537b66a9dd
The vnode-backed md(4) has to map the unmapped bio because VOP_READ() and VOP_WRITE() interfaces do not allow to pass unmapped requests to the filesystem. Vnode-backed md(4) uses pbufs instead of relying on the bio_transient_map, to avoid usual md deadlock. Sponsored by: The FreeBSD Foundation Tested by: pho, scottl
2549 lines
63 KiB
C
2549 lines
63 KiB
C
/*-
|
|
* Largely written by Julian Elischer (julian@tfs.com)
|
|
* for TRW Financial Systems.
|
|
*
|
|
* TRW Financial Systems, in accordance with their agreement with Carnegie
|
|
* Mellon University, makes this software available to CMU to distribute
|
|
* or use in any manner that they see fit as long as this message is kept with
|
|
* the software. For this reason TFS also grants any other persons or
|
|
* organisations permission to use or modify this software.
|
|
*
|
|
* TFS supplies this software to be publicly redistributed
|
|
* on the understanding that TFS is not responsible for the correct
|
|
* functioning of this software in any circumstances.
|
|
*
|
|
* Ported to run under 386BSD by Julian Elischer (julian@tfs.com) Sept 1992
|
|
*
|
|
* $FreeBSD$
|
|
*/
|
|
|
|
/*
|
|
* SCSI general interface description
|
|
*/
|
|
|
|
#ifndef _SCSI_SCSI_ALL_H
|
|
#define _SCSI_SCSI_ALL_H 1
|
|
|
|
#include <sys/cdefs.h>
|
|
#include <machine/stdarg.h>
|
|
|
|
#ifdef _KERNEL
|
|
/*
|
|
* This is the number of seconds we wait for devices to settle after a SCSI
|
|
* bus reset.
|
|
*/
|
|
extern int scsi_delay;
|
|
#endif /* _KERNEL */
|
|
|
|
/*
|
|
* SCSI command format
|
|
*/
|
|
|
|
/*
|
|
* Define dome bits that are in ALL (or a lot of) scsi commands
|
|
*/
|
|
#define SCSI_CTL_LINK 0x01
|
|
#define SCSI_CTL_FLAG 0x02
|
|
#define SCSI_CTL_VENDOR 0xC0
|
|
#define SCSI_CMD_LUN 0xA0 /* these two should not be needed */
|
|
#define SCSI_CMD_LUN_SHIFT 5 /* LUN in the cmd is no longer SCSI */
|
|
|
|
#define SCSI_MAX_CDBLEN 16 /*
|
|
* 16 byte commands are in the
|
|
* SCSI-3 spec
|
|
*/
|
|
#if defined(CAM_MAX_CDBLEN) && (CAM_MAX_CDBLEN < SCSI_MAX_CDBLEN)
|
|
#error "CAM_MAX_CDBLEN cannot be less than SCSI_MAX_CDBLEN"
|
|
#endif
|
|
|
|
/* 6byte CDBs special case 0 length to be 256 */
|
|
#define SCSI_CDB6_LEN(len) ((len) == 0 ? 256 : len)
|
|
|
|
/*
|
|
* This type defines actions to be taken when a particular sense code is
|
|
* received. Right now, these flags are only defined to take up 16 bits,
|
|
* but can be expanded in the future if necessary.
|
|
*/
|
|
typedef enum {
|
|
SS_NOP = 0x000000, /* Do nothing */
|
|
SS_RETRY = 0x010000, /* Retry the command */
|
|
SS_FAIL = 0x020000, /* Bail out */
|
|
SS_START = 0x030000, /* Send a Start Unit command to the device,
|
|
* then retry the original command.
|
|
*/
|
|
SS_TUR = 0x040000, /* Send a Test Unit Ready command to the
|
|
* device, then retry the original command.
|
|
*/
|
|
SS_MASK = 0xff0000
|
|
} scsi_sense_action;
|
|
|
|
typedef enum {
|
|
SSQ_NONE = 0x0000,
|
|
SSQ_DECREMENT_COUNT = 0x0100, /* Decrement the retry count */
|
|
SSQ_MANY = 0x0200, /* send lots of recovery commands */
|
|
SSQ_RANGE = 0x0400, /*
|
|
* This table entry represents the
|
|
* end of a range of ASCQs that
|
|
* have identical error actions
|
|
* and text.
|
|
*/
|
|
SSQ_PRINT_SENSE = 0x0800,
|
|
SSQ_MASK = 0xff00
|
|
} scsi_sense_action_qualifier;
|
|
|
|
/* Mask for error status values */
|
|
#define SS_ERRMASK 0xff
|
|
|
|
/* The default, retyable, error action */
|
|
#define SS_RDEF SS_RETRY|SSQ_DECREMENT_COUNT|SSQ_PRINT_SENSE|EIO
|
|
|
|
/* The retyable, error action, with table specified error code */
|
|
#define SS_RET SS_RETRY|SSQ_DECREMENT_COUNT|SSQ_PRINT_SENSE
|
|
|
|
/* Fatal error action, with table specified error code */
|
|
#define SS_FATAL SS_FAIL|SSQ_PRINT_SENSE
|
|
|
|
struct scsi_generic
|
|
{
|
|
u_int8_t opcode;
|
|
u_int8_t bytes[11];
|
|
};
|
|
|
|
struct scsi_request_sense
|
|
{
|
|
u_int8_t opcode;
|
|
u_int8_t byte2;
|
|
#define SRS_DESC 0x01
|
|
u_int8_t unused[2];
|
|
u_int8_t length;
|
|
u_int8_t control;
|
|
};
|
|
|
|
struct scsi_test_unit_ready
|
|
{
|
|
u_int8_t opcode;
|
|
u_int8_t byte2;
|
|
u_int8_t unused[3];
|
|
u_int8_t control;
|
|
};
|
|
|
|
struct scsi_receive_diag {
|
|
uint8_t opcode;
|
|
uint8_t byte2;
|
|
#define SRD_PCV 0x01
|
|
uint8_t page_code;
|
|
uint8_t length[2];
|
|
uint8_t control;
|
|
};
|
|
|
|
struct scsi_send_diag {
|
|
uint8_t opcode;
|
|
uint8_t byte2;
|
|
#define SSD_UNITOFFL 0x01
|
|
#define SSD_DEVOFFL 0x02
|
|
#define SSD_SELFTEST 0x04
|
|
#define SSD_PF 0x10
|
|
#define SSD_SELF_TEST_CODE_MASK 0xE0
|
|
#define SSD_SELF_TEST_CODE_SHIFT 5
|
|
#define SSD_SELF_TEST_CODE_NONE 0x00
|
|
#define SSD_SELF_TEST_CODE_BG_SHORT 0x01
|
|
#define SSD_SELF_TEST_CODE_BG_EXTENDED 0x02
|
|
#define SSD_SELF_TEST_CODE_BG_ABORT 0x04
|
|
#define SSD_SELF_TEST_CODE_FG_SHORT 0x05
|
|
#define SSD_SELF_TEST_CODE_FG_EXTENDED 0x06
|
|
uint8_t reserved;
|
|
uint8_t length[2];
|
|
uint8_t control;
|
|
};
|
|
|
|
struct scsi_sense
|
|
{
|
|
u_int8_t opcode;
|
|
u_int8_t byte2;
|
|
u_int8_t unused[2];
|
|
u_int8_t length;
|
|
u_int8_t control;
|
|
};
|
|
|
|
struct scsi_inquiry
|
|
{
|
|
u_int8_t opcode;
|
|
u_int8_t byte2;
|
|
#define SI_EVPD 0x01
|
|
#define SI_CMDDT 0x02
|
|
u_int8_t page_code;
|
|
u_int8_t length[2];
|
|
u_int8_t control;
|
|
};
|
|
|
|
struct scsi_mode_sense_6
|
|
{
|
|
u_int8_t opcode;
|
|
u_int8_t byte2;
|
|
#define SMS_DBD 0x08
|
|
u_int8_t page;
|
|
#define SMS_PAGE_CODE 0x3F
|
|
#define SMS_VENDOR_SPECIFIC_PAGE 0x00
|
|
#define SMS_DISCONNECT_RECONNECT_PAGE 0x02
|
|
#define SMS_FORMAT_DEVICE_PAGE 0x03
|
|
#define SMS_GEOMETRY_PAGE 0x04
|
|
#define SMS_CACHE_PAGE 0x08
|
|
#define SMS_PERIPHERAL_DEVICE_PAGE 0x09
|
|
#define SMS_CONTROL_MODE_PAGE 0x0A
|
|
#define SMS_PROTO_SPECIFIC_PAGE 0x19
|
|
#define SMS_INFO_EXCEPTIONS_PAGE 0x1C
|
|
#define SMS_ALL_PAGES_PAGE 0x3F
|
|
#define SMS_PAGE_CTRL_MASK 0xC0
|
|
#define SMS_PAGE_CTRL_CURRENT 0x00
|
|
#define SMS_PAGE_CTRL_CHANGEABLE 0x40
|
|
#define SMS_PAGE_CTRL_DEFAULT 0x80
|
|
#define SMS_PAGE_CTRL_SAVED 0xC0
|
|
u_int8_t subpage;
|
|
#define SMS_SUBPAGE_PAGE_0 0x00
|
|
#define SMS_SUBPAGE_ALL 0xff
|
|
u_int8_t length;
|
|
u_int8_t control;
|
|
};
|
|
|
|
struct scsi_mode_sense_10
|
|
{
|
|
u_int8_t opcode;
|
|
u_int8_t byte2; /* same bits as small version */
|
|
#define SMS10_LLBAA 0x10
|
|
u_int8_t page; /* same bits as small version */
|
|
u_int8_t subpage;
|
|
u_int8_t unused[3];
|
|
u_int8_t length[2];
|
|
u_int8_t control;
|
|
};
|
|
|
|
struct scsi_mode_select_6
|
|
{
|
|
u_int8_t opcode;
|
|
u_int8_t byte2;
|
|
#define SMS_SP 0x01
|
|
#define SMS_PF 0x10
|
|
u_int8_t unused[2];
|
|
u_int8_t length;
|
|
u_int8_t control;
|
|
};
|
|
|
|
struct scsi_mode_select_10
|
|
{
|
|
u_int8_t opcode;
|
|
u_int8_t byte2; /* same bits as small version */
|
|
u_int8_t unused[5];
|
|
u_int8_t length[2];
|
|
u_int8_t control;
|
|
};
|
|
|
|
/*
|
|
* When sending a mode select to a tape drive, the medium type must be 0.
|
|
*/
|
|
struct scsi_mode_hdr_6
|
|
{
|
|
u_int8_t datalen;
|
|
u_int8_t medium_type;
|
|
u_int8_t dev_specific;
|
|
u_int8_t block_descr_len;
|
|
};
|
|
|
|
struct scsi_mode_hdr_10
|
|
{
|
|
u_int8_t datalen[2];
|
|
u_int8_t medium_type;
|
|
u_int8_t dev_specific;
|
|
u_int8_t reserved[2];
|
|
u_int8_t block_descr_len[2];
|
|
};
|
|
|
|
struct scsi_mode_block_descr
|
|
{
|
|
u_int8_t density_code;
|
|
u_int8_t num_blocks[3];
|
|
u_int8_t reserved;
|
|
u_int8_t block_len[3];
|
|
};
|
|
|
|
struct scsi_per_res_in
|
|
{
|
|
u_int8_t opcode;
|
|
u_int8_t action;
|
|
#define SPRI_RK 0x00
|
|
#define SPRI_RR 0x01
|
|
#define SPRI_RC 0x02
|
|
#define SPRI_RS 0x03
|
|
u_int8_t reserved[5];
|
|
u_int8_t length[2];
|
|
u_int8_t control;
|
|
};
|
|
|
|
struct scsi_per_res_in_header
|
|
{
|
|
u_int8_t generation[4];
|
|
u_int8_t length[4];
|
|
};
|
|
|
|
struct scsi_per_res_key
|
|
{
|
|
u_int8_t key[8];
|
|
};
|
|
|
|
struct scsi_per_res_in_keys
|
|
{
|
|
struct scsi_per_res_in_header header;
|
|
struct scsi_per_res_key keys[0];
|
|
};
|
|
|
|
struct scsi_per_res_cap
|
|
{
|
|
uint8_t length[2];
|
|
uint8_t flags1;
|
|
#define SPRI_CRH 0x10
|
|
#define SPRI_SIP_C 0x08
|
|
#define SPRI_ATP_C 0x04
|
|
#define SPRI_PTPL_C 0x01
|
|
uint8_t flags2;
|
|
#define SPRI_TMV 0x80
|
|
#define SPRI_PTPL_A 0x01
|
|
uint8_t type_mask[2];
|
|
#define SPRI_TM_WR_EX_AR 0x8000
|
|
#define SPRI_TM_EX_AC_RO 0x4000
|
|
#define SPRI_TM_WR_EX_RO 0x2000
|
|
#define SPRI_TM_EX_AC 0x0800
|
|
#define SPRI_TM_WR_EX 0x0200
|
|
#define SPRI_TM_EX_AC_AR 0x0001
|
|
uint8_t reserved[2];
|
|
};
|
|
|
|
struct scsi_per_res_in_rsrv_data
|
|
{
|
|
uint8_t reservation[8];
|
|
uint8_t obsolete1[4];
|
|
uint8_t reserved;
|
|
uint8_t scopetype;
|
|
#define SPRT_WE 0x01
|
|
#define SPRT_EA 0x03
|
|
#define SPRT_WERO 0x05
|
|
#define SPRT_EARO 0x06
|
|
#define SPRT_WEAR 0x07
|
|
#define SPRT_EAAR 0x08
|
|
uint8_t obsolete2[2];
|
|
};
|
|
|
|
struct scsi_per_res_in_rsrv
|
|
{
|
|
struct scsi_per_res_in_header header;
|
|
struct scsi_per_res_in_rsrv_data data;
|
|
};
|
|
|
|
struct scsi_per_res_out
|
|
{
|
|
u_int8_t opcode;
|
|
u_int8_t action;
|
|
#define SPRO_REGISTER 0x00
|
|
#define SPRO_RESERVE 0x01
|
|
#define SPRO_RELEASE 0x02
|
|
#define SPRO_CLEAR 0x03
|
|
#define SPRO_PREEMPT 0x04
|
|
#define SPRO_PRE_ABO 0x05
|
|
#define SPRO_REG_IGNO 0x06
|
|
#define SPRO_REG_MOVE 0x07
|
|
#define SPRO_ACTION_MASK 0x1f
|
|
u_int8_t scope_type;
|
|
#define SPR_SCOPE_MASK 0xf0
|
|
#define SPR_LU_SCOPE 0x00
|
|
#define SPR_TYPE_MASK 0x0f
|
|
#define SPR_TYPE_WR_EX 0x01
|
|
#define SPR_TYPE_EX_AC 0x03
|
|
#define SPR_TYPE_WR_EX_RO 0x05
|
|
#define SPR_TYPE_EX_AC_RO 0x06
|
|
#define SPR_TYPE_WR_EX_AR 0x07
|
|
#define SPR_TYPE_EX_AC_AR 0x08
|
|
u_int8_t reserved[2];
|
|
u_int8_t length[4];
|
|
u_int8_t control;
|
|
};
|
|
|
|
struct scsi_per_res_out_parms
|
|
{
|
|
struct scsi_per_res_key res_key;
|
|
u_int8_t serv_act_res_key[8];
|
|
u_int8_t obsolete1[4];
|
|
u_int8_t flags;
|
|
#define SPR_SPEC_I_PT 0x08
|
|
#define SPR_ALL_TG_PT 0x04
|
|
#define SPR_APTPL 0x01
|
|
u_int8_t reserved1;
|
|
u_int8_t obsolete2[2];
|
|
};
|
|
|
|
|
|
struct scsi_log_sense
|
|
{
|
|
u_int8_t opcode;
|
|
u_int8_t byte2;
|
|
#define SLS_SP 0x01
|
|
#define SLS_PPC 0x02
|
|
u_int8_t page;
|
|
#define SLS_PAGE_CODE 0x3F
|
|
#define SLS_ALL_PAGES_PAGE 0x00
|
|
#define SLS_OVERRUN_PAGE 0x01
|
|
#define SLS_ERROR_WRITE_PAGE 0x02
|
|
#define SLS_ERROR_READ_PAGE 0x03
|
|
#define SLS_ERROR_READREVERSE_PAGE 0x04
|
|
#define SLS_ERROR_VERIFY_PAGE 0x05
|
|
#define SLS_ERROR_NONMEDIUM_PAGE 0x06
|
|
#define SLS_ERROR_LASTN_PAGE 0x07
|
|
#define SLS_SELF_TEST_PAGE 0x10
|
|
#define SLS_IE_PAGE 0x2f
|
|
#define SLS_PAGE_CTRL_MASK 0xC0
|
|
#define SLS_PAGE_CTRL_THRESHOLD 0x00
|
|
#define SLS_PAGE_CTRL_CUMULATIVE 0x40
|
|
#define SLS_PAGE_CTRL_THRESH_DEFAULT 0x80
|
|
#define SLS_PAGE_CTRL_CUMUL_DEFAULT 0xC0
|
|
u_int8_t reserved[2];
|
|
u_int8_t paramptr[2];
|
|
u_int8_t length[2];
|
|
u_int8_t control;
|
|
};
|
|
|
|
struct scsi_log_select
|
|
{
|
|
u_int8_t opcode;
|
|
u_int8_t byte2;
|
|
/* SLS_SP 0x01 */
|
|
#define SLS_PCR 0x02
|
|
u_int8_t page;
|
|
/* SLS_PAGE_CTRL_MASK 0xC0 */
|
|
/* SLS_PAGE_CTRL_THRESHOLD 0x00 */
|
|
/* SLS_PAGE_CTRL_CUMULATIVE 0x40 */
|
|
/* SLS_PAGE_CTRL_THRESH_DEFAULT 0x80 */
|
|
/* SLS_PAGE_CTRL_CUMUL_DEFAULT 0xC0 */
|
|
u_int8_t reserved[4];
|
|
u_int8_t length[2];
|
|
u_int8_t control;
|
|
};
|
|
|
|
struct scsi_log_header
|
|
{
|
|
u_int8_t page;
|
|
u_int8_t reserved;
|
|
u_int8_t datalen[2];
|
|
};
|
|
|
|
struct scsi_log_param_header {
|
|
u_int8_t param_code[2];
|
|
u_int8_t param_control;
|
|
#define SLP_LP 0x01
|
|
#define SLP_LBIN 0x02
|
|
#define SLP_TMC_MASK 0x0C
|
|
#define SLP_TMC_ALWAYS 0x00
|
|
#define SLP_TMC_EQUAL 0x04
|
|
#define SLP_TMC_NOTEQUAL 0x08
|
|
#define SLP_TMC_GREATER 0x0C
|
|
#define SLP_ETC 0x10
|
|
#define SLP_TSD 0x20
|
|
#define SLP_DS 0x40
|
|
#define SLP_DU 0x80
|
|
u_int8_t param_len;
|
|
};
|
|
|
|
struct scsi_control_page {
|
|
u_int8_t page_code;
|
|
u_int8_t page_length;
|
|
u_int8_t rlec;
|
|
#define SCP_RLEC 0x01 /*Report Log Exception Cond*/
|
|
#define SCP_GLTSD 0x02 /*Global Logging target
|
|
save disable */
|
|
#define SCP_DSENSE 0x04 /*Descriptor Sense */
|
|
#define SCP_DPICZ 0x08 /*Disable Prot. Info Check
|
|
if Prot. Field is Zero */
|
|
#define SCP_TMF_ONLY 0x10 /*TM Functions Only*/
|
|
#define SCP_TST_MASK 0xE0 /*Task Set Type Mask*/
|
|
#define SCP_TST_ONE 0x00 /*One Task Set*/
|
|
#define SCP_TST_SEPARATE 0x20 /*Separate Task Sets*/
|
|
u_int8_t queue_flags;
|
|
#define SCP_QUEUE_ALG_MASK 0xF0
|
|
#define SCP_QUEUE_ALG_RESTRICTED 0x00
|
|
#define SCP_QUEUE_ALG_UNRESTRICTED 0x10
|
|
#define SCP_QUEUE_ERR 0x02 /*Queued I/O aborted for CACs*/
|
|
#define SCP_QUEUE_DQUE 0x01 /*Queued I/O disabled*/
|
|
u_int8_t eca_and_aen;
|
|
#define SCP_EECA 0x80 /*Enable Extended CA*/
|
|
#define SCP_RAENP 0x04 /*Ready AEN Permission*/
|
|
#define SCP_UAAENP 0x02 /*UA AEN Permission*/
|
|
#define SCP_EAENP 0x01 /*Error AEN Permission*/
|
|
u_int8_t reserved;
|
|
u_int8_t aen_holdoff_period[2];
|
|
};
|
|
|
|
struct scsi_cache_page {
|
|
u_int8_t page_code;
|
|
#define SCHP_PAGE_SAVABLE 0x80 /* Page is savable */
|
|
u_int8_t page_length;
|
|
u_int8_t cache_flags;
|
|
#define SCHP_FLAGS_WCE 0x04 /* Write Cache Enable */
|
|
#define SCHP_FLAGS_MF 0x02 /* Multiplication factor */
|
|
#define SCHP_FLAGS_RCD 0x01 /* Read Cache Disable */
|
|
u_int8_t rw_cache_policy;
|
|
u_int8_t dis_prefetch[2];
|
|
u_int8_t min_prefetch[2];
|
|
u_int8_t max_prefetch[2];
|
|
u_int8_t max_prefetch_ceil[2];
|
|
};
|
|
|
|
/*
|
|
* XXX KDM
|
|
* Updated version of the cache page, as of SBC. Update this to SBC-3 and
|
|
* rationalize the two.
|
|
*/
|
|
struct scsi_caching_page {
|
|
uint8_t page_code;
|
|
#define SMS_CACHING_PAGE 0x08
|
|
uint8_t page_length;
|
|
uint8_t flags1;
|
|
#define SCP_IC 0x80
|
|
#define SCP_ABPF 0x40
|
|
#define SCP_CAP 0x20
|
|
#define SCP_DISC 0x10
|
|
#define SCP_SIZE 0x08
|
|
#define SCP_WCE 0x04
|
|
#define SCP_MF 0x02
|
|
#define SCP_RCD 0x01
|
|
uint8_t ret_priority;
|
|
uint8_t disable_pf_transfer_len[2];
|
|
uint8_t min_prefetch[2];
|
|
uint8_t max_prefetch[2];
|
|
uint8_t max_pf_ceiling[2];
|
|
uint8_t flags2;
|
|
#define SCP_FSW 0x80
|
|
#define SCP_LBCSS 0x40
|
|
#define SCP_DRA 0x20
|
|
#define SCP_VS1 0x10
|
|
#define SCP_VS2 0x08
|
|
uint8_t cache_segments;
|
|
uint8_t cache_seg_size[2];
|
|
uint8_t reserved;
|
|
uint8_t non_cache_seg_size[3];
|
|
};
|
|
|
|
/*
|
|
* XXX KDM move this off to a vendor shim.
|
|
*/
|
|
struct copan_power_subpage {
|
|
uint8_t page_code;
|
|
#define PWR_PAGE_CODE 0x00
|
|
uint8_t subpage;
|
|
#define PWR_SUBPAGE_CODE 0x02
|
|
uint8_t page_length[2];
|
|
uint8_t page_version;
|
|
#define PWR_VERSION 0x01
|
|
uint8_t total_luns;
|
|
uint8_t max_active_luns;
|
|
#define PWR_DFLT_MAX_LUNS 0x07
|
|
uint8_t reserved[25];
|
|
};
|
|
|
|
/*
|
|
* XXX KDM move this off to a vendor shim.
|
|
*/
|
|
struct copan_aps_subpage {
|
|
uint8_t page_code;
|
|
#define APS_PAGE_CODE 0x00
|
|
uint8_t subpage;
|
|
#define APS_SUBPAGE_CODE 0x03
|
|
uint8_t page_length[2];
|
|
uint8_t page_version;
|
|
#define APS_VERSION 0x00
|
|
uint8_t lock_active;
|
|
#define APS_LOCK_ACTIVE 0x01
|
|
#define APS_LOCK_INACTIVE 0x00
|
|
uint8_t reserved[26];
|
|
};
|
|
|
|
/*
|
|
* XXX KDM move this off to a vendor shim.
|
|
*/
|
|
struct copan_debugconf_subpage {
|
|
uint8_t page_code;
|
|
#define DBGCNF_PAGE_CODE 0x00
|
|
uint8_t subpage;
|
|
#define DBGCNF_SUBPAGE_CODE 0xF0
|
|
uint8_t page_length[2];
|
|
uint8_t page_version;
|
|
#define DBGCNF_VERSION 0x00
|
|
uint8_t ctl_time_io_secs[2];
|
|
};
|
|
|
|
|
|
struct scsi_info_exceptions_page {
|
|
u_int8_t page_code;
|
|
#define SIEP_PAGE_SAVABLE 0x80 /* Page is savable */
|
|
u_int8_t page_length;
|
|
u_int8_t info_flags;
|
|
#define SIEP_FLAGS_PERF 0x80
|
|
#define SIEP_FLAGS_EBF 0x20
|
|
#define SIEP_FLAGS_EWASC 0x10
|
|
#define SIEP_FLAGS_DEXCPT 0x08
|
|
#define SIEP_FLAGS_TEST 0x04
|
|
#define SIEP_FLAGS_EBACKERR 0x02
|
|
#define SIEP_FLAGS_LOGERR 0x01
|
|
u_int8_t mrie;
|
|
u_int8_t interval_timer[4];
|
|
u_int8_t report_count[4];
|
|
};
|
|
|
|
struct scsi_proto_specific_page {
|
|
u_int8_t page_code;
|
|
#define SPSP_PAGE_SAVABLE 0x80 /* Page is savable */
|
|
u_int8_t page_length;
|
|
u_int8_t protocol;
|
|
#define SPSP_PROTO_FC 0x00
|
|
#define SPSP_PROTO_SPI 0x01
|
|
#define SPSP_PROTO_SSA 0x02
|
|
#define SPSP_PROTO_1394 0x03
|
|
#define SPSP_PROTO_RDMA 0x04
|
|
#define SPSP_PROTO_ISCSI 0x05
|
|
#define SPSP_PROTO_SAS 0x06
|
|
#define SPSP_PROTO_ADT 0x07
|
|
#define SPSP_PROTO_ATA 0x08
|
|
#define SPSP_PROTO_NONE 0x0f
|
|
};
|
|
|
|
struct scsi_reserve
|
|
{
|
|
u_int8_t opcode;
|
|
u_int8_t byte2;
|
|
#define SR_EXTENT 0x01
|
|
#define SR_ID_MASK 0x0e
|
|
#define SR_3RDPTY 0x10
|
|
#define SR_LUN_MASK 0xe0
|
|
u_int8_t resv_id;
|
|
u_int8_t length[2];
|
|
u_int8_t control;
|
|
};
|
|
|
|
struct scsi_reserve_10 {
|
|
uint8_t opcode;
|
|
uint8_t byte2;
|
|
#define SR10_3RDPTY 0x10
|
|
#define SR10_LONGID 0x02
|
|
#define SR10_EXTENT 0x01
|
|
uint8_t resv_id;
|
|
uint8_t thirdparty_id;
|
|
uint8_t reserved[3];
|
|
uint8_t length[2];
|
|
uint8_t control;
|
|
};
|
|
|
|
|
|
struct scsi_release
|
|
{
|
|
u_int8_t opcode;
|
|
u_int8_t byte2;
|
|
u_int8_t resv_id;
|
|
u_int8_t unused[1];
|
|
u_int8_t length;
|
|
u_int8_t control;
|
|
};
|
|
|
|
struct scsi_release_10 {
|
|
uint8_t opcode;
|
|
uint8_t byte2;
|
|
uint8_t resv_id;
|
|
uint8_t thirdparty_id;
|
|
uint8_t reserved[3];
|
|
uint8_t length[2];
|
|
uint8_t control;
|
|
};
|
|
|
|
struct scsi_prevent
|
|
{
|
|
u_int8_t opcode;
|
|
u_int8_t byte2;
|
|
u_int8_t unused[2];
|
|
u_int8_t how;
|
|
u_int8_t control;
|
|
};
|
|
#define PR_PREVENT 0x01
|
|
#define PR_ALLOW 0x00
|
|
|
|
struct scsi_sync_cache
|
|
{
|
|
u_int8_t opcode;
|
|
u_int8_t byte2;
|
|
#define SSC_IMMED 0x02
|
|
#define SSC_RELADR 0x01
|
|
u_int8_t begin_lba[4];
|
|
u_int8_t reserved;
|
|
u_int8_t lb_count[2];
|
|
u_int8_t control;
|
|
};
|
|
|
|
struct scsi_sync_cache_16
|
|
{
|
|
uint8_t opcode;
|
|
uint8_t byte2;
|
|
uint8_t begin_lba[8];
|
|
uint8_t lb_count[4];
|
|
uint8_t reserved;
|
|
uint8_t control;
|
|
};
|
|
|
|
struct scsi_format {
|
|
uint8_t opcode;
|
|
uint8_t byte2;
|
|
#define SF_LONGLIST 0x20
|
|
#define SF_FMTDATA 0x10
|
|
#define SF_CMPLIST 0x08
|
|
#define SF_FORMAT_MASK 0x07
|
|
#define SF_FORMAT_BLOCK 0x00
|
|
#define SF_FORMAT_LONG_BLOCK 0x03
|
|
#define SF_FORMAT_BFI 0x04
|
|
#define SF_FORMAT_PHYS 0x05
|
|
uint8_t vendor;
|
|
uint8_t interleave[2];
|
|
uint8_t control;
|
|
};
|
|
|
|
struct scsi_format_header_short {
|
|
uint8_t reserved;
|
|
#define SF_DATA_FOV 0x80
|
|
#define SF_DATA_DPRY 0x40
|
|
#define SF_DATA_DCRT 0x20
|
|
#define SF_DATA_STPF 0x10
|
|
#define SF_DATA_IP 0x08
|
|
#define SF_DATA_DSP 0x04
|
|
#define SF_DATA_IMMED 0x02
|
|
#define SF_DATA_VS 0x01
|
|
uint8_t byte2;
|
|
uint8_t defect_list_len[2];
|
|
};
|
|
|
|
struct scsi_format_header_long {
|
|
uint8_t reserved;
|
|
uint8_t byte2;
|
|
uint8_t reserved2[2];
|
|
uint8_t defect_list_len[4];
|
|
};
|
|
|
|
struct scsi_changedef
|
|
{
|
|
u_int8_t opcode;
|
|
u_int8_t byte2;
|
|
u_int8_t unused1;
|
|
u_int8_t how;
|
|
u_int8_t unused[4];
|
|
u_int8_t datalen;
|
|
u_int8_t control;
|
|
};
|
|
|
|
struct scsi_read_buffer
|
|
{
|
|
u_int8_t opcode;
|
|
u_int8_t byte2;
|
|
#define RWB_MODE 0x07
|
|
#define RWB_MODE_HDR_DATA 0x00
|
|
#define RWB_MODE_VENDOR 0x01
|
|
#define RWB_MODE_DATA 0x02
|
|
#define RWB_MODE_DOWNLOAD 0x04
|
|
#define RWB_MODE_DOWNLOAD_SAVE 0x05
|
|
u_int8_t buffer_id;
|
|
u_int8_t offset[3];
|
|
u_int8_t length[3];
|
|
u_int8_t control;
|
|
};
|
|
|
|
struct scsi_write_buffer
|
|
{
|
|
u_int8_t opcode;
|
|
u_int8_t byte2;
|
|
u_int8_t buffer_id;
|
|
u_int8_t offset[3];
|
|
u_int8_t length[3];
|
|
u_int8_t control;
|
|
};
|
|
|
|
struct scsi_rw_6
|
|
{
|
|
u_int8_t opcode;
|
|
u_int8_t addr[3];
|
|
/* only 5 bits are valid in the MSB address byte */
|
|
#define SRW_TOPADDR 0x1F
|
|
u_int8_t length;
|
|
u_int8_t control;
|
|
};
|
|
|
|
struct scsi_rw_10
|
|
{
|
|
u_int8_t opcode;
|
|
#define SRW10_RELADDR 0x01
|
|
/* EBP defined for WRITE(10) only */
|
|
#define SRW10_EBP 0x04
|
|
#define SRW10_FUA 0x08
|
|
#define SRW10_DPO 0x10
|
|
u_int8_t byte2;
|
|
u_int8_t addr[4];
|
|
u_int8_t reserved;
|
|
u_int8_t length[2];
|
|
u_int8_t control;
|
|
};
|
|
|
|
struct scsi_rw_12
|
|
{
|
|
u_int8_t opcode;
|
|
#define SRW12_RELADDR 0x01
|
|
#define SRW12_FUA 0x08
|
|
#define SRW12_DPO 0x10
|
|
u_int8_t byte2;
|
|
u_int8_t addr[4];
|
|
u_int8_t length[4];
|
|
u_int8_t reserved;
|
|
u_int8_t control;
|
|
};
|
|
|
|
struct scsi_rw_16
|
|
{
|
|
u_int8_t opcode;
|
|
#define SRW16_RELADDR 0x01
|
|
#define SRW16_FUA 0x08
|
|
#define SRW16_DPO 0x10
|
|
u_int8_t byte2;
|
|
u_int8_t addr[8];
|
|
u_int8_t length[4];
|
|
u_int8_t reserved;
|
|
u_int8_t control;
|
|
};
|
|
|
|
struct scsi_write_same_10
|
|
{
|
|
uint8_t opcode;
|
|
uint8_t byte2;
|
|
#define SWS_LBDATA 0x02
|
|
#define SWS_PBDATA 0x04
|
|
#define SWS_UNMAP 0x08
|
|
#define SWS_ANCHOR 0x10
|
|
uint8_t addr[4];
|
|
uint8_t group;
|
|
uint8_t length[2];
|
|
uint8_t control;
|
|
};
|
|
|
|
struct scsi_write_same_16
|
|
{
|
|
uint8_t opcode;
|
|
uint8_t byte2;
|
|
uint8_t addr[8];
|
|
uint8_t length[4];
|
|
uint8_t group;
|
|
uint8_t control;
|
|
};
|
|
|
|
struct scsi_unmap
|
|
{
|
|
uint8_t opcode;
|
|
uint8_t byte2;
|
|
#define SU_ANCHOR 0x01
|
|
uint8_t reserved[4];
|
|
uint8_t group;
|
|
uint8_t length[2];
|
|
uint8_t control;
|
|
};
|
|
|
|
struct scsi_write_verify_10
|
|
{
|
|
uint8_t opcode;
|
|
uint8_t byte2;
|
|
#define SWV_BYTCHK 0x02
|
|
#define SWV_DPO 0x10
|
|
#define SWV_WRPROECT_MASK 0xe0
|
|
uint8_t addr[4];
|
|
uint8_t group;
|
|
uint8_t length[2];
|
|
uint8_t control;
|
|
};
|
|
|
|
struct scsi_write_verify_12
|
|
{
|
|
uint8_t opcode;
|
|
uint8_t byte2;
|
|
uint8_t addr[4];
|
|
uint8_t length[4];
|
|
uint8_t group;
|
|
uint8_t control;
|
|
};
|
|
|
|
struct scsi_write_verify_16
|
|
{
|
|
uint8_t opcode;
|
|
uint8_t byte2;
|
|
uint8_t addr[8];
|
|
uint8_t length[4];
|
|
uint8_t group;
|
|
uint8_t control;
|
|
};
|
|
|
|
|
|
struct scsi_start_stop_unit
|
|
{
|
|
u_int8_t opcode;
|
|
u_int8_t byte2;
|
|
#define SSS_IMMED 0x01
|
|
u_int8_t reserved[2];
|
|
u_int8_t how;
|
|
#define SSS_START 0x01
|
|
#define SSS_LOEJ 0x02
|
|
#define SSS_PC_MASK 0xf0
|
|
#define SSS_PC_START_VALID 0x00
|
|
#define SSS_PC_ACTIVE 0x10
|
|
#define SSS_PC_IDLE 0x20
|
|
#define SSS_PC_STANDBY 0x30
|
|
#define SSS_PC_LU_CONTROL 0x70
|
|
#define SSS_PC_FORCE_IDLE_0 0xa0
|
|
#define SSS_PC_FORCE_STANDBY_0 0xb0
|
|
u_int8_t control;
|
|
};
|
|
|
|
struct ata_pass_12 {
|
|
u_int8_t opcode;
|
|
u_int8_t protocol;
|
|
#define AP_MULTI 0xe0
|
|
u_int8_t flags;
|
|
#define AP_T_LEN 0x03
|
|
#define AP_BB 0x04
|
|
#define AP_T_DIR 0x08
|
|
#define AP_CK_COND 0x20
|
|
#define AP_OFFLINE 0x60
|
|
u_int8_t features;
|
|
u_int8_t sector_count;
|
|
u_int8_t lba_low;
|
|
u_int8_t lba_mid;
|
|
u_int8_t lba_high;
|
|
u_int8_t device;
|
|
u_int8_t command;
|
|
u_int8_t reserved;
|
|
u_int8_t control;
|
|
};
|
|
|
|
struct scsi_maintenance_in
|
|
{
|
|
uint8_t opcode;
|
|
uint8_t byte2;
|
|
#define SERVICE_ACTION_MASK 0x1f
|
|
#define SA_RPRT_TRGT_GRP 0x0a
|
|
uint8_t reserved[4];
|
|
uint8_t length[4];
|
|
uint8_t reserved1;
|
|
uint8_t control;
|
|
};
|
|
|
|
struct ata_pass_16 {
|
|
u_int8_t opcode;
|
|
u_int8_t protocol;
|
|
#define AP_EXTEND 0x01
|
|
u_int8_t flags;
|
|
u_int8_t features_ext;
|
|
u_int8_t features;
|
|
u_int8_t sector_count_ext;
|
|
u_int8_t sector_count;
|
|
u_int8_t lba_low_ext;
|
|
u_int8_t lba_low;
|
|
u_int8_t lba_mid_ext;
|
|
u_int8_t lba_mid;
|
|
u_int8_t lba_high_ext;
|
|
u_int8_t lba_high;
|
|
u_int8_t device;
|
|
u_int8_t command;
|
|
u_int8_t control;
|
|
};
|
|
|
|
#define SC_SCSI_1 0x01
|
|
#define SC_SCSI_2 0x03
|
|
|
|
/*
|
|
* Opcodes
|
|
*/
|
|
|
|
#define TEST_UNIT_READY 0x00
|
|
#define REQUEST_SENSE 0x03
|
|
#define READ_6 0x08
|
|
#define WRITE_6 0x0A
|
|
#define INQUIRY 0x12
|
|
#define MODE_SELECT_6 0x15
|
|
#define MODE_SENSE_6 0x1A
|
|
#define START_STOP_UNIT 0x1B
|
|
#define START_STOP 0x1B
|
|
#define RESERVE 0x16
|
|
#define RELEASE 0x17
|
|
#define RECEIVE_DIAGNOSTIC 0x1C
|
|
#define SEND_DIAGNOSTIC 0x1D
|
|
#define PREVENT_ALLOW 0x1E
|
|
#define READ_CAPACITY 0x25
|
|
#define READ_10 0x28
|
|
#define WRITE_10 0x2A
|
|
#define POSITION_TO_ELEMENT 0x2B
|
|
#define WRITE_VERIFY_10 0x2E
|
|
#define VERIFY_10 0x2F
|
|
#define SYNCHRONIZE_CACHE 0x35
|
|
#define READ_DEFECT_DATA_10 0x37
|
|
#define WRITE_BUFFER 0x3B
|
|
#define READ_BUFFER 0x3C
|
|
#define CHANGE_DEFINITION 0x40
|
|
#define WRITE_SAME_10 0x41
|
|
#define UNMAP 0x42
|
|
#define LOG_SELECT 0x4C
|
|
#define LOG_SENSE 0x4D
|
|
#define MODE_SELECT_10 0x55
|
|
#define RESERVE_10 0x56
|
|
#define RELEASE_10 0x57
|
|
#define MODE_SENSE_10 0x5A
|
|
#define PERSISTENT_RES_IN 0x5E
|
|
#define PERSISTENT_RES_OUT 0x5F
|
|
#define ATA_PASS_16 0x85
|
|
#define READ_16 0x88
|
|
#define WRITE_16 0x8A
|
|
#define WRITE_VERIFY_16 0x8E
|
|
#define SYNCHRONIZE_CACHE_16 0x91
|
|
#define WRITE_SAME_16 0x93
|
|
#define SERVICE_ACTION_IN 0x9E
|
|
#define REPORT_LUNS 0xA0
|
|
#define ATA_PASS_12 0xA1
|
|
#define MAINTENANCE_IN 0xA3
|
|
#define MAINTENANCE_OUT 0xA4
|
|
#define MOVE_MEDIUM 0xA5
|
|
#define READ_12 0xA8
|
|
#define WRITE_12 0xAA
|
|
#define WRITE_VERIFY_12 0xAE
|
|
#define READ_ELEMENT_STATUS 0xB8
|
|
#define READ_CD 0xBE
|
|
|
|
/* Maintenance In Service Action Codes */
|
|
#define REPORT_IDENTIFYING_INFRMATION 0x05
|
|
#define REPORT_TARGET_PORT_GROUPS 0x0A
|
|
#define REPORT_ALIASES 0x0B
|
|
#define REPORT_SUPPORTED_OPERATION_CODES 0x0C
|
|
#define REPORT_SUPPORTED_TASK_MANAGEMENT_FUNCTIONS 0x0D
|
|
#define REPORT_PRIORITY 0x0E
|
|
#define REPORT_TIMESTAMP 0x0F
|
|
#define MANAGEMENT_PROTOCOL_IN 0x10
|
|
/* Maintenance Out Service Action Codes */
|
|
#define SET_IDENTIFY_INFORMATION 0x06
|
|
#define SET_TARGET_PORT_GROUPS 0x0A
|
|
#define CHANGE_ALIASES 0x0B
|
|
#define SET_PRIORITY 0x0E
|
|
#define SET_TIMESTAMP 0x0F
|
|
#define MANGAEMENT_PROTOCOL_OUT 0x10
|
|
|
|
/*
|
|
* Device Types
|
|
*/
|
|
#define T_DIRECT 0x00
|
|
#define T_SEQUENTIAL 0x01
|
|
#define T_PRINTER 0x02
|
|
#define T_PROCESSOR 0x03
|
|
#define T_WORM 0x04
|
|
#define T_CDROM 0x05
|
|
#define T_SCANNER 0x06
|
|
#define T_OPTICAL 0x07
|
|
#define T_CHANGER 0x08
|
|
#define T_COMM 0x09
|
|
#define T_ASC0 0x0a
|
|
#define T_ASC1 0x0b
|
|
#define T_STORARRAY 0x0c
|
|
#define T_ENCLOSURE 0x0d
|
|
#define T_RBC 0x0e
|
|
#define T_OCRW 0x0f
|
|
#define T_OSD 0x11
|
|
#define T_ADC 0x12
|
|
#define T_NODEVICE 0x1f
|
|
#define T_ANY 0xff /* Used in Quirk table matches */
|
|
|
|
#define T_REMOV 1
|
|
#define T_FIXED 0
|
|
|
|
/*
|
|
* This length is the initial inquiry length used by the probe code, as
|
|
* well as the legnth necessary for scsi_print_inquiry() to function
|
|
* correctly. If either use requires a different length in the future,
|
|
* the two values should be de-coupled.
|
|
*/
|
|
#define SHORT_INQUIRY_LENGTH 36
|
|
|
|
struct scsi_inquiry_data
|
|
{
|
|
u_int8_t device;
|
|
#define SID_TYPE(inq_data) ((inq_data)->device & 0x1f)
|
|
#define SID_QUAL(inq_data) (((inq_data)->device & 0xE0) >> 5)
|
|
#define SID_QUAL_LU_CONNECTED 0x00 /*
|
|
* The specified peripheral device
|
|
* type is currently connected to
|
|
* logical unit. If the target cannot
|
|
* determine whether or not a physical
|
|
* device is currently connected, it
|
|
* shall also use this peripheral
|
|
* qualifier when returning the INQUIRY
|
|
* data. This peripheral qualifier
|
|
* does not mean that the device is
|
|
* ready for access by the initiator.
|
|
*/
|
|
#define SID_QUAL_LU_OFFLINE 0x01 /*
|
|
* The target is capable of supporting
|
|
* the specified peripheral device type
|
|
* on this logical unit; however, the
|
|
* physical device is not currently
|
|
* connected to this logical unit.
|
|
*/
|
|
#define SID_QUAL_RSVD 0x02
|
|
#define SID_QUAL_BAD_LU 0x03 /*
|
|
* The target is not capable of
|
|
* supporting a physical device on
|
|
* this logical unit. For this
|
|
* peripheral qualifier the peripheral
|
|
* device type shall be set to 1Fh to
|
|
* provide compatibility with previous
|
|
* versions of SCSI. All other
|
|
* peripheral device type values are
|
|
* reserved for this peripheral
|
|
* qualifier.
|
|
*/
|
|
#define SID_QUAL_IS_VENDOR_UNIQUE(inq_data) ((SID_QUAL(inq_data) & 0x08) != 0)
|
|
u_int8_t dev_qual2;
|
|
#define SID_QUAL2 0x7F
|
|
#define SID_IS_REMOVABLE(inq_data) (((inq_data)->dev_qual2 & 0x80) != 0)
|
|
u_int8_t version;
|
|
#define SID_ANSI_REV(inq_data) ((inq_data)->version & 0x07)
|
|
#define SCSI_REV_0 0
|
|
#define SCSI_REV_CCS 1
|
|
#define SCSI_REV_2 2
|
|
#define SCSI_REV_SPC 3
|
|
#define SCSI_REV_SPC2 4
|
|
#define SCSI_REV_SPC3 5
|
|
#define SCSI_REV_SPC4 6
|
|
|
|
#define SID_ECMA 0x38
|
|
#define SID_ISO 0xC0
|
|
u_int8_t response_format;
|
|
#define SID_AENC 0x80
|
|
#define SID_TrmIOP 0x40
|
|
#define SID_NormACA 0x20
|
|
#define SID_HiSup 0x10
|
|
u_int8_t additional_length;
|
|
#define SID_ADDITIONAL_LENGTH(iqd) \
|
|
((iqd)->additional_length + \
|
|
__offsetof(struct scsi_inquiry_data, additional_length) + 1)
|
|
u_int8_t spc3_flags;
|
|
#define SPC3_SID_PROTECT 0x01
|
|
#define SPC3_SID_3PC 0x08
|
|
#define SPC3_SID_TPGS_MASK 0x30
|
|
#define SPC3_SID_TPGS_IMPLICIT 0x10
|
|
#define SPC3_SID_TPGS_EXPLICIT 0x20
|
|
#define SPC3_SID_ACC 0x40
|
|
#define SPC3_SID_SCCS 0x80
|
|
u_int8_t spc2_flags;
|
|
#define SPC2_SID_ADDR16 0x01
|
|
#define SPC2_SID_MChngr 0x08
|
|
#define SPC2_SID_MultiP 0x10
|
|
#define SPC2_SID_EncServ 0x40
|
|
#define SPC2_SID_BQueue 0x80
|
|
|
|
#define INQ_DATA_TQ_ENABLED(iqd) \
|
|
((SID_ANSI_REV(iqd) < SCSI_REV_SPC2)? ((iqd)->flags & SID_CmdQue) : \
|
|
(((iqd)->flags & SID_CmdQue) && !((iqd)->spc2_flags & SPC2_SID_BQueue)) || \
|
|
(!((iqd)->flags & SID_CmdQue) && ((iqd)->spc2_flags & SPC2_SID_BQueue)))
|
|
|
|
u_int8_t flags;
|
|
#define SID_SftRe 0x01
|
|
#define SID_CmdQue 0x02
|
|
#define SID_Linked 0x08
|
|
#define SID_Sync 0x10
|
|
#define SID_WBus16 0x20
|
|
#define SID_WBus32 0x40
|
|
#define SID_RelAdr 0x80
|
|
#define SID_VENDOR_SIZE 8
|
|
char vendor[SID_VENDOR_SIZE];
|
|
#define SID_PRODUCT_SIZE 16
|
|
char product[SID_PRODUCT_SIZE];
|
|
#define SID_REVISION_SIZE 4
|
|
char revision[SID_REVISION_SIZE];
|
|
/*
|
|
* The following fields were taken from SCSI Primary Commands - 2
|
|
* (SPC-2) Revision 14, Dated 11 November 1999
|
|
*/
|
|
#define SID_VENDOR_SPECIFIC_0_SIZE 20
|
|
u_int8_t vendor_specific0[SID_VENDOR_SPECIFIC_0_SIZE];
|
|
/*
|
|
* An extension of SCSI Parallel Specific Values
|
|
*/
|
|
#define SID_SPI_IUS 0x01
|
|
#define SID_SPI_QAS 0x02
|
|
#define SID_SPI_CLOCK_ST 0x00
|
|
#define SID_SPI_CLOCK_DT 0x04
|
|
#define SID_SPI_CLOCK_DT_ST 0x0C
|
|
#define SID_SPI_MASK 0x0F
|
|
u_int8_t spi3data;
|
|
u_int8_t reserved2;
|
|
/*
|
|
* Version Descriptors, stored 2 byte values.
|
|
*/
|
|
u_int8_t version1[2];
|
|
u_int8_t version2[2];
|
|
u_int8_t version3[2];
|
|
u_int8_t version4[2];
|
|
u_int8_t version5[2];
|
|
u_int8_t version6[2];
|
|
u_int8_t version7[2];
|
|
u_int8_t version8[2];
|
|
|
|
u_int8_t reserved3[22];
|
|
|
|
#define SID_VENDOR_SPECIFIC_1_SIZE 160
|
|
u_int8_t vendor_specific1[SID_VENDOR_SPECIFIC_1_SIZE];
|
|
};
|
|
|
|
/*
|
|
* This structure is more suited to initiator operation, because the
|
|
* maximum number of supported pages is already allocated.
|
|
*/
|
|
struct scsi_vpd_supported_page_list
|
|
{
|
|
u_int8_t device;
|
|
u_int8_t page_code;
|
|
#define SVPD_SUPPORTED_PAGE_LIST 0x00
|
|
#define SVPD_SUPPORTED_PAGES_HDR_LEN 4
|
|
u_int8_t reserved;
|
|
u_int8_t length; /* number of VPD entries */
|
|
#define SVPD_SUPPORTED_PAGES_SIZE 251
|
|
u_int8_t list[SVPD_SUPPORTED_PAGES_SIZE];
|
|
};
|
|
|
|
/*
|
|
* This structure is more suited to target operation, because the
|
|
* number of supported pages is left to the user to allocate.
|
|
*/
|
|
struct scsi_vpd_supported_pages
|
|
{
|
|
u_int8_t device;
|
|
u_int8_t page_code;
|
|
u_int8_t reserved;
|
|
#define SVPD_SUPPORTED_PAGES 0x00
|
|
u_int8_t length;
|
|
u_int8_t page_list[0];
|
|
};
|
|
|
|
|
|
struct scsi_vpd_unit_serial_number
|
|
{
|
|
u_int8_t device;
|
|
u_int8_t page_code;
|
|
#define SVPD_UNIT_SERIAL_NUMBER 0x80
|
|
u_int8_t reserved;
|
|
u_int8_t length; /* serial number length */
|
|
#define SVPD_SERIAL_NUM_SIZE 251
|
|
u_int8_t serial_num[SVPD_SERIAL_NUM_SIZE];
|
|
};
|
|
|
|
struct scsi_vpd_device_id
|
|
{
|
|
u_int8_t device;
|
|
u_int8_t page_code;
|
|
#define SVPD_DEVICE_ID 0x83
|
|
#define SVPD_DEVICE_ID_MAX_SIZE 252
|
|
#define SVPD_DEVICE_ID_HDR_LEN \
|
|
__offsetof(struct scsi_vpd_device_id, desc_list)
|
|
u_int8_t length[2];
|
|
u_int8_t desc_list[];
|
|
};
|
|
|
|
struct scsi_vpd_id_descriptor
|
|
{
|
|
u_int8_t proto_codeset;
|
|
#define SCSI_PROTO_FC 0x00
|
|
#define SCSI_PROTO_SPI 0x01
|
|
#define SCSI_PROTO_SSA 0x02
|
|
#define SCSI_PROTO_1394 0x03
|
|
#define SCSI_PROTO_RDMA 0x04
|
|
#define SCSI_PROTO_iSCSI 0x05
|
|
#define SCSI_PROTO_SAS 0x06
|
|
#define SCSI_PROTO_ADT 0x07
|
|
#define SCSI_PROTO_ATA 0x08
|
|
#define SVPD_ID_PROTO_SHIFT 4
|
|
#define SVPD_ID_CODESET_BINARY 0x01
|
|
#define SVPD_ID_CODESET_ASCII 0x02
|
|
#define SVPD_ID_CODESET_MASK 0x0f
|
|
u_int8_t id_type;
|
|
#define SVPD_ID_PIV 0x80
|
|
#define SVPD_ID_ASSOC_LUN 0x00
|
|
#define SVPD_ID_ASSOC_PORT 0x10
|
|
#define SVPD_ID_ASSOC_TARGET 0x20
|
|
#define SVPD_ID_ASSOC_MASK 0x30
|
|
#define SVPD_ID_TYPE_VENDOR 0x00
|
|
#define SVPD_ID_TYPE_T10 0x01
|
|
#define SVPD_ID_TYPE_EUI64 0x02
|
|
#define SVPD_ID_TYPE_NAA 0x03
|
|
#define SVPD_ID_TYPE_RELTARG 0x04
|
|
#define SVPD_ID_TYPE_TPORTGRP 0x05
|
|
#define SVPD_ID_TYPE_LUNGRP 0x06
|
|
#define SVPD_ID_TYPE_MD5_LUN_ID 0x07
|
|
#define SVPD_ID_TYPE_SCSI_NAME 0x08
|
|
#define SVPD_ID_TYPE_MASK 0x0f
|
|
u_int8_t reserved;
|
|
u_int8_t length;
|
|
#define SVPD_DEVICE_ID_DESC_HDR_LEN \
|
|
__offsetof(struct scsi_vpd_id_descriptor, identifier)
|
|
u_int8_t identifier[];
|
|
};
|
|
|
|
struct scsi_vpd_id_t10
|
|
{
|
|
u_int8_t vendor[8];
|
|
u_int8_t vendor_spec_id[0];
|
|
};
|
|
|
|
struct scsi_vpd_id_eui64
|
|
{
|
|
u_int8_t ieee_company_id[3];
|
|
u_int8_t extension_id[5];
|
|
};
|
|
|
|
struct scsi_vpd_id_naa_basic
|
|
{
|
|
uint8_t naa;
|
|
/* big endian, packed:
|
|
uint8_t naa : 4;
|
|
uint8_t naa_desig : 4;
|
|
*/
|
|
#define SVPD_ID_NAA_NAA_SHIFT 4
|
|
#define SVPD_ID_NAA_IEEE_EXT 0x02
|
|
#define SVPD_ID_NAA_LOCAL_REG 0x03
|
|
#define SVPD_ID_NAA_IEEE_REG 0x05
|
|
#define SVPD_ID_NAA_IEEE_REG_EXT 0x06
|
|
uint8_t naa_data[];
|
|
};
|
|
|
|
struct scsi_vpd_id_naa_ieee_extended_id
|
|
{
|
|
uint8_t naa;
|
|
uint8_t vendor_specific_id_a;
|
|
uint8_t ieee_company_id[3];
|
|
uint8_t vendor_specific_id_b[4];
|
|
};
|
|
|
|
struct scsi_vpd_id_naa_local_reg
|
|
{
|
|
uint8_t naa;
|
|
uint8_t local_value[7];
|
|
};
|
|
|
|
struct scsi_vpd_id_naa_ieee_reg
|
|
{
|
|
uint8_t naa;
|
|
uint8_t reg_value[7];
|
|
/* big endian, packed:
|
|
uint8_t naa_basic : 4;
|
|
uint8_t ieee_company_id_0 : 4;
|
|
uint8_t ieee_company_id_1[2];
|
|
uint8_t ieee_company_id_2 : 4;
|
|
uint8_t vendor_specific_id_0 : 4;
|
|
uint8_t vendor_specific_id_1[4];
|
|
*/
|
|
};
|
|
|
|
struct scsi_vpd_id_naa_ieee_reg_extended
|
|
{
|
|
uint8_t naa;
|
|
uint8_t reg_value[15];
|
|
/* big endian, packed:
|
|
uint8_t naa_basic : 4;
|
|
uint8_t ieee_company_id_0 : 4;
|
|
uint8_t ieee_company_id_1[2];
|
|
uint8_t ieee_company_id_2 : 4;
|
|
uint8_t vendor_specific_id_0 : 4;
|
|
uint8_t vendor_specific_id_1[4];
|
|
uint8_t vendor_specific_id_ext[8];
|
|
*/
|
|
};
|
|
|
|
struct scsi_vpd_id_rel_trgt_port_id
|
|
{
|
|
uint8_t obsolete[2];
|
|
uint8_t rel_trgt_port_id[2];
|
|
};
|
|
|
|
struct scsi_vpd_id_trgt_port_grp_id
|
|
{
|
|
uint8_t reserved[2];
|
|
uint8_t trgt_port_grp[2];
|
|
};
|
|
|
|
struct scsi_vpd_id_lun_grp_id
|
|
{
|
|
uint8_t reserved[2];
|
|
uint8_t log_unit_grp[2];
|
|
};
|
|
|
|
struct scsi_vpd_id_md5_lun_id
|
|
{
|
|
uint8_t lun_id[16];
|
|
};
|
|
|
|
struct scsi_vpd_id_scsi_name
|
|
{
|
|
uint8_t name_string[256];
|
|
};
|
|
|
|
struct scsi_service_action_in
|
|
{
|
|
uint8_t opcode;
|
|
uint8_t service_action;
|
|
uint8_t action_dependent[13];
|
|
uint8_t control;
|
|
};
|
|
|
|
struct scsi_diag_page {
|
|
uint8_t page_code;
|
|
uint8_t page_specific_flags;
|
|
uint8_t length[2];
|
|
uint8_t params[0];
|
|
};
|
|
|
|
struct scsi_read_capacity
|
|
{
|
|
u_int8_t opcode;
|
|
u_int8_t byte2;
|
|
#define SRC_RELADR 0x01
|
|
u_int8_t addr[4];
|
|
u_int8_t unused[2];
|
|
u_int8_t pmi;
|
|
#define SRC_PMI 0x01
|
|
u_int8_t control;
|
|
};
|
|
|
|
struct scsi_read_capacity_16
|
|
{
|
|
uint8_t opcode;
|
|
#define SRC16_SERVICE_ACTION 0x10
|
|
uint8_t service_action;
|
|
uint8_t addr[8];
|
|
uint8_t alloc_len[4];
|
|
#define SRC16_PMI 0x01
|
|
#define SRC16_RELADR 0x02
|
|
uint8_t reladr;
|
|
uint8_t control;
|
|
};
|
|
|
|
struct scsi_read_capacity_data
|
|
{
|
|
u_int8_t addr[4];
|
|
u_int8_t length[4];
|
|
};
|
|
|
|
struct scsi_read_capacity_data_long
|
|
{
|
|
uint8_t addr[8];
|
|
uint8_t length[4];
|
|
#define SRC16_PROT_EN 0x01
|
|
#define SRC16_P_TYPE 0x0e
|
|
#define SRC16_PTYPE_1 0x00
|
|
#define SRC16_PTYPE_2 0x02
|
|
#define SRC16_PTYPE_3 0x04
|
|
uint8_t prot;
|
|
#define SRC16_LBPPBE 0x0f
|
|
#define SRC16_PI_EXPONENT 0xf0
|
|
#define SRC16_PI_EXPONENT_SHIFT 4
|
|
uint8_t prot_lbppbe;
|
|
#define SRC16_LALBA 0x3f
|
|
#define SRC16_LBPRZ 0x40
|
|
#define SRC16_LBPME 0x80
|
|
/*
|
|
* Alternate versions of these macros that are intended for use on a 16-bit
|
|
* version of the lalba_lbp field instead of the array of 2 8 bit numbers.
|
|
*/
|
|
#define SRC16_LALBA_A 0x3fff
|
|
#define SRC16_LBPRZ_A 0x4000
|
|
#define SRC16_LBPME_A 0x8000
|
|
uint8_t lalba_lbp[2];
|
|
uint8_t reserved[16];
|
|
};
|
|
|
|
struct scsi_report_luns
|
|
{
|
|
uint8_t opcode;
|
|
uint8_t reserved1;
|
|
#define RPL_REPORT_DEFAULT 0x00
|
|
#define RPL_REPORT_WELLKNOWN 0x01
|
|
#define RPL_REPORT_ALL 0x02
|
|
uint8_t select_report;
|
|
uint8_t reserved2[3];
|
|
uint8_t length[4];
|
|
uint8_t reserved3;
|
|
uint8_t control;
|
|
};
|
|
|
|
struct scsi_report_luns_lundata {
|
|
uint8_t lundata[8];
|
|
#define RPL_LUNDATA_PERIPH_BUS_MASK 0x3f
|
|
#define RPL_LUNDATA_FLAT_LUN_MASK 0x3f
|
|
#define RPL_LUNDATA_FLAT_LUN_BITS 0x06
|
|
#define RPL_LUNDATA_LUN_TARG_MASK 0x3f
|
|
#define RPL_LUNDATA_LUN_BUS_MASK 0xe0
|
|
#define RPL_LUNDATA_LUN_LUN_MASK 0x1f
|
|
#define RPL_LUNDATA_EXT_LEN_MASK 0x30
|
|
#define RPL_LUNDATA_EXT_EAM_MASK 0x0f
|
|
#define RPL_LUNDATA_EXT_EAM_WK 0x01
|
|
#define RPL_LUNDATA_EXT_EAM_NOT_SPEC 0x0f
|
|
#define RPL_LUNDATA_ATYP_MASK 0xc0 /* MBZ for type 0 lun */
|
|
#define RPL_LUNDATA_ATYP_PERIPH 0x00
|
|
#define RPL_LUNDATA_ATYP_FLAT 0x40
|
|
#define RPL_LUNDATA_ATYP_LUN 0x80
|
|
#define RPL_LUNDATA_ATYP_EXTLUN 0xc0
|
|
};
|
|
|
|
struct scsi_report_luns_data {
|
|
u_int8_t length[4]; /* length of LUN inventory, in bytes */
|
|
u_int8_t reserved[4]; /* unused */
|
|
/*
|
|
* LUN inventory- we only support the type zero form for now.
|
|
*/
|
|
struct scsi_report_luns_lundata luns[0];
|
|
};
|
|
|
|
struct scsi_target_group
|
|
{
|
|
uint8_t opcode;
|
|
uint8_t service_action;
|
|
#define STG_PDF_LENGTH 0x00
|
|
#define RPL_PDF_EXTENDED 0x20
|
|
uint8_t reserved1[4];
|
|
uint8_t length[4];
|
|
uint8_t reserved2;
|
|
uint8_t control;
|
|
};
|
|
|
|
struct scsi_target_port_descriptor {
|
|
uint8_t reserved[2];
|
|
uint8_t relative_target_port_identifier[2];
|
|
uint8_t desc_list[];
|
|
};
|
|
|
|
struct scsi_target_port_group_descriptor {
|
|
uint8_t pref_state;
|
|
#define TPG_PRIMARY 0x80
|
|
#define TPG_ASYMMETRIC_ACCESS_STATE_MASK 0xf
|
|
#define TPG_ASYMMETRIC_ACCESS_OPTIMIZED 0x0
|
|
#define TPG_ASYMMETRIC_ACCESS_NONOPTIMIZED 0x1
|
|
#define TPG_ASYMMETRIC_ACCESS_STANDBY 0x2
|
|
#define TPG_ASYMMETRIC_ACCESS_UNAVAILABLE 0x3
|
|
#define TPG_ASYMMETRIC_ACCESS_LBA_DEPENDENT 0x4
|
|
#define TPG_ASYMMETRIC_ACCESS_OFFLINE 0xE
|
|
#define TPG_ASYMMETRIC_ACCESS_TRANSITIONING 0xF
|
|
uint8_t support;
|
|
#define TPG_AO_SUP 0x01
|
|
#define TPG_AN_SUP 0x02
|
|
#define TPG_S_SUP 0x04
|
|
#define TPG_U_SUP 0x08
|
|
#define TPG_LBD_SUP 0x10
|
|
#define TPG_O_SUP 0x40
|
|
#define TPG_T_SUP 0x80
|
|
uint8_t target_port_group[2];
|
|
uint8_t reserved;
|
|
uint8_t status;
|
|
#define TPG_UNAVLBL 0
|
|
#define TPG_SET_BY_STPG 0x01
|
|
#define TPG_IMPLICIT 0x02
|
|
uint8_t vendor_specific;
|
|
uint8_t target_port_count;
|
|
struct scsi_target_port_descriptor descriptors[];
|
|
};
|
|
|
|
struct scsi_target_group_data {
|
|
uint8_t length[4]; /* length of returned data, in bytes */
|
|
struct scsi_target_port_group_descriptor groups[];
|
|
};
|
|
|
|
struct scsi_target_group_data_extended {
|
|
uint8_t length[4]; /* length of returned data, in bytes */
|
|
uint8_t format_type; /* STG_PDF_LENGTH or RPL_PDF_EXTENDED */
|
|
uint8_t implicit_transition_time;
|
|
uint8_t reserved[2];
|
|
struct scsi_target_port_group_descriptor groups[];
|
|
};
|
|
|
|
|
|
typedef enum {
|
|
SSD_TYPE_NONE,
|
|
SSD_TYPE_FIXED,
|
|
SSD_TYPE_DESC
|
|
} scsi_sense_data_type;
|
|
|
|
typedef enum {
|
|
SSD_ELEM_NONE,
|
|
SSD_ELEM_SKIP,
|
|
SSD_ELEM_DESC,
|
|
SSD_ELEM_SKS,
|
|
SSD_ELEM_COMMAND,
|
|
SSD_ELEM_INFO,
|
|
SSD_ELEM_FRU,
|
|
SSD_ELEM_STREAM,
|
|
SSD_ELEM_MAX
|
|
} scsi_sense_elem_type;
|
|
|
|
|
|
struct scsi_sense_data
|
|
{
|
|
uint8_t error_code;
|
|
/*
|
|
* SPC-4 says that the maximum length of sense data is 252 bytes.
|
|
* So this structure is exactly 252 bytes log.
|
|
*/
|
|
#define SSD_FULL_SIZE 252
|
|
uint8_t sense_buf[SSD_FULL_SIZE - 1];
|
|
/*
|
|
* XXX KDM is this still a reasonable minimum size?
|
|
*/
|
|
#define SSD_MIN_SIZE 18
|
|
/*
|
|
* Maximum value for the extra_len field in the sense data.
|
|
*/
|
|
#define SSD_EXTRA_MAX 244
|
|
};
|
|
|
|
/*
|
|
* Fixed format sense data.
|
|
*/
|
|
struct scsi_sense_data_fixed
|
|
{
|
|
u_int8_t error_code;
|
|
#define SSD_ERRCODE 0x7F
|
|
#define SSD_CURRENT_ERROR 0x70
|
|
#define SSD_DEFERRED_ERROR 0x71
|
|
#define SSD_ERRCODE_VALID 0x80
|
|
u_int8_t segment;
|
|
u_int8_t flags;
|
|
#define SSD_KEY 0x0F
|
|
#define SSD_KEY_NO_SENSE 0x00
|
|
#define SSD_KEY_RECOVERED_ERROR 0x01
|
|
#define SSD_KEY_NOT_READY 0x02
|
|
#define SSD_KEY_MEDIUM_ERROR 0x03
|
|
#define SSD_KEY_HARDWARE_ERROR 0x04
|
|
#define SSD_KEY_ILLEGAL_REQUEST 0x05
|
|
#define SSD_KEY_UNIT_ATTENTION 0x06
|
|
#define SSD_KEY_DATA_PROTECT 0x07
|
|
#define SSD_KEY_BLANK_CHECK 0x08
|
|
#define SSD_KEY_Vendor_Specific 0x09
|
|
#define SSD_KEY_COPY_ABORTED 0x0a
|
|
#define SSD_KEY_ABORTED_COMMAND 0x0b
|
|
#define SSD_KEY_EQUAL 0x0c
|
|
#define SSD_KEY_VOLUME_OVERFLOW 0x0d
|
|
#define SSD_KEY_MISCOMPARE 0x0e
|
|
#define SSD_KEY_COMPLETED 0x0f
|
|
#define SSD_ILI 0x20
|
|
#define SSD_EOM 0x40
|
|
#define SSD_FILEMARK 0x80
|
|
u_int8_t info[4];
|
|
u_int8_t extra_len;
|
|
u_int8_t cmd_spec_info[4];
|
|
u_int8_t add_sense_code;
|
|
u_int8_t add_sense_code_qual;
|
|
u_int8_t fru;
|
|
u_int8_t sense_key_spec[3];
|
|
#define SSD_SCS_VALID 0x80
|
|
#define SSD_FIELDPTR_CMD 0x40
|
|
#define SSD_BITPTR_VALID 0x08
|
|
#define SSD_BITPTR_VALUE 0x07
|
|
u_int8_t extra_bytes[14];
|
|
#define SSD_FIXED_IS_PRESENT(sense, length, field) \
|
|
((length >= (offsetof(struct scsi_sense_data_fixed, field) + \
|
|
sizeof(sense->field))) ? 1 :0)
|
|
#define SSD_FIXED_IS_FILLED(sense, field) \
|
|
((((offsetof(struct scsi_sense_data_fixed, field) + \
|
|
sizeof(sense->field)) - \
|
|
(offsetof(struct scsi_sense_data_fixed, extra_len) + \
|
|
sizeof(sense->extra_len))) <= sense->extra_len) ? 1 : 0)
|
|
};
|
|
|
|
/*
|
|
* Descriptor format sense data definitions.
|
|
* Introduced in SPC-3.
|
|
*/
|
|
struct scsi_sense_data_desc
|
|
{
|
|
uint8_t error_code;
|
|
#define SSD_DESC_CURRENT_ERROR 0x72
|
|
#define SSD_DESC_DEFERRED_ERROR 0x73
|
|
uint8_t sense_key;
|
|
uint8_t add_sense_code;
|
|
uint8_t add_sense_code_qual;
|
|
uint8_t reserved[3];
|
|
/*
|
|
* Note that SPC-4, section 4.5.2.1 says that the extra_len field
|
|
* must be less than or equal to 244.
|
|
*/
|
|
uint8_t extra_len;
|
|
uint8_t sense_desc[0];
|
|
#define SSD_DESC_IS_PRESENT(sense, length, field) \
|
|
((length >= (offsetof(struct scsi_sense_data_desc, field) + \
|
|
sizeof(sense->field))) ? 1 :0)
|
|
};
|
|
|
|
struct scsi_sense_desc_header
|
|
{
|
|
uint8_t desc_type;
|
|
uint8_t length;
|
|
};
|
|
/*
|
|
* The information provide in the Information descriptor is device type or
|
|
* command specific information, and defined in a command standard.
|
|
*
|
|
* Note that any changes to the field names or positions in this structure,
|
|
* even reserved fields, should be accompanied by an examination of the
|
|
* code in ctl_set_sense() that uses them.
|
|
*
|
|
* Maximum descriptors allowed: 1 (as of SPC-4)
|
|
*/
|
|
struct scsi_sense_info
|
|
{
|
|
uint8_t desc_type;
|
|
#define SSD_DESC_INFO 0x00
|
|
uint8_t length;
|
|
uint8_t byte2;
|
|
#define SSD_INFO_VALID 0x80
|
|
uint8_t reserved;
|
|
uint8_t info[8];
|
|
};
|
|
|
|
/*
|
|
* Command-specific information depends on the command for which the
|
|
* reported condition occured.
|
|
*
|
|
* Note that any changes to the field names or positions in this structure,
|
|
* even reserved fields, should be accompanied by an examination of the
|
|
* code in ctl_set_sense() that uses them.
|
|
*
|
|
* Maximum descriptors allowed: 1 (as of SPC-4)
|
|
*/
|
|
struct scsi_sense_command
|
|
{
|
|
uint8_t desc_type;
|
|
#define SSD_DESC_COMMAND 0x01
|
|
uint8_t length;
|
|
uint8_t reserved[2];
|
|
uint8_t command_info[8];
|
|
};
|
|
|
|
/*
|
|
* Sense key specific descriptor. The sense key specific data format
|
|
* depends on the sense key in question.
|
|
*
|
|
* Maximum descriptors allowed: 1 (as of SPC-4)
|
|
*/
|
|
struct scsi_sense_sks
|
|
{
|
|
uint8_t desc_type;
|
|
#define SSD_DESC_SKS 0x02
|
|
uint8_t length;
|
|
uint8_t reserved1[2];
|
|
uint8_t sense_key_spec[3];
|
|
#define SSD_SKS_VALID 0x80
|
|
uint8_t reserved2;
|
|
};
|
|
|
|
/*
|
|
* This is used for the Illegal Request sense key (0x05) only.
|
|
*/
|
|
struct scsi_sense_sks_field
|
|
{
|
|
uint8_t byte0;
|
|
#define SSD_SKS_FIELD_VALID 0x80
|
|
#define SSD_SKS_FIELD_CMD 0x40
|
|
#define SSD_SKS_BPV 0x08
|
|
#define SSD_SKS_BIT_VALUE 0x07
|
|
uint8_t field[2];
|
|
};
|
|
|
|
|
|
/*
|
|
* This is used for the Hardware Error (0x04), Medium Error (0x03) and
|
|
* Recovered Error (0x01) sense keys.
|
|
*/
|
|
struct scsi_sense_sks_retry
|
|
{
|
|
uint8_t byte0;
|
|
#define SSD_SKS_RETRY_VALID 0x80
|
|
uint8_t actual_retry_count[2];
|
|
};
|
|
|
|
/*
|
|
* Used with the NO Sense (0x00) or Not Ready (0x02) sense keys.
|
|
*/
|
|
struct scsi_sense_sks_progress
|
|
{
|
|
uint8_t byte0;
|
|
#define SSD_SKS_PROGRESS_VALID 0x80
|
|
uint8_t progress[2];
|
|
#define SSD_SKS_PROGRESS_DENOM 0x10000
|
|
};
|
|
|
|
/*
|
|
* Used with the Copy Aborted (0x0a) sense key.
|
|
*/
|
|
struct scsi_sense_sks_segment
|
|
{
|
|
uint8_t byte0;
|
|
#define SSD_SKS_SEGMENT_VALID 0x80
|
|
#define SSD_SKS_SEGMENT_SD 0x20
|
|
#define SSD_SKS_SEGMENT_BPV 0x08
|
|
#define SSD_SKS_SEGMENT_BITPTR 0x07
|
|
uint8_t field[2];
|
|
};
|
|
|
|
/*
|
|
* Used with the Unit Attention (0x06) sense key.
|
|
*
|
|
* This is currently used to indicate that the unit attention condition
|
|
* queue has overflowed (when the overflow bit is set).
|
|
*/
|
|
struct scsi_sense_sks_overflow
|
|
{
|
|
uint8_t byte0;
|
|
#define SSD_SKS_OVERFLOW_VALID 0x80
|
|
#define SSD_SKS_OVERFLOW_SET 0x01
|
|
uint8_t reserved[2];
|
|
};
|
|
|
|
/*
|
|
* This specifies which component is associated with the sense data. There
|
|
* is no standard meaning for the fru value.
|
|
*
|
|
* Maximum descriptors allowed: 1 (as of SPC-4)
|
|
*/
|
|
struct scsi_sense_fru
|
|
{
|
|
uint8_t desc_type;
|
|
#define SSD_DESC_FRU 0x03
|
|
uint8_t length;
|
|
uint8_t reserved;
|
|
uint8_t fru;
|
|
};
|
|
|
|
/*
|
|
* Used for Stream commands, defined in SSC-4.
|
|
*
|
|
* Maximum descriptors allowed: 1 (as of SPC-4)
|
|
*/
|
|
|
|
struct scsi_sense_stream
|
|
{
|
|
uint8_t desc_type;
|
|
#define SSD_DESC_STREAM 0x04
|
|
uint8_t length;
|
|
uint8_t reserved;
|
|
uint8_t byte3;
|
|
#define SSD_DESC_STREAM_FM 0x80
|
|
#define SSD_DESC_STREAM_EOM 0x40
|
|
#define SSD_DESC_STREAM_ILI 0x20
|
|
};
|
|
|
|
/*
|
|
* Used for Block commands, defined in SBC-3.
|
|
*
|
|
* This is currently (as of SBC-3) only used for the Incorrect Length
|
|
* Indication (ILI) bit, which says that the data length requested in the
|
|
* READ LONG or WRITE LONG command did not match the length of the logical
|
|
* block.
|
|
*
|
|
* Maximum descriptors allowed: 1 (as of SPC-4)
|
|
*/
|
|
struct scsi_sense_block
|
|
{
|
|
uint8_t desc_type;
|
|
#define SSD_DESC_BLOCK 0x05
|
|
uint8_t length;
|
|
uint8_t reserved;
|
|
uint8_t byte3;
|
|
#define SSD_DESC_BLOCK_ILI 0x20
|
|
};
|
|
|
|
/*
|
|
* Used for Object-Based Storage Devices (OSD-3).
|
|
*
|
|
* Maximum descriptors allowed: 1 (as of SPC-4)
|
|
*/
|
|
struct scsi_sense_osd_objid
|
|
{
|
|
uint8_t desc_type;
|
|
#define SSD_DESC_OSD_OBJID 0x06
|
|
uint8_t length;
|
|
uint8_t reserved[6];
|
|
/*
|
|
* XXX KDM provide the bit definitions here? There are a lot of
|
|
* them, and we don't have an OSD driver yet.
|
|
*/
|
|
uint8_t not_init_cmds[4];
|
|
uint8_t completed_cmds[4];
|
|
uint8_t partition_id[8];
|
|
uint8_t object_id[8];
|
|
};
|
|
|
|
/*
|
|
* Used for Object-Based Storage Devices (OSD-3).
|
|
*
|
|
* Maximum descriptors allowed: 1 (as of SPC-4)
|
|
*/
|
|
struct scsi_sense_osd_integrity
|
|
{
|
|
uint8_t desc_type;
|
|
#define SSD_DESC_OSD_INTEGRITY 0x07
|
|
uint8_t length;
|
|
uint8_t integ_check_val[32];
|
|
};
|
|
|
|
/*
|
|
* Used for Object-Based Storage Devices (OSD-3).
|
|
*
|
|
* Maximum descriptors allowed: 1 (as of SPC-4)
|
|
*/
|
|
struct scsi_sense_osd_attr_id
|
|
{
|
|
uint8_t desc_type;
|
|
#define SSD_DESC_OSD_ATTR_ID 0x08
|
|
uint8_t length;
|
|
uint8_t reserved[2];
|
|
uint8_t attr_desc[0];
|
|
};
|
|
|
|
/*
|
|
* Used with Sense keys No Sense (0x00) and Not Ready (0x02).
|
|
*
|
|
* Maximum descriptors allowed: 32 (as of SPC-4)
|
|
*/
|
|
struct scsi_sense_progress
|
|
{
|
|
uint8_t desc_type;
|
|
#define SSD_DESC_PROGRESS 0x0a
|
|
uint8_t length;
|
|
uint8_t sense_key;
|
|
uint8_t add_sense_code;
|
|
uint8_t add_sense_code_qual;
|
|
uint8_t reserved;
|
|
uint8_t progress[2];
|
|
};
|
|
|
|
/*
|
|
* This is typically forwarded as the result of an EXTENDED COPY command.
|
|
*
|
|
* Maximum descriptors allowed: 2 (as of SPC-4)
|
|
*/
|
|
struct scsi_sense_forwarded
|
|
{
|
|
uint8_t desc_type;
|
|
#define SSD_DESC_FORWARDED 0x0c
|
|
uint8_t length;
|
|
uint8_t byte2;
|
|
#define SSD_FORWARDED_FSDT 0x80
|
|
#define SSD_FORWARDED_SDS_MASK 0x0f
|
|
#define SSD_FORWARDED_SDS_UNK 0x00
|
|
#define SSD_FORWARDED_SDS_EXSRC 0x01
|
|
#define SSD_FORWARDED_SDS_EXDST 0x02
|
|
};
|
|
|
|
/*
|
|
* Vendor-specific sense descriptor. The desc_type field will be in the
|
|
* range bewteen MIN and MAX inclusive.
|
|
*/
|
|
struct scsi_sense_vendor
|
|
{
|
|
uint8_t desc_type;
|
|
#define SSD_DESC_VENDOR_MIN 0x80
|
|
#define SSD_DESC_VENDOR_MAX 0xff
|
|
uint8_t length;
|
|
uint8_t data[0];
|
|
};
|
|
|
|
struct scsi_mode_header_6
|
|
{
|
|
u_int8_t data_length; /* Sense data length */
|
|
u_int8_t medium_type;
|
|
u_int8_t dev_spec;
|
|
u_int8_t blk_desc_len;
|
|
};
|
|
|
|
struct scsi_mode_header_10
|
|
{
|
|
u_int8_t data_length[2];/* Sense data length */
|
|
u_int8_t medium_type;
|
|
u_int8_t dev_spec;
|
|
u_int8_t unused[2];
|
|
u_int8_t blk_desc_len[2];
|
|
};
|
|
|
|
struct scsi_mode_page_header
|
|
{
|
|
u_int8_t page_code;
|
|
#define SMPH_PS 0x80
|
|
#define SMPH_SPF 0x40
|
|
#define SMPH_PC_MASK 0x3f
|
|
u_int8_t page_length;
|
|
};
|
|
|
|
struct scsi_mode_page_header_sp
|
|
{
|
|
uint8_t page_code;
|
|
uint8_t subpage;
|
|
uint8_t page_length[2];
|
|
};
|
|
|
|
|
|
struct scsi_mode_blk_desc
|
|
{
|
|
u_int8_t density;
|
|
u_int8_t nblocks[3];
|
|
u_int8_t reserved;
|
|
u_int8_t blklen[3];
|
|
};
|
|
|
|
#define SCSI_DEFAULT_DENSITY 0x00 /* use 'default' density */
|
|
#define SCSI_SAME_DENSITY 0x7f /* use 'same' density- >= SCSI-2 only */
|
|
|
|
|
|
/*
|
|
* Status Byte
|
|
*/
|
|
#define SCSI_STATUS_OK 0x00
|
|
#define SCSI_STATUS_CHECK_COND 0x02
|
|
#define SCSI_STATUS_COND_MET 0x04
|
|
#define SCSI_STATUS_BUSY 0x08
|
|
#define SCSI_STATUS_INTERMED 0x10
|
|
#define SCSI_STATUS_INTERMED_COND_MET 0x14
|
|
#define SCSI_STATUS_RESERV_CONFLICT 0x18
|
|
#define SCSI_STATUS_CMD_TERMINATED 0x22 /* Obsolete in SAM-2 */
|
|
#define SCSI_STATUS_QUEUE_FULL 0x28
|
|
#define SCSI_STATUS_ACA_ACTIVE 0x30
|
|
#define SCSI_STATUS_TASK_ABORTED 0x40
|
|
|
|
struct scsi_inquiry_pattern {
|
|
u_int8_t type;
|
|
u_int8_t media_type;
|
|
#define SIP_MEDIA_REMOVABLE 0x01
|
|
#define SIP_MEDIA_FIXED 0x02
|
|
const char *vendor;
|
|
const char *product;
|
|
const char *revision;
|
|
};
|
|
|
|
struct scsi_static_inquiry_pattern {
|
|
u_int8_t type;
|
|
u_int8_t media_type;
|
|
char vendor[SID_VENDOR_SIZE+1];
|
|
char product[SID_PRODUCT_SIZE+1];
|
|
char revision[SID_REVISION_SIZE+1];
|
|
};
|
|
|
|
struct scsi_sense_quirk_entry {
|
|
struct scsi_inquiry_pattern inq_pat;
|
|
int num_sense_keys;
|
|
int num_ascs;
|
|
struct sense_key_table_entry *sense_key_info;
|
|
struct asc_table_entry *asc_info;
|
|
};
|
|
|
|
struct sense_key_table_entry {
|
|
u_int8_t sense_key;
|
|
u_int32_t action;
|
|
const char *desc;
|
|
};
|
|
|
|
struct asc_table_entry {
|
|
u_int8_t asc;
|
|
u_int8_t ascq;
|
|
u_int32_t action;
|
|
const char *desc;
|
|
};
|
|
|
|
struct op_table_entry {
|
|
u_int8_t opcode;
|
|
u_int32_t opmask;
|
|
const char *desc;
|
|
};
|
|
|
|
struct scsi_op_quirk_entry {
|
|
struct scsi_inquiry_pattern inq_pat;
|
|
int num_ops;
|
|
struct op_table_entry *op_table;
|
|
};
|
|
|
|
typedef enum {
|
|
SSS_FLAG_NONE = 0x00,
|
|
SSS_FLAG_PRINT_COMMAND = 0x01
|
|
} scsi_sense_string_flags;
|
|
|
|
struct ccb_scsiio;
|
|
struct cam_periph;
|
|
union ccb;
|
|
#ifndef _KERNEL
|
|
struct cam_device;
|
|
#endif
|
|
|
|
extern const char *scsi_sense_key_text[];
|
|
|
|
struct sbuf;
|
|
|
|
__BEGIN_DECLS
|
|
void scsi_sense_desc(int sense_key, int asc, int ascq,
|
|
struct scsi_inquiry_data *inq_data,
|
|
const char **sense_key_desc, const char **asc_desc);
|
|
scsi_sense_action scsi_error_action(struct ccb_scsiio* csio,
|
|
struct scsi_inquiry_data *inq_data,
|
|
u_int32_t sense_flags);
|
|
const char * scsi_status_string(struct ccb_scsiio *csio);
|
|
|
|
void scsi_desc_iterate(struct scsi_sense_data_desc *sense, u_int sense_len,
|
|
int (*iter_func)(struct scsi_sense_data_desc *sense,
|
|
u_int, struct scsi_sense_desc_header *,
|
|
void *), void *arg);
|
|
uint8_t *scsi_find_desc(struct scsi_sense_data_desc *sense, u_int sense_len,
|
|
uint8_t desc_type);
|
|
void scsi_set_sense_data(struct scsi_sense_data *sense_data,
|
|
scsi_sense_data_type sense_format, int current_error,
|
|
int sense_key, int asc, int ascq, ...) ;
|
|
void scsi_set_sense_data_va(struct scsi_sense_data *sense_data,
|
|
scsi_sense_data_type sense_format,
|
|
int current_error, int sense_key, int asc,
|
|
int ascq, va_list ap);
|
|
int scsi_get_sense_info(struct scsi_sense_data *sense_data, u_int sense_len,
|
|
uint8_t info_type, uint64_t *info,
|
|
int64_t *signed_info);
|
|
int scsi_get_sks(struct scsi_sense_data *sense_data, u_int sense_len,
|
|
uint8_t *sks);
|
|
int scsi_get_block_info(struct scsi_sense_data *sense_data, u_int sense_len,
|
|
struct scsi_inquiry_data *inq_data,
|
|
uint8_t *block_bits);
|
|
int scsi_get_stream_info(struct scsi_sense_data *sense_data, u_int sense_len,
|
|
struct scsi_inquiry_data *inq_data,
|
|
uint8_t *stream_bits);
|
|
void scsi_info_sbuf(struct sbuf *sb, uint8_t *cdb, int cdb_len,
|
|
struct scsi_inquiry_data *inq_data, uint64_t info);
|
|
void scsi_command_sbuf(struct sbuf *sb, uint8_t *cdb, int cdb_len,
|
|
struct scsi_inquiry_data *inq_data, uint64_t csi);
|
|
void scsi_progress_sbuf(struct sbuf *sb, uint16_t progress);
|
|
int scsi_sks_sbuf(struct sbuf *sb, int sense_key, uint8_t *sks);
|
|
void scsi_fru_sbuf(struct sbuf *sb, uint64_t fru);
|
|
void scsi_stream_sbuf(struct sbuf *sb, uint8_t stream_bits, uint64_t info);
|
|
void scsi_block_sbuf(struct sbuf *sb, uint8_t block_bits, uint64_t info);
|
|
void scsi_sense_info_sbuf(struct sbuf *sb, struct scsi_sense_data *sense,
|
|
u_int sense_len, uint8_t *cdb, int cdb_len,
|
|
struct scsi_inquiry_data *inq_data,
|
|
struct scsi_sense_desc_header *header);
|
|
|
|
void scsi_sense_command_sbuf(struct sbuf *sb, struct scsi_sense_data *sense,
|
|
u_int sense_len, uint8_t *cdb, int cdb_len,
|
|
struct scsi_inquiry_data *inq_data,
|
|
struct scsi_sense_desc_header *header);
|
|
void scsi_sense_sks_sbuf(struct sbuf *sb, struct scsi_sense_data *sense,
|
|
u_int sense_len, uint8_t *cdb, int cdb_len,
|
|
struct scsi_inquiry_data *inq_data,
|
|
struct scsi_sense_desc_header *header);
|
|
void scsi_sense_fru_sbuf(struct sbuf *sb, struct scsi_sense_data *sense,
|
|
u_int sense_len, uint8_t *cdb, int cdb_len,
|
|
struct scsi_inquiry_data *inq_data,
|
|
struct scsi_sense_desc_header *header);
|
|
void scsi_sense_stream_sbuf(struct sbuf *sb, struct scsi_sense_data *sense,
|
|
u_int sense_len, uint8_t *cdb, int cdb_len,
|
|
struct scsi_inquiry_data *inq_data,
|
|
struct scsi_sense_desc_header *header);
|
|
void scsi_sense_block_sbuf(struct sbuf *sb, struct scsi_sense_data *sense,
|
|
u_int sense_len, uint8_t *cdb, int cdb_len,
|
|
struct scsi_inquiry_data *inq_data,
|
|
struct scsi_sense_desc_header *header);
|
|
void scsi_sense_progress_sbuf(struct sbuf *sb, struct scsi_sense_data *sense,
|
|
u_int sense_len, uint8_t *cdb, int cdb_len,
|
|
struct scsi_inquiry_data *inq_data,
|
|
struct scsi_sense_desc_header *header);
|
|
void scsi_sense_generic_sbuf(struct sbuf *sb, struct scsi_sense_data *sense,
|
|
u_int sense_len, uint8_t *cdb, int cdb_len,
|
|
struct scsi_inquiry_data *inq_data,
|
|
struct scsi_sense_desc_header *header);
|
|
void scsi_sense_desc_sbuf(struct sbuf *sb, struct scsi_sense_data *sense,
|
|
u_int sense_len, uint8_t *cdb, int cdb_len,
|
|
struct scsi_inquiry_data *inq_data,
|
|
struct scsi_sense_desc_header *header);
|
|
scsi_sense_data_type scsi_sense_type(struct scsi_sense_data *sense_data);
|
|
|
|
void scsi_sense_only_sbuf(struct scsi_sense_data *sense, u_int sense_len,
|
|
struct sbuf *sb, char *path_str,
|
|
struct scsi_inquiry_data *inq_data, uint8_t *cdb,
|
|
int cdb_len);
|
|
|
|
#ifdef _KERNEL
|
|
int scsi_command_string(struct ccb_scsiio *csio, struct sbuf *sb);
|
|
int scsi_sense_sbuf(struct ccb_scsiio *csio, struct sbuf *sb,
|
|
scsi_sense_string_flags flags);
|
|
char * scsi_sense_string(struct ccb_scsiio *csio,
|
|
char *str, int str_len);
|
|
void scsi_sense_print(struct ccb_scsiio *csio);
|
|
#else /* _KERNEL */
|
|
int scsi_command_string(struct cam_device *device,
|
|
struct ccb_scsiio *csio, struct sbuf *sb);
|
|
int scsi_sense_sbuf(struct cam_device *device,
|
|
struct ccb_scsiio *csio, struct sbuf *sb,
|
|
scsi_sense_string_flags flags);
|
|
char * scsi_sense_string(struct cam_device *device,
|
|
struct ccb_scsiio *csio,
|
|
char *str, int str_len);
|
|
void scsi_sense_print(struct cam_device *device,
|
|
struct ccb_scsiio *csio, FILE *ofile);
|
|
#endif /* _KERNEL */
|
|
|
|
const char * scsi_op_desc(u_int16_t opcode,
|
|
struct scsi_inquiry_data *inq_data);
|
|
char * scsi_cdb_string(u_int8_t *cdb_ptr, char *cdb_string,
|
|
size_t len);
|
|
|
|
void scsi_print_inquiry(struct scsi_inquiry_data *inq_data);
|
|
|
|
u_int scsi_calc_syncsrate(u_int period_factor);
|
|
u_int scsi_calc_syncparam(u_int period);
|
|
|
|
typedef int (*scsi_devid_checkfn_t)(uint8_t *);
|
|
int scsi_devid_is_naa_ieee_reg(uint8_t *bufp);
|
|
int scsi_devid_is_sas_target(uint8_t *bufp);
|
|
uint8_t * scsi_get_devid(struct scsi_vpd_device_id *id, uint32_t len,
|
|
scsi_devid_checkfn_t ck_fn);
|
|
|
|
void scsi_test_unit_ready(struct ccb_scsiio *csio, u_int32_t retries,
|
|
void (*cbfcnp)(struct cam_periph *,
|
|
union ccb *),
|
|
u_int8_t tag_action,
|
|
u_int8_t sense_len, u_int32_t timeout);
|
|
|
|
void scsi_request_sense(struct ccb_scsiio *csio, u_int32_t retries,
|
|
void (*cbfcnp)(struct cam_periph *,
|
|
union ccb *),
|
|
void *data_ptr, u_int8_t dxfer_len,
|
|
u_int8_t tag_action, u_int8_t sense_len,
|
|
u_int32_t timeout);
|
|
|
|
void scsi_inquiry(struct ccb_scsiio *csio, u_int32_t retries,
|
|
void (*cbfcnp)(struct cam_periph *, union ccb *),
|
|
u_int8_t tag_action, u_int8_t *inq_buf,
|
|
u_int32_t inq_len, int evpd, u_int8_t page_code,
|
|
u_int8_t sense_len, u_int32_t timeout);
|
|
|
|
void scsi_mode_sense(struct ccb_scsiio *csio, u_int32_t retries,
|
|
void (*cbfcnp)(struct cam_periph *,
|
|
union ccb *),
|
|
u_int8_t tag_action, int dbd,
|
|
u_int8_t page_code, u_int8_t page,
|
|
u_int8_t *param_buf, u_int32_t param_len,
|
|
u_int8_t sense_len, u_int32_t timeout);
|
|
|
|
void scsi_mode_sense_len(struct ccb_scsiio *csio, u_int32_t retries,
|
|
void (*cbfcnp)(struct cam_periph *,
|
|
union ccb *),
|
|
u_int8_t tag_action, int dbd,
|
|
u_int8_t page_code, u_int8_t page,
|
|
u_int8_t *param_buf, u_int32_t param_len,
|
|
int minimum_cmd_size, u_int8_t sense_len,
|
|
u_int32_t timeout);
|
|
|
|
void scsi_mode_select(struct ccb_scsiio *csio, u_int32_t retries,
|
|
void (*cbfcnp)(struct cam_periph *,
|
|
union ccb *),
|
|
u_int8_t tag_action, int scsi_page_fmt,
|
|
int save_pages, u_int8_t *param_buf,
|
|
u_int32_t param_len, u_int8_t sense_len,
|
|
u_int32_t timeout);
|
|
|
|
void scsi_mode_select_len(struct ccb_scsiio *csio, u_int32_t retries,
|
|
void (*cbfcnp)(struct cam_periph *,
|
|
union ccb *),
|
|
u_int8_t tag_action, int scsi_page_fmt,
|
|
int save_pages, u_int8_t *param_buf,
|
|
u_int32_t param_len, int minimum_cmd_size,
|
|
u_int8_t sense_len, u_int32_t timeout);
|
|
|
|
void scsi_log_sense(struct ccb_scsiio *csio, u_int32_t retries,
|
|
void (*cbfcnp)(struct cam_periph *, union ccb *),
|
|
u_int8_t tag_action, u_int8_t page_code,
|
|
u_int8_t page, int save_pages, int ppc,
|
|
u_int32_t paramptr, u_int8_t *param_buf,
|
|
u_int32_t param_len, u_int8_t sense_len,
|
|
u_int32_t timeout);
|
|
|
|
void scsi_log_select(struct ccb_scsiio *csio, u_int32_t retries,
|
|
void (*cbfcnp)(struct cam_periph *,
|
|
union ccb *), u_int8_t tag_action,
|
|
u_int8_t page_code, int save_pages,
|
|
int pc_reset, u_int8_t *param_buf,
|
|
u_int32_t param_len, u_int8_t sense_len,
|
|
u_int32_t timeout);
|
|
|
|
void scsi_prevent(struct ccb_scsiio *csio, u_int32_t retries,
|
|
void (*cbfcnp)(struct cam_periph *, union ccb *),
|
|
u_int8_t tag_action, u_int8_t action,
|
|
u_int8_t sense_len, u_int32_t timeout);
|
|
|
|
void scsi_read_capacity(struct ccb_scsiio *csio, u_int32_t retries,
|
|
void (*cbfcnp)(struct cam_periph *,
|
|
union ccb *), u_int8_t tag_action,
|
|
struct scsi_read_capacity_data *,
|
|
u_int8_t sense_len, u_int32_t timeout);
|
|
void scsi_read_capacity_16(struct ccb_scsiio *csio, uint32_t retries,
|
|
void (*cbfcnp)(struct cam_periph *,
|
|
union ccb *), uint8_t tag_action,
|
|
uint64_t lba, int reladr, int pmi,
|
|
uint8_t *rcap_buf, int rcap_buf_len,
|
|
uint8_t sense_len, uint32_t timeout);
|
|
|
|
void scsi_report_luns(struct ccb_scsiio *csio, u_int32_t retries,
|
|
void (*cbfcnp)(struct cam_periph *,
|
|
union ccb *), u_int8_t tag_action,
|
|
u_int8_t select_report,
|
|
struct scsi_report_luns_data *rpl_buf,
|
|
u_int32_t alloc_len, u_int8_t sense_len,
|
|
u_int32_t timeout);
|
|
|
|
void scsi_report_target_group(struct ccb_scsiio *csio, u_int32_t retries,
|
|
void (*cbfcnp)(struct cam_periph *,
|
|
union ccb *), u_int8_t tag_action,
|
|
u_int8_t pdf,
|
|
void *buf,
|
|
u_int32_t alloc_len, u_int8_t sense_len,
|
|
u_int32_t timeout);
|
|
|
|
void scsi_set_target_group(struct ccb_scsiio *csio, u_int32_t retries,
|
|
void (*cbfcnp)(struct cam_periph *,
|
|
union ccb *), u_int8_t tag_action, void *buf,
|
|
u_int32_t alloc_len, u_int8_t sense_len,
|
|
u_int32_t timeout);
|
|
|
|
void scsi_synchronize_cache(struct ccb_scsiio *csio,
|
|
u_int32_t retries,
|
|
void (*cbfcnp)(struct cam_periph *,
|
|
union ccb *), u_int8_t tag_action,
|
|
u_int32_t begin_lba, u_int16_t lb_count,
|
|
u_int8_t sense_len, u_int32_t timeout);
|
|
|
|
void scsi_receive_diagnostic_results(struct ccb_scsiio *csio, u_int32_t retries,
|
|
void (*cbfcnp)(struct cam_periph *,
|
|
union ccb*),
|
|
uint8_t tag_action, int pcv,
|
|
uint8_t page_code, uint8_t *data_ptr,
|
|
uint16_t allocation_length,
|
|
uint8_t sense_len, uint32_t timeout);
|
|
|
|
void scsi_send_diagnostic(struct ccb_scsiio *csio, u_int32_t retries,
|
|
void (*cbfcnp)(struct cam_periph *, union ccb *),
|
|
uint8_t tag_action, int unit_offline,
|
|
int device_offline, int self_test, int page_format,
|
|
int self_test_code, uint8_t *data_ptr,
|
|
uint16_t param_list_length, uint8_t sense_len,
|
|
uint32_t timeout);
|
|
|
|
void scsi_read_buffer(struct ccb_scsiio *csio, u_int32_t retries,
|
|
void (*cbfcnp)(struct cam_periph *, union ccb*),
|
|
uint8_t tag_action, int mode,
|
|
uint8_t buffer_id, u_int32_t offset,
|
|
uint8_t *data_ptr, uint32_t allocation_length,
|
|
uint8_t sense_len, uint32_t timeout);
|
|
|
|
void scsi_write_buffer(struct ccb_scsiio *csio, u_int32_t retries,
|
|
void (*cbfcnp)(struct cam_periph *, union ccb *),
|
|
uint8_t tag_action, int mode,
|
|
uint8_t buffer_id, u_int32_t offset,
|
|
uint8_t *data_ptr, uint32_t param_list_length,
|
|
uint8_t sense_len, uint32_t timeout);
|
|
|
|
#define SCSI_RW_READ 0x0001
|
|
#define SCSI_RW_WRITE 0x0002
|
|
#define SCSI_RW_DIRMASK 0x0003
|
|
#define SCSI_RW_BIO 0x1000
|
|
void scsi_read_write(struct ccb_scsiio *csio, u_int32_t retries,
|
|
void (*cbfcnp)(struct cam_periph *, union ccb *),
|
|
u_int8_t tag_action, int readop, u_int8_t byte2,
|
|
int minimum_cmd_size, u_int64_t lba,
|
|
u_int32_t block_count, u_int8_t *data_ptr,
|
|
u_int32_t dxfer_len, u_int8_t sense_len,
|
|
u_int32_t timeout);
|
|
|
|
void scsi_write_same(struct ccb_scsiio *csio, u_int32_t retries,
|
|
void (*cbfcnp)(struct cam_periph *, union ccb *),
|
|
u_int8_t tag_action, u_int8_t byte2,
|
|
int minimum_cmd_size, u_int64_t lba,
|
|
u_int32_t block_count, u_int8_t *data_ptr,
|
|
u_int32_t dxfer_len, u_int8_t sense_len,
|
|
u_int32_t timeout);
|
|
|
|
void scsi_unmap(struct ccb_scsiio *csio, u_int32_t retries,
|
|
void (*cbfcnp)(struct cam_periph *, union ccb *),
|
|
u_int8_t tag_action, u_int8_t byte2,
|
|
u_int8_t *data_ptr, u_int16_t dxfer_len,
|
|
u_int8_t sense_len, u_int32_t timeout);
|
|
|
|
void scsi_start_stop(struct ccb_scsiio *csio, u_int32_t retries,
|
|
void (*cbfcnp)(struct cam_periph *, union ccb *),
|
|
u_int8_t tag_action, int start, int load_eject,
|
|
int immediate, u_int8_t sense_len, u_int32_t timeout);
|
|
|
|
int scsi_inquiry_match(caddr_t inqbuffer, caddr_t table_entry);
|
|
int scsi_static_inquiry_match(caddr_t inqbuffer,
|
|
caddr_t table_entry);
|
|
int scsi_devid_match(uint8_t *rhs, size_t rhs_len,
|
|
uint8_t *lhs, size_t lhs_len);
|
|
|
|
void scsi_extract_sense(struct scsi_sense_data *sense, int *error_code,
|
|
int *sense_key, int *asc, int *ascq);
|
|
int scsi_extract_sense_ccb(union ccb *ccb, int *error_code, int *sense_key,
|
|
int *asc, int *ascq);
|
|
void scsi_extract_sense_len(struct scsi_sense_data *sense,
|
|
u_int sense_len, int *error_code, int *sense_key,
|
|
int *asc, int *ascq, int show_errors);
|
|
int scsi_get_sense_key(struct scsi_sense_data *sense, u_int sense_len,
|
|
int show_errors);
|
|
int scsi_get_asc(struct scsi_sense_data *sense, u_int sense_len,
|
|
int show_errors);
|
|
int scsi_get_ascq(struct scsi_sense_data *sense, u_int sense_len,
|
|
int show_errors);
|
|
static __inline void scsi_ulto2b(u_int32_t val, u_int8_t *bytes);
|
|
static __inline void scsi_ulto3b(u_int32_t val, u_int8_t *bytes);
|
|
static __inline void scsi_ulto4b(u_int32_t val, u_int8_t *bytes);
|
|
static __inline void scsi_u64to8b(u_int64_t val, u_int8_t *bytes);
|
|
static __inline uint32_t scsi_2btoul(const uint8_t *bytes);
|
|
static __inline uint32_t scsi_3btoul(const uint8_t *bytes);
|
|
static __inline int32_t scsi_3btol(const uint8_t *bytes);
|
|
static __inline uint32_t scsi_4btoul(const uint8_t *bytes);
|
|
static __inline uint64_t scsi_8btou64(const uint8_t *bytes);
|
|
static __inline void *find_mode_page_6(struct scsi_mode_header_6 *mode_header);
|
|
static __inline void *find_mode_page_10(struct scsi_mode_header_10 *mode_header);
|
|
|
|
static __inline void
|
|
scsi_ulto2b(u_int32_t val, u_int8_t *bytes)
|
|
{
|
|
|
|
bytes[0] = (val >> 8) & 0xff;
|
|
bytes[1] = val & 0xff;
|
|
}
|
|
|
|
static __inline void
|
|
scsi_ulto3b(u_int32_t val, u_int8_t *bytes)
|
|
{
|
|
|
|
bytes[0] = (val >> 16) & 0xff;
|
|
bytes[1] = (val >> 8) & 0xff;
|
|
bytes[2] = val & 0xff;
|
|
}
|
|
|
|
static __inline void
|
|
scsi_ulto4b(u_int32_t val, u_int8_t *bytes)
|
|
{
|
|
|
|
bytes[0] = (val >> 24) & 0xff;
|
|
bytes[1] = (val >> 16) & 0xff;
|
|
bytes[2] = (val >> 8) & 0xff;
|
|
bytes[3] = val & 0xff;
|
|
}
|
|
|
|
static __inline void
|
|
scsi_u64to8b(u_int64_t val, u_int8_t *bytes)
|
|
{
|
|
|
|
bytes[0] = (val >> 56) & 0xff;
|
|
bytes[1] = (val >> 48) & 0xff;
|
|
bytes[2] = (val >> 40) & 0xff;
|
|
bytes[3] = (val >> 32) & 0xff;
|
|
bytes[4] = (val >> 24) & 0xff;
|
|
bytes[5] = (val >> 16) & 0xff;
|
|
bytes[6] = (val >> 8) & 0xff;
|
|
bytes[7] = val & 0xff;
|
|
}
|
|
|
|
static __inline uint32_t
|
|
scsi_2btoul(const uint8_t *bytes)
|
|
{
|
|
uint32_t rv;
|
|
|
|
rv = (bytes[0] << 8) |
|
|
bytes[1];
|
|
return (rv);
|
|
}
|
|
|
|
static __inline uint32_t
|
|
scsi_3btoul(const uint8_t *bytes)
|
|
{
|
|
uint32_t rv;
|
|
|
|
rv = (bytes[0] << 16) |
|
|
(bytes[1] << 8) |
|
|
bytes[2];
|
|
return (rv);
|
|
}
|
|
|
|
static __inline int32_t
|
|
scsi_3btol(const uint8_t *bytes)
|
|
{
|
|
uint32_t rc = scsi_3btoul(bytes);
|
|
|
|
if (rc & 0x00800000)
|
|
rc |= 0xff000000;
|
|
|
|
return (int32_t) rc;
|
|
}
|
|
|
|
static __inline uint32_t
|
|
scsi_4btoul(const uint8_t *bytes)
|
|
{
|
|
uint32_t rv;
|
|
|
|
rv = (bytes[0] << 24) |
|
|
(bytes[1] << 16) |
|
|
(bytes[2] << 8) |
|
|
bytes[3];
|
|
return (rv);
|
|
}
|
|
|
|
static __inline uint64_t
|
|
scsi_8btou64(const uint8_t *bytes)
|
|
{
|
|
uint64_t rv;
|
|
|
|
rv = (((uint64_t)bytes[0]) << 56) |
|
|
(((uint64_t)bytes[1]) << 48) |
|
|
(((uint64_t)bytes[2]) << 40) |
|
|
(((uint64_t)bytes[3]) << 32) |
|
|
(((uint64_t)bytes[4]) << 24) |
|
|
(((uint64_t)bytes[5]) << 16) |
|
|
(((uint64_t)bytes[6]) << 8) |
|
|
bytes[7];
|
|
return (rv);
|
|
}
|
|
|
|
/*
|
|
* Given the pointer to a returned mode sense buffer, return a pointer to
|
|
* the start of the first mode page.
|
|
*/
|
|
static __inline void *
|
|
find_mode_page_6(struct scsi_mode_header_6 *mode_header)
|
|
{
|
|
void *page_start;
|
|
|
|
page_start = (void *)((u_int8_t *)&mode_header[1] +
|
|
mode_header->blk_desc_len);
|
|
|
|
return(page_start);
|
|
}
|
|
|
|
static __inline void *
|
|
find_mode_page_10(struct scsi_mode_header_10 *mode_header)
|
|
{
|
|
void *page_start;
|
|
|
|
page_start = (void *)((u_int8_t *)&mode_header[1] +
|
|
scsi_2btoul(mode_header->blk_desc_len));
|
|
|
|
return(page_start);
|
|
}
|
|
|
|
__END_DECLS
|
|
|
|
#endif /*_SCSI_SCSI_ALL_H*/
|