net/ena: adjust new line in log messages

Only PMD_*_LOG is adding new line character to the log message.
All printouts were adjusted for consistency.

Signed-off-by: Rafal Kozik <rk@semihalf.com>
Acked-by: Michal Krawczyk <mk@semihalf.com>
This commit is contained in:
Rafal Kozik 2018-12-14 14:18:37 +01:00 committed by Ferruh Yigit
parent e457bc70e5
commit 498c687aee

View File

@ -553,7 +553,7 @@ ena_dev_reset(struct rte_eth_dev *dev)
ena_destroy_device(dev);
rc = eth_ena_dev_init(dev);
if (rc)
PMD_INIT_LOG(CRIT, "Cannot initialize device\n");
PMD_INIT_LOG(CRIT, "Cannot initialize device");
return rc;
}
@ -880,7 +880,7 @@ static int ena_check_valid_conf(struct ena_adapter *adapter)
if (max_frame_len > adapter->max_mtu || max_frame_len < ENA_MIN_MTU) {
PMD_INIT_LOG(ERR, "Unsupported MTU of %d. "
"max mtu: %d, min mtu: %d\n",
"max mtu: %d, min mtu: %d",
max_frame_len, adapter->max_mtu, ENA_MIN_MTU);
return ENA_COM_UNSUPPORTED;
}
@ -984,7 +984,7 @@ static int ena_stats_get(struct rte_eth_dev *dev,
memset(&ena_stats, 0, sizeof(ena_stats));
rc = ena_com_get_dev_basic_stats(ena_dev, &ena_stats);
if (unlikely(rc)) {
RTE_LOG(ERR, PMD, "Could not retrieve statistics from ENA");
RTE_LOG(ERR, PMD, "Could not retrieve statistics from ENA\n");
return rc;
}
@ -1013,12 +1013,12 @@ static int ena_mtu_set(struct rte_eth_dev *dev, uint16_t mtu)
struct ena_com_dev *ena_dev;
int rc = 0;
ena_assert_msg(dev->data != NULL, "Uninitialized device");
ena_assert_msg(dev->data->dev_private != NULL, "Uninitialized device");
ena_assert_msg(dev->data != NULL, "Uninitialized device\n");
ena_assert_msg(dev->data->dev_private != NULL, "Uninitialized device\n");
adapter = (struct ena_adapter *)(dev->data->dev_private);
ena_dev = &adapter->ena_dev;
ena_assert_msg(ena_dev != NULL, "Uninitialized device");
ena_assert_msg(ena_dev != NULL, "Uninitialized device\n");
if (mtu > ena_get_mtu_conf(adapter) || mtu < ENA_MIN_MTU) {
RTE_LOG(ERR, PMD,
@ -1204,7 +1204,7 @@ static int ena_queue_start(struct ena_ring *ring)
rc = ena_create_io_queue(ring);
if (rc) {
PMD_INIT_LOG(ERR, "Failed to create IO queue!\n");
PMD_INIT_LOG(ERR, "Failed to create IO queue!");
return rc;
}
@ -1248,7 +1248,7 @@ static int ena_tx_queue_setup(struct rte_eth_dev *dev,
if (!rte_is_power_of_2(nb_desc)) {
RTE_LOG(ERR, PMD,
"Unsupported size of TX queue: %d is not a power of 2.",
"Unsupported size of TX queue: %d is not a power of 2.\n",
nb_desc);
return -EINVAL;
}
@ -1337,7 +1337,7 @@ static int ena_rx_queue_setup(struct rte_eth_dev *dev,
if (!rte_is_power_of_2(nb_desc)) {
RTE_LOG(ERR, PMD,
"Unsupported size of RX queue: %d is not a power of 2.",
"Unsupported size of RX queue: %d is not a power of 2.\n",
nb_desc);
return -EINVAL;
}
@ -1410,7 +1410,7 @@ static int ena_populate_rx_queue(struct ena_ring *rxq, unsigned int count)
return 0;
in_use = rxq->next_to_use - rxq->next_to_clean;
ena_assert_msg(((in_use + count) < ring_size), "bad ring state");
ena_assert_msg(((in_use + count) < ring_size), "bad ring state\n");
/* get resources for incoming packets */
rc = rte_mempool_get_bulk(rxq->mb_pool, (void **)mbufs, count);
@ -1643,7 +1643,7 @@ ena_set_queues_placement_policy(struct ena_adapter *adapter,
rc = ena_com_config_dev_mode(ena_dev, llq, llq_default_configurations);
if (unlikely(rc)) {
PMD_INIT_LOG(WARNING, "Failed to config dev mode. "
"Fallback to host mode policy.\n");
"Fallback to host mode policy.");
ena_dev->tx_mem_queue_type = ENA_ADMIN_PLACEMENT_POLICY_HOST;
return 0;
}
@ -1945,12 +1945,12 @@ static void ena_infos_get(struct rte_eth_dev *dev,
uint64_t rx_feat = 0, tx_feat = 0;
int rc = 0;
ena_assert_msg(dev->data != NULL, "Uninitialized device");
ena_assert_msg(dev->data->dev_private != NULL, "Uninitialized device");
ena_assert_msg(dev->data != NULL, "Uninitialized device\n");
ena_assert_msg(dev->data->dev_private != NULL, "Uninitialized device\n");
adapter = (struct ena_adapter *)(dev->data->dev_private);
ena_dev = &adapter->ena_dev;
ena_assert_msg(ena_dev != NULL, "Uninitialized device");
ena_assert_msg(ena_dev != NULL, "Uninitialized device\n");
dev_info->speed_capa =
ETH_LINK_SPEED_1G |