
/* Grab a big chunk o' storage. */
sc->bge_cdata.bge_jumbo_buf = contigmalloc(BGE_JMEM, M_DEVBUF,
M_NOWAIT, 0, 0xffffffff, PAGE_SIZE, 0);
if (sc->bge_cdata.bge_jumbo_buf == NULL) {
printf("bge%d: no memory for jumbo buffers!\n", sc->bge_unit);
return(ENOBUFS);
}
SLIST_INIT(&sc->bge_jfree_listhead);
SLIST_INIT(&sc->bge_jinuse_listhead);
/*
* Now divide it up into 9K pieces and save the addresses
* in an array.
*/
ptr = sc->bge_cdata.bge_jumbo_buf;
for (i = 0; i < BGE_JSLOTS; i++) {
sc->bge_cdata.bge_jslots[i] = ptr;
ptr += BGE_JLEN;
entry = malloc(sizeof(struct bge_jpool_entry),
M_DEVBUF, M_NOWAIT);
if (entry == NULL) {
contigfree(sc->bge_cdata.bge_jumbo_buf,
BGE_JMEM, M_DEVBUF);
sc->bge_cdata.bge_jumbo_buf = NULL;
printf("bge%d: no memory for jumbo "
"buffer queue!\n", sc->bge_unit);
return(ENOBUFS);
}
entry->slot = i;
SLIST_INSERT_HEAD(&sc->bge_jfree_listhead,
entry, jpool_entries);
}
return(0);
}
static void
bge_free_jumbo_mem(sc)
struct bge_softc *sc;
{
int i;
struct bge_jpool_entry *entry;
for (i = 0; i < BGE_JSLOTS; i++) {
entry = SLIST_FIRST(&sc->bge_jfree_listhead);
SLIST_REMOVE_HEAD(&sc->bge_jfree_listhead, jpool_entries);
free(entry, M_DEVBUF);
}
contigfree(sc->bge_cdata.bge_jumbo_buf, BGE_JMEM, M_DEVBUF);
return;
}
/*
* Allocate a jumbo buffer.
*/
static void *
bge_jalloc(sc)
struct bge_softc *sc;
{
struct bge_jpool_entry *entry;
entry = SLIST_FIRST(&sc->bge_jfree_listhead);
if (entry == NULL) {
printf("bge%d: no free jumbo buffers\n", sc->bge_unit);
return(NULL);
}
SLIST_REMOVE_HEAD(&sc->bge_jfree_listhead, jpool_entries);
SLIST_INSERT_HEAD(&sc->bge_jinuse_listhead, entry, jpool_entries);
return(sc->bge_cdata.bge_jslots[entry->slot]);
}
/*
* Release a jumbo buffer.
*/
static void
bge_jfree(buf, args)
void *buf;
void *args;
{
struct bge_jpool_entry *entry;
struct bge_softc *sc;
int i;
/* Extract the softc struct pointer. */
sc = (struct bge_softc *)args;
if (sc == NULL)
panic("bge_jfree: can't find softc pointer!");
/* calculate the slot this buffer belongs to */
i = ((vm_offset_t)buf
- (vm_offset_t)sc->bge_cdata.bge_jumbo_buf) / BGE_JLEN;
if ((i < 0) || (i >= BGE_JSLOTS))
panic("bge_jfree: asked to free buffer that we don't manage!");
entry = SLIST_FIRST(&sc->bge_jinuse_listhead);
if (entry == NULL)
panic("bge_jfree: buffer not in use!");
entry->slot = i;
SLIST_REMOVE_HEAD(&sc->bge_jinuse_listhead, jpool_entries);
SLIST_INSERT_HEAD(&sc->bge_jfree_listhead, entry, jpool_entries);
return;
}
/*
* Intialize a standard receive ring descriptor.
*/
static int
bge_newbuf_std(sc, i, m)
struct bge_softc *sc;
int i;
struct mbuf *m;
{
struct mbuf *m_new = NULL;
struct bge_rx_bd *r;
if (m == NULL) {
MGETHDR(m_new, M_DONTWAIT, MT_DATA);
if (m_new == NULL) {
return(ENOBUFS);
}
MCLGET(m_new, M_DONTWAIT);
if (!(m_new->m_flags & M_EXT)) {
m_freem(m_new);
return(ENOBUFS);
}
m_new->m_len = m_new->m_pkthdr.len = MCLBYTES;
} else {
m_new = m;
m_new->m_len = m_new->m_pkthdr.len = MCLBYTES;
m_new->m_data = m_new->m_ext.ext_buf;
}
if (!sc->bge_rx_alignment_bug)
m_adj(m_new, ETHER_ALIGN);
sc->bge_cdata.bge_rx_std_chain[i] = m_new;
r = &sc->bge_rdata->bge_rx_std_ring[i];
BGE_HOSTADDR(r->bge_addr) = vtophys(mtod(m_new, caddr_t));
r->bge_flags = BGE_RXBDFLAG_END;
r->bge_len = m_new->m_len;
r->bge_idx = i;
return(0);
}
/*
* Initialize a jumbo receive ring descriptor. This allocates
* a jumbo buffer from the pool managed internally by the driver.
*/
static int
bge_newbuf_jumbo(sc, i, m)
struct bge_softc *sc;
int i;
struct mbuf *m;
{
struct mbuf *m_new = NULL;
struct bge_rx_bd *r;
if (m == NULL) {
caddr_t *buf = NULL;
/* Allocate the mbuf. */
MGETHDR(m_new, M_DONTWAIT, MT_DATA);
if (m_new == NULL) {
return(ENOBUFS);
}
/* Allocate the jumbo buffer */
buf = bge_jalloc(sc);
if (buf == NULL) {
m_freem(m_new);
printf("bge%d: jumbo allocation failed "
"-- packet dropped!\n", sc->bge_unit);
return(ENOBUFS);
}
/* Attach the buffer to the mbuf. */
m_new->m_data = (void *) buf;
m_new->m_len = m_new->m_pkthdr.len = BGE_JUMBO_FRAMELEN;
MEXTADD(m_new, buf, BGE_JUMBO_FRAMELEN, bge_jfree,
(struct bge_softc *)sc, 0, EXT_NET_DRV);
} else {
m_new = m;
m_new->m_data = m_new->m_ext.ext_buf;
m_new->m_ext.ext_size = BGE_JUMBO_FRAMELEN;
}
if (!sc->bge_rx_alignment_bug)
m_adj(m_new, ETHER_ALIGN);
/* Set up the descriptor. */
r = &sc->bge_rdata->bge_rx_jumbo_ring[i];
sc->bge_cdata.bge_rx_jumbo_chain[i] = m_new;
BGE_HOSTADDR(r->bge_addr) = vtophys(mtod(m_new, caddr_t));
r->bge_flags = BGE_RXBDFLAG_END|BGE_RXBDFLAG_JUMBO_RING;
r->bge_len = m_new->m_len;
r->bge_idx = i;
return(0);
}
/*
* The standard receive ring has 512 entries in it. At 2K per mbuf cluster,
* that's 1MB or memory, which is a lot. For now, we fill only the first
* 256 ring entries and hope that our CPU is fast enough to keep up with
* the NIC.
*/
static int
bge_init_rx_ring_std(sc)
struct bge_softc *sc;
{
int i;
for (i = 0; i < BGE_SSLOTS; i++) {
if (bge_newbuf_std(sc, i, NULL) == ENOBUFS)
return(ENOBUFS);
};
sc->bge_std = i - 1;
CSR_WRITE_4(sc, BGE_MBX_RX_STD_PROD_LO, sc->bge_std);
return(0);
}
static void
bge_free_rx_ring_std(sc)
struct bge_softc *sc;
{
int i;
for (i = 0; i < BGE_STD_RX_RING_CNT; i++) {
if (sc->bge_cdata.bge_rx_std_chain[i] != NULL) {
m_freem(sc->bge_cdata.bge_rx_std_chain[i]);
sc->bge_cdata.bge_rx_std_chain[i] = NULL;
}
bzero((char *)&sc->bge_rdata->bge_rx_std_ring[i],
sizeof(struct bge_rx_bd));
}
return;
}
static int
bge_init_rx_ring_jumbo(sc)
struct bge_softc *sc;
{
int i;
struct bge_rcb *rcb;
for (i = 0; i < BGE_JUMBO_RX_RING_CNT; i++) {
if (bge_newbuf_jumbo(sc, i, NULL) == ENOBUFS)
return(ENOBUFS);
};
sc->bge_jumbo = i - 1;
rcb = &sc->bge_rdata->bge_info.bge_jumbo_rx_rcb;
rcb->bge_maxlen_flags = BGE_RCB_MAXLEN_FLAGS(0, 0);
CSR_WRITE_4(sc, BGE_RX_JUMBO_RCB_MAXLEN_FLAGS, rcb->bge_maxlen_flags);
CSR_WRITE_4(sc, BGE_MBX_RX_JUMBO_PROD_LO, sc->bge_jumbo);
return(0);
}
static void
bge_free_rx_ring_jumbo(sc)
struct bge_softc *sc;
{
int i;
for (i = 0; i < BGE_JUMBO_RX_RING_CNT; i++) {
if (sc->bge_cdata.bge_rx_jumbo_chain[i] != NULL) {
m_freem(sc->bge_cdata.bge_rx_jumbo_chain[i]);
sc->bge_cdata.bge_rx_jumbo_chain[i] = NULL;
}
bzero((char *)&sc->bge_rdata->bge_rx_jumbo_ring[i],
sizeof(struct bge_rx_bd));
}
return;
}
static void
bge_free_tx_ring(sc)
struct bge_softc *sc;
{
int i;
if (sc->bge_rdata->bge_tx_ring == NULL)
return;
for (i = 0; i < BGE_TX_RING_CNT; i++) {
if (sc->bge_cdata.bge_tx_chain[i] != NULL) {
m_freem(sc->bge_cdata.bge_tx_chain[i]);
sc->bge_cdata.bge_tx_chain[i] = NULL;
}
bzero((char *)&sc->bge_rdata->bge_tx_ring[i],
sizeof(struct bge_tx_bd));
}
return;
}
static int
bge_init_tx_ring(sc)
struct bge_softc *sc;
{
sc->bge_txcnt = 0;
sc->bge_tx_saved_considx = 0;
CSR_WRITE_4(sc, BGE_MBX_TX_HOST_PROD0_LO, 0);
CSR_WRITE_4(sc, BGE_MBX_TX_NIC_PROD0_LO, 0);
return(0);
}
#define BGE_POLY 0xEDB88320
static u_int32_t
bge_crc(addr)
caddr_t addr;
{
u_int32_t idx, bit, data, crc;
/* Compute CRC for the address value. */
crc = 0xFFFFFFFF; /* initial value */
for (idx = 0; idx < 6; idx++) {
for (data = *addr++, bit = 0; bit < 8; bit++, data >>= 1)
crc = (crc >> 1) ^ (((crc ^ data) & 1) ? BGE_POLY : 0);
}
return(crc & 0x7F);
}
static void
bge_setmulti(sc)
struct bge_softc *sc;
{
struct ifnet *ifp;
struct ifmultiaddr *ifma;
u_int32_t hashes[4] = { 0, 0, 0, 0 };
int h, i;
ifp = &sc->arpcom.ac_if;
if (ifp->if_flags & IFF_ALLMULTI || ifp->if_flags & IFF_PROMISC) {
for (i = 0; i < 4; i++)
CSR_WRITE_4(sc, BGE_MAR0 + (i * 4), 0xFFFFFFFF);
return;
}
/* First, zot all the existing filters. */
for (i = 0; i < 4; i++)
CSR_WRITE_4(sc, BGE_MAR0 + (i * 4), 0);
/* Now program new ones. */
TAILQ_FOREACH(ifma, &ifp->if_multiaddrs, ifma_link) {
if (ifma->ifma_addr->sa_family != AF_LINK)
continue;
h = bge_crc(LLADDR((struct sockaddr_dl *)ifma->ifma_addr));
hashes[(h & 0x60) >> 5] |= 1 << (h & 0x1F);
}
for (i = 0; i < 4; i++)
CSR_WRITE_4(sc, BGE_MAR0 + (i * 4), hashes[i]);
return;
}
/*
* Do endian, PCI and DMA initialization. Also check the on-board ROM
* self-test results.
*/
static int
bge_chipinit(sc)
struct bge_softc *sc;
{
int i;
/* Set endianness before we access any non-PCI registers. */
#if BYTE_ORDER == BIG_ENDIAN
pci_write_config(sc->bge_dev, BGE_PCI_MISC_CTL,
BGE_BIGENDIAN_INIT, 4);
#else
pci_write_config(sc->bge_dev, BGE_PCI_MISC_CTL,
BGE_LITTLEENDIAN_INIT, 4);
#endif
/*
* Check the 'ROM failed' bit on the RX CPU to see if
* self-tests passed.
*/
if (CSR_READ_4(sc, BGE_RXCPU_MODE) & BGE_RXCPUMODE_ROMFAIL) {
printf("bge%d: RX CPU self-diagnostics failed!\n",
sc->bge_unit);
return(ENODEV);
}
/* Clear the MAC control register */
CSR_WRITE_4(sc, BGE_MAC_MODE, 0);
/*
* Clear the MAC statistics block in the NIC's
* internal memory.
*/
for (i = BGE_STATS_BLOCK;
i < BGE_STATS_BLOCK_END + 1; i += sizeof(u_int32_t))
BGE_MEMWIN_WRITE(sc, i, 0);
for (i = BGE_STATUS_BLOCK;
i < BGE_STATUS_BLOCK_END + 1; i += sizeof(u_int32_t))
BGE_MEMWIN_WRITE(sc, i, 0);
/* Set up the PCI DMA control register. */
if (pci_read_config(sc->bge_dev, BGE_PCI_PCISTATE, 4) &
BGE_PCISTATE_PCI_BUSMODE) {
/* Conventional PCI bus */
pci_write_config(sc->bge_dev, BGE_PCI_DMA_RW_CTL,
BGE_PCI_READ_CMD|BGE_PCI_WRITE_CMD|0x3F000F, 4);
} else {
/* PCI-X bus */
pci_write_config(sc->bge_dev, BGE_PCI_DMA_RW_CTL,
BGE_PCI_READ_CMD|BGE_PCI_WRITE_CMD|0x1B000F, 4);
}
/*
* Set up general mode register.
*/
CSR_WRITE_4(sc, BGE_MODE_CTL, BGE_MODECTL_WORDSWAP_NONFRAME|
BGE_MODECTL_BYTESWAP_DATA|BGE_MODECTL_WORDSWAP_DATA|
BGE_MODECTL_MAC_ATTN_INTR|BGE_MODECTL_HOST_SEND_BDS|
BGE_MODECTL_NO_RX_CRC|BGE_MODECTL_TX_NO_PHDR_CSUM|
BGE_MODECTL_RX_NO_PHDR_CSUM);
/*
* Disable memory write invalidate. Apparently it is not supported
* properly by these devices.
*/
PCI_CLRBIT(sc->bge_dev, BGE_PCI_CMD, PCIM_CMD_MWIEN, 4);
#ifdef __brokenalpha__
/*
* Must insure that we do not cross an 8K (bytes) boundary
* for DMA reads. Our highest limit is 1K bytes. This is a
* restriction on some ALPHA platforms with early revision
* 21174 PCI chipsets, such as the AlphaPC 164lx
*/
PCI_SETBIT(sc->bge_dev, BGE_PCI_DMA_RW_CTL,
BGE_PCI_READ_BNDRY_1024BYTES, 4);
#endif
/* Set the timer prescaler (always 66Mhz) */
CSR_WRITE_4(sc, BGE_MISC_CFG, 65 << 1/*BGE_32BITTIME_66MHZ*/);
return(0);
}
static int
bge_blockinit(sc)
struct bge_softc *sc;
{
struct bge_rcb *rcb;
volatile struct bge_rcb *vrcb;
int i;
/*
* Initialize the memory window pointer register so that
* we can access the first 32K of internal NIC RAM. This will
* allow us to set up the TX send ring RCBs and the RX return
* ring RCBs, plus other things which live in NIC memory.
*/
CSR_WRITE_4(sc, BGE_PCI_MEMWIN_BASEADDR, 0);
/* Configure mbuf memory pool */
if (sc->bge_extram) {
CSR_WRITE_4(sc, BGE_BMAN_MBUFPOOL_BASEADDR, BGE_EXT_SSRAM);
CSR_WRITE_4(sc, BGE_BMAN_MBUFPOOL_LEN, 0x18000);
} else {
CSR_WRITE_4(sc, BGE_BMAN_MBUFPOOL_BASEADDR, BGE_BUFFPOOL_1);
CSR_WRITE_4(sc, BGE_BMAN_MBUFPOOL_LEN, 0x18000);
}
/* Configure DMA resource pool */
CSR_WRITE_4(sc, BGE_BMAN_DMA_DESCPOOL_BASEADDR, BGE_DMA_DESCRIPTORS);
CSR_WRITE_4(sc, BGE_BMAN_DMA_DESCPOOL_LEN, 0x2000);
/* Configure mbuf pool watermarks */
CSR_WRITE_4(sc, BGE_BMAN_MBUFPOOL_READDMA_LOWAT, 0x50);
CSR_WRITE_4(sc, BGE_BMAN_MBUFPOOL_MACRX_LOWAT, 0x20);
CSR_WRITE_4(sc, BGE_BMAN_MBUFPOOL_HIWAT, 0x60);
/* Configure DMA resource watermarks */
CSR_WRITE_4(sc, BGE_BMAN_DMA_DESCPOOL_LOWAT, 5);
CSR_WRITE_4(sc, BGE_BMAN_DMA_DESCPOOL_HIWAT, 10);
/* Enable buffer manager */
CSR_WRITE_4(sc, BGE_BMAN_MODE,
BGE_BMANMODE_ENABLE|BGE_BMANMODE_LOMBUF_ATTN);
/* Poll for buffer manager start indication */
for (i = 0; i < BGE_TIMEOUT; i++) {
if (CSR_READ_4(sc, BGE_BMAN_MODE) & BGE_BMANMODE_ENABLE)
break;
DELAY(10);
}
if (i == BGE_TIMEOUT) {
printf("bge%d: buffer manager failed to start\n",
sc->bge_unit);
return(ENXIO);
}
/* Enable flow-through queues */
CSR_WRITE_4(sc, BGE_FTQ_RESET, 0xFFFFFFFF);
CSR_WRITE_4(sc, BGE_FTQ_RESET, 0);
/* Wait until queue initialization is complete */
for (i = 0; i < BGE_TIMEOUT; i++) {
if (CSR_READ_4(sc, BGE_FTQ_RESET) == 0)
break;
DELAY(10);
}
if (i == BGE_TIMEOUT) {
printf("bge%d: flow-through queue init failed\n",
sc->bge_unit);
return(ENXIO);
}
/* Initialize the standard RX ring control block */
rcb = &sc->bge_rdata->bge_info.bge_std_rx_rcb;
BGE_HOSTADDR(rcb->bge_hostaddr) =
vtophys(&sc->bge_rdata->bge_rx_std_ring);
rcb->bge_maxlen_flags = BGE_RCB_MAXLEN_FLAGS(BGE_MAX_FRAMELEN, 0);
if (sc->bge_extram)
rcb->bge_nicaddr = BGE_EXT_STD_RX_RINGS;
else
rcb->bge_nicaddr = BGE_STD_RX_RINGS;
CSR_WRITE_4(sc, BGE_RX_STD_RCB_HADDR_HI, rcb->bge_hostaddr.bge_addr_hi);
CSR_WRITE_4(sc, BGE_RX_STD_RCB_HADDR_LO, rcb->bge_hostaddr.bge_addr_lo);
CSR_WRITE_4(sc, BGE_RX_STD_RCB_MAXLEN_FLAGS, rcb->bge_maxlen_flags);
CSR_WRITE_4(sc, BGE_RX_STD_RCB_NICADDR, rcb->bge_nicaddr);
/*
* Initialize the jumbo RX ring control block
* We set the 'ring disabled' bit in the flags
* field until we're actually ready to start
* using this ring (i.e. once we set the MTU
* high enough to require it).
*/
rcb = &sc->bge_rdata->bge_info.bge_jumbo_rx_rcb;
BGE_HOSTADDR(rcb->bge_hostaddr) =
vtophys(&sc->bge_rdata->bge_rx_jumbo_ring);
rcb->bge_maxlen_flags =
BGE_RCB_MAXLEN_FLAGS(BGE_MAX_FRAMELEN, BGE_RCB_FLAG_RING_DISABLED);
if (sc->bge_extram)
rcb->bge_nicaddr = BGE_EXT_JUMBO_RX_RINGS;
else
rcb->bge_nicaddr = BGE_JUMBO_RX_RINGS;
CSR_WRITE_4(sc, BGE_RX_JUMBO_RCB_HADDR_HI,
rcb->bge_hostaddr.bge_addr_hi);
CSR_WRITE_4(sc, BGE_RX_JUMBO_RCB_HADDR_LO,
rcb->bge_hostaddr.bge_addr_lo);
CSR_WRITE_4(sc, BGE_RX_JUMBO_RCB_MAXLEN_FLAGS, rcb->bge_maxlen_flags);
CSR_WRITE_4(sc, BGE_RX_JUMBO_RCB_NICADDR, rcb->bge_nicaddr);
/* Set up dummy disabled mini ring RCB */
rcb = &sc->bge_rdata->bge_info.bge_mini_rx_rcb;
rcb->bge_maxlen_flags =
BGE_RCB_MAXLEN_FLAGS(0, BGE_RCB_FLAG_RING_DISABLED);
CSR_WRITE_4(sc, BGE_RX_MINI_RCB_MAXLEN_FLAGS, rcb->bge_maxlen_flags);
/*
* Set the BD ring replentish thresholds. The recommended
* values are 1/8th the number of descriptors allocated to
* each ring.
*/
CSR_WRITE_4(sc, BGE_RBDI_STD_REPL_THRESH, BGE_STD_RX_RING_CNT/8);
CSR_WRITE_4(sc, BGE_RBDI_JUMBO_REPL_THRESH, BGE_JUMBO_RX_RING_CNT/8);
/*
* Disable all unused send rings by setting the 'ring disabled'
* bit in the flags field of all the TX send ring control blocks.
* These are located in NIC memory.
*/
vrcb = (volatile struct bge_rcb *)(sc->bge_vhandle + BGE_MEMWIN_START +
BGE_SEND_RING_RCB);
for (i = 0; i < BGE_TX_RINGS_EXTSSRAM_MAX; i++) {
vrcb->bge_maxlen_flags =
BGE_RCB_MAXLEN_FLAGS(0, BGE_RCB_FLAG_RING_DISABLED);
vrcb->bge_nicaddr = 0;
vrcb++;
}
/* Configure TX RCB 0 (we use only the first ring) */
vrcb = (volatile struct bge_rcb *)(sc->bge_vhandle + BGE_MEMWIN_START +
BGE_SEND_RING_RCB);
vrcb->bge_hostaddr.bge_addr_hi = 0;
BGE_HOSTADDR(vrcb->bge_hostaddr) =
vtophys(&sc->bge_rdata->bge_tx_ring);
vrcb->bge_nicaddr = BGE_NIC_TXRING_ADDR(0, BGE_TX_RING_CNT);
vrcb->bge_maxlen_flags = BGE_RCB_MAXLEN_FLAGS(BGE_TX_RING_CNT, 0);
/* Disable all unused RX return rings */
vrcb = (volatile struct bge_rcb *)(sc->bge_vhandle + BGE_MEMWIN_START +
BGE_RX_RETURN_RING_RCB);
for (i = 0; i < BGE_RX_RINGS_MAX; i++) {
vrcb->bge_hostaddr.bge_addr_hi = 0;
vrcb->bge_hostaddr.bge_addr_lo = 0;
vrcb->bge_maxlen_flags =
BGE_RCB_MAXLEN_FLAGS(BGE_RETURN_RING_CNT,
BGE_RCB_FLAG_RING_DISABLED);
vrcb->bge_nicaddr = 0;
CSR_WRITE_4(sc, BGE_MBX_RX_CONS0_LO +
(i * (sizeof(u_int64_t))), 0);
vrcb++;
}
/* Initialize RX ring indexes */
CSR_WRITE_4(sc, BGE_MBX_RX_STD_PROD_LO, 0);
CSR_WRITE_4(sc, BGE_MBX_RX_JUMBO_PROD_LO, 0);
CSR_WRITE_4(sc, BGE_MBX_RX_MINI_PROD_LO, 0);
/*
* Set up RX return ring 0
* Note that the NIC address for RX return rings is 0x00000000.
* The return rings live entirely within the host, so the
* nicaddr field in the RCB isn't used.
*/
vrcb = (volatile struct bge_rcb *)(sc->bge_vhandle + BGE_MEMWIN_START +
BGE_RX_RETURN_RING_RCB);
vrcb->bge_hostaddr.bge_addr_hi = 0;
BGE_HOSTADDR(vrcb->bge_hostaddr) =
vtophys(&sc->bge_rdata->bge_rx_return_ring);
vrcb->bge_nicaddr = 0x00000000;
vrcb->bge_maxlen_flags = BGE_RCB_MAXLEN_FLAGS(BGE_RETURN_RING_CNT, 0);
/* Set random backoff seed for TX */
CSR_WRITE_4(sc, BGE_TX_RANDOM_BACKOFF,
sc->arpcom.ac_enaddr[0] + sc->arpcom.ac_enaddr[1] +
sc->arpcom.ac_enaddr[2] + sc->arpcom.ac_enaddr[3] +
sc->arpcom.ac_enaddr[4] + sc->arpcom.ac_enaddr[5] +
BGE_TX_BACKOFF_SEED_MASK);
/* Set inter-packet gap */
CSR_WRITE_4(sc, BGE_TX_LENGTHS, 0x2620);
/*
* Specify which ring to use for packets that don't match
* any RX rules.
*/
CSR_WRITE_4(sc, BGE_RX_RULES_CFG, 0x08);
/*
* Configure number of RX lists. One interrupt distribution
* list, sixteen active lists, one bad frames class.
*/
CSR_WRITE_4(sc, BGE_RXLP_CFG, 0x181);
/* Inialize RX list placement stats mask. */
CSR_WRITE_4(sc, BGE_RXLP_STATS_ENABLE_MASK, 0x007FFFFF);
CSR_WRITE_4(sc, BGE_RXLP_STATS_CTL, 0x1);
/* Disable host coalescing until we get it set up */
CSR_WRITE_4(sc, BGE_HCC_MODE, 0x00000000);
/* Poll to make sure it's shut down. */
for (i = 0; i < BGE_TIMEOUT; i++) {
if (!(CSR_READ_4(sc, BGE_HCC_MODE) & BGE_HCCMODE_ENABLE))
break;
DELAY(10);
}
if (i == BGE_TIMEOUT) {
printf("bge%d: host coalescing engine failed to idle\n",
sc->bge_unit);
return(ENXIO);
}
/* Set up host coalescing defaults */
CSR_WRITE_4(sc, BGE_HCC_RX_COAL_TICKS, sc->bge_rx_coal_ticks);
CSR_WRITE_4(sc, BGE_HCC_TX_COAL_TICKS, sc->bge_tx_coal_ticks);
CSR_WRITE_4(sc, BGE_HCC_RX_MAX_COAL_BDS, sc->bge_rx_max_coal_bds);
CSR_WRITE_4(sc, BGE_HCC_TX_MAX_COAL_BDS, sc->bge_tx_max_coal_bds);
CSR_WRITE_4(sc, BGE_HCC_RX_COAL_TICKS_INT, 0);
CSR_WRITE_4(sc, BGE_HCC_TX_COAL_TICKS_INT, 0);
CSR_WRITE_4(sc, BGE_HCC_RX_MAX_COAL_BDS_INT, 0);
CSR_WRITE_4(sc, BGE_HCC_TX_MAX_COAL_BDS_INT, 0);
CSR_WRITE_4(sc, BGE_HCC_STATS_TICKS, sc->bge_stat_ticks);
/* Set up address of statistics block */
CSR_WRITE_4(sc, BGE_HCC_STATS_BASEADDR, BGE_STATS_BLOCK);
CSR_WRITE_4(sc, BGE_HCC_STATS_ADDR_HI, 0);
CSR_WRITE_4(sc, BGE_HCC_STATS_ADDR_LO,
vtophys(&sc->bge_rdata->bge_info.bge_stats));
/* Set up address of status block */
CSR_WRITE_4(sc, BGE_HCC_STATUSBLK_BASEADDR, BGE_STATUS_BLOCK);
CSR_WRITE_4(sc, BGE_HCC_STATUSBLK_ADDR_HI, 0);
CSR_WRITE_4(sc, BGE_HCC_STATUSBLK_ADDR_LO,
vtophys(&sc->bge_rdata->bge_status_block));
sc->bge_rdata->bge_status_block.bge_idx[0].bge_rx_prod_idx = 0;
sc->bge_rdata->bge_status_block.bge_idx[0].bge_tx_cons_idx = 0;
/* Turn on host coalescing state machine */
CSR_WRITE_4(sc, BGE_HCC_MODE, BGE_HCCMODE_ENABLE);
/* Turn on RX BD completion state machine and enable attentions */
CSR_WRITE_4(sc, BGE_RBDC_MODE,
BGE_RBDCMODE_ENABLE|BGE_RBDCMODE_ATTN);
/* Turn on RX list placement state machine */
CSR_WRITE_4(sc, BGE_RXLP_MODE, BGE_RXLPMODE_ENABLE);
/* Turn on RX list selector state machine. */
CSR_WRITE_4(sc, BGE_RXLS_MODE, BGE_RXLSMODE_ENABLE);
/* Turn on DMA, clear stats */
CSR_WRITE_4(sc, BGE_MAC_MODE, BGE_MACMODE_TXDMA_ENB|
BGE_MACMODE_RXDMA_ENB|BGE_MACMODE_RX_STATS_CLEAR|
BGE_MACMODE_TX_STATS_CLEAR|BGE_MACMODE_RX_STATS_ENB|
BGE_MACMODE_TX_STATS_ENB|BGE_MACMODE_FRMHDR_DMA_ENB|
(sc->bge_tbi ? BGE_PORTMODE_TBI : BGE_PORTMODE_MII));
/* Set misc. local control, enable interrupts on attentions */
CSR_WRITE_4(sc, BGE_MISC_LOCAL_CTL, BGE_MLC_INTR_ONATTN);
#ifdef notdef
/* Assert GPIO pins for PHY reset */
BGE_SETBIT(sc, BGE_MISC_LOCAL_CTL, BGE_MLC_MISCIO_OUT0|
BGE_MLC_MISCIO_OUT1|BGE_MLC_MISCIO_OUT2);
BGE_SETBIT(sc, BGE_MISC_LOCAL_CTL, BGE_MLC_MISCIO_OUTEN0|
BGE_MLC_MISCIO_OUTEN1|BGE_MLC_MISCIO_OUTEN2);
#endif
/* Turn on DMA completion state machine */
CSR_WRITE_4(sc, BGE_DMAC_MODE, BGE_DMACMODE_ENABLE);
/* Turn on write DMA state machine */
CSR_WRITE_4(sc, BGE_WDMA_MODE,
BGE_WDMAMODE_ENABLE|BGE_WDMAMODE_ALL_ATTNS);
/* Turn on read DMA state machine */
CSR_WRITE_4(sc, BGE_RDMA_MODE,
BGE_RDMAMODE_ENABLE|BGE_RDMAMODE_ALL_ATTNS);
/* Turn on RX data completion state machine */
CSR_WRITE_4(sc, BGE_RDC_MODE, BGE_RDCMODE_ENABLE);
/* Turn on RX BD initiator state machine */
CSR_WRITE_4(sc, BGE_RBDI_MODE, BGE_RBDIMODE_ENABLE);
/* Turn on RX data and RX BD initiator state machine */
CSR_WRITE_4(sc, BGE_RDBDI_MODE, BGE_RDBDIMODE_ENABLE);
/* Turn on Mbuf cluster free state machine */
CSR_WRITE_4(sc, BGE_MBCF_MODE, BGE_MBCFMODE_ENABLE);
/* Turn on send BD completion state machine */
CSR_WRITE_4(sc, BGE_SBDC_MODE, BGE_SBDCMODE_ENABLE);
/* Turn on send data completion state machine */
CSR_WRITE_4(sc, BGE_SDC_MODE, BGE_SDCMODE_ENABLE);
/* Turn on send data initiator state machine */
CSR_WRITE_4(sc, BGE_SDI_MODE, BGE_SDIMODE_ENABLE);
/* Turn on send BD initiator state machine */
CSR_WRITE_4(sc, BGE_SBDI_MODE, BGE_SBDIMODE_ENABLE);
/* Turn on send BD selector state machine */
CSR_WRITE_4(sc, BGE_SRS_MODE, BGE_SRSMODE_ENABLE);
CSR_WRITE_4(sc, BGE_SDI_STATS_ENABLE_MASK, 0x007FFFFF);
CSR_WRITE_4(sc, BGE_SDI_STATS_CTL,
BGE_SDISTATSCTL_ENABLE|BGE_SDISTATSCTL_FASTER);
/* init LED register */
CSR_WRITE_4(sc, BGE_MAC_LED_CTL, 0x00000000);
/* ack/clear link change events */
CSR_WRITE_4(sc, BGE_MAC_STS, BGE_MACSTAT_SYNC_CHANGED|
BGE_MACSTAT_CFG_CHANGED);
CSR_WRITE_4(sc, BGE_MI_STS, 0);
/* Enable PHY auto polling (for MII/GMII only) */
if (sc->bge_tbi) {
CSR_WRITE_4(sc, BGE_MI_STS, BGE_MISTS_LINK);
} else {
BGE_SETBIT(sc, BGE_MI_MODE, BGE_MIMODE_AUTOPOLL|10<<16);
if (sc->bge_asicrev == BGE_ASICREV_BCM5700)
CSR_WRITE_4(sc, BGE_MAC_EVT_ENB,
BGE_EVTENB_MI_INTERRUPT);
}
/* Enable link state change attentions. */
BGE_SETBIT(sc, BGE_MAC_EVT_ENB, BGE_EVTENB_LINK_CHANGED);
return(0);
}
/*
* Probe for a Broadcom chip. Check the PCI vendor and device IDs
* against our list and return its name if we find a match. Note
* that since the Broadcom controller contains VPD support, we
* can get the device name string from the controller itself instead
* of the compiled-in string. This is a little slow, but it guarantees
* we'll always announce the right product name.
*/
static int
bge_probe(dev)
device_t dev;
{
struct bge_type *t;
struct bge_softc *sc;
char *descbuf;
t = bge_devs;
sc = device_get_softc(dev);
bzero(sc, sizeof(struct bge_softc));
sc->bge_unit = device_get_unit(dev);
sc->bge_dev = dev;
while(t->bge_name != NULL) {
if ((pci_get_vendor(dev) == t->bge_vid) &&
(pci_get_device(dev) == t->bge_did)) {
#ifdef notdef
bge_vpd_read(sc);
device_set_desc(dev, sc->bge_vpd_prodname);
#endif
descbuf = malloc(BGE_DEVDESC_MAX, M_TEMP, M_NOWAIT);
if (descbuf == NULL)
return(ENOMEM);
snprintf(descbuf, BGE_DEVDESC_MAX,
"%s, ASIC rev. %#04x", t->bge_name,
pci_read_config(dev, BGE_PCI_MISC_CTL, 4) >> 16);
device_set_desc_copy(dev, descbuf);
free(descbuf, M_TEMP);
return(0);
}
t++;
}
return(ENXIO);
}
static int
bge_attach(dev)
device_t dev;
{
int s;
struct ifnet *ifp;
struct bge_softc *sc;
u_int32_t hwcfg = 0;
u_int32_t mac_addr = 0;
int unit, error = 0, rid;
s = splimp();
sc = device_get_softc(dev);
unit = device_get_unit(dev);
sc->bge_dev = dev;
sc->bge_unit = unit;
/*
* Map control/status registers.
*/
pci_enable_busmaster(dev);
rid = BGE_PCI_BAR0;
sc->bge_res = bus_alloc_resource(dev, SYS_RES_MEMORY, &rid,
0, ~0, 1, RF_ACTIVE|PCI_RF_DENSE);
if (sc->bge_res == NULL) {
printf ("bge%d: couldn't map memory\n", unit);
error = ENXIO;
goto fail;
}
sc->bge_btag = rman_get_bustag(sc->bge_res);
sc->bge_bhandle = rman_get_bushandle(sc->bge_res);
sc->bge_vhandle = (vm_offset_t)rman_get_virtual(sc->bge_res);
/* Allocate interrupt */
rid = 0;
sc->bge_irq = bus_alloc_resource(dev, SYS_RES_IRQ, &rid, 0, ~0, 1,
RF_SHAREABLE | RF_ACTIVE);
if (sc->bge_irq == NULL) {
printf("bge%d: couldn't map interrupt\n", unit);
error = ENXIO;
goto fail;
}
error = bus_setup_intr(dev, sc->bge_irq, INTR_TYPE_NET,
bge_intr, sc, &sc->bge_intrhand);
if (error) {
bge_release_resources(sc);
printf("bge%d: couldn't set up irq\n", unit);
goto fail;
}
sc->bge_unit = unit;
/* Try to reset the chip. */
bge_reset(sc);
if (bge_chipinit(sc)) {
printf("bge%d: chip initialization failed\n", sc->bge_unit);
bge_release_resources(sc);
error = ENXIO;
goto fail;
}
/*
* Get station address from the EEPROM.
*/
mac_addr = bge_readmem_ind(sc, 0x0c14);
if ((mac_addr >> 16) == 0x484b) {
sc->arpcom.ac_enaddr[0] = (u_char)(mac_addr >> 8);
sc->arpcom.ac_enaddr[1] = (u_char)mac_addr;
mac_addr = bge_readmem_ind(sc, 0x0c18);
sc->arpcom.ac_enaddr[2] = (u_char)(mac_addr >> 24);
sc->arpcom.ac_enaddr[3] = (u_char)(mac_addr >> 16);
sc->arpcom.ac_enaddr[4] = (u_char)(mac_addr >> 8);
sc->arpcom.ac_enaddr[5] = (u_char)mac_addr;
} else if (bge_read_eeprom(sc, (caddr_t)&sc->arpcom.ac_enaddr,
BGE_EE_MAC_OFFSET + 2, ETHER_ADDR_LEN)) {
printf("bge%d: failed to read station address\n", unit);
bge_release_resources(sc);
error = ENXIO;
goto fail;
}
/*
* A Broadcom chip was detected. Inform the world.
*/
printf("bge%d: Ethernet address: %6D\n", unit,
sc->arpcom.ac_enaddr, ":");
/* Allocate the general information block and ring buffers. */
sc->bge_rdata = contigmalloc(sizeof(struct bge_ring_data), M_DEVBUF,
M_NOWAIT, 0, 0xffffffff, PAGE_SIZE, 0);
if (sc->bge_rdata == NULL) {
bge_release_resources(sc);
error = ENXIO;
printf("bge%d: no memory for list buffers!\n", sc->bge_unit);
goto fail;
}
bzero(sc->bge_rdata, sizeof(struct bge_ring_data));
/* Try to allocate memory for jumbo buffers. */
if (bge_alloc_jumbo_mem(sc)) {
printf("bge%d: jumbo buffer allocation "
"failed\n", sc->bge_unit);
bge_release_resources(sc);
error = ENXIO;
goto fail;
}
/* Set default tuneable values. */
sc->bge_stat_ticks = BGE_TICKS_PER_SEC;
sc->bge_rx_coal_ticks = 150;
sc->bge_tx_coal_ticks = 150;
sc->bge_rx_max_coal_bds = 64;
sc->bge_tx_max_coal_bds = 128;
/* Set up ifnet structure */
ifp = &sc->arpcom.ac_if;
ifp->if_softc = sc;
ifp->if_unit = sc->bge_unit;
ifp->if_name = "bge";
ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_MULTICAST;
ifp->if_ioctl = bge_ioctl;
ifp->if_output = ether_output;
ifp->if_start = bge_start;
ifp->if_watchdog = bge_watchdog;
ifp->if_init = bge_init;
ifp->if_mtu = ETHERMTU;
ifp->if_snd.ifq_maxlen = BGE_TX_RING_CNT - 1;
ifp->if_hwassist = BGE_CSUM_FEATURES;
ifp->if_capabilities = IFCAP_HWCSUM | IFCAP_VLAN_HWTAGGING | IFCAP_VLAN_MTU;
ifp->if_capenable = ifp->if_capabilities;
/* Save ASIC rev. */
sc->bge_asicrev =
pci_read_config(dev, BGE_PCI_MISC_CTL, 4) &
BGE_PCIMISCCTL_ASICREV;
/* Pretend all 5700s are the same */
if ((sc->bge_asicrev & 0xFF000000) == BGE_ASICREV_BCM5700)
sc->bge_asicrev = BGE_ASICREV_BCM5700;
/*
* Figure out what sort of media we have by checking the
* hardware config word in the first 32k of NIC internal memory,
* or fall back to examining the EEPROM if necessary.
* Note: on some BCM5700 cards, this value appears to be unset.
* If that's the case, we have to rely on identifying the NIC
* by its PCI subsystem ID, as we do below for the SysKonnect
* SK-9D41.
*/
if (bge_readmem_ind(sc, BGE_SOFTWARE_GENCOMM_SIG) == BGE_MAGIC_NUMBER)
hwcfg = bge_readmem_ind(sc, BGE_SOFTWARE_GENCOMM_NICCFG);
else {
bge_read_eeprom(sc, (caddr_t)&hwcfg,
BGE_EE_HWCFG_OFFSET, sizeof(hwcfg));
hwcfg = ntohl(hwcfg);
}
if ((hwcfg & BGE_HWCFG_MEDIA) == BGE_MEDIA_FIBER)
sc->bge_tbi = 1;
/* The SysKonnect SK-9D41 is a 1000baseSX card. */
if ((pci_read_config(dev, BGE_PCI_SUBSYS, 4) >> 16) == SK_SUBSYSID_9D41)
sc->bge_tbi = 1;
if (sc->bge_tbi) {
ifmedia_init(&sc->bge_ifmedia, IFM_IMASK,
bge_ifmedia_upd, bge_ifmedia_sts);
ifmedia_add(&sc->bge_ifmedia, IFM_ETHER|IFM_1000_SX, 0, NULL);
ifmedia_add(&sc->bge_ifmedia,
IFM_ETHER|IFM_1000_SX|IFM_FDX, 0, NULL);
ifmedia_add(&sc->bge_ifmedia, IFM_ETHER|IFM_AUTO, 0, NULL);
ifmedia_set(&sc->bge_ifmedia, IFM_ETHER|IFM_AUTO);
} else {
/*
* Do transceiver setup.
*/
if (mii_phy_probe(dev, &sc->bge_miibus,
bge_ifmedia_upd, bge_ifmedia_sts)) {
printf("bge%d: MII without any PHY!\n", sc->bge_unit);
bge_release_resources(sc);
bge_free_jumbo_mem(sc);
error = ENXIO;
goto fail;
}
}
/*
* When using the BCM5701 in PCI-X mode, data corruption has
* been observed in the first few bytes of some received packets.
* Aligning the packet buffer in memory eliminates the corruption.
* Unfortunately, this misaligns the packet payloads. On platforms
* which do not support unaligned accesses, we will realign the
* payloads by copying the received packets.
*/
switch (sc->bge_asicrev) {
case BGE_ASICREV_BCM5701_A0:
case BGE_ASICREV_BCM5701_B0:
case BGE_ASICREV_BCM5701_B2:
case BGE_ASICREV_BCM5701_B5:
/* If in PCI-X mode, work around the alignment bug. */
if ((pci_read_config(dev, BGE_PCI_PCISTATE, 4) &
(BGE_PCISTATE_PCI_BUSMODE | BGE_PCISTATE_PCI_BUSSPEED)) ==
BGE_PCISTATE_PCI_BUSSPEED)
sc->bge_rx_alignment_bug = 1;
break;
}
/*
* Call MI attach routine.
*/
ether_ifattach(ifp, sc->arpcom.ac_enaddr);
callout_handle_init(&sc->bge_stat_ch);
fail:
splx(s);
return(error);
}
static int
bge_detach(dev)
device_t dev;
{
struct bge_softc *sc;
struct ifnet *ifp;
int s;
s = splimp();
sc = device_get_softc(dev);
ifp = &sc->arpcom.ac_if;
ether_ifdetach(ifp);
bge_stop(sc);
bge_reset(sc);
if (sc->bge_tbi) {
ifmedia_removeall(&sc->bge_ifmedia);
} else {
bus_generic_detach(dev);
device_delete_child(dev, sc->bge_miibus);
}
bge_release_resources(sc);
bge_free_jumbo_mem(sc);
splx(s);
return(0);
}
static void
bge_release_resources(sc)
struct bge_softc *sc;
{
device_t dev;
dev = sc->bge_dev;
if (sc->bge_vpd_prodname != NULL)
free(sc->bge_vpd_prodname, M_DEVBUF);
if (sc->bge_vpd_readonly != NULL)
free(sc->bge_vpd_readonly, M_DEVBUF);
if (sc->bge_intrhand != NULL)
bus_teardown_intr(dev, sc->bge_irq, sc->bge_intrhand);
if (sc->bge_irq != NULL)
bus_release_resource(dev, SYS_RES_IRQ, 0, sc->bge_irq);
if (sc->bge_res != NULL)
bus_release_resource(dev, SYS_RES_MEMORY,
BGE_PCI_BAR0, sc->bge_res);
if (sc->bge_rdata != NULL)
contigfree(sc->bge_rdata,
sizeof(struct bge_ring_data), M_DEVBUF);
return;
}
static void
bge_reset(sc)
struct bge_softc *sc;
{
device_t dev;
u_int32_t cachesize, command, pcistate;
int i, val = 0;
dev = sc->bge_dev;
/* Save some important PCI state. */
cachesize = pci_read_config(dev, BGE_PCI_CACHESZ, 4);
command = pci_read_config(dev, BGE_PCI_CMD, 4);
pcistate = pci_read_config(dev, BGE_PCI_PCISTATE, 4);
pci_write_config(dev, BGE_PCI_MISC_CTL,
BGE_PCIMISCCTL_INDIRECT_ACCESS|BGE_PCIMISCCTL_MASK_PCI_INTR|
BGE_PCIMISCCTL_ENDIAN_WORDSWAP|BGE_PCIMISCCTL_PCISTATE_RW, 4);
/* Issue global reset */
bge_writereg_ind(sc, BGE_MISC_CFG,
BGE_MISCCFG_RESET_CORE_CLOCKS|(65<<1));
DELAY(1000);
/* Reset some of the PCI state that got zapped by reset */
pci_write_config(dev, BGE_PCI_MISC_CTL,
BGE_PCIMISCCTL_INDIRECT_ACCESS|BGE_PCIMISCCTL_MASK_PCI_INTR|
BGE_PCIMISCCTL_ENDIAN_WORDSWAP|BGE_PCIMISCCTL_PCISTATE_RW, 4);
pci_write_config(dev, BGE_PCI_CACHESZ, cachesize, 4);
pci_write_config(dev, BGE_PCI_CMD, command, 4);
bge_writereg_ind(sc, BGE_MISC_CFG, (65 << 1));
/*
* Prevent PXE restart: write a magic number to the
* general communications memory at 0xB50.
*/
bge_writemem_ind(sc, BGE_SOFTWARE_GENCOMM, BGE_MAGIC_NUMBER);
/*
* Poll the value location we just wrote until
* we see the 1's complement of the magic number.
* This indicates that the firmware initialization
* is complete.
*/
for (i = 0; i < BGE_TIMEOUT; i++) {
val = bge_readmem_ind(sc, BGE_SOFTWARE_GENCOMM);
if (val == ~BGE_MAGIC_NUMBER)
break;
DELAY(10);
}
if (i == BGE_TIMEOUT) {
printf("bge%d: firmware handshake timed out\n", sc->bge_unit);
return;
}
/*
* XXX Wait for the value of the PCISTATE register to
* return to its original pre-reset state. This is a
* fairly good indicator of reset completion. If we don't
* wait for the reset to fully complete, trying to read
* from the device's non-PCI registers may yield garbage
* results.
*/
for (i = 0; i < BGE_TIMEOUT; i++) {
if (pci_read_config(dev, BGE_PCI_PCISTATE, 4) == pcistate)
break;
DELAY(10);
}
/* Enable memory arbiter. */
CSR_WRITE_4(sc, BGE_MARB_MODE, BGE_MARBMODE_ENABLE);
/* Fix up byte swapping */
CSR_WRITE_4(sc, BGE_MODE_CTL, BGE_MODECTL_BYTESWAP_NONFRAME|
BGE_MODECTL_BYTESWAP_DATA);
CSR_WRITE_4(sc, BGE_MAC_MODE, 0);
DELAY(10000);
return;
}
/*
* Frame reception handling. This is called if there's a frame
* on the receive return list.
*
* Note: we have to be able to handle two possibilities here:
* 1) the frame is from the jumbo recieve ring
* 2) the frame is from the standard receive ring
*/
static void
bge_rxeof(sc)
struct bge_softc *sc;
{
struct ifnet *ifp;
int stdcnt = 0, jumbocnt = 0;
ifp = &sc->arpcom.ac_if;
while(sc->bge_rx_saved_considx !=
sc->bge_rdata->bge_status_block.bge_idx[0].bge_rx_prod_idx) {
struct bge_rx_bd *cur_rx;
u_int32_t rxidx;
struct ether_header *eh;
struct mbuf *m = NULL;
u_int16_t vlan_tag = 0;
int have_tag = 0;
cur_rx =
&sc->bge_rdata->bge_rx_return_ring[sc->bge_rx_saved_considx];
rxidx = cur_rx->bge_idx;
BGE_INC(sc->bge_rx_saved_considx, BGE_RETURN_RING_CNT);
if (cur_rx->bge_flags & BGE_RXBDFLAG_VLAN_TAG) {
have_tag = 1;
vlan_tag = cur_rx->bge_vlan_tag;
}
if (cur_rx->bge_flags & BGE_RXBDFLAG_JUMBO_RING) {
BGE_INC(sc->bge_jumbo, BGE_JUMBO_RX_RING_CNT);
m = sc->bge_cdata.bge_rx_jumbo_chain[rxidx];
sc->bge_cdata.bge_rx_jumbo_chain[rxidx] = NULL;
jumbocnt++;
if (cur_rx->bge_flags & BGE_RXBDFLAG_ERROR) {
ifp->if_ierrors++;
bge_newbuf_jumbo(sc, sc->bge_jumbo, m);
continue;
}
if (bge_newbuf_jumbo(sc,
sc->bge_jumbo, NULL) == ENOBUFS) {
ifp->if_ierrors++;
bge_newbuf_jumbo(sc, sc->bge_jumbo, m);
continue;
}
} else {
BGE_INC(sc->bge_std, BGE_STD_RX_RING_CNT);
m = sc->bge_cdata.bge_rx_std_chain[rxidx];
sc->bge_cdata.bge_rx_std_chain[rxidx] = NULL;
stdcnt++;
if (cur_rx->bge_flags & BGE_RXBDFLAG_ERROR) {
ifp->if_ierrors++;
bge_newbuf_std(sc, sc->bge_std, m);
continue;
}
if (bge_newbuf_std(sc, sc->bge_std,
NULL) == ENOBUFS) {
ifp->if_ierrors++;
bge_newbuf_std(sc, sc->bge_std, m);
continue;
}
}
ifp->if_ipackets++;
#ifndef __i386__
/*
* The i386 allows unaligned accesses, but for other
* platforms we must make sure the payload is aligned.
*/
if (sc->bge_rx_alignment_bug) {
bcopy(m->m_data, m->m_data + ETHER_ALIGN,
cur_rx->bge_len);
m->m_data += ETHER_ALIGN;
}
#endif
eh = mtod(m, struct ether_header *);
m->m_pkthdr.len = m->m_len = cur_rx->bge_len;
m->m_pkthdr.rcvif = ifp;
#if 0 /* currently broken for some packets, possibly related to TCP options */
if (ifp->if_hwassist) {
m->m_pkthdr.csum_flags |= CSUM_IP_CHECKED;
if ((cur_rx->bge_ip_csum ^ 0xffff) == 0)
m->m_pkthdr.csum_flags |= CSUM_IP_VALID;
if (cur_rx->bge_flags & BGE_RXBDFLAG_TCP_UDP_CSUM) {
m->m_pkthdr.csum_data =
cur_rx->bge_tcp_udp_csum;
m->m_pkthdr.csum_flags |= CSUM_DATA_VALID;
}
}
#endif
/*
* If we received a packet with a vlan tag,
* attach that information to the packet.
*/
if (have_tag)
VLAN_INPUT_TAG(ifp, m, vlan_tag, continue);
(*ifp->if_input)(ifp, m);
}
CSR_WRITE_4(sc, BGE_MBX_RX_CONS0_LO, sc->bge_rx_saved_considx);
if (stdcnt)
CSR_WRITE_4(sc, BGE_MBX_RX_STD_PROD_LO, sc->bge_std);
if (jumbocnt)
CSR_WRITE_4(sc, BGE_MBX_RX_JUMBO_PROD_LO, sc->bge_jumbo);
return;
}
static void
bge_txeof(sc)
struct bge_softc *sc;
{
struct bge_tx_bd *cur_tx = NULL;
struct ifnet *ifp;
ifp = &sc->arpcom.ac_if;
/*
* Go through our tx ring and free mbufs for those
* frames that have been sent.
*/
while (sc->bge_tx_saved_considx !=
sc->bge_rdata->bge_status_block.bge_idx[0].bge_tx_cons_idx) {
u_int32_t idx = 0;
idx = sc->bge_tx_saved_considx;
cur_tx = &sc->bge_rdata->bge_tx_ring[idx];
if (cur_tx->bge_flags & BGE_TXBDFLAG_END)
ifp->if_opackets++;
if (sc->bge_cdata.bge_tx_chain[idx] != NULL) {
m_freem(sc->bge_cdata.bge_tx_chain[idx]);
sc->bge_cdata.bge_tx_chain[idx] = NULL;
}
sc->bge_txcnt--;
BGE_INC(sc->bge_tx_saved_considx, BGE_TX_RING_CNT);
ifp->if_timer = 0;
}
if (cur_tx != NULL)
ifp->if_flags &= ~IFF_OACTIVE;
return;
}
static void
bge_intr(xsc)
void *xsc;
{
struct bge_softc *sc;
struct ifnet *ifp;
sc = xsc;
ifp = &sc->arpcom.ac_if;
#ifdef notdef
/* Avoid this for now -- checking this register is expensive. */
/* Make sure this is really our interrupt. */
if (!(CSR_READ_4(sc, BGE_MISC_LOCAL_CTL) & BGE_MLC_INTR_STATE))
return;
#endif
/* Ack interrupt and stop others from occuring. */
CSR_WRITE_4(sc, BGE_MBX_IRQ0_LO, 1);
/*
* Process link state changes.
* Grrr. The link status word in the status block does
* not work correctly on the BCM5700 rev AX and BX chips,
* according to all avaibable information. Hence, we have
* to enable MII interrupts in order to properly obtain
* async link changes. Unfortunately, this also means that
* we have to read the MAC status register to detect link
* changes, thereby adding an additional register access to
* the interrupt handler.
*/
if (sc->bge_asicrev == BGE_ASICREV_BCM5700) {
u_int32_t status;
status = CSR_READ_4(sc, BGE_MAC_STS);
if (status & BGE_MACSTAT_MI_INTERRUPT) {
sc->bge_link = 0;
untimeout(bge_tick, sc, sc->bge_stat_ch);
bge_tick(sc);
/* Clear the interrupt */
CSR_WRITE_4(sc, BGE_MAC_EVT_ENB,
BGE_EVTENB_MI_INTERRUPT);
bge_miibus_readreg(sc->bge_dev, 1, BRGPHY_MII_ISR);
bge_miibus_writereg(sc->bge_dev, 1, BRGPHY_MII_IMR,
BRGPHY_INTRS);
}
} else {
if ((sc->bge_rdata->bge_status_block.bge_status &
BGE_STATFLAG_UPDATED) &&
(sc->bge_rdata->bge_status_block.bge_status &
BGE_STATFLAG_LINKSTATE_CHANGED)) {
sc->bge_rdata->bge_status_block.bge_status &= ~(BGE_STATFLAG_UPDATED|BGE_STATFLAG_LINKSTATE_CHANGED);
sc->bge_link = 0;
untimeout(bge_tick, sc, sc->bge_stat_ch);
bge_tick(sc);
/* Clear the interrupt */
CSR_WRITE_4(sc, BGE_MAC_STS, BGE_MACSTAT_SYNC_CHANGED|
BGE_MACSTAT_CFG_CHANGED);
/* Force flush the status block cached by PCI bridge */
CSR_READ_4(sc, BGE_MBX_IRQ0_LO);
}
}
if (ifp->if_flags & IFF_RUNNING) {
/* Check RX return ring producer/consumer */
bge_rxeof(sc);
/* Check TX ring producer/consumer */
bge_txeof(sc);
}
bge_handle_events(sc);
/* Re-enable interrupts. */
CSR_WRITE_4(sc, BGE_MBX_IRQ0_LO, 0);
if (ifp->if_flags & IFF_RUNNING && ifp->if_snd.ifq_head != NULL)
bge_start(ifp);
return;
}
static void
bge_tick(xsc)
void *xsc;
{
struct bge_softc *sc;
struct mii_data *mii = NULL;
struct ifmedia *ifm = NULL;
struct ifnet *ifp;
int s;
sc = xsc;
ifp = &sc->arpcom.ac_if;
s = splimp();
bge_stats_update(sc);
sc->bge_stat_ch = timeout(bge_tick, sc, hz);
if (sc->bge_link) {
splx(s);
return;
}
if (sc->bge_tbi) {
ifm = &sc->bge_ifmedia;
if (CSR_READ_4(sc, BGE_MAC_STS) &
BGE_MACSTAT_TBI_PCS_SYNCHED) {
sc->bge_link++;
CSR_WRITE_4(sc, BGE_MAC_STS, 0xFFFFFFFF);
printf("bge%d: gigabit link up\n", sc->bge_unit);
if (ifp->if_snd.ifq_head != NULL)
bge_start(ifp);
}
splx(s);
return;
}
mii = device_get_softc(sc->bge_miibus);
mii_tick(mii);
if (!sc->bge_link && mii->mii_media_status & IFM_ACTIVE &&
IFM_SUBTYPE(mii->mii_media_active) != IFM_NONE) {
sc->bge_link++;
if (IFM_SUBTYPE(mii->mii_media_active) == IFM_1000_T ||
IFM_SUBTYPE(mii->mii_media_active) == IFM_1000_SX)
printf("bge%d: gigabit link up\n",
sc->bge_unit);
if (ifp->if_snd.ifq_head != NULL)
bge_start(ifp);
}
splx(s);
return;
}
static void
bge_stats_update(sc)
struct bge_softc *sc;
{
struct ifnet *ifp;
struct bge_stats *stats;
ifp = &sc->arpcom.ac_if;
stats = (struct bge_stats *)(sc->bge_vhandle +
BGE_MEMWIN_START + BGE_STATS_BLOCK);
ifp->if_collisions +=
(stats->dot3StatsSingleCollisionFrames.bge_addr_lo +
stats->dot3StatsMultipleCollisionFrames.bge_addr_lo +
stats->dot3StatsExcessiveCollisions.bge_addr_lo +
stats->dot3StatsLateCollisions.bge_addr_lo) -
ifp->if_collisions;
#ifdef notdef
ifp->if_collisions +=
(sc->bge_rdata->bge_info.bge_stats.dot3StatsSingleCollisionFrames +
sc->bge_rdata->bge_info.bge_stats.dot3StatsMultipleCollisionFrames +
sc->bge_rdata->bge_info.bge_stats.dot3StatsExcessiveCollisions +
sc->bge_rdata->bge_info.bge_stats.dot3StatsLateCollisions) -
ifp->if_collisions;
#endif
return;
}
/*
* Encapsulate an mbuf chain in the tx ring by coupling the mbuf data
* pointers to descriptors.
*/
static int
bge_encap(sc, m_head, txidx)
struct bge_softc *sc;
struct mbuf *m_head;
u_int32_t *txidx;
{
struct bge_tx_bd *f = NULL;
struct mbuf *m;
u_int32_t frag, cur, cnt = 0;
u_int16_t csum_flags = 0;
struct m_tag *mtag;
m = m_head;
cur = frag = *txidx;
if (m_head->m_pkthdr.csum_flags) {
if (m_head->m_pkthdr.csum_flags & CSUM_IP)
csum_flags |= BGE_TXBDFLAG_IP_CSUM;
if (m_head->m_pkthdr.csum_flags & (CSUM_TCP | CSUM_UDP))
csum_flags |= BGE_TXBDFLAG_TCP_UDP_CSUM;
if (m_head->m_flags & M_LASTFRAG)
csum_flags |= BGE_TXBDFLAG_IP_FRAG_END;
else if (m_head->m_flags & M_FRAG)
csum_flags |= BGE_TXBDFLAG_IP_FRAG;
}
mtag = VLAN_OUTPUT_TAG(&sc->arpcom.ac_if, m);
/*
* Start packing the mbufs in this chain into
* the fragment pointers. Stop when we run out
* of fragments or hit the end of the mbuf chain.
*/
for (m = m_head; m != NULL; m = m->m_next) {
if (m->m_len != 0) {
f = &sc->bge_rdata->bge_tx_ring[frag];
if (sc->bge_cdata.bge_tx_chain[frag] != NULL)
break;
BGE_HOSTADDR(f->bge_addr) =
vtophys(mtod(m, vm_offset_t));
f->bge_len = m->m_len;
f->bge_flags = csum_flags;
if (mtag != NULL) {
f->bge_flags |= BGE_TXBDFLAG_VLAN_TAG;
f->bge_vlan_tag = VLAN_TAG_VALUE(mtag);
} else {
f->bge_vlan_tag = 0;
}
/*
* Sanity check: avoid coming within 16 descriptors
* of the end of the ring.
*/
if ((BGE_TX_RING_CNT - (sc->bge_txcnt + cnt)) < 16)
return(ENOBUFS);
cur = frag;
BGE_INC(frag, BGE_TX_RING_CNT);
cnt++;
}
}
if (m != NULL)
return(ENOBUFS);
if (frag == sc->bge_tx_saved_considx)
return(ENOBUFS);
sc->bge_rdata->bge_tx_ring[cur].bge_flags |= BGE_TXBDFLAG_END;
sc->bge_cdata.bge_tx_chain[cur] = m_head;
sc->bge_txcnt += cnt;
*txidx = frag;
return(0);
}
/*
* Main transmit routine. To avoid having to do mbuf copies, we put pointers
* to the mbuf data regions directly in the transmit descriptors.
*/
static void
bge_start(ifp)
struct ifnet *ifp;
{
struct bge_softc *sc;
struct mbuf *m_head = NULL;
u_int32_t prodidx = 0;
sc = ifp->if_softc;
if (!sc->bge_link && ifp->if_snd.ifq_len < 10)
return;
prodidx = CSR_READ_4(sc, BGE_MBX_TX_HOST_PROD0_LO);
while(sc->bge_cdata.bge_tx_chain[prodidx] == NULL) {
IF_DEQUEUE(&ifp->if_snd, m_head);
if (m_head == NULL)
break;
/*
* XXX
* safety overkill. If this is a fragmented packet chain
* with delayed TCP/UDP checksums, then only encapsulate
* it if we have enough descriptors to handle the entire
* chain at once.
* (paranoia -- may not actually be needed)
*/
if (m_head->m_flags & M_FIRSTFRAG &&
m_head->m_pkthdr.csum_flags & (CSUM_DELAY_DATA)) {
if ((BGE_TX_RING_CNT - sc->bge_txcnt) <
m_head->m_pkthdr.csum_data + 16) {
IF_PREPEND(&ifp->if_snd, m_head);
ifp->if_flags |= IFF_OACTIVE;
break;
}
}
/*
* Pack the data into the transmit ring. If we
* don't have room, set the OACTIVE flag and wait
* for the NIC to drain the ring.
*/
if (bge_encap(sc, m_head, &prodidx)) {
IF_PREPEND(&ifp->if_snd, m_head);
ifp->if_flags |= IFF_OACTIVE;
break;
}
/*
* If there's a BPF listener, bounce a copy of this frame
* to him.
*/
BPF_MTAP(ifp, m_head);
}
/* Transmit */
CSR_WRITE_4(sc, BGE_MBX_TX_HOST_PROD0_LO, prodidx);
/*
* Set a timeout in case the chip goes out to lunch.
*/
ifp->if_timer = 5;
return;
}
static void
bge_init(xsc)
void *xsc;
{
struct bge_softc *sc = xsc;
struct ifnet *ifp;
u_int16_t *m;
int s;
s = splimp();
ifp = &sc->arpcom.ac_if;
if (ifp->if_flags & IFF_RUNNING) {
splx(s);
return;
}
/* Cancel pending I/O and flush buffers. */
bge_stop(sc);
bge_reset(sc);
bge_chipinit(sc);
/*
* Init the various state machines, ring
* control blocks and firmware.
*/
if (bge_blockinit(sc)) {
printf("bge%d: initialization failure\n", sc->bge_unit);
splx(s);
return;
}
ifp = &sc->arpcom.ac_if;
/* Specify MTU. */
CSR_WRITE_4(sc, BGE_RX_MTU, ifp->if_mtu +
ETHER_HDR_LEN + ETHER_CRC_LEN);
/* Load our MAC address. */
m = (u_int16_t *)&sc->arpcom.ac_enaddr[0];
CSR_WRITE_4(sc, BGE_MAC_ADDR1_LO, htons(m[0]));
CSR_WRITE_4(sc, BGE_MAC_ADDR1_HI, (htons(m[1]) << 16) | htons(m[2]));
/* Enable or disable promiscuous mode as needed. */
if (ifp->if_flags & IFF_PROMISC) {
BGE_SETBIT(sc, BGE_RX_MODE, BGE_RXMODE_RX_PROMISC);
} else {
BGE_CLRBIT(sc, BGE_RX_MODE, BGE_RXMODE_RX_PROMISC);
}
/* Program multicast filter. */
bge_setmulti(sc);
/* Init RX ring. */
bge_init_rx_ring_std(sc);
/* Init jumbo RX ring. */
if (ifp->if_mtu > (ETHERMTU + ETHER_HDR_LEN + ETHER_CRC_LEN))
bge_init_rx_ring_jumbo(sc);
/* Init our RX return ring index */
sc->bge_rx_saved_considx = 0;
/* Init TX ring. */
bge_init_tx_ring(sc);
/* Turn on transmitter */
BGE_SETBIT(sc, BGE_TX_MODE, BGE_TXMODE_ENABLE);
/* Turn on receiver */
BGE_SETBIT(sc, BGE_RX_MODE, BGE_RXMODE_ENABLE);
/* Tell firmware we're alive. */
BGE_SETBIT(sc, BGE_MODE_CTL, BGE_MODECTL_STACKUP);
/* Enable host interrupts. */
BGE_SETBIT(sc, BGE_PCI_MISC_CTL, BGE_PCIMISCCTL_CLEAR_INTA);
BGE_CLRBIT(sc, BGE_PCI_MISC_CTL, BGE_PCIMISCCTL_MASK_PCI_INTR);
CSR_WRITE_4(sc, BGE_MBX_IRQ0_LO, 0);
bge_ifmedia_upd(ifp);
ifp->if_flags |= IFF_RUNNING;
ifp->if_flags &= ~IFF_OACTIVE;
splx(s);
sc->bge_stat_ch = timeout(bge_tick, sc, hz);
return;
}
/*
* Set media options.
*/
static int
bge_ifmedia_upd(ifp)
struct ifnet *ifp;
{
struct bge_softc *sc;
struct mii_data *mii;
struct ifmedia *ifm;
sc = ifp->if_softc;
ifm = &sc->bge_ifmedia;
/* If this is a 1000baseX NIC, enable the TBI port. */
if (sc->bge_tbi) {
if (IFM_TYPE(ifm->ifm_media) != IFM_ETHER)
return(EINVAL);
switch(IFM_SUBTYPE(ifm->ifm_media)) {
case IFM_AUTO:
break;
case IFM_1000_SX:
if ((ifm->ifm_media & IFM_GMASK) == IFM_FDX) {
BGE_CLRBIT(sc, BGE_MAC_MODE,
BGE_MACMODE_HALF_DUPLEX);
} else {
BGE_SETBIT(sc, BGE_MAC_MODE,
BGE_MACMODE_HALF_DUPLEX);
}
break;
default:
return(EINVAL);
}
return(0);
}
mii = device_get_softc(sc->bge_miibus);
sc->bge_link = 0;
if (mii->mii_instance) {
struct mii_softc *miisc;
for (miisc = LIST_FIRST(&mii->mii_phys); miisc != NULL;
miisc = LIST_NEXT(miisc, mii_list))
mii_phy_reset(miisc);
}
mii_mediachg(mii);
return(0);
}
/*
* Report current media status.
*/
static void
bge_ifmedia_sts(ifp, ifmr)
struct ifnet *ifp;
struct ifmediareq *ifmr;
{
struct bge_softc *sc;
struct mii_data *mii;
sc = ifp->if_softc;
if (sc->bge_tbi) {
ifmr->ifm_status = IFM_AVALID;
ifmr->ifm_active = IFM_ETHER;
if (CSR_READ_4(sc, BGE_MAC_STS) &
BGE_MACSTAT_TBI_PCS_SYNCHED)
ifmr->ifm_status |= IFM_ACTIVE;
ifmr->ifm_active |= IFM_1000_SX;
if (CSR_READ_4(sc, BGE_MAC_MODE) & BGE_MACMODE_HALF_DUPLEX)
ifmr->ifm_active |= IFM_HDX;
else
ifmr->ifm_active |= IFM_FDX;
return;
}
mii = device_get_softc(sc->bge_miibus);
mii_pollstat(mii);
ifmr->ifm_active = mii->mii_media_active;
ifmr->ifm_status = mii->mii_media_status;
return;
}
static int
bge_ioctl(ifp, command, data)
struct ifnet *ifp;
u_long command;
caddr_t data;
{
struct bge_softc *sc = ifp->if_softc;
struct ifreq *ifr = (struct ifreq *) data;
int s, mask, error = 0;
struct mii_data *mii;
s = splimp();
switch(command) {
case SIOCSIFMTU:
if (ifr->ifr_mtu > BGE_JUMBO_MTU)
error = EINVAL;
else {
ifp->if_mtu = ifr->ifr_mtu;
ifp->if_flags &= ~IFF_RUNNING;
bge_init(sc);
}
break;
case SIOCSIFFLAGS:
if (ifp->if_flags & IFF_UP) {
/*
* If only the state of the PROMISC flag changed,
* then just use the 'set promisc mode' command
* instead of reinitializing the entire NIC. Doing
* a full re-init means reloading the firmware and
* waiting for it to start up, which may take a
* second or two.
*/
if (ifp->if_flags & IFF_RUNNING &&
ifp->if_flags & IFF_PROMISC &&
!(sc->bge_if_flags & IFF_PROMISC)) {
BGE_SETBIT(sc, BGE_RX_MODE,
BGE_RXMODE_RX_PROMISC);
} else if (ifp->if_flags & IFF_RUNNING &&
!(ifp->if_flags & IFF_PROMISC) &&
sc->bge_if_flags & IFF_PROMISC) {
BGE_CLRBIT(sc, BGE_RX_MODE,
BGE_RXMODE_RX_PROMISC);
} else
bge_init(sc);
} else {
if (ifp->if_flags & IFF_RUNNING) {
bge_stop(sc);
}
}
sc->bge_if_flags = ifp->if_flags;
error = 0;
break;
case SIOCADDMULTI:
case SIOCDELMULTI:
if (ifp->if_flags & IFF_RUNNING) {
bge_setmulti(sc);
error = 0;
}
break;
case SIOCSIFMEDIA:
case SIOCGIFMEDIA:
if (sc->bge_tbi) {
error = ifmedia_ioctl(ifp, ifr,
&sc->bge_ifmedia, command);
} else {
mii = device_get_softc(sc->bge_miibus);
error = ifmedia_ioctl(ifp, ifr,
&mii->mii_media, command);
}
break;
case SIOCSIFCAP:
mask = ifr->ifr_reqcap ^ ifp->if_capenable;
if (mask & IFCAP_HWCSUM) {
if (IFCAP_HWCSUM & ifp->if_capenable)
ifp->if_capenable &= ~IFCAP_HWCSUM;
else
ifp->if_capenable |= IFCAP_HWCSUM;
}
error = 0;
break;
default:
error = ether_ioctl(ifp, command, data);
break;
}
(void)splx(s);
return(error);
}
static void
bge_watchdog(ifp)
struct ifnet *ifp;
{
struct bge_softc *sc;
sc = ifp->if_softc;
printf("bge%d: watchdog timeout -- resetting\n", sc->bge_unit);
ifp->if_flags &= ~IFF_RUNNING;
bge_init(sc);
ifp->if_oerrors++;
return;
}
/*
* Stop the adapter and free any mbufs allocated to the
* RX and TX lists.
*/
static void
bge_stop(sc)
struct bge_softc *sc;
{
struct ifnet *ifp;
struct ifmedia_entry *ifm;
struct mii_data *mii = NULL;
int mtmp, itmp;
ifp = &sc->arpcom.ac_if;
if (!sc->bge_tbi)
mii = device_get_softc(sc->bge_miibus);
untimeout(bge_tick, sc, sc->bge_stat_ch);
/*
* Disable all of the receiver blocks
*/
BGE_CLRBIT(sc, BGE_RX_MODE, BGE_RXMODE_ENABLE);
BGE_CLRBIT(sc, BGE_RBDI_MODE, BGE_RBDIMODE_ENABLE);
BGE_CLRBIT(sc, BGE_RXLP_MODE, BGE_RXLPMODE_ENABLE);
BGE_CLRBIT(sc, BGE_RXLS_MODE, BGE_RXLSMODE_ENABLE);
BGE_CLRBIT(sc, BGE_RDBDI_MODE, BGE_RBDIMODE_ENABLE);
BGE_CLRBIT(sc, BGE_RDC_MODE, BGE_RDCMODE_ENABLE);
BGE_CLRBIT(sc, BGE_RBDC_MODE, BGE_RBDCMODE_ENABLE);
/*
* Disable all of the transmit blocks
*/
BGE_CLRBIT(sc, BGE_SRS_MODE, BGE_SRSMODE_ENABLE);
BGE_CLRBIT(sc, BGE_SBDI_MODE, BGE_SBDIMODE_ENABLE);
BGE_CLRBIT(sc, BGE_SDI_MODE, BGE_SDIMODE_ENABLE);
BGE_CLRBIT(sc, BGE_RDMA_MODE, BGE_RDMAMODE_ENABLE);
BGE_CLRBIT(sc, BGE_SDC_MODE, BGE_SDCMODE_ENABLE);
BGE_CLRBIT(sc, BGE_DMAC_MODE, BGE_DMACMODE_ENABLE);
BGE_CLRBIT(sc, BGE_SBDC_MODE, BGE_SBDCMODE_ENABLE);
/*
* Shut down all of the memory managers and related
* state machines.
*/
BGE_CLRBIT(sc, BGE_HCC_MODE, BGE_HCCMODE_ENABLE);
BGE_CLRBIT(sc, BGE_WDMA_MODE, BGE_WDMAMODE_ENABLE);
BGE_CLRBIT(sc, BGE_MBCF_MODE, BGE_MBCFMODE_ENABLE);
CSR_WRITE_4(sc, BGE_FTQ_RESET, 0xFFFFFFFF);
CSR_WRITE_4(sc, BGE_FTQ_RESET, 0);
BGE_CLRBIT(sc, BGE_BMAN_MODE, BGE_BMANMODE_ENABLE);
BGE_CLRBIT(sc, BGE_MARB_MODE, BGE_MARBMODE_ENABLE);
/* Disable host interrupts. */
BGE_SETBIT(sc, BGE_PCI_MISC_CTL, BGE_PCIMISCCTL_MASK_PCI_INTR);
CSR_WRITE_4(sc, BGE_MBX_IRQ0_LO, 1);
/*
* Tell firmware we're shutting down.
*/
BGE_CLRBIT(sc, BGE_MODE_CTL, BGE_MODECTL_STACKUP);
/* Free the RX lists. */
bge_free_rx_ring_std(sc);
/* Free jumbo RX list. */
bge_free_rx_ring_jumbo(sc);
/* Free TX buffers. */
bge_free_tx_ring(sc);
/*
* Isolate/power down the PHY, but leave the media selection
* unchanged so that things will be put back to normal when
* we bring the interface back up.
*/
if (!sc->bge_tbi) {
itmp = ifp->if_flags;
ifp->if_flags |= IFF_UP;
ifm = mii->mii_media.ifm_cur;
mtmp = ifm->ifm_media;
ifm->ifm_media = IFM_ETHER|IFM_NONE;
mii_mediachg(mii);
ifm->ifm_media = mtmp;
ifp->if_flags = itmp;
}
sc->bge_link = 0;
sc->bge_tx_saved_considx = BGE_TXCONS_UNSET;
ifp->if_flags &= ~(IFF_RUNNING | IFF_OACTIVE);
return;
}
/*
* Stop all chip I/O so that the kernel's probe routines don't
* get confused by errant DMAs when rebooting.
*/
static void
bge_shutdown(dev)
device_t dev;
{
struct bge_softc *sc;
sc = device_get_softc(dev);
bge_stop(sc);
bge_reset(sc);
return;
}
Reference in New Issue View Git Blame Copy Permalink