Since the built driver filenames have changed in DPDK 20.11, we need to
update the driver doc to match.
Most drivers start their section with the driver filename highlighted in
bold, while a number were missing the highlight. When updating the names,
add the markers for bold text to any missing it, so as to have things more
consistent.
Fixes: a20b2c01a7 ("build: standardize component names and defines")
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Reviewed-by: David Marchand <david.marchand@redhat.com>
Reviewed-by: Rosen Xu <rosen.xu@intel.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Make is no longer supported for compiling DPDK, references are now
removed in the documentation.
Signed-off-by: Ciara Power <ciara.power@intel.com>
Reviewed-by: Bruce Richardson <bruce.richardson@intel.com>
Reviewed-by: Igor Russkikh <irusskikh@marvell.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Reviewed-by: Harman Kalra <hkalra@marvell.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Hyong Youb Kim <hyonkim@cisco.com>
Rather than using linuxapp and bsdapp everywhere, we can change things to
use the, more readable, terms "linux" and "freebsd" in our build configs.
Rather than renaming the configs we can just duplicate the existing ones
with the new names using symlinks, and use the new names exclusively
internally. ["make showconfigs" also only shows the new names to keep the
list short] The result is that backward compatibility is kept fully but any
new builds or development can be done using the newer names, i.e. both
"make config T=x86_64-native-linuxapp-gcc" and "T=x86_64-native-linux-gcc"
work.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Some drivers (mlx, mvpp2, sfc) support the flow isolated mode,
but the feature was not advertised.
A reference to the feature description is added for each driver.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Shahaf Shuler <shahafs@mellanox.com>
A doc page (.rst file) can be referenced with :doc: syntax
instead of :ref: to .. anchor.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Shahaf Shuler <shahafs@mellanox.com>
Don't use .svg extension on ..figure references. PDF versions of
the documents use .png images generated from the .svg images.
Fixes: 0ba610ca1d ("net/mvpp2: document MTR and TM usage")
Signed-off-by: Dan Gora <dg@adax.com>
Trivial pelling errors found by codespell.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Marko Kovacevic <marko.kovacevic@intel.com>
Document MTR (metering) and TM (traffic management) usage plus
do some small updates here and there.
Signed-off-by: Natalie Samsonov <nsamsono@marvell.com>
This patch introduces necessary changes required by MUSDK 18.09 library.
* As of MUSDK 18.09, pp2_cookie_t is no longer available. Now
RX descriptor cookie is defined as plain u64 so existing cast
is no longer valid.
* MUSDK 18.09 increased number of available bpools (buffer hw pools) by
introducing dma regions support. Update mvpp2 driver accordingly.
* replace MV_NET_IP4_F_TOS with MV_NET_IP4_F_DSCP
Before this patch, API allowed to configure a classification rule
according to IPv4 TOS, which was not supported in classifier. This patch
fixes this by using proper field.
* use 48 bit address mask
We cannot get pointers exceeding 48 bits thus using 48 bit
mask for extracting higher IOVA address bits is enough.
Signed-off-by: Natalie Samsonov <nsamsono@marvell.com>
Signed-off-by: Yuval Caduri <cyuval@marvell.com>
Signed-off-by: Tomasz Duszynski <tdu@semihalf.com>
Reviewed-by: Shlomi Gridish <sgridish@marvell.com>
Reviewed-by: Alan Winkowski <walan@marvell.com>
Reviewed-by: Liron Himi <lironh@marvell.com>
Change QoS configuration file syntax for port's default policer
setup.
Since default policer configuration is performed before
any other policer configuration we can pick a default id.
This simplifies default policer configuration since user
no longer has to choose ids from range [0, PP2_CLS_PLCR_NUM].
Explicitly document values for rate_limit_enable field.
Signed-off-by: Tomasz Duszynski <tdu@semihalf.com>
Signed-off-by: Natalie Samsonov <nsamsono@marvell.com>
Reviewed-by: Liron Himi <lironh@marvell.com>
The name "mrvl" for Marvell PMD driver for PPv2 Marvell PPv2
(Packet Processor v2) 1/10 Gbps adapter is too generic and causes
problem for adding new PMD drivers for other Marvell devices.
Changed to "mvpp2" for specific Marvell PPv2 PMD.
This patch doesn't introduce any change except renaming.
Signed-off-by: Natalie Samsonov <nsamsono@marvell.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
