cxgbe: enable jumbo frames

Increase max_rx_pktlen to accommodate jumbo frame size. Perform sanity
checks and enable jumbo mode in rx queue setup. Set link mtu based on
max_rx_pktlen.

Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>

doc/guides/nics/cxgbe.rst

@@ -50,6 +50,7 @@ CXGBE PMD has support for:
 - Promiscuous mode
 - All multicast mode
 - Port hardware statistics
+- Jumbo frames
 
 Limitations
 -----------
@@ -562,3 +563,27 @@ To disable again, run:
 
    testpmd> set flow_ctrl rx off tx off 0 0 0 0 mac_ctrl_frame_fwd off autoneg off 0
    testpmd> set flow_ctrl rx off tx off 0 0 0 0 mac_ctrl_frame_fwd off autoneg off 1
+
+Jumbo Mode
+~~~~~~~~~~
+
+There are two ways to enable sending and receiving of jumbo frames via testpmd.
+One method involves using the **mtu** command, which changes the mtu of an
+individual port without having to stop the selected port. Another method
+involves stopping all the ports first and then running **max-pkt-len** command
+to configure the mtu of all the ports with a single command.
+
+- To configure each port individually, run the mtu command as follows:
+
+  .. code-block:: console
+
+     testpmd> port config mtu 0 9000
+     testpmd> port config mtu 1 9000
+
+- To configure all the ports at once, stop all the ports first and run the
+  max-pkt-len command as follows:
+
+  .. code-block:: console
+
+     testpmd> port stop all
+     testpmd> port config all max-pkt-len 9000

doc/guides/rel_notes/release_2_2.rst

@@ -6,6 +6,7 @@ New Features
 
 * **Enhanced support for the Chelsio CXGBE driver.**
 
+  *  Added support for Jumbo Frames.
   *  Optimize forwarding performance for Chelsio T5 40GbE cards.
 
 

drivers/net/cxgbe/cxgbe.h

@@ -43,6 +43,9 @@
 #define CXGBE_DEFAULT_TX_DESC_SIZE    1024 /* Default TX ring size */
 #define CXGBE_DEFAULT_RX_DESC_SIZE    1024 /* Default RX ring size */
 
+#define CXGBE_MIN_RX_BUFSIZE ETHER_MIN_MTU /* min buf size */
+#define CXGBE_MAX_RX_PKTLEN (9000 + ETHER_HDR_LEN + ETHER_CRC_LEN) /* max pkt */
+
 int cxgbe_probe(struct adapter *adapter);
 int cxgbe_up(struct adapter *adap);
 int cxgbe_down(struct port_info *pi);

drivers/net/cxgbe/cxgbe_ethdev.c

@@ -141,8 +141,8 @@ static void cxgbe_dev_info_get(struct rte_eth_dev *eth_dev,
 	struct adapter *adapter = pi->adapter;
 	int max_queues = adapter->sge.max_ethqsets / adapter->params.nports;
 
-	device_info->min_rx_bufsize = 68; /* XXX: Smallest pkt size */
-	device_info->max_rx_pktlen = 1500; /* XXX: For now we support mtu */
+	device_info->min_rx_bufsize = CXGBE_MIN_RX_BUFSIZE;
+	device_info->max_rx_pktlen = CXGBE_MAX_RX_PKTLEN;
 	device_info->max_rx_queues = max_queues;
 	device_info->max_tx_queues = max_queues;
 	device_info->max_mac_addrs = 1;
@@ -498,6 +498,8 @@ static int cxgbe_dev_rx_queue_setup(struct rte_eth_dev *eth_dev,
 	int err = 0;
 	int msi_idx = 0;
 	unsigned int temp_nb_desc;
+	struct rte_eth_dev_info dev_info;
+	unsigned int pkt_len = eth_dev->data->dev_conf.rxmode.max_rx_pkt_len;
 
 	RTE_SET_USED(rx_conf);
 
@@ -505,6 +507,17 @@ static int cxgbe_dev_rx_queue_setup(struct rte_eth_dev *eth_dev,
 		  __func__, eth_dev->data->nb_rx_queues, queue_idx, nb_desc,
 		  socket_id, mp);
 
+	cxgbe_dev_info_get(eth_dev, &dev_info);
+
+	/* Must accommodate at least ETHER_MIN_MTU */
+	if ((pkt_len < dev_info.min_rx_bufsize) ||
+	    (pkt_len > dev_info.max_rx_pktlen)) {
+		dev_err(adap, "%s: max pkt len must be > %d and <= %d\n",
+			__func__, dev_info.min_rx_bufsize,
+			dev_info.max_rx_pktlen);
+		return -EINVAL;
+	}
+
 	/*  Free up the existing queue  */
 	if (eth_dev->data->rx_queues[queue_idx]) {
 		cxgbe_dev_rx_queue_release(eth_dev->data->rx_queues[queue_idx]);
@@ -534,6 +547,12 @@ static int cxgbe_dev_rx_queue_setup(struct rte_eth_dev *eth_dev,
 	if ((&rxq->fl) != NULL)
 		rxq->fl.size = temp_nb_desc;
 
+	/* Set to jumbo mode if necessary */
+	if (pkt_len > ETHER_MAX_LEN)
+		eth_dev->data->dev_conf.rxmode.jumbo_frame = 1;
+	else
+		eth_dev->data->dev_conf.rxmode.jumbo_frame = 0;
+
 	err = t4_sge_alloc_rxq(adapter, &rxq->rspq, false, eth_dev, msi_idx,
 			       &rxq->fl, t4_ethrx_handler,
 			       t4_get_mps_bg_map(adapter, pi->tx_chan), mp,

drivers/net/cxgbe/cxgbe_main.c

@@ -855,12 +855,13 @@ int link_start(struct port_info *pi)
 {
 	struct adapter *adapter = pi->adapter;
 	int ret;
+	unsigned int mtu = pi->eth_dev->data->dev_conf.rxmode.max_rx_pkt_len;
 
 	/*
 	 * We do not set address filters and promiscuity here, the stack does
 	 * that step explicitly.
 	 */
-	ret = t4_set_rxmode(adapter, adapter->mbox, pi->viid, 1500, -1, -1,
+	ret = t4_set_rxmode(adapter, adapter->mbox, pi->viid, mtu, -1, -1,
 			    -1, 1, true);
 	if (ret == 0) {
 		ret = t4_change_mac(adapter, adapter->mbox, pi->viid,