2017-12-19 15:49:03 +00:00
|
|
|
/* SPDX-License-Identifier: BSD-3-Clause
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
* Copyright(c) 2016-2018 Intel Corporation
|
2016-03-09 13:37:25 +00:00
|
|
|
*/
|
|
|
|
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
#include <dirent.h>
|
|
|
|
#include <errno.h>
|
2016-03-09 13:37:25 +00:00
|
|
|
#include <fcntl.h>
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
#include <fnmatch.h>
|
|
|
|
#include <inttypes.h>
|
|
|
|
#include <libgen.h>
|
|
|
|
#include <limits.h>
|
|
|
|
#include <pthread.h>
|
|
|
|
#include <stdio.h>
|
2016-03-09 13:37:25 +00:00
|
|
|
#include <stdlib.h>
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
#include <string.h>
|
2018-03-13 17:42:38 +00:00
|
|
|
#include <sys/file.h>
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
#include <sys/time.h>
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
#include <sys/types.h>
|
|
|
|
#include <sys/socket.h>
|
|
|
|
#include <sys/un.h>
|
|
|
|
#include <unistd.h>
|
|
|
|
|
|
|
|
#include <rte_common.h>
|
|
|
|
#include <rte_cycles.h>
|
2016-03-09 13:37:25 +00:00
|
|
|
#include <rte_eal.h>
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
#include <rte_errno.h>
|
|
|
|
#include <rte_lcore.h>
|
|
|
|
#include <rte_log.h>
|
2016-03-09 13:37:25 +00:00
|
|
|
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
#include "eal_private.h"
|
2016-03-09 13:37:25 +00:00
|
|
|
#include "eal_filesystem.h"
|
|
|
|
#include "eal_internal_cfg.h"
|
|
|
|
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
static int mp_fd = -1;
|
|
|
|
static char mp_filter[PATH_MAX]; /* Filter for secondary process sockets */
|
|
|
|
static char mp_dir_path[PATH_MAX]; /* The directory path for all mp sockets */
|
|
|
|
static pthread_mutex_t mp_mutex_action = PTHREAD_MUTEX_INITIALIZER;
|
|
|
|
|
|
|
|
struct action_entry {
|
|
|
|
TAILQ_ENTRY(action_entry) next;
|
|
|
|
char action_name[RTE_MP_MAX_NAME_LEN];
|
|
|
|
rte_mp_t action;
|
|
|
|
};
|
|
|
|
|
|
|
|
/** Double linked list of actions. */
|
|
|
|
TAILQ_HEAD(action_entry_list, action_entry);
|
|
|
|
|
|
|
|
static struct action_entry_list action_entry_list =
|
|
|
|
TAILQ_HEAD_INITIALIZER(action_entry_list);
|
|
|
|
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
enum mp_type {
|
|
|
|
MP_MSG, /* Share message with peers, will not block */
|
|
|
|
MP_REQ, /* Request for information, Will block for a reply */
|
|
|
|
MP_REP, /* Response to previously-received request */
|
2018-03-13 17:42:40 +00:00
|
|
|
MP_IGN, /* Response telling requester to ignore this response */
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
};
|
|
|
|
|
|
|
|
struct mp_msg_internal {
|
|
|
|
int type;
|
|
|
|
struct rte_mp_msg msg;
|
|
|
|
};
|
|
|
|
|
2018-03-31 18:06:14 +01:00
|
|
|
struct pending_request {
|
|
|
|
TAILQ_ENTRY(pending_request) next;
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
int reply_received;
|
|
|
|
char dst[PATH_MAX];
|
|
|
|
struct rte_mp_msg *request;
|
|
|
|
struct rte_mp_msg *reply;
|
|
|
|
pthread_cond_t cond;
|
|
|
|
};
|
|
|
|
|
2018-03-31 18:06:14 +01:00
|
|
|
TAILQ_HEAD(pending_request_list, pending_request);
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
|
|
|
|
static struct {
|
2018-03-31 18:06:14 +01:00
|
|
|
struct pending_request_list requests;
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
pthread_mutex_t lock;
|
2018-03-31 18:06:14 +01:00
|
|
|
} pending_requests = {
|
|
|
|
.requests = TAILQ_HEAD_INITIALIZER(pending_requests.requests),
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
.lock = PTHREAD_MUTEX_INITIALIZER
|
|
|
|
};
|
|
|
|
|
2018-03-13 17:42:40 +00:00
|
|
|
/* forward declarations */
|
|
|
|
static int
|
|
|
|
mp_send(struct rte_mp_msg *msg, const char *peer, int type);
|
|
|
|
|
|
|
|
|
2018-03-31 18:06:14 +01:00
|
|
|
static struct pending_request *
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
find_sync_request(const char *dst, const char *act_name)
|
|
|
|
{
|
2018-03-31 18:06:14 +01:00
|
|
|
struct pending_request *r;
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
|
2018-03-31 18:06:14 +01:00
|
|
|
TAILQ_FOREACH(r, &pending_requests.requests, next) {
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
if (!strcmp(r->dst, dst) &&
|
|
|
|
!strcmp(r->request->name, act_name))
|
|
|
|
break;
|
|
|
|
}
|
|
|
|
|
|
|
|
return r;
|
|
|
|
}
|
|
|
|
|
2018-03-13 17:42:36 +00:00
|
|
|
static void
|
|
|
|
create_socket_path(const char *name, char *buf, int len)
|
|
|
|
{
|
|
|
|
const char *prefix = eal_mp_socket_path();
|
|
|
|
|
|
|
|
if (strlen(name) > 0)
|
|
|
|
snprintf(buf, len, "%s_%s", prefix, name);
|
|
|
|
else
|
|
|
|
snprintf(buf, len, "%s", prefix);
|
|
|
|
}
|
|
|
|
|
2016-03-09 13:37:25 +00:00
|
|
|
int
|
|
|
|
rte_eal_primary_proc_alive(const char *config_file_path)
|
|
|
|
{
|
|
|
|
int config_fd;
|
|
|
|
|
|
|
|
if (config_file_path)
|
|
|
|
config_fd = open(config_file_path, O_RDONLY);
|
|
|
|
else {
|
2017-06-26 06:49:46 +00:00
|
|
|
const char *path;
|
|
|
|
|
|
|
|
path = eal_runtime_config_path();
|
|
|
|
config_fd = open(path, O_RDONLY);
|
2016-03-09 13:37:25 +00:00
|
|
|
}
|
|
|
|
if (config_fd < 0)
|
|
|
|
return 0;
|
|
|
|
|
|
|
|
int ret = lockf(config_fd, F_TEST, 0);
|
|
|
|
close(config_fd);
|
|
|
|
|
|
|
|
return !!ret;
|
|
|
|
}
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
|
|
|
|
static struct action_entry *
|
|
|
|
find_action_entry_by_name(const char *name)
|
|
|
|
{
|
|
|
|
struct action_entry *entry;
|
|
|
|
|
|
|
|
TAILQ_FOREACH(entry, &action_entry_list, next) {
|
|
|
|
if (strncmp(entry->action_name, name, RTE_MP_MAX_NAME_LEN) == 0)
|
|
|
|
break;
|
|
|
|
}
|
|
|
|
|
|
|
|
return entry;
|
|
|
|
}
|
|
|
|
|
|
|
|
static int
|
|
|
|
validate_action_name(const char *name)
|
|
|
|
{
|
|
|
|
if (name == NULL) {
|
|
|
|
RTE_LOG(ERR, EAL, "Action name cannot be NULL\n");
|
2018-02-10 13:15:15 +00:00
|
|
|
rte_errno = EINVAL;
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
return -1;
|
|
|
|
}
|
|
|
|
if (strnlen(name, RTE_MP_MAX_NAME_LEN) == 0) {
|
|
|
|
RTE_LOG(ERR, EAL, "Length of action name is zero\n");
|
2018-02-10 13:15:15 +00:00
|
|
|
rte_errno = EINVAL;
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
return -1;
|
|
|
|
}
|
|
|
|
if (strnlen(name, RTE_MP_MAX_NAME_LEN) == RTE_MP_MAX_NAME_LEN) {
|
2018-02-10 13:15:15 +00:00
|
|
|
rte_errno = E2BIG;
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
return -1;
|
|
|
|
}
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
int __rte_experimental
|
|
|
|
rte_mp_action_register(const char *name, rte_mp_t action)
|
|
|
|
{
|
|
|
|
struct action_entry *entry;
|
|
|
|
|
|
|
|
if (validate_action_name(name))
|
|
|
|
return -1;
|
|
|
|
|
|
|
|
entry = malloc(sizeof(struct action_entry));
|
|
|
|
if (entry == NULL) {
|
2018-02-10 13:15:15 +00:00
|
|
|
rte_errno = ENOMEM;
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
return -1;
|
|
|
|
}
|
|
|
|
strcpy(entry->action_name, name);
|
|
|
|
entry->action = action;
|
|
|
|
|
|
|
|
pthread_mutex_lock(&mp_mutex_action);
|
|
|
|
if (find_action_entry_by_name(name) != NULL) {
|
|
|
|
pthread_mutex_unlock(&mp_mutex_action);
|
2018-02-10 13:15:15 +00:00
|
|
|
rte_errno = EEXIST;
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
free(entry);
|
|
|
|
return -1;
|
|
|
|
}
|
|
|
|
TAILQ_INSERT_TAIL(&action_entry_list, entry, next);
|
|
|
|
pthread_mutex_unlock(&mp_mutex_action);
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
void __rte_experimental
|
|
|
|
rte_mp_action_unregister(const char *name)
|
|
|
|
{
|
|
|
|
struct action_entry *entry;
|
|
|
|
|
|
|
|
if (validate_action_name(name))
|
|
|
|
return;
|
|
|
|
|
|
|
|
pthread_mutex_lock(&mp_mutex_action);
|
|
|
|
entry = find_action_entry_by_name(name);
|
|
|
|
if (entry == NULL) {
|
|
|
|
pthread_mutex_unlock(&mp_mutex_action);
|
|
|
|
return;
|
|
|
|
}
|
|
|
|
TAILQ_REMOVE(&action_entry_list, entry, next);
|
|
|
|
pthread_mutex_unlock(&mp_mutex_action);
|
|
|
|
free(entry);
|
|
|
|
}
|
|
|
|
|
|
|
|
static int
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
read_msg(struct mp_msg_internal *m, struct sockaddr_un *s)
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
{
|
|
|
|
int msglen;
|
|
|
|
struct iovec iov;
|
|
|
|
struct msghdr msgh;
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
char control[CMSG_SPACE(sizeof(m->msg.fds))];
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
struct cmsghdr *cmsg;
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
int buflen = sizeof(*m) - sizeof(m->msg.fds);
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
|
|
|
|
memset(&msgh, 0, sizeof(msgh));
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
iov.iov_base = m;
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
iov.iov_len = buflen;
|
|
|
|
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
msgh.msg_name = s;
|
|
|
|
msgh.msg_namelen = sizeof(*s);
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
msgh.msg_iov = &iov;
|
|
|
|
msgh.msg_iovlen = 1;
|
|
|
|
msgh.msg_control = control;
|
|
|
|
msgh.msg_controllen = sizeof(control);
|
|
|
|
|
|
|
|
msglen = recvmsg(mp_fd, &msgh, 0);
|
|
|
|
if (msglen < 0) {
|
|
|
|
RTE_LOG(ERR, EAL, "recvmsg failed, %s\n", strerror(errno));
|
|
|
|
return -1;
|
|
|
|
}
|
|
|
|
|
|
|
|
if (msglen != buflen || (msgh.msg_flags & (MSG_TRUNC | MSG_CTRUNC))) {
|
|
|
|
RTE_LOG(ERR, EAL, "truncted msg\n");
|
|
|
|
return -1;
|
|
|
|
}
|
|
|
|
|
|
|
|
/* read auxiliary FDs if any */
|
|
|
|
for (cmsg = CMSG_FIRSTHDR(&msgh); cmsg != NULL;
|
|
|
|
cmsg = CMSG_NXTHDR(&msgh, cmsg)) {
|
|
|
|
if ((cmsg->cmsg_level == SOL_SOCKET) &&
|
|
|
|
(cmsg->cmsg_type == SCM_RIGHTS)) {
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
memcpy(m->msg.fds, CMSG_DATA(cmsg), sizeof(m->msg.fds));
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
break;
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
static void
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
process_msg(struct mp_msg_internal *m, struct sockaddr_un *s)
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
{
|
2018-03-31 18:06:14 +01:00
|
|
|
struct pending_request *sync_req;
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
struct action_entry *entry;
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
struct rte_mp_msg *msg = &m->msg;
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
rte_mp_t action = NULL;
|
|
|
|
|
|
|
|
RTE_LOG(DEBUG, EAL, "msg: %s\n", msg->name);
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
|
2018-03-13 17:42:40 +00:00
|
|
|
if (m->type == MP_REP || m->type == MP_IGN) {
|
2018-03-31 18:06:14 +01:00
|
|
|
pthread_mutex_lock(&pending_requests.lock);
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
sync_req = find_sync_request(s->sun_path, msg->name);
|
|
|
|
if (sync_req) {
|
|
|
|
memcpy(sync_req->reply, msg, sizeof(*msg));
|
2018-03-13 17:42:40 +00:00
|
|
|
/* -1 indicates that we've been asked to ignore */
|
|
|
|
sync_req->reply_received = m->type == MP_REP ? 1 : -1;
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
pthread_cond_signal(&sync_req->cond);
|
|
|
|
} else
|
|
|
|
RTE_LOG(ERR, EAL, "Drop mp reply: %s\n", msg->name);
|
2018-03-31 18:06:14 +01:00
|
|
|
pthread_mutex_unlock(&pending_requests.lock);
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
return;
|
|
|
|
}
|
|
|
|
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
pthread_mutex_lock(&mp_mutex_action);
|
|
|
|
entry = find_action_entry_by_name(msg->name);
|
|
|
|
if (entry != NULL)
|
|
|
|
action = entry->action;
|
|
|
|
pthread_mutex_unlock(&mp_mutex_action);
|
|
|
|
|
2018-03-13 17:42:40 +00:00
|
|
|
if (!action) {
|
|
|
|
if (m->type == MP_REQ && !internal_config.init_complete) {
|
|
|
|
/* if this is a request, and init is not yet complete,
|
|
|
|
* and callback wasn't registered, we should tell the
|
|
|
|
* requester to ignore our existence because we're not
|
|
|
|
* yet ready to process this request.
|
|
|
|
*/
|
|
|
|
struct rte_mp_msg dummy;
|
|
|
|
memset(&dummy, 0, sizeof(dummy));
|
|
|
|
mp_send(&dummy, s->sun_path, MP_IGN);
|
|
|
|
} else {
|
|
|
|
RTE_LOG(ERR, EAL, "Cannot find action: %s\n",
|
|
|
|
msg->name);
|
|
|
|
}
|
|
|
|
} else if (action(msg, s->sun_path) < 0) {
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
RTE_LOG(ERR, EAL, "Fail to handle message: %s\n", msg->name);
|
2018-03-13 17:42:40 +00:00
|
|
|
}
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
static void *
|
|
|
|
mp_handle(void *arg __rte_unused)
|
|
|
|
{
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
struct mp_msg_internal msg;
|
|
|
|
struct sockaddr_un sa;
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
|
|
|
|
while (1) {
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
if (read_msg(&msg, &sa) == 0)
|
|
|
|
process_msg(&msg, &sa);
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
return NULL;
|
|
|
|
}
|
|
|
|
|
|
|
|
static int
|
|
|
|
open_socket_fd(void)
|
|
|
|
{
|
2018-03-13 17:42:36 +00:00
|
|
|
char peer_name[PATH_MAX] = {0};
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
struct sockaddr_un un;
|
2018-03-13 17:42:36 +00:00
|
|
|
|
|
|
|
if (rte_eal_process_type() == RTE_PROC_SECONDARY)
|
|
|
|
snprintf(peer_name, sizeof(peer_name),
|
|
|
|
"%d_%"PRIx64, getpid(), rte_rdtsc());
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
|
|
|
|
mp_fd = socket(AF_UNIX, SOCK_DGRAM, 0);
|
|
|
|
if (mp_fd < 0) {
|
|
|
|
RTE_LOG(ERR, EAL, "failed to create unix socket\n");
|
|
|
|
return -1;
|
|
|
|
}
|
|
|
|
|
|
|
|
memset(&un, 0, sizeof(un));
|
|
|
|
un.sun_family = AF_UNIX;
|
2018-03-13 17:42:36 +00:00
|
|
|
|
|
|
|
create_socket_path(peer_name, un.sun_path, sizeof(un.sun_path));
|
|
|
|
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
unlink(un.sun_path); /* May still exist since last run */
|
2018-03-13 17:42:36 +00:00
|
|
|
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
if (bind(mp_fd, (struct sockaddr *)&un, sizeof(un)) < 0) {
|
|
|
|
RTE_LOG(ERR, EAL, "failed to bind %s: %s\n",
|
|
|
|
un.sun_path, strerror(errno));
|
|
|
|
close(mp_fd);
|
|
|
|
return -1;
|
|
|
|
}
|
|
|
|
|
|
|
|
RTE_LOG(INFO, EAL, "Multi-process socket %s\n", un.sun_path);
|
|
|
|
return mp_fd;
|
|
|
|
}
|
|
|
|
|
|
|
|
static int
|
|
|
|
unlink_sockets(const char *filter)
|
|
|
|
{
|
|
|
|
int dir_fd;
|
|
|
|
DIR *mp_dir;
|
|
|
|
struct dirent *ent;
|
|
|
|
|
|
|
|
mp_dir = opendir(mp_dir_path);
|
|
|
|
if (!mp_dir) {
|
|
|
|
RTE_LOG(ERR, EAL, "Unable to open directory %s\n", mp_dir_path);
|
|
|
|
return -1;
|
|
|
|
}
|
|
|
|
dir_fd = dirfd(mp_dir);
|
|
|
|
|
|
|
|
while ((ent = readdir(mp_dir))) {
|
|
|
|
if (fnmatch(filter, ent->d_name, 0) == 0)
|
|
|
|
unlinkat(dir_fd, ent->d_name, 0);
|
|
|
|
}
|
|
|
|
|
|
|
|
closedir(mp_dir);
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
int
|
|
|
|
rte_mp_channel_init(void)
|
|
|
|
{
|
|
|
|
char thread_name[RTE_MAX_THREAD_NAME_LEN];
|
2018-03-13 17:42:37 +00:00
|
|
|
char path[PATH_MAX];
|
2018-03-13 17:42:38 +00:00
|
|
|
int dir_fd;
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
pthread_t tid;
|
|
|
|
|
2018-03-13 17:42:37 +00:00
|
|
|
/* create filter path */
|
|
|
|
create_socket_path("*", path, sizeof(path));
|
|
|
|
snprintf(mp_filter, sizeof(mp_filter), "%s", basename(path));
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
|
2018-03-13 17:42:37 +00:00
|
|
|
/* path may have been modified, so recreate it */
|
|
|
|
create_socket_path("*", path, sizeof(path));
|
|
|
|
snprintf(mp_dir_path, sizeof(mp_dir_path), "%s", dirname(path));
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
|
2018-03-13 17:42:38 +00:00
|
|
|
/* lock the directory */
|
|
|
|
dir_fd = open(mp_dir_path, O_RDONLY);
|
|
|
|
if (dir_fd < 0) {
|
|
|
|
RTE_LOG(ERR, EAL, "failed to open %s: %s\n",
|
|
|
|
mp_dir_path, strerror(errno));
|
|
|
|
return -1;
|
|
|
|
}
|
|
|
|
|
|
|
|
if (flock(dir_fd, LOCK_EX)) {
|
|
|
|
RTE_LOG(ERR, EAL, "failed to lock %s: %s\n",
|
|
|
|
mp_dir_path, strerror(errno));
|
|
|
|
close(dir_fd);
|
|
|
|
return -1;
|
|
|
|
}
|
|
|
|
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
if (rte_eal_process_type() == RTE_PROC_PRIMARY &&
|
2018-03-13 17:42:37 +00:00
|
|
|
unlink_sockets(mp_filter)) {
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
RTE_LOG(ERR, EAL, "failed to unlink mp sockets\n");
|
2018-03-13 17:42:38 +00:00
|
|
|
close(dir_fd);
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
return -1;
|
|
|
|
}
|
|
|
|
|
2018-03-13 17:42:38 +00:00
|
|
|
if (open_socket_fd() < 0) {
|
|
|
|
close(dir_fd);
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
return -1;
|
2018-03-13 17:42:38 +00:00
|
|
|
}
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
|
|
|
|
if (pthread_create(&tid, NULL, mp_handle, NULL) < 0) {
|
|
|
|
RTE_LOG(ERR, EAL, "failed to create mp thead: %s\n",
|
|
|
|
strerror(errno));
|
|
|
|
close(mp_fd);
|
2018-03-13 17:42:38 +00:00
|
|
|
close(dir_fd);
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
mp_fd = -1;
|
|
|
|
return -1;
|
|
|
|
}
|
|
|
|
|
|
|
|
/* try best to set thread name */
|
|
|
|
snprintf(thread_name, RTE_MAX_THREAD_NAME_LEN, "rte_mp_handle");
|
|
|
|
rte_thread_setname(tid, thread_name);
|
2018-03-13 17:42:38 +00:00
|
|
|
|
|
|
|
/* unlock the directory */
|
|
|
|
flock(dir_fd, LOCK_UN);
|
|
|
|
close(dir_fd);
|
|
|
|
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
/**
|
|
|
|
* Return -1, as fail to send message and it's caused by the local side.
|
|
|
|
* Return 0, as fail to send message and it's caused by the remote side.
|
|
|
|
* Return 1, as succeed to send message.
|
|
|
|
*
|
|
|
|
*/
|
|
|
|
static int
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
send_msg(const char *dst_path, struct rte_mp_msg *msg, int type)
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
{
|
|
|
|
int snd;
|
|
|
|
struct iovec iov;
|
|
|
|
struct msghdr msgh;
|
|
|
|
struct cmsghdr *cmsg;
|
|
|
|
struct sockaddr_un dst;
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
struct mp_msg_internal m;
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
int fd_size = msg->num_fds * sizeof(int);
|
|
|
|
char control[CMSG_SPACE(fd_size)];
|
|
|
|
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
m.type = type;
|
|
|
|
memcpy(&m.msg, msg, sizeof(*msg));
|
|
|
|
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
memset(&dst, 0, sizeof(dst));
|
|
|
|
dst.sun_family = AF_UNIX;
|
|
|
|
snprintf(dst.sun_path, sizeof(dst.sun_path), "%s", dst_path);
|
|
|
|
|
|
|
|
memset(&msgh, 0, sizeof(msgh));
|
|
|
|
memset(control, 0, sizeof(control));
|
|
|
|
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
iov.iov_base = &m;
|
|
|
|
iov.iov_len = sizeof(m) - sizeof(msg->fds);
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
|
|
|
|
msgh.msg_name = &dst;
|
|
|
|
msgh.msg_namelen = sizeof(dst);
|
|
|
|
msgh.msg_iov = &iov;
|
|
|
|
msgh.msg_iovlen = 1;
|
|
|
|
msgh.msg_control = control;
|
|
|
|
msgh.msg_controllen = sizeof(control);
|
|
|
|
|
|
|
|
cmsg = CMSG_FIRSTHDR(&msgh);
|
|
|
|
cmsg->cmsg_len = CMSG_LEN(fd_size);
|
|
|
|
cmsg->cmsg_level = SOL_SOCKET;
|
|
|
|
cmsg->cmsg_type = SCM_RIGHTS;
|
|
|
|
memcpy(CMSG_DATA(cmsg), msg->fds, fd_size);
|
|
|
|
|
|
|
|
do {
|
|
|
|
snd = sendmsg(mp_fd, &msgh, 0);
|
|
|
|
} while (snd < 0 && errno == EINTR);
|
|
|
|
|
|
|
|
if (snd < 0) {
|
|
|
|
rte_errno = errno;
|
|
|
|
/* Check if it caused by peer process exits */
|
2018-03-13 17:42:36 +00:00
|
|
|
if (errno == ECONNREFUSED &&
|
|
|
|
rte_eal_process_type() == RTE_PROC_PRIMARY) {
|
|
|
|
unlink(dst_path);
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
return 0;
|
|
|
|
}
|
2018-03-02 08:41:36 +00:00
|
|
|
if (errno == ENOBUFS) {
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
RTE_LOG(ERR, EAL, "Peer cannot receive message %s\n",
|
|
|
|
dst_path);
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
RTE_LOG(ERR, EAL, "failed to send to (%s) due to %s\n",
|
|
|
|
dst_path, strerror(errno));
|
|
|
|
return -1;
|
|
|
|
}
|
|
|
|
|
|
|
|
return 1;
|
|
|
|
}
|
|
|
|
|
|
|
|
static int
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
mp_send(struct rte_mp_msg *msg, const char *peer, int type)
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
{
|
2018-03-13 17:42:38 +00:00
|
|
|
int dir_fd, ret = 0;
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
DIR *mp_dir;
|
|
|
|
struct dirent *ent;
|
|
|
|
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
if (!peer && (rte_eal_process_type() == RTE_PROC_SECONDARY))
|
|
|
|
peer = eal_mp_socket_path();
|
|
|
|
|
|
|
|
if (peer) {
|
|
|
|
if (send_msg(peer, msg, type) < 0)
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
return -1;
|
|
|
|
else
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
/* broadcast to all secondary processes */
|
|
|
|
mp_dir = opendir(mp_dir_path);
|
|
|
|
if (!mp_dir) {
|
|
|
|
RTE_LOG(ERR, EAL, "Unable to open directory %s\n",
|
|
|
|
mp_dir_path);
|
|
|
|
rte_errno = errno;
|
|
|
|
return -1;
|
|
|
|
}
|
2018-03-13 17:42:38 +00:00
|
|
|
|
|
|
|
dir_fd = dirfd(mp_dir);
|
|
|
|
/* lock the directory to prevent processes spinning up while we send */
|
|
|
|
if (flock(dir_fd, LOCK_EX)) {
|
|
|
|
RTE_LOG(ERR, EAL, "Unable to lock directory %s\n",
|
|
|
|
mp_dir_path);
|
|
|
|
rte_errno = errno;
|
|
|
|
closedir(mp_dir);
|
|
|
|
return -1;
|
|
|
|
}
|
|
|
|
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
while ((ent = readdir(mp_dir))) {
|
2018-03-02 08:41:34 +00:00
|
|
|
char path[PATH_MAX];
|
|
|
|
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
if (fnmatch(mp_filter, ent->d_name, 0) != 0)
|
|
|
|
continue;
|
|
|
|
|
2018-03-02 08:41:34 +00:00
|
|
|
snprintf(path, sizeof(path), "%s/%s", mp_dir_path,
|
|
|
|
ent->d_name);
|
|
|
|
if (send_msg(path, msg, type) < 0)
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
ret = -1;
|
|
|
|
}
|
2018-03-13 17:42:38 +00:00
|
|
|
/* unlock the dir */
|
|
|
|
flock(dir_fd, LOCK_UN);
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
|
2018-03-13 17:42:38 +00:00
|
|
|
/* dir_fd automatically closed on closedir */
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
closedir(mp_dir);
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
return ret;
|
|
|
|
}
|
|
|
|
|
|
|
|
static bool
|
|
|
|
check_input(const struct rte_mp_msg *msg)
|
|
|
|
{
|
|
|
|
if (msg == NULL) {
|
|
|
|
RTE_LOG(ERR, EAL, "Msg cannot be NULL\n");
|
2018-02-10 13:15:15 +00:00
|
|
|
rte_errno = EINVAL;
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
return false;
|
|
|
|
}
|
|
|
|
|
|
|
|
if (validate_action_name(msg->name))
|
|
|
|
return false;
|
|
|
|
|
|
|
|
if (msg->len_param > RTE_MP_MAX_PARAM_LEN) {
|
|
|
|
RTE_LOG(ERR, EAL, "Message data is too long\n");
|
2018-02-10 13:15:15 +00:00
|
|
|
rte_errno = E2BIG;
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
return false;
|
|
|
|
}
|
|
|
|
|
|
|
|
if (msg->num_fds > RTE_MP_MAX_FD_NUM) {
|
|
|
|
RTE_LOG(ERR, EAL, "Cannot send more than %d FDs\n",
|
|
|
|
RTE_MP_MAX_FD_NUM);
|
2018-02-10 13:15:15 +00:00
|
|
|
rte_errno = E2BIG;
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
return false;
|
|
|
|
}
|
|
|
|
|
|
|
|
return true;
|
|
|
|
}
|
|
|
|
|
|
|
|
int __rte_experimental
|
|
|
|
rte_mp_sendmsg(struct rte_mp_msg *msg)
|
|
|
|
{
|
|
|
|
if (!check_input(msg))
|
|
|
|
return -1;
|
|
|
|
|
|
|
|
RTE_LOG(DEBUG, EAL, "sendmsg: %s\n", msg->name);
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
return mp_send(msg, NULL, MP_MSG);
|
|
|
|
}
|
|
|
|
|
|
|
|
static int
|
|
|
|
mp_request_one(const char *dst, struct rte_mp_msg *req,
|
|
|
|
struct rte_mp_reply *reply, const struct timespec *ts)
|
|
|
|
{
|
|
|
|
int ret;
|
|
|
|
struct rte_mp_msg msg, *tmp;
|
2018-03-31 18:06:14 +01:00
|
|
|
struct pending_request sync_req, *exist;
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
|
|
|
|
sync_req.reply_received = 0;
|
|
|
|
strcpy(sync_req.dst, dst);
|
|
|
|
sync_req.request = req;
|
|
|
|
sync_req.reply = &msg;
|
|
|
|
pthread_cond_init(&sync_req.cond, NULL);
|
|
|
|
|
2018-03-31 18:06:14 +01:00
|
|
|
pthread_mutex_lock(&pending_requests.lock);
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
exist = find_sync_request(dst, req->name);
|
|
|
|
if (!exist)
|
2018-03-31 18:06:14 +01:00
|
|
|
TAILQ_INSERT_TAIL(&pending_requests.requests, &sync_req, next);
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
if (exist) {
|
|
|
|
RTE_LOG(ERR, EAL, "A pending request %s:%s\n", dst, req->name);
|
2018-02-10 13:15:15 +00:00
|
|
|
rte_errno = EEXIST;
|
2018-03-31 18:06:14 +01:00
|
|
|
pthread_mutex_unlock(&pending_requests.lock);
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
return -1;
|
|
|
|
}
|
|
|
|
|
|
|
|
ret = send_msg(dst, req, MP_REQ);
|
|
|
|
if (ret < 0) {
|
|
|
|
RTE_LOG(ERR, EAL, "Fail to send request %s:%s\n",
|
|
|
|
dst, req->name);
|
|
|
|
return -1;
|
|
|
|
} else if (ret == 0)
|
|
|
|
return 0;
|
|
|
|
|
|
|
|
reply->nb_sent++;
|
|
|
|
|
|
|
|
do {
|
2018-03-13 17:42:39 +00:00
|
|
|
ret = pthread_cond_timedwait(&sync_req.cond,
|
2018-03-31 18:06:14 +01:00
|
|
|
&pending_requests.lock, ts);
|
2018-03-13 17:42:39 +00:00
|
|
|
} while (ret != 0 && ret != ETIMEDOUT);
|
|
|
|
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
/* We got the lock now */
|
2018-03-31 18:06:14 +01:00
|
|
|
TAILQ_REMOVE(&pending_requests.requests, &sync_req, next);
|
|
|
|
pthread_mutex_unlock(&pending_requests.lock);
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
|
|
|
|
if (sync_req.reply_received == 0) {
|
|
|
|
RTE_LOG(ERR, EAL, "Fail to recv reply for request %s:%s\n",
|
|
|
|
dst, req->name);
|
2018-02-10 13:15:15 +00:00
|
|
|
rte_errno = ETIMEDOUT;
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
return -1;
|
|
|
|
}
|
2018-03-13 17:42:40 +00:00
|
|
|
if (sync_req.reply_received == -1) {
|
|
|
|
RTE_LOG(DEBUG, EAL, "Asked to ignore response\n");
|
|
|
|
/* not receiving this message is not an error, so decrement
|
|
|
|
* number of sent messages
|
|
|
|
*/
|
|
|
|
reply->nb_sent--;
|
|
|
|
return 0;
|
|
|
|
}
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
|
|
|
|
tmp = realloc(reply->msgs, sizeof(msg) * (reply->nb_received + 1));
|
|
|
|
if (!tmp) {
|
|
|
|
RTE_LOG(ERR, EAL, "Fail to alloc reply for request %s:%s\n",
|
|
|
|
dst, req->name);
|
2018-02-10 13:15:15 +00:00
|
|
|
rte_errno = ENOMEM;
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
return -1;
|
|
|
|
}
|
|
|
|
memcpy(&tmp[reply->nb_received], &msg, sizeof(msg));
|
|
|
|
reply->msgs = tmp;
|
|
|
|
reply->nb_received++;
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
int __rte_experimental
|
|
|
|
rte_mp_request(struct rte_mp_msg *req, struct rte_mp_reply *reply,
|
|
|
|
const struct timespec *ts)
|
|
|
|
{
|
2018-03-13 17:42:38 +00:00
|
|
|
int dir_fd, ret = 0;
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
DIR *mp_dir;
|
|
|
|
struct dirent *ent;
|
|
|
|
struct timeval now;
|
|
|
|
struct timespec end;
|
|
|
|
|
|
|
|
RTE_LOG(DEBUG, EAL, "request: %s\n", req->name);
|
|
|
|
|
|
|
|
if (check_input(req) == false)
|
|
|
|
return -1;
|
|
|
|
if (gettimeofday(&now, NULL) < 0) {
|
|
|
|
RTE_LOG(ERR, EAL, "Faile to get current time\n");
|
|
|
|
rte_errno = errno;
|
|
|
|
return -1;
|
|
|
|
}
|
|
|
|
|
|
|
|
end.tv_nsec = (now.tv_usec * 1000 + ts->tv_nsec) % 1000000000;
|
|
|
|
end.tv_sec = now.tv_sec + ts->tv_sec +
|
|
|
|
(now.tv_usec * 1000 + ts->tv_nsec) / 1000000000;
|
|
|
|
|
|
|
|
reply->nb_sent = 0;
|
|
|
|
reply->nb_received = 0;
|
|
|
|
reply->msgs = NULL;
|
|
|
|
|
|
|
|
/* for secondary process, send request to the primary process only */
|
|
|
|
if (rte_eal_process_type() == RTE_PROC_SECONDARY)
|
|
|
|
return mp_request_one(eal_mp_socket_path(), req, reply, &end);
|
|
|
|
|
|
|
|
/* for primary process, broadcast request, and collect reply 1 by 1 */
|
|
|
|
mp_dir = opendir(mp_dir_path);
|
|
|
|
if (!mp_dir) {
|
|
|
|
RTE_LOG(ERR, EAL, "Unable to open directory %s\n", mp_dir_path);
|
|
|
|
rte_errno = errno;
|
|
|
|
return -1;
|
|
|
|
}
|
|
|
|
|
2018-03-13 17:42:38 +00:00
|
|
|
dir_fd = dirfd(mp_dir);
|
|
|
|
/* lock the directory to prevent processes spinning up while we send */
|
|
|
|
if (flock(dir_fd, LOCK_EX)) {
|
|
|
|
RTE_LOG(ERR, EAL, "Unable to lock directory %s\n",
|
|
|
|
mp_dir_path);
|
|
|
|
closedir(mp_dir);
|
|
|
|
rte_errno = errno;
|
|
|
|
return -1;
|
|
|
|
}
|
|
|
|
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
while ((ent = readdir(mp_dir))) {
|
2018-03-02 08:41:35 +00:00
|
|
|
char path[PATH_MAX];
|
|
|
|
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
if (fnmatch(mp_filter, ent->d_name, 0) != 0)
|
|
|
|
continue;
|
|
|
|
|
2018-03-02 08:41:35 +00:00
|
|
|
snprintf(path, sizeof(path), "%s/%s", mp_dir_path,
|
|
|
|
ent->d_name);
|
|
|
|
|
|
|
|
if (mp_request_one(path, req, reply, &end))
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
ret = -1;
|
|
|
|
}
|
2018-03-13 17:42:38 +00:00
|
|
|
/* unlock the directory */
|
|
|
|
flock(dir_fd, LOCK_UN);
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
|
2018-03-13 17:42:38 +00:00
|
|
|
/* dir_fd automatically closed on closedir */
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
closedir(mp_dir);
|
|
|
|
return ret;
|
|
|
|
}
|
|
|
|
|
|
|
|
int __rte_experimental
|
|
|
|
rte_mp_reply(struct rte_mp_msg *msg, const char *peer)
|
|
|
|
{
|
|
|
|
|
|
|
|
RTE_LOG(DEBUG, EAL, "reply: %s\n", msg->name);
|
|
|
|
|
|
|
|
if (check_input(msg) == false)
|
|
|
|
return -1;
|
|
|
|
|
|
|
|
if (peer == NULL) {
|
|
|
|
RTE_LOG(ERR, EAL, "peer is not specified\n");
|
2018-02-10 13:15:15 +00:00
|
|
|
rte_errno = EINVAL;
|
eal: add synchronous multi-process communication
We need the synchronous way for multi-process communication,
i.e., blockingly waiting for reply message when we send a request
to the peer process.
We add two APIs rte_eal_mp_request() and rte_eal_mp_reply() for
such use case. By invoking rte_eal_mp_request(), a request message
is sent out, and then it waits there for a reply message. The caller
can specify the timeout. And the response messages will be collected
and returned so that the caller can decide how to translate them.
The API rte_eal_mp_reply() is always called by an mp action handler.
Here we add another parameter for rte_eal_mp_t so that the action
handler knows which peer address to reply.
sender-process receiver-process
---------------------- ----------------
thread-n
|_rte_eal_mp_request() ----------> mp-thread
|_timedwait() |_process_msg()
|_action()
|_rte_eal_mp_reply()
mp_thread <---------------------|
|_process_msg()
|_signal(send_thread)
thread-m <----------|
|_collect-reply
* A secondary process is only allowed to talk to the primary process.
* If there are multiple secondary processes for the primary process,
it will send request to peer1, collect response from peer1; then
send request to peer2, collect response from peer2, and so on.
* When thread-n is sending request, thread-m of that process can send
request at the same time.
* For pair <action_name, peer>, we guarantee that only one such request
is on the fly.
Suggested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:09 +00:00
|
|
|
return -1;
|
|
|
|
}
|
|
|
|
|
|
|
|
return mp_send(msg, peer, MP_REP);
|
eal: add channel for multi-process communication
Previouly, there are three channels for multi-process
(i.e., primary/secondary) communication.
1. Config-file based channel, in which, the primary process writes
info into a pre-defined config file, and the secondary process
reads the info out.
2. vfio submodule has its own channel based on unix socket for the
secondary process to get container fd and group fd from the
primary process.
3. pdump submodule also has its own channel based on unix socket for
packet dump.
It'd be good to have a generic communication channel for multi-process
communication to accommodate the requirements including:
a. Secondary wants to send info to primary, for example, secondary
would like to send request (about some specific vdev to primary).
b. Sending info at any time, instead of just initialization time.
c. Share FDs with the other side, for vdev like vhost, related FDs
(memory region, kick) should be shared.
d. A send message request needs the other side to response immediately.
This patch proposes to create a communication channel, based on datagram
unix socket, for above requirements. Each process will block on a unix
socket waiting for messages from the peers.
Three new APIs are added:
1. rte_eal_mp_action_register() is used to register an action,
indexed by a string, when a component at receiver side would like
to response the messages from the peer processe.
2. rte_eal_mp_action_unregister() is used to unregister the action
if the calling component does not want to response the messages.
3. rte_eal_mp_sendmsg() is used to send a message, and returns
immediately. If there are n secondary processes, the primary
process will send n messages.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
2018-01-30 06:58:08 +00:00
|
|
|
}
|