A new hook function is added and called inside the PMDs at the end
of the device probing:
- in primary process, after allocating, init and config
- in secondary process, after attaching and local init
This new function is almost empty for now.
It will be used later to add some post-initialization processing.
For the PMDs calling the helpers rte_eth_dev_create() or
rte_eth_dev_pci_generic_probe(), the hook rte_eth_dev_probing_finish()
is called from here, and not in the PMD itself.
Note that the helper rte_eth_dev_create() could be used more,
especially for vdevs, avoiding some code duplication in PMDs.
Cc: stable@dpdk.org
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Reviewed-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
This patch check if a input requested offloading is valid or not.
Any reuqested offloading must be supported in the device capabilities.
Any offloading is disabled by default if it is not set in the parameter
dev_conf->[rt]xmode.offloads to rte_eth_dev_configure() and
[rt]x_conf->offloads to rte_eth_[rt]x_queue_setup().
If any offloading is enabled in rte_eth_dev_configure() by application,
it is enabled on all queues no matter whether it is per-queue or
per-port type and no matter whether it is set or cleared in
[rt]x_conf->offloads to rte_eth_[rt]x_queue_setup().
If a per-queue offloading hasn't be enabled in rte_eth_dev_configure(),
it can be enabled or disabled for individual queue in
ret_eth_[rt]x_queue_setup().
A new added offloading is the one which hasn't been enabled in
rte_eth_dev_configure() and is reuqested to be enabled in
rte_eth_[rt]x_queue_setup(), it must be per-queue type,
otherwise trigger an error log.
The underlying PMD must be aware that the requested offloadings
to PMD specific queue_setup() function only carries those
new added offloadings of per-queue type.
This patch can make above such checking in a common way in rte_ethdev
layer to avoid same checking in underlying PMD.
This patch assumes that all PMDs in 18.05-rc2 have already
converted to offload API defined in 17.11 . It also assumes
that all PMDs can return correct offloading capabilities
in rte_eth_dev_infos_get().
In the beginning of [rt]x_queue_setup() of underlying PMD,
add offloads = [rt]xconf->offloads |
dev->data->dev_conf.[rt]xmode.offloads; to keep same as offload API
defined in 17.11 to avoid upper application broken due to offload
API change.
PMD can use the info that input [rt]xconf->offloads only carry
the new added per-queue offloads to do some optimization or some
code change on base of this patch.
Signed-off-by: Wei Dai <wei.dai@intel.com>
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Some DPDK applications wrongly assume these requirements:
- no hotplug, i.e. ports are never detached
- all allocated ports are available to the application
Such application iterates over ports by its own mean.
The most common pattern is to request the port count and
assume ports with index in the range [0..count[ can be used.
There are three consequences when using such wrong design:
- new ports having an index higher than the port count won't be seen
- old ports being detached (RTE_ETH_DEV_UNUSED) can be seen as ghosts
- failsafe sub-devices (RTE_ETH_DEV_DEFERRED) will be seen by the application
Such mistake will be less common with growing hotplug awareness.
All applications and examples inside this repository - except testpmd -
must be fixed to use the iterator RTE_ETH_FOREACH_DEV.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Change the prototype and the behavior of dev_ops->eth_mac_addr_set(): a
return code is added to notify the caller (librte_ether) if an error
occurred in the PMD.
The new default MAC address is now copied in dev->data->mac_addrs[0]
only if the operation is successful.
The patch also updates all the PMDs accordingly.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Acked-by: Andrew Rybchenko <arybchenko@solarflare.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Acked-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
The name "mrvl" for Marvell PMD driver for PPv2 Marvell PPv2
(Packet Processor v2) 1/10 Gbps adapter is too generic and causes
problem for adding new PMD drivers for other Marvell devices.
Changed to "mvpp2" for specific Marvell PPv2 PMD.
This patch doesn't introduce any change except renaming.
Signed-off-by: Natalie Samsonov <nsamsono@marvell.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
