Add 'RTE_ETH' namespace to all enums & macros in a backward compatible
way. The macros for backward compatibility can be removed in next LTS.
Also updated some struct names to have 'rte_eth' prefix.
All internal components switched to using new names.
Syntax fixed on lines that this patch touches.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Tyler Retzlaff <roretzla@linux.microsoft.com>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Acked-by: Wisam Jaddo <wisamm@nvidia.com>
Acked-by: Rosen Xu <rosen.xu@intel.com>
Acked-by: Chenbo Xia <chenbo.xia@intel.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Acked-by: Somnath Kotur <somnath.kotur@broadcom.com>
Removing 'DEV_RX_OFFLOAD_JUMBO_FRAME' offload flag.
Instead of drivers announce this capability, application can deduct the
capability by checking reported 'dev_info.max_mtu' or
'dev_info.max_rx_pktlen'.
And instead of application setting this flag explicitly to enable jumbo
frames, this can be deduced by driver by comparing requested 'mtu' to
'RTE_ETHER_MTU'.
Removing this additional configuration for simplification.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Reviewed-by: Rosen Xu <rosen.xu@intel.com>
Acked-by: Somnath Kotur <somnath.kotur@broadcom.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Huisong Li <lihuisong@huawei.com>
Acked-by: Hyong Youb Kim <hyonkim@cisco.com>
Acked-by: Michal Krawczyk <mk@semihalf.com>
Move requested MTU value check to the API to prevent the duplicated
code.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Reviewed-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Reviewed-by: Rosen Xu <rosen.xu@intel.com>
Acked-by: Somnath Kotur <somnath.kotur@broadcom.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Setting MTU bigger than RTE_ETHER_MTU requires the jumbo frame support,
and application should enable the jumbo frame offload support for it.
When jumbo frame offload is not enabled by application, but MTU bigger
than RTE_ETHER_MTU is requested there are two options, either fail or
enable jumbo frame offload implicitly.
Enabling jumbo frame offload implicitly is selected by many drivers
since setting a big MTU value already implies it, and this increases
usability.
This patch moves this logic from drivers to the library, both to reduce
the duplicated code in the drivers and to make behaviour more visible.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Reviewed-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Reviewed-by: Rosen Xu <rosen.xu@intel.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Somnath Kotur <somnath.kotur@broadcom.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Huisong Li <lihuisong@huawei.com>
There is a confusion on setting max Rx packet length, this patch aims to
clarify it.
'rte_eth_dev_configure()' API accepts max Rx packet size via
'uint32_t max_rx_pkt_len' field of the config struct 'struct
rte_eth_conf'.
Also 'rte_eth_dev_set_mtu()' API can be used to set the MTU, and result
stored into '(struct rte_eth_dev)->data->mtu'.
These two APIs are related but they work in a disconnected way, they
store the set values in different variables which makes hard to figure
out which one to use, also having two different method for a related
functionality is confusing for the users.
Other issues causing confusion is:
* maximum transmission unit (MTU) is payload of the Ethernet frame. And
'max_rx_pkt_len' is the size of the Ethernet frame. Difference is
Ethernet frame overhead, and this overhead may be different from
device to device based on what device supports, like VLAN and QinQ.
* 'max_rx_pkt_len' is only valid when application requested jumbo frame,
which adds additional confusion and some APIs and PMDs already
discards this documented behavior.
* For the jumbo frame enabled case, 'max_rx_pkt_len' is an mandatory
field, this adds configuration complexity for application.
As solution, both APIs gets MTU as parameter, and both saves the result
in same variable '(struct rte_eth_dev)->data->mtu'. For this
'max_rx_pkt_len' updated as 'mtu', and it is always valid independent
from jumbo frame.
For 'rte_eth_dev_configure()', 'dev->data->dev_conf.rxmode.mtu' is user
request and it should be used only within configure function and result
should be stored to '(struct rte_eth_dev)->data->mtu'. After that point
both application and PMD uses MTU from this variable.
When application doesn't provide an MTU during 'rte_eth_dev_configure()'
default 'RTE_ETHER_MTU' value is used.
Additional clarification done on scattered Rx configuration, in
relation to MTU and Rx buffer size.
MTU is used to configure the device for physical Rx/Tx size limitation,
Rx buffer is where to store Rx packets, many PMDs use mbuf data buffer
size as Rx buffer size.
PMDs compare MTU against Rx buffer size to decide enabling scattered Rx
or not. If scattered Rx is not supported by device, MTU bigger than Rx
buffer size should fail.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Somnath Kotur <somnath.kotur@broadcom.com>
Acked-by: Huisong Li <lihuisong@huawei.com>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Rosen Xu <rosen.xu@intel.com>
Acked-by: Hyong Youb Kim <hyonkim@cisco.com>
Some drivers do not provide per-queue statistics. So, there is no point
to have these misleading zeros in xstats.
Fixes: f30e69b41f ("ethdev: add device flag to bypass auto-filled queue xstats")
Cc: stable@dpdk.org
Signed-off-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Currently, most ethdev callback API use queue ID as parameter, but Rx
and Tx queue release callback use queue object which is used by Rx and
Tx burst data plane callback.
To align with other eth device queue configuration callbacks:
- queue release callbacks are changed to use queue ID
- all drivers are adapted
Signed-off-by: Xueming Li <xuemingl@nvidia.com>
Reviewed-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Somnath Kotur <somnath.kotur@broadcom.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
Let's try to enforce the convention where most drivers use a pmd. logtype
with their class reflected in it, and libraries use a lib. logtype.
Introduce two new macros:
- RTE_LOG_REGISTER_DEFAULT can be used when a single logtype is
used in a component. It is associated to the default name provided
by the build system,
- RTE_LOG_REGISTER_SUFFIX can be used when multiple logtypes are used,
and then the passed name is appended to the default name,
RTE_LOG_REGISTER is left untouched for existing external users
and for components that do not comply with the convention.
There is a new Meson variable log_prefix to adapt the default name
for baseband (pmd.bb.), bus (no pmd.) and mempool (no pmd.) classes.
Note: achieved with below commands + reverted change on net/bonding +
edits on crypto/virtio, compress/mlx5, regex/mlx5
$ git grep -l RTE_LOG_REGISTER drivers/ |
while read file; do
pattern=${file##drivers/};
class=${pattern%%/*};
pattern=${pattern#$class/};
drv=${pattern%%/*};
case "$class" in
baseband) pattern=pmd.bb.$drv;;
bus) pattern=bus.$drv;;
mempool) pattern=mempool.$drv;;
*) pattern=pmd.$class.$drv;;
esac
sed -i -e 's/RTE_LOG_REGISTER(\(.*\), '$pattern',/RTE_LOG_REGISTER_DEFAULT(\1,/' $file;
sed -i -e 's/RTE_LOG_REGISTER(\(.*\), '$pattern'\.\(.*\),/RTE_LOG_REGISTER_SUFFIX(\1, \2,/' $file;
done
$ git grep -l RTE_LOG_REGISTER lib/ |
while read file; do
pattern=${file##lib/};
pattern=lib.${pattern%%/*};
sed -i -e 's/RTE_LOG_REGISTER(\(.*\), '$pattern',/RTE_LOG_REGISTER_DEFAULT(\1,/' $file;
sed -i -e 's/RTE_LOG_REGISTER(\(.*\), '$pattern'\.\(.*\),/RTE_LOG_REGISTER_SUFFIX(\1, \2,/' $file;
done
Signed-off-by: David Marchand <david.marchand@redhat.com>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
The rte_ethdev_driver.h, rte_ethdev_vdev.h and rte_ethdev_pci.h files are
for drivers only and should be a private to DPDK and not installed.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Steven Webster <steven.webster@windriver.com>
The jumbo frame uses the 'RTE_ETHER_MAX_LEN' as boundary condition.
If the Ether overhead is larger than 18 when it supports VLAN tag,
that will cause the jumbo flag rx offload is wrong when MTU size is
'RTE_ETHER_MTU'.
This fix will normalize the boundary condition with 'RTE_ETHER_MTU'
and overhead even though current overhead is 18.
Fixes: 5d5589b0c8 ("net/enetc: support MTU update and jumbo frames")
Cc: stable@dpdk.org
Signed-off-by: Steve Yang <stevex.yang@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Queue stats are stored in 'struct rte_eth_stats' as array and array size
is defined by 'RTE_ETHDEV_QUEUE_STAT_CNTRS' compile time flag.
As a result of technical board discussion, decided to remove the queue
statistics from 'struct rte_eth_stats' in the long term.
Instead PMDs should represent the queue statistics via xstats, this
gives more flexibility on the number of the queues supported.
Currently queue stats in the xstats are filled by ethdev layer, using
some basic stats, when queue stats removed from basic stats the
responsibility to fill the relevant xstats will be pushed to the PMDs.
During the switch period, temporary 'RTE_ETH_DEV_AUTOFILL_QUEUE_XSTATS'
device flag is created. Initially all PMDs using xstats set this flag.
The PMDs implemented queue stats in the xstats should clear the flag.
When all PMDs switch to the xstats for the queue stats, queue stats
related fields from 'struct rte_eth_stats' will be removed, as well as
'RTE_ETH_DEV_AUTOFILL_QUEUE_XSTATS' flag.
Later 'RTE_ETHDEV_QUEUE_STAT_CNTRS' compile time flag also can be
removed.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Haiyue Wang <haiyue.wang@intel.com>
Acked-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Change eth_dev_stop_t return value from void to int.
Make eth_dev_stop_t implementations across all drivers to return
negative errno values if case of error conditions.
Signed-off-by: Ivan Ilchenko <ivan.ilchenko@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
When closing a port, it is supposed to be already stopped,
and marked as such with "dev_started" state zeroed by the stop API.
Resetting "dev_started" before calling the driver close operation
was hiding the case of not properly stopped port being closed.
The flag "dev_started" is not changed anymore in "rte_eth_dev_close()".
In case the "dev_stop" function is called from "dev_close",
bypassing "rte_eth_dev_stop()" API,
the "dev_started" state must be explicitly reset in the PMD
in order to keep the same behaviour.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Andrew Rybchenko <arybchenko@solarflare.com>
The secondary processes are not allowed to release shared resources.
Only process-private resources should be freed in a secondary process.
Most of the time, there is no process-private resource,
so the close operation is just forbidden in a secondary process.
After adding proper check in the port close functions,
some redundant checks in the device remove functions are dropped.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Reviewed-by: Rosen Xu <rosen.xu@intel.com>
Reviewed-by: Sachin Saxena <sachin.saxena@oss.nxp.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Liron Himi <lironh@marvell.com>
Reviewed-by: Haiyue Wang <haiyue.wang@intel.com>
Acked-by: Jeff Guo <jia.guo@intel.com>
Reviewed-by: Andrew Rybchenko <arybchenko@solarflare.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
The temporary flag RTE_ETH_DEV_CLOSE_REMOVE is removed.
It was introduced in DPDK 18.11 in order to give time for PMDs to migrate.
The old behaviour was to free only queues when closing a port.
The new behaviour is calling rte_eth_dev_release_port() which does
three more tasks:
- trigger event callback
- reset state and few pointers
- free all generic port resources
The private port resources must be released in the .dev_close callback.
The .remove callback should:
- call .dev_close callback
- call rte_eth_dev_release_port()
- free multi-port device shared resources
Despite waiting two years, some drivers have not migrated,
so they may hit issues with the incompatible new behaviour.
After sending emails, adding logs, and announcing the deprecation,
the only last solution is to declare these drivers as unmaintained:
ionic, liquidio, nfp
Below is a summary of what to implement in those drivers.
* The freeing of private port resources must be moved
from the ".remove(device)" function to the ".dev_close(port)" function.
* If a generic resource (.mac_addrs or .hash_mac_addrs) cannot be freed,
it must be set to NULL in ".dev_close" function to protect from
subsequent rte_eth_dev_release_port() freeing.
* Note 1:
The generic resources are freed in rte_eth_dev_release_port(),
after ".dev_close" is called in rte_eth_dev_close(), but not when
calling ".dev_close" directly from the ".remove" PMD function.
That's why rte_eth_dev_release_port() must still be called explicitly
from ".remove(device)" after calling the ".dev_close" PMD function.
* Note 2:
If a device can have multiple ports, the common resources must be freed
only in the ".remove(device)" function.
* Note 3:
The port is supposed to be in a stopped state when it is closed.
If it is not the case, it is free to the PMD implementation
how to react when trying to close a non-stopped port:
either try to stop it automatically or just return an error.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Reviewed-by: Liron Himi <lironh@marvell.com>
Reviewed-by: Haiyue Wang <haiyue.wang@intel.com>
Acked-by: Jeff Guo <jia.guo@intel.com>
Acked-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
With removal of old close behavior, the private
port resources must be released in the .dev_close callback.
Freeing of port private resources is moved from
the ".remove(device)" to the ".dev_close(port)" operation
Signed-off-by: Sachin Saxena <sachin.saxena@oss.nxp.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
The device operation .dev_close was returning void.
This driver interface is changed to return an int.
Note that the API rte_eth_dev_close() is still returning void,
although a deprecation notice is pending to change it as well.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Reviewed-by: Rosen Xu <rosen.xu@intel.com>
Reviewed-by: Sachin Saxena <sachin.saxena@oss.nxp.com>
Reviewed-by: Liron Himi <lironh@marvell.com>
Reviewed-by: Haiyue Wang <haiyue.wang@intel.com>
Acked-by: Jeff Guo <jia.guo@intel.com>
Reviewed-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Introduce the RTE_LOG_REGISTER macro to avoid the code duplication
in the logtype registration process.
It is a wrapper macro for declaring the logtype, registering it and
setting its level in the constructor context.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Acked-by: Adam Dybkowski <adamx.dybkowski@intel.com>
Acked-by: Sachin Saxena <sachin.saxena@nxp.com>
Acked-by: Akhil Goyal <akhil.goyal@nxp.com>
This was left to its default value. With the patch transactions are:
- coherent,
- do not allocate in downstream cache (there is none on LS1028a),
- merge surrounding data for BD writes,
- overwrite surrounding data for frame data writes.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Gagandeep Singh <g.singh@nxp.com>
The default value in hardware for the Rx MAC FIFO (@) is higher than it
should be and can lead to Rx lock-up under traffic.
Set it to the value recommended by hardware team, 1.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Gagandeep Singh <g.singh@nxp.com>
dpaaX is used to maintain a local copy of PA->VA translations.
Using the rte_mem_virt2iova or rte_mem_virt2phy is expensive. This
library is an attempt to reduce the overall cost associated with
this translation.
This patch enables this dpaaX library by populating a dpaaX's
table for PA to VA translation. This change will also help the
caam JR driver in PA to VA translation when used with enetc driver
over enetc supported SoCs.
Signed-off-by: Gagandeep Singh <g.singh@nxp.com>
for SGMII interfaces, there can be 0 value
written on MAC registers.
This patch set the random MAC address for those
interfaces.
Signed-off-by: Gagandeep Singh <g.singh@nxp.com>
enetc BD rings should be aligned to 128
instead of RTE_CACHE_LINE_SIZE.
Fixes: 469c6111a7 ("net/enetc: enable Rx and Tx")
Cc: stable@dpdk.org
Signed-off-by: Gagandeep Singh <g.singh@nxp.com>
Enabling/disabling of allmulticast mode is not always successful and
it should be taken into account to be able to handle it properly.
When correct return status is unclear from driver code, -EAGAIN is used.
Signed-off-by: Ivan Ilchenko <ivan.ilchenko@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Acked-by: Hyong Youb Kim <hyonkim@cisco.com>
Change return value of the callbacks from void to int. Make
implementations across all drivers return negative errno
values in case of error conditions.
Both callbacks are updated together because a large number of
drivers assign the same function to both callbacks.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Enabling/disabling of promiscuous mode is not always successful and
it should be taken into account to be able to handle it properly.
When correct return status is unclear from driver code, -EAGAIN is used.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Acked-by: Matan Azrad <matan@mellanox.com>
Acked-by: Hyong Youb Kim <hyonkim@cisco.com>
Change eth_dev_infos_get_t return value from void to int.
Make eth_dev_infos_get_t implementations across all drivers to return
negative errno values if case of error conditions.
Signed-off-by: Ivan Ilchenko <ivan.ilchenko@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add 'RTE_' prefix to defines:
- rename ETHER_ADDR_LEN as RTE_ETHER_ADDR_LEN.
- rename ETHER_TYPE_LEN as RTE_ETHER_TYPE_LEN.
- rename ETHER_CRC_LEN as RTE_ETHER_CRC_LEN.
- rename ETHER_HDR_LEN as RTE_ETHER_HDR_LEN.
- rename ETHER_MIN_LEN as RTE_ETHER_MIN_LEN.
- rename ETHER_MAX_LEN as RTE_ETHER_MAX_LEN.
- rename ETHER_MTU as RTE_ETHER_MTU.
- rename ETHER_MAX_VLAN_FRAME_LEN as RTE_ETHER_MAX_VLAN_FRAME_LEN.
- rename ETHER_MAX_VLAN_ID as RTE_ETHER_MAX_VLAN_ID.
- rename ETHER_MAX_JUMBO_FRAME_LEN as RTE_ETHER_MAX_JUMBO_FRAME_LEN.
- rename ETHER_MIN_MTU as RTE_ETHER_MIN_MTU.
- rename ETHER_LOCAL_ADMIN_ADDR as RTE_ETHER_LOCAL_ADMIN_ADDR.
- rename ETHER_GROUP_ADDR as RTE_ETHER_GROUP_ADDR.
- rename ETHER_TYPE_IPv4 as RTE_ETHER_TYPE_IPv4.
- rename ETHER_TYPE_IPv6 as RTE_ETHER_TYPE_IPv6.
- rename ETHER_TYPE_ARP as RTE_ETHER_TYPE_ARP.
- rename ETHER_TYPE_VLAN as RTE_ETHER_TYPE_VLAN.
- rename ETHER_TYPE_RARP as RTE_ETHER_TYPE_RARP.
- rename ETHER_TYPE_QINQ as RTE_ETHER_TYPE_QINQ.
- rename ETHER_TYPE_ETAG as RTE_ETHER_TYPE_ETAG.
- rename ETHER_TYPE_1588 as RTE_ETHER_TYPE_1588.
- rename ETHER_TYPE_SLOW as RTE_ETHER_TYPE_SLOW.
- rename ETHER_TYPE_TEB as RTE_ETHER_TYPE_TEB.
- rename ETHER_TYPE_LLDP as RTE_ETHER_TYPE_LLDP.
- rename ETHER_TYPE_MPLS as RTE_ETHER_TYPE_MPLS.
- rename ETHER_TYPE_MPLSM as RTE_ETHER_TYPE_MPLSM.
- rename ETHER_VXLAN_HLEN as RTE_ETHER_VXLAN_HLEN.
- rename ETHER_ADDR_FMT_SIZE as RTE_ETHER_ADDR_FMT_SIZE.
- rename VXLAN_GPE_TYPE_IPV4 as RTE_VXLAN_GPE_TYPE_IPV4.
- rename VXLAN_GPE_TYPE_IPV6 as RTE_VXLAN_GPE_TYPE_IPV6.
- rename VXLAN_GPE_TYPE_ETH as RTE_VXLAN_GPE_TYPE_ETH.
- rename VXLAN_GPE_TYPE_NSH as RTE_VXLAN_GPE_TYPE_NSH.
- rename VXLAN_GPE_TYPE_MPLS as RTE_VXLAN_GPE_TYPE_MPLS.
- rename VXLAN_GPE_TYPE_GBP as RTE_VXLAN_GPE_TYPE_GBP.
- rename VXLAN_GPE_TYPE_VBNG as RTE_VXLAN_GPE_TYPE_VBNG.
- rename ETHER_VXLAN_GPE_HLEN as RTE_ETHER_VXLAN_GPE_HLEN.
Do not update the command line library to avoid adding a dependency to
librte_net.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add 'rte_' prefix to structures:
- rename struct ether_addr as struct rte_ether_addr.
- rename struct ether_hdr as struct rte_ether_hdr.
- rename struct vlan_hdr as struct rte_vlan_hdr.
- rename struct vxlan_hdr as struct rte_vxlan_hdr.
- rename struct vxlan_gpe_hdr as struct rte_vxlan_gpe_hdr.
Do not update the command line library to avoid adding a dependency to
librte_net.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Support for SXGMII port has been enabled. It will
depends on boot loader information passed through IERB.
Signed-off-by: Gagandeep Singh <g.singh@nxp.com>
First configure ring with BDs properly then enable
the ring.
Fixes: 469c6111a7 ("net/enetc: enable Rx and Tx")
Cc: stable@dpdk.org
Signed-off-by: Gagandeep Singh <g.singh@nxp.com>
This is a clean-up of common ethdev data freeing.
All data freeing are moved to rte_eth_dev_release_port()
and done only in case of primary process.
It is probably fixing some memory leaks for PMDs which were
not freeing all data.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Andrew Rybchenko <arybchenko@solarflare.com>
