The new 5-tuple swap engine swaps:
source and destination mac address,
source and destination address in ipv4/ipv6,
source and destination port in UDP/TCP.
The forwarding engine will parse each layer
and swap it, and will stop when the next
layer doesn't match.
The mentioned headers of ICMP/ARP/Multicast
packets will be swapped as well according to
matching layers.
usage: --forward-mode=5tswap
Signed-off-by: Shiri Kuzin <shirik@mellanox.com>
Acked-by: Matan Azrad <matan@mellanox.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
One new cmdline option `--rx-mq-mode` is added in order to have the
possibility to check whether PMD handle the mq mode correctly or not.
The reason is some NICs need to do different settings based on different
RX mq mode, i.e RSS or not.
With this support in testpmd, the above scenario can be tested easily.
Signed-off-by: Xiaoyu Min <jackmin@mellanox.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
Currently, there is no way to check the aging event or to get the
current aged flows in testpmd, this patch include those implements, it's
included:
- Add new item "flow_aged" to the current print event command arguments.
- Add new command to list all aged flows, meanwhile, we can set
parameter to destroy it.
Signed-off-by: Dong Zhou <dongz@mellanox.com>
Acked-by: Matan Azrad <matan@mellanox.com>
Acked-by: Ori Kam <orika@mellanox.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
The EAL options and app-specific options are separated
with double dashes.
The help of testpmd, test-acl and pdump were missing
the dashes after EAL options.
Note: testpmd was completely missing the EAL options.
Fixes: af75078fece3 ("first public release")
Fixes: 26c057ab6c45 ("acl: new test-acl application")
Fixes: b2854d5317e8 ("app/pdump: support multi-core capture")
Cc: stable@dpdk.org
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
In current version, we are setting the ports
using portmask. With portmask, we can use only
up to 64 ports. This portlist option enables the user
to use more than 64 ports.
Now we can specify the ports in 2 different ways
- Using portmask (-p [0x]nnn): mask must be in hex format
- Using portlist in the following format
--portlist <p1>[-p2][,p3[-p4],...]
--portmask 0x2 is same as --portlist 1
--portmask 0x3 is same as --portlist 0-1
Signed-off-by: Hariprasad Govindharajan <hariprasad.govindharajan@intel.com>
Acked-by: Anatoly Burakov <anatoly.burakov@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Reviewed-by: Herakliusz Lipiec <herakliusz.lipiec@intel.com>
The new mbuf pool type is added to testpmd. To engage the
mbuf pool with externally attached data buffers the parameter
"--mp-alloc=xbuf" should be specified in testpmd command line.
The objective of this patch is just to test whether mbuf pool
with externally attached data buffers works OK. The memory for
data buffers is allocated from DPDK memory, so this is not
"true" external memory from some physical device (this is
supposed the most common use case for such kind of mbuf pool).
The user should be aware that not all drivers support the mbuf
with EXT_ATTACHED_BUF flags set in newly allocated mbuf (many
PMDs just overwrite ol_flags field and flag value is getting
lost).
Signed-off-by: Viacheslav Ovsiienko <viacheslavo@mellanox.com>
Acked-by: Olivier Matz <olivier.matz@6wind.com>
We currently do not check that a non option string has been passed to
testpmd.
Example:
$ ./master/app/testpmd --no-huge -m 512 --vdev net_null0 \
--vdev net_null1 -- -i nb-cores=2 --total-num-mbuf 2048
[...]
testpmd> show config fwd
io packet forwarding - ports=2 - cores=1 - streams=2 - NUMA support
enabled, MP allocation mode: native
Logical Core 1 (socket 0) forwards packets on 2 streams:
RX P=0/Q=0 (socket 0) -> TX P=1/Q=0 (socket 0) peer=02:00:00:00:00:01
RX P=1/Q=0 (socket 0) -> TX P=0/Q=0 (socket 0) peer=02:00:00:00:00:00
Here nb-cores=2 is just ignored, while the (probably sleepy) user did not
notice this.
Validate that all strings passed to testpmd are part of a known option.
After this patch:
$ ./master/app/testpmd --no-huge -m 512 --vdev net_null0 \
--vdev net_null1 -- -i nb-cores=2 --total-num-mbuf 2048
[...]
Invalid parameter: nb-cores=2
EAL: Error - exiting with code: 1
Cause: Command line incorrect
While at it, when passing an unknown option, print the string that gets
refused by getopt_long to help the user.
Fixes: af75078fece3 ("first public release")
Cc: stable@dpdk.org
Signed-off-by: David Marchand <david.marchand@redhat.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
This patch implements use of the API for LRO aggregated packet
max size.
It adds command-line and runtime commands to configure this value,
and adds option to show the supported value.
Documentation is updated accordingly.
Signed-off-by: Dekel Peled <dekelp@mellanox.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Matan Azrad <matan@mellanox.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
This commit introduce the hairpin queues to the testpmd.
the hairpin queue is configured using --hairpinq=<n>
the hairpin queue adds n queue objects for both the total number
of TX queues and RX queues.
The connection between the queues are 1 to 1, first Rx hairpin queue
will be connected to the first Tx hairpin queue
Signed-off-by: Ori Kam <orika@mellanox.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@mellanox.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
The testpmd --help option did not show all possible choices for port
topology previously. The loop topology option is now added.
Fixes: 3e2006d6186c ("app/testpmd: add loopback topology")
Cc: stable@dpdk.org
Signed-off-by: Ciara Power <ciara.power@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add eth_dev_info_get_print_err() which is a wrapper for
rte_eth_dev_info_get() printing error if rte_eth_dev_info_get()
fails and returning its status code.
Signed-off-by: Ivan Ilchenko <ivan.ilchenko@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
Some configuration options can not be tested properly with testpmd
because it automatically starts all ports. This makes it harder
to test driver handling of configuration options:
(for example rx_deferred_start).
Add new command line flag --disable-device-start which skips
the device start. The port can then be started manually later.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
The cmdline_parse_ether_addr does not need to be used everywhere
in testpmd. Can use rte_ether_unformat_addr instead.
As an added bonus it eliminates some code for copying.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
Add 'RTE_' prefix to defines:
- rename ETHER_ADDR_LEN as RTE_ETHER_ADDR_LEN.
- rename ETHER_TYPE_LEN as RTE_ETHER_TYPE_LEN.
- rename ETHER_CRC_LEN as RTE_ETHER_CRC_LEN.
- rename ETHER_HDR_LEN as RTE_ETHER_HDR_LEN.
- rename ETHER_MIN_LEN as RTE_ETHER_MIN_LEN.
- rename ETHER_MAX_LEN as RTE_ETHER_MAX_LEN.
- rename ETHER_MTU as RTE_ETHER_MTU.
- rename ETHER_MAX_VLAN_FRAME_LEN as RTE_ETHER_MAX_VLAN_FRAME_LEN.
- rename ETHER_MAX_VLAN_ID as RTE_ETHER_MAX_VLAN_ID.
- rename ETHER_MAX_JUMBO_FRAME_LEN as RTE_ETHER_MAX_JUMBO_FRAME_LEN.
- rename ETHER_MIN_MTU as RTE_ETHER_MIN_MTU.
- rename ETHER_LOCAL_ADMIN_ADDR as RTE_ETHER_LOCAL_ADMIN_ADDR.
- rename ETHER_GROUP_ADDR as RTE_ETHER_GROUP_ADDR.
- rename ETHER_TYPE_IPv4 as RTE_ETHER_TYPE_IPv4.
- rename ETHER_TYPE_IPv6 as RTE_ETHER_TYPE_IPv6.
- rename ETHER_TYPE_ARP as RTE_ETHER_TYPE_ARP.
- rename ETHER_TYPE_VLAN as RTE_ETHER_TYPE_VLAN.
- rename ETHER_TYPE_RARP as RTE_ETHER_TYPE_RARP.
- rename ETHER_TYPE_QINQ as RTE_ETHER_TYPE_QINQ.
- rename ETHER_TYPE_ETAG as RTE_ETHER_TYPE_ETAG.
- rename ETHER_TYPE_1588 as RTE_ETHER_TYPE_1588.
- rename ETHER_TYPE_SLOW as RTE_ETHER_TYPE_SLOW.
- rename ETHER_TYPE_TEB as RTE_ETHER_TYPE_TEB.
- rename ETHER_TYPE_LLDP as RTE_ETHER_TYPE_LLDP.
- rename ETHER_TYPE_MPLS as RTE_ETHER_TYPE_MPLS.
- rename ETHER_TYPE_MPLSM as RTE_ETHER_TYPE_MPLSM.
- rename ETHER_VXLAN_HLEN as RTE_ETHER_VXLAN_HLEN.
- rename ETHER_ADDR_FMT_SIZE as RTE_ETHER_ADDR_FMT_SIZE.
- rename VXLAN_GPE_TYPE_IPV4 as RTE_VXLAN_GPE_TYPE_IPV4.
- rename VXLAN_GPE_TYPE_IPV6 as RTE_VXLAN_GPE_TYPE_IPV6.
- rename VXLAN_GPE_TYPE_ETH as RTE_VXLAN_GPE_TYPE_ETH.
- rename VXLAN_GPE_TYPE_NSH as RTE_VXLAN_GPE_TYPE_NSH.
- rename VXLAN_GPE_TYPE_MPLS as RTE_VXLAN_GPE_TYPE_MPLS.
- rename VXLAN_GPE_TYPE_GBP as RTE_VXLAN_GPE_TYPE_GBP.
- rename VXLAN_GPE_TYPE_VBNG as RTE_VXLAN_GPE_TYPE_VBNG.
- rename ETHER_VXLAN_GPE_HLEN as RTE_ETHER_VXLAN_GPE_HLEN.
Do not update the command line library to avoid adding a dependency to
librte_net.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
This patch changes what testpmd uses as IP addresses when
run in transmit only mode. The old code was using
192.168.0.1 -> 192.168.0.2
but these addresses are reserved for private Internet by RFC 1918.
The new code uses 192.18.0.1 and 192.18.0.2 which are on the
subnet reserved for performance testing by RFC 2544.
New command line option allows the user to pick any other src/dst
address desired.
Notice: this changes the default IP address for transmit only.
It may cause some user who has hardcoded network addresses to report
a regression.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
providing a command line parameter to set the mempool flags accordingly.
This mode is relevant only when creating an empty mempool and then
populating with memory.
Signed-off-by: Shahaf Shuler <shahafs@mellanox.com>
Acked-by: Anatoly Burakov <anatoly.burakov@intel.com>
Testpmd can generate multiple flows without taking much cost and this
could be a simple traffic generator for developer's quick tests.
If "--txonly-multi-flow" is specified in the command line, IP source
address is varied to generate multiple flows.
Signed-off-by: Yongseok Koh <yskoh@mellanox.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
If user explicitly requested memory to be allocated from a socket via
`port-numa-config` and `ring-numa-config`, and if that socket is
valid, add that socket into socket_ids[] so that mempool allocated for
that socket.
Fixes: dbfb8ec7094c ("app/testpmd: optimize mbuf pool allocation")
Cc: stable@dpdk.org
Suggested-by: Ferruh Yigit <ferruh.yigit@intel.com>
Signed-off-by: Phil Yang <phil.yang@arm.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
This adds a new forwarding mode to testpmd to simulate
more realistic behavior of a guest machine engaged in receiving
and sending packets performing Virtual Network Function (VNF).
The goal is to enable a simple way of measuring performance impact on
cache and memory footprint utilization from various VNF co-located on
the same host machine. For this it does:
* Buffer packets in a FIFO:
Create a fifo to buffer received packets. Once it flows over put
those packets into the actual tx queue. The fifo is created per tx
queue and its size can be set with the --noisy-tx-sw-buffer-flushtime
commandline parameter.
A second commandline parameter is used to set a timeout in
milliseconds after which the fifo is flushed.
--noisy-tx-sw-buffer-size [packet numbers]
Keep the mbuf in a FIFO and forward the over flooding packets from the
FIFO. This queue is per TX-queue (after all other packet processing).
--noisy-tx-sw-buffer-flushtime [delay]
Flush the packet queue if no packets have been seen during
[delay]. As long as packets are seen, the timer is reset.
Add several options to simulate route lookups (memory reads) in tables
that can be quite large, as well as route hit statistics update.
These options simulates the while stack traversal and
will trash the cache. Memory access is random.
* simulate route lookups:
Allocate a buffer and perform reads and writes on it as specified by
commandline options:
--noisy-lkup-memory [size]
Size of the VNF internal memory (MB), in which the random
read/write will be done, allocated by rte_malloc (hugepages).
--noisy-lkup-num-writes [num]
Number of random writes in memory per packet should be
performed, simulating hit-flags update. 64 bits per write,
all write in different cache lines.
--noisy-lkup-num-reads [num]
Number of random reads in memory per packet should be
performed, simulating FIB/table lookups. 64 bits per read,
all write in different cache lines.
--noisy-lkup-num-reads-writes [num]
Number of random reads and writes in memory per packet should
be performed, simulating stats update. 64 bits per read-write, all
reads and writes in different cache lines.
Signed-off-by: Jens Freimann <jfreimann@redhat.com>
Acked-by: Kevin Traynor <ktraynor@redhat.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
Currently, mempools can only be allocated either using native
DPDK memory, or anonymous memory. This patch will add two new
methods to allocate mempool using external memory (regular or
hugepage memory), and add documentation about it to testpmd
user guide.
It adds a new flag "--mp-alloc", with four possible values:
native (use regular DPDK allocator), anon (use anonymous
mempool), xmem (use externally allocated memory area), and
xmemhuge (use externally allocated hugepage memory area). Old
flag "--mp-anon" is kept for compatibility.
All external memory is allocated using the same external heap,
but each will allocate and add a new memory area.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
Removed DEV_RX_OFFLOAD_CRC_STRIP offload flag.
Without any specific Rx offload flag, default behavior by PMDs is to
strip CRC.
PMDs that support keeping CRC should advertise DEV_RX_OFFLOAD_KEEP_CRC
Rx offload capability.
Applications that require keeping CRC should check PMD capability first
and if it is supported can enable this feature by setting
DEV_RX_OFFLOAD_KEEP_CRC in Rx offload flag in rte_eth_dev_configure()
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Tomasz Duszynski <tdu@semihalf.com>
Acked-by: Shahaf Shuler <shahafs@mellanox.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Acked-by: Jan Remes <remes@netcope.com>
Acked-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Acked-by: Hyong Youb Kim <hyonkim@cisco.com>
If "--disable-crc-strip" testpmd parameter issued, it removes the
DEV_RX_OFFLOAD_CRC_STRIP flag.
With introduction of new DEV_RX_OFFLOAD_KEEP_CRC offload flag, this
flag also should be set when this parameter issued.
Fixes: 70815c9ecadd ("ethdev: add new offload flag to keep CRC")
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
There are several cases of an invalid port data access that causes the
printing of all the valid ports, for example, when the user asks to
receive a port information of an invalid port.
Wrongly, the port with id 0 is printed in all the above described
cases, regardless of its validity.
Print port 0 only if it is valid as done for the rest of the ports.
Fixes: af75078fece3 ("first public release")
Fixes: b6ea6408fbc7 ("ethdev: store numa_node per device")
Fixes: edab33b1c01d ("app/testpmd: support port hotplug")
Cc: stable@dpdk.org
Signed-off-by: Matan Azrad <matan@mellanox.com>
Add two new command-line parameters for either enabling or
disabling locking all memory at app startup.
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Signed-off-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Add VXLAN-GPE support to csum forwarding engine and rte flow.
Signed-off-by: Xueming Li <xuemingl@mellanox.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
The optimal values of several transmission & reception related
parameters, such as burst sizes, descriptor ring sizes, and number
of queues, varies between different network interface devices. This
patch allows testpmd to make use of per-PMD tuned parameter values.
Signed-off-by: Remy Horton <remy.horton@intel.com>
Acked-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Use testpmd for example, to show how an application uses device event
APIs to monitor the hotplug events, including both hot removal event
and hot insertion event.
The process is that, testpmd first enable hotplug by below commands,
E.g. ./build/app/testpmd -c 0x3 --n 4 -- -i --hot-plug
then testpmd starts the device event monitor by calling the new API
(rte_dev_event_monitor_start) and register the user's callback by call
the API (rte_dev_event_callback_register), when device being hotplug
insertion or hotplug removal, the device event monitor detects the event
and call user's callbacks, user could process the event in the callback
accordingly.
This patch only shows the event monitoring, device attach/detach would
not be involved here, will add from other hotplug patch set.
Signed-off-by: Jeff Guo <jia.guo@intel.com>
Reviewed-by: Jianfeng Tan <jianfeng.tan@intel.com>
Since we have support for the strlcpy function in DPDK, replace all
instances where a string is copied using snprintf.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Removed the hardcoded preconfigured Rx VLAN offload configuration
from testpmd and changed the Rx offload command line parameters from
disable to enable.
It has been decided by the Technical Board that testers who wish to
use these offloads will now have to explicitly write them in the
command-line when running testpmd.
The agreement is to keep two exceptions enabled by default in 18.02:
Rx CRC strip and Tx fast free.
Motivation:
Some PMDs such at the mlx4 may not implement all the offloads.
After the offload API rework assuming no offload is enabled by default,
commit ce17eddefc20 ("ethdev: introduce Rx queue offloads API")
commit cba7f53b717d ("ethdev: introduce Tx queue offloads API") trying
to enable a not supported offload is clearly an error which will cause
configuration failing.
Considering that testpmd is an application to test the PMD, it should
not fail on a configuration which was not explicitly requested.
The behavior of this test application is then turned to an opt-in
model.
Signed-off-by: Moti Haimovsky <motih@mellanox.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
If an invalid number of TX queues is configured from testpmd run-time
command like "port config all txq number" or from --txq in the command
to start testpmd, the global variable nb_txq is updated by this invalid
value without this patch. It may cause testpmd crash. This patch refuses
invalid txq setting and keeps its last correct value.
Fixes: ce8d561418d4 ("app/testpmd: add port configuration settings")
Cc: stable@dpdk.org
Signed-off-by: Wei Dai <wei.dai@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Tested-by: Yuan Peng <yuan.peng@intel.com>
If an invalid number of RX queues is configured from testpmd run-time
command like "port config all rxq number" or from --rxq in the command
to start testpmd, the global variable nb_rxq is updated by this invalid
value without this patch. It may cause testpmd crash. This patch refuses
invalid rxq setting and keeps its last correct value.
Fixes: ce8d561418d4 ("app/testpmd: add port configuration settings")
Cc: stable@dpdk.org
Signed-off-by: Wei Dai <wei.dai@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Tested-by: Yuan Peng <yuan.peng@intel.com>
There are new Ethernet device events - NEW and DESTROY, and new option
to register all ports by one call.
Adjust application to aforementioned changes.
Signed-off-by: Matan Azrad <matan@mellanox.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Since testpmd is now using the new Ethdev offloads API and there is
a way configure each of the tx offloads from CLI or command line,
there is no need for the txqflags configuration anymore.
Signed-off-by: Shahaf Shuler <shahafs@mellanox.com>
Acked-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch adds command line option to set hex value for the ports Tx
offloads flags.
Signed-off-by: Shahaf Shuler <shahafs@mellanox.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Ethdev Rx offloads API has changed since:
commit ce17eddefc20 ("ethdev: introduce Rx queue offloads API")
Convert the application to use the new API. The is no functionality
changes rather simple conversion of the flags.
Signed-off-by: Shahaf Shuler <shahafs@mellanox.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Replace the BSD license header with the SPDX tag for files
with only an Intel copyright on them.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
The memzone header is often included without good reason.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
in parse_ringnuma_config/parse_portnuma_config functions, port_id
should be less than RTE_MAX_ETHPORTS, but port_id_is_invalid check
assumes that port_id may be RTE_PORT_ALL (65535).
Also fix port_id storage size.
Fixes: 4468635fdd04 ("app/testpmd: forbid actions on invalid port")
Cc: stable@dpdk.org
Signed-off-by: Li Han <han.li1@zte.com.cn>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Extend port_id definition from uint8_t to uint16_t in lib and drivers
data structures, specifically rte_eth_dev_data. Modify the APIs,
drivers and app using port_id at the same time.
Fix some checkpatch issues from the original code and remove some
unnecessary cast operations.
release_17_11 and deprecation docs have been updated in this patch.
Signed-off-by: Zhiyong Yang <zhiyong.yang@intel.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Providing this parameter requests flow API isolated mode on all ports at
initialization time. It ensures all traffic is received through the
configured flow rules only (see flow command).
Ports that do not support this mode are automatically discarded.
Signed-off-by: Vasily Philipov <vasilyf@mellanox.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Add parameter to print port statistics periodically
(disabled by default), if interactive mode is not enabled.
This is useful to allow the user to see port statistics
without having to get into the internal command line.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
