d/freebsd-skq
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
fe5871fb09
freebsd-skq/sys/dev/aha/ahareg.h
Warner Losh 07353d4247 o enable plug and play support for the aha driver. Given the cumbersome 
pnp system in freebsd, I'm not sure how useful this will be, but my
  1542CP seems to work well in plug and play mode and does seem to
  probe correctly at all the oddball addresses/irq/drqs that I tried.
  [[
     I was unable to get /kernel.conf or /kernel.config to read in, so
     I wasn't able to verify that this method of userconfig works.  that's
     one thing that makes pnp so hard to use in the current scheme.
     Pointers to the right new way of doing this accepted.
  ]]
o Add some kludges to maybe bring support for 1540A/1542A into the
  driver.  Since I have no 154xA cards, and the only person I know
  that has them hasn't given me feedback, I'm making this commit
  blind.
o Honor unit numbers that are in the config file now.  This allows one
  to hard wire the unit numbers (and have high unit numbers for plug
  and pray devices, which can't seem to be hardwired) and have the
  cards not migrate from aha1 -> aha0 should aha0 go on the fritz.  I
  didn't verify that hard wired scsi busses would work, but did verify
  that hard wired aha addresses did work to a limited extent.  Both
  aha0 and aha1 must be hardwired, or when the card that was in aha0
  goes away, the probe for aha0 might pick up the card that otherwise
  would have been aha1.
1999-01-20 06:21:27 +00:00

448 lines
12 KiB
C
Raw Blame History

/*
* Generic register and struct definitions for the Adaptech 154x/164x
* SCSI host adapters. Product specific probe and attach routines can
* be found in:
* <fill in list here>
*
* Derived from bt.c written by:
*
* Copyright (c) 1998 Justin T. Gibbs.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions, and the following disclaimer,
* without modification, immediately at the beginning of the file.
* 2. The name of the author may not be used to endorse or promote products
* derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* $Id: ahareg.h,v 1.4 1998/11/10 06:44:42 gibbs Exp $
*/
#ifndef _AHAREG_H_
#define _AHAREG_H_
#include "aha.h"
#include <sys/queue.h>
#include <cam/scsi/scsi_all.h>
#define AHA_MAXTRANSFER_SIZE 0xffffff /* limited by 24bit counter */
#define AHA_NSEG 17 /* The number of dma segments
* supported. */
#define ALL_TARGETS (~0)
/*
* Control Register pp. 1-8, 1-9 (Write Only)
*/
#define CONTROL_REG 0x00
#define HARD_RESET 0x80 /* Hard Reset - return to POST state */
#define SOFT_RESET 0x40 /* Soft Reset - Clears Adapter state */
#define RESET_INTR 0x20 /* Reset/Ack Interrupt */
#define RESET_SBUS 0x10 /* Drive SCSI bus reset signal */
/*
* Status Register pp. 1-9, 1-10 (Read Only)
*/
#define STATUS_REG 0x00
#define DIAG_ACTIVE 0x80 /* Performing Internal Diags */
#define DIAG_FAIL 0x40 /* Internal Diags failed */
#define INIT_REQUIRED 0x20 /* MBOXes need initialization */
#define HA_READY 0x10 /* HA ready for new commands */
#define CMD_REG_BUSY 0x08 /* HA busy with last cmd byte */
#define DATAIN_REG_READY 0x04 /* Data-in Byte available */
#define STATUS_REG_RSVD 0x02
#define CMD_INVALID 0x01 /* Invalid Command detected */
/*
* Command/Parameter Register pp. 1-10, 1-11 (Write Only)
*/
#define COMMAND_REG 0x01
/*
* Data in Register p. 1-11 (Read Only)
*/
#define DATAIN_REG 0x01
/*
* Interrupt Status Register pp. 1-12 -> 1-14 (Read Only)
*/
#define INTSTAT_REG 0x02
#define INTR_PENDING 0x80 /* There is a pending INTR */
#define INTSTAT_REG_RSVD 0x70
#define SCSI_BUS_RESET 0x08 /* Bus Reset detected */
#define CMD_COMPLETE 0x04
#define OMB_READY 0x02 /* Outgoin Mailbox Ready */
#define IMB_LOADED 0x01 /* Incoming Mailbox loaded */
/*
* Definitions for the "undocumented" geometry register, we just need
* its location.
*/
#define GEOMETRY_REG 0x03
#define AHA_NREGS (4)
/*
* Opcodes for Adapter commands.
*/
typedef enum {
AOP_NOP = 0x00,
AOP_INITIALIZE_MBOX = 0x01,
AOP_START_MBOX = 0x02,
AOP_EXECUTE_BIOS_CMD = 0x03,
AOP_INQUIRE_BOARD_ID = 0x04,
AOP_ENABLE_OMBR_INT = 0x05,
AOP_SET_SEL_TIMOUT = 0x06,
AOP_SET_TIME_ON_BUS = 0x07,
AOP_SET_TIME_OFF_BUS = 0x08,
AOP_SET_BUS_TRANS_RATE = 0x09,
AOP_INQUIRE_INST_LDEVS = 0x0A,
AOP_INQUIRE_CONFIG = 0x0B,
AOP_ENABLE_TARGET_MODE = 0x0C,
AOP_INQUIRE_SETUP_INFO = 0x0D,
AOP_WRITE_LRAM = 0x1A,
AOP_READ_LRAM = 0x1B,
AOP_WRITE_CHIP_FIFO = 0x1C,
AOP_READ_CHIP_FIFO = 0x1D,
AOP_ECHO_DATA_BYTE = 0x1F,
AOP_ADAPTER_DIAGNOSTICS = 0x20,
AOP_SET_ADAPTER_OPTIONS = 0x21,
AOP_SET_EEPROM = 0x22,
AOP_RETURN_EEPROM = 0x23,
AOP_ENABLE_SHADOW_RAM = 0x24,
AOP_INIT_BIOS_MBOX = 0x25,
AOP_SET_BIOS_BANK_1 = 0x26,
AOP_SET_BIOS_BANK_2 = 0x27,
AOP_RETURN_EXT_BIOS_INFO= 0x28,
AOP_MBOX_IF_ENABLE = 0x29,
AOP_SCSI_TERM_STATUS = 0x2C,
AOP_INQUIRE_SCAM_DEV = 0x2D,
AOP_SCSI_DEV_TABLE = 0x2E,
AOP_SCAM_OP = 0x2F,
AOP_START_BIOS_CMD = 0x82,
AOP_INQUIRE_ESETUP_INFO = 0x8D
} aha_op_t;
/************** Definitions of Multi-byte commands and responses ************/
struct aha_extbios
{
u_int8_t flags; /* Bit 3 == 1 extended bios enabled */
u_int8_t mailboxlock; /* mail box lock code to unlock it */
};
typedef struct {
u_int8_t num_mboxes;
u_int8_t base_addr[3];
} init_24b_mbox_params_t;
typedef struct {
u_int8_t board_type;
/* These values are mostly from the aha-1540CP technical reference, but */
/* with other values from the old aha1542.c driver. The values from the */
/* aha-1540CP technical manual are used where conflicts arise */
#define BOARD_1540_16HEAD_BIOS 0x00
#define BOARD_1540_64HEAD_BIOS 0x30
#define BOARD_1542 0x41 /* aha-1540/1542 w/64-h bios */
#define BOARD_1640 0x42 /* aha-1640 */
#define BOARD_1740 0x43 /* aha-1740A/1742A/1744 */
#define BOARD_1542C 0x44 /* aha-1542C */
#define BOARD_1542CF 0x45 /* aha-1542CF */
#define BOARD_1542CP 0x46 /* aha-1542CP, plug and play */
u_int8_t cust_features;
#define FEATURES_STANDARD 0x30
u_int8_t firmware_rev_major;
u_int8_t firmware_rev_minor;
} board_id_data_t;
typedef struct {
u_int8_t dma_chan;
#define DMA_CHAN_5 0x20
#define DMA_CHAN_6 0x40
#define DMA_CHAN_7 0x80
u_int8_t irq;
#define IRQ_9 0x01
#define IRQ_10 0x02
#define IRQ_11 0x04
#define IRQ_12 0x08
#define IRQ_14 0x20
#define IRQ_15 0x40
u_int8_t scsi_id;
} config_data_t;
typedef struct {
u_int8_t enable;
} target_mode_params_t;
typedef struct {
u_int8_t offset : 4,
period : 3,
sync : 1;
} targ_syncinfo_t;
typedef struct {
u_int8_t initiate_sync : 1,
parity_enable : 1,
: 6;
u_int8_t bus_transfer_rate;
u_int8_t time_on_bus;
u_int8_t time_off_bus;
u_int8_t num_mboxes;
u_int8_t mbox_base_addr[3];
targ_syncinfo_t syncinfo[8];
u_int8_t discinfo;
u_int8_t customer_sig[20];
u_int8_t auto_retry;
u_int8_t board_switches;
u_int8_t firmware_cksum[2];
u_int8_t bios_mbox_addr[3];
} setup_data_t;
struct aha_isa_port {
u_int16_t addr;
u_int8_t probed;
u_int8_t bio; /* board IO offset */
};
#define AHA_NUM_ISAPORTS 6
typedef enum {
BIO_330 = 0,
BIO_334 = 1,
BIO_230 = 2,
BIO_234 = 3,
BIO_130 = 4,
BIO_134 = 5,
BIO_DISABLED = 6,
BIO_DISABLED2 = 7
} isa_compat_io_t;
typedef struct {
u_int8_t sync_rate[16]; /* Sync in 10ns units */
} target_sync_info_data_t;
typedef struct {
u_int8_t len[3];
u_int8_t addr[3];
} aha_sg_t;
/********************** Mail Box definitions *******************************/
typedef enum {
AMBO_FREE = 0x0, /* MBO intry is free */
AMBO_START = 0x1, /* MBO activate entry */
AMBO_ABORT = 0x2 /* MBO abort entry */
} aha_mbo_action_code_t;
typedef struct aha_mbox_out {
u_int8_t action_code;
u_int8_t ccb_addr[3];
} aha_mbox_out_t;
typedef enum {
AMBI_FREE = 0x0, /* MBI entry is free */
AMBI_OK = 0x1, /* completed without error */
AMBI_ABORT = 0x2, /* aborted ccb */
AMBI_NOT_FOUND = 0x3, /* Tried to abort invalid CCB */
AMBI_ERROR = 0x4 /* Completed with error */
} aha_mbi_comp_code_t;
typedef struct aha_mbox_in {
u_int8_t comp_code;
u_int8_t ccb_addr[3];
} aha_mbox_in_t;
/****************** Hardware CCB definition *********************************/
typedef enum {
INITIATOR_CCB = 0x00,
INITIATOR_SG_CCB = 0x02,
INITIATOR_CCB_WRESID = 0x03,
INITIATOR_SG_CCB_WRESID = 0x04,
INITIATOR_BUS_DEV_RESET = 0x81
} aha_ccb_opcode_t;
typedef enum {
AHASTAT_NOERROR = 0x00,
AHASTAT_SELTIMEOUT = 0x11,
AHASTAT_DATARUN_ERROR = 0x12,
AHASTAT_UNEXPECTED_BUSFREE = 0x13,
AHASTAT_INVALID_PHASE = 0x14,
AHASTAT_INVALID_ACTION_CODE = 0x15,
AHASTAT_INVALID_OPCODE = 0x16,
AHASTAT_LINKED_CCB_LUN_MISMATCH = 0x17,
AHASTAT_INVALID_CCB_OR_SG_PARAM = 0x1A,
AHASTAT_HA_SCSI_BUS_RESET = 0x22, /* stolen from bt */
AHASTAT_HA_BDR = 0x25 /* Stolen from bt */
} ahastat_t;
struct aha_hccb {
u_int8_t opcode; /* 0 */
u_int8_t lun : 3, /* 1 */
datain : 1,
dataout : 1,
target : 3;
u_int8_t cmd_len; /* 2 */
u_int8_t sense_len; /* 3 */
u_int8_t data_len[3]; /* 4 */
u_int8_t data_addr[3]; /* 7 */
u_int8_t link_ptr[3]; /* 10 */
u_int8_t link_id; /* 13 */
u_int8_t ahastat; /* 14 */
u_int8_t sdstat; /* 15 */
u_int8_t reserved1; /* 16 */
u_int8_t reserved2; /* 17 */
u_int8_t scsi_cdb[16]; /* 18 */
u_int8_t sense_data[SSD_FULL_SIZE];
};
typedef enum {
ACCB_FREE = 0x0,
ACCB_ACTIVE = 0x1,
ACCB_DEVICE_RESET = 0x2,
ACCB_RELEASE_SIMQ = 0x4
} accb_flags_t;
struct aha_ccb {
struct aha_hccb hccb; /* hccb assumed to be at 0 */
SLIST_ENTRY(aha_ccb) links;
u_int32_t flags;
union ccb *ccb;
bus_dmamap_t dmamap;
aha_sg_t *sg_list;
u_int32_t sg_list_phys;
};
struct sg_map_node {
bus_dmamap_t sg_dmamap;
bus_addr_t sg_physaddr;
aha_sg_t* sg_vaddr;
SLIST_ENTRY(sg_map_node) links;
};
struct aha_softc {
bus_space_tag_t tag;
bus_space_handle_t bsh;
struct cam_sim *sim;
struct cam_path *path;
aha_mbox_out_t *cur_outbox;
aha_mbox_in_t *cur_inbox;
aha_mbox_out_t *last_outbox;
aha_mbox_in_t *last_inbox;
struct aha_ccb *aha_ccb_array;
SLIST_HEAD(,aha_ccb) free_aha_ccbs;
LIST_HEAD(,ccb_hdr) pending_ccbs;
u_int active_ccbs;
u_int32_t aha_ccb_physbase;
aha_ccb_opcode_t ccb_sg_opcode;
aha_ccb_opcode_t ccb_ccb_opcode;
aha_mbox_in_t *in_boxes;
aha_mbox_out_t *out_boxes;
struct scsi_sense_data *sense_buffers;
u_int32_t sense_buffers_physbase;
struct aha_ccb *recovery_accb;
u_int num_boxes;
bus_dma_tag_t parent_dmat; /*
* All dmat's derive from
* the dmat defined by our
* bus.
*/
bus_dma_tag_t buffer_dmat; /* dmat for buffer I/O */
bus_dma_tag_t mailbox_dmat; /* dmat for our mailboxes */
bus_dmamap_t mailbox_dmamap;
bus_dma_tag_t ccb_dmat; /* dmat for our ccb array */
bus_dmamap_t ccb_dmamap;
bus_dma_tag_t sg_dmat; /* dmat for our sg maps */
SLIST_HEAD(, sg_map_node) sg_maps;
bus_addr_t mailbox_physbase;
u_int num_ccbs; /* Number of CCBs malloc'd */
u_int max_ccbs; /* Maximum allocatable CCBs */
u_int max_sg;
u_int unit;
u_int scsi_id;
u_int32_t extended_trans :1,
diff_bus :1,
extended_lun :1,
strict_rr :1,
tag_capable :1,
resource_shortage:1,
:26;
u_int16_t tags_permitted;
u_int16_t disc_permitted;
u_int16_t sync_permitted;
u_int16_t fast_permitted;
u_int8_t init_level;
volatile u_int8_t command_cmp;
volatile u_int8_t latched_status;
u_int32_t bios_addr;
u_int8_t fw_major;
u_int8_t fw_minor;
char model[32];
u_int8_t boardid;
};
extern struct aha_softc *aha_softcs[]; /* XXX Config should handle this */
extern u_long aha_unit;
#define AHA_TEMP_UNIT 0xFF /* Unit for probes */
struct aha_softc* aha_alloc(int unit, bus_space_tag_t tag,
bus_space_handle_t bsh);
void aha_free(struct aha_softc *aha);
int aha_probe(struct aha_softc *aha);
int aha_fetch_adapter_info(struct aha_softc *aha);
int aha_init(struct aha_softc *aha);
int aha_attach(struct aha_softc *aha);
void aha_intr(void *arg);
char * aha_name(struct aha_softc *aha);
int aha_check_probed_iop(u_int ioport);
void aha_mark_probed_bio(isa_compat_io_t port);
void aha_mark_probed_iop(u_int ioport);
void aha_find_probe_range(int ioport,
int *port_index,
int *max_port_index);
int aha_iop_from_bio(isa_compat_io_t bio_index);
#define DEFAULT_CMD_TIMEOUT 10000 /* 1 sec */
int aha_cmd(struct aha_softc *aha, aha_op_t opcode,
u_int8_t *params, u_int param_len,
u_int8_t *reply_data, u_int reply_len,
u_int cmd_timeout);
#define aha_inb(aha, port) \
bus_space_read_1((aha)->tag, (aha)->bsh, port)
#define aha_outb(aha, port, value) \
bus_space_write_1((aha)->tag, (aha)->bsh, port, value)
#ifndef EXTRA_AHA
#if NPNP > 0
#define EXTRA_AHA MAX_PNP_CARDS
#else
#define EXTRA_AHA 0
#endif
#endif
#define NAHATOT (NAHA + EXTRA_AHA)
#define AHA1542_PNP 0x42159004 /* ADP1542 */
#define AHA1542_PNPCOMPAT 0xA000D040 /* PNP00A0 */
#endif /* _AHA_H_ */
Reference in New Issue View Git Blame Copy Permalink