Multiple IES API resets can cause a race condition where the mailbox
interrupt request bits can be cleared before being handled. This can
leave certain mailbox messages from the PF to be untreated and the PF
will enter in some inactive state. If this situation occurs, the IES API
will initiate a mailbox version reset which, then, trigger a mailbox
state change. Once this mailbox transition occurs (from OPEN to CONNECT
state), a request for reset will be returned.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Other shared code bases are planning on using
IS_MULTICAST_ETHER_ADDR and friends without leaving the driver
name in the macro.
Remove reference to FM10K here so that we can re-use the specific
compat flags from Linux.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Avoid potential FUM fault errors on a VF when updating MAC address
and VLAN information. Only use the register flow when the mailbox is
disconnected, by checking if the enqueue_tx returns
FM10K_MBX_ERR_NO_MBX. If the mailbox message can be sent, there is no
reason to bother with the register writes which are only intended to
be used during VF driver initialization.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Don't report FM10K_ERR_REQUESTS_PENDING when we fail to disable queues
within the timeout. This can occur due to a hardware Tx hang, or when
the switch ethernet fabric is resetting while we are transmitting
traffic. It can sometimes take up to 500ms before the Tx DMA engine
gives up. Instead, just skip the DMA engine check and perform
a data-path reset anyways. Add a statistic counter to keep track of the
number of resets occurring while we have pending DMA on the rings.
In order to prevent having to assign err = FM10K_SUCCESS, re-order the
last few items of the reset_hw_pf function so that we don't perform
"return err" at the end.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
If the fm10k interface is brought up, but the switch manager software is
not running, the driver will continuously request the lport map every
few seconds in the base driver watchdog routine. Eventually after
several minutes the switch mailbox Tx fifo will fill up and the mailbox
will timeout, resulting in a reset. This reset will appear as if for no
reason, and occurs regularly every few minutes until the switch manager
software is loaded.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
The VF uses a multi-bit update request to clear unused VLANs whenever it
resets. However, an accident in a previous refactor broke multi-bit
updates for VFs, due to misreading a comment in fm10k_vf.c and
attempting to reduce code duplication. The problem occurs because
a multi-bit request has a non-zero length, and the PF would simply drop
any request with the upper 16 bits set. In addition, a multi-bit vlan
update does not have a concept for "VLAN 0" as the single bit update
does.
A previous revision of this patch resolved the issue by simply removing
the upper 16 bit check and the iov_select_vid checks. However, this would
remove the checks for default VID and for ensuring no other VLANs can be
enabled except pf_vid when it has been set. To resolve that issue, this
revision uses the iov_select_vid when we have a single-bit update, and
denies any multi-bit update when the VLAN was administratively set by
the PF. This should be ok since the PF properly updates VLAN_TABLE when
it assigns the PF vid. This ensures that requests to add or "remove" the
PF vid work as expected, but a rogue VF could not use the multi-bit
update as a loophole to attempt receiving traffic on other VLANs.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
The original comment may be read incorrectly as referring to checking
the *entire* length is zero. However, it merely checks only the reserved
bits of both length and reserved in a small amount of code. Update the
comment to indicate this is a clever trick and clearly spell out that it
only checks the reserve bits.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Use a new #define FM10K_VLAN_OVERRIDE even though we're using
the exact same bit. The reason for this is clarity in the code,
otherwise you can read FM10K_VLAN_CLEAR and think it should be
removed. Also add a comment explaining why the FM10K_VLAN_OVERRIDE
bit is set.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
The diagram represents bit layout of the multi-bit VLAN update
message format. Re-draw the numbers using base 8, and mark the
bit values every 8 bits at the top. This should make it more
easy to grasp the table quickly.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Add FM10K_PF_ATTR_ID_ERR, since it is possible for the switch manager
to send out an error message indicating status of the LPORT_MAP due to
zero allocated bandwidth.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Clean up the logic in fm10k_tlv_attr_parse, we
should not reply on that FM10K_NOT_IMPLEMENTED is
greater than zero, as this can easily cause confusion.
The patch also correct a minor document error.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Deleting lport when multicast mod is configured to
FM10K_XCAST_MODE_ALLMULTI or FM10K_XCAST_MODE_PROMISC will
result in generating orphaned multicast-group entries in the
switch manager.
Before deleting the lport, reset multicast mode to
FM10K_XCAST_MODE_NONE to flush out these multicast-group
entries.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Replace the raw I/O device memory read/write access with eal
abstraction for I/O device memory read/write access to fix
portability issues across different architectures.
CC: Jing Chen <jing.d.chen@intel.com>
Signed-off-by: Santosh Shukla <santosh.shukla@caviumnetworks.com>
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Remove the unused element request_lport_map in struct fm10k_mac_ops.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Tested-by: Heng Ding <hengx.ding@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
Some cleanups to better reflect the code that was actually pushed out to
the upstream Linux community.
Among the above cleanups, a few macros such as FM10K_RXINT_TIMER_SHIFT are
removed, but they are needed in dpdk/fm10k, so we have to put all these
necessary macros into fm10k_osdep.h.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Tested-by: Heng Ding <hengx.ding@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
Per comments from an upstream kernel patch, and looking at how TLV
LE_STRUCT code works, we actually want these structures to be 4byte
aligned, not 1byte aligned.
In practice, 1byte alignment has worked so far because all our
structures end up being a multiple of 4. But if a future TLV
structure were added that had a u8 or similar sticking on the end things
would break. Fix this by using 4byte alignment which will prevent the
TLV LE_STRUCT code from breaking. Update the comment explaining that we
need 4byte alignment of our structures.
Fixes: 925c862cbc ("fm10k/base: pack TLV overlay structures")
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Tested-by: Heng Ding <hengx.ding@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
The comment for fm10k_iov_msg_lport_state_pf was changed during
review of kernel driver, and the new wording is slightly clearer.
Re-write the comment in base code based on this new wording.
Fix a number of mailbox comment issues with function header comments,
lower-case acronyms (i.e. FIFO, TLV), incorrect function names in
DEBUGFUNC(), duplicate comments and a stubbed-out header comment for
fm10k_sm_mbx_init.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Tested-by: Heng Ding <hengx.ding@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
The vid variable name is shorthand for VLAN ID, so we should use this in
comments explaining what is happening.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Tested-by: Heng Ding <hengx.ding@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
The Linux Kernel provides the OS a call "pcie_get_minimum_link" which
can crawl the PCIe tree and determine the actual minimum link speed of a
device which is a more general check than provided by
is_slot_appropriate. Thus, the kernel driver does not use or want the
is_slot_appropriate function call. Add a NO_IS_SLOT_APPROPRIATE_CHECK
definition which can be defined to remove the code.
If left undefined (the default) then the code will all be active and no
driver changes should be necessary.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Tested-by: Heng Ding <hengx.ding@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
Use memcpy instead of copying MAC address byte-by-byte.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Tested-by: Heng Ding <hengx.ding@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
Using the BIT macro can simplify the bit-shifting operation and make the
code look clean. Similar to how this is handled in the i40e base code,
define a macro for it in DPDK, so it can be used here too.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Tested-by: Heng Ding <hengx.ding@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
"else" is not generally useful after a break or return.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Tested-by: Heng Ding <hengx.ding@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
Recommended line length maximum is 80 characters
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Tested-by: Heng Ding <hengx.ding@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
Add comments which properly explain the undocumented use of bits in
TDLEN register prior to VF initializing it to the correct value. Note
that the mechanism is entirely software-defined and explain its purpose
to help reduce confusion in the future.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Tested-by: Heng Ding <hengx.ding@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
VF drivers must detect how many queues are available. Previously, the
driver assumed that each VF has at minimum 1 queue. This assumption is
incorrect, since it is possible that the PF has not yet assigned the
queues to the VF by the time the VF checks.
To resolve this, we added a check first to ensure that the first queue
is, in fact, owned by the VF at init_hw_vf time.
However, the code flow did not reset hw->mac.max_queues to 0.
In some cases, such as during reinit flows, we call init_hw_vf
without clearing the previous value of hw->mac.max_queues. Due to this,
when init_hw_vf errors out, if its error code is not properly handled
the VF driver may still believe it has queues which no longer belong to
it. Fix this by clearing the hw->mac.max_queues on exit due to errors.
Fixes: 8b8264bdb9 ("fm10k/base: check VF has a queue")
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Tested-by: Heng Ding <hengx.ding@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
Use bitshift instead of a divisor, because this is faster, and
eliminates any need for a '0' check. In our case, this even works
out because default Gen3 will be 0.
Because of this, we are also able to remove the check for non-zero value
in the VF code path since that will already be the default Gen3 case.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Tested-by: Heng Ding <hengx.ding@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
Make functions that are only referenced locally static.
Wrap fm10k_msg_data fm10k_iov_msg_data_pf[] in the new ifndef
NO_DEFAULT_SRIOV_MSG_HANDLERS so that drivers with custom SR-IOV
message handlers can strip it.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Tested-by: Heng Ding <hengx.ding@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
Since the resultant data type of the mac_update.mac_upper field is u16,
it does not make sense to typecast u8 variables to u32 first.
Fixes: 7223d200c2 ("fm10k: add base driver")
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Tested-by: Heng Ding <hengx.ding@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
Boulder Rapid is Intel new NIC within fm10k family.
This patch make DPDK driver support this new NIC.
Signed-off-by: Michael Qiu <michael.qiu@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
This patch enables fm10k TSO feature for both non-tunneling packet
and tunneling packet.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Acked-by: Michael Qiu <michael.qiu@intel.com>
This patch adds #pragma pack(push, 1) around some structures which are passed
via TLV messages. These structures must not be left unpacked as GCC and
other compilers are wont to do. Otherwise, we get invalid message
responses from the Switch Manager software since it sends 20 bytes and
we expect 24.
Solaris (and other OS's) are not C99 compliant, so they are not able
to use the C99 style #pragma pack() code. Wrap with C99 tag for easy
stripping.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
The SYSTIME_CFG.Adjust field has a Direction bit to indicate whether the
adjustment is positive or negative. However, we incorrectly read the
documentation and the direction bit should be set 1 when positive, not
when negative.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Add support for clock offset message from switch manager. Each PEP will
be responsible for notifying its own VFs, and the originating PEP must
notify its own VFs prior or in addition to sending, as it will not
receive a copy of its own message. Base drivers are expected to need
custom implementations so no message handler is provided in shared code.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Add support for tx timestamp mode response message. The switch manager
should send this message whenever the owner changes or when a new port
appears. To simplify logic, treat this as full clock ownership, and call
it the CLOCK_OWNER message. Implement this as a hw->flags field, so that
base driver may use it to disable any functions which modify the clock
including Tx timestamps, frequency adjustments, and offset adjustments.
This ensures only one PEP will be handling these at a time.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Remove support for VF transmit timestamps. VFs should not write the
timestamp bit in the Tx descriptor. Only one Tx timestamp can be
realistically handled at once. It is expected that the switch manager
use FFU logic to disable all timestamp requests except for those
originating from a specific virtual port. It is not possible to
correlate this timestamp accurately if more than one occurs out any
given EPL at a time. Since the primary purpose of Tx timestamps is to
implement PTP daemon, which also requires BAR4 access to change the
clock, do not allow VFs to transmit timestamp. Remove the PF<->VF
message for this behavior.
Note, the VF already didn't have ability to request Tx timestamp mode,
so it essentially wasn't allowed to timestamp before anyways under the
old API.
No longer support old API of request-response timestamp mode messages.
New API only sends timestamp-response when the switch decides which port
will be given control of timestamps. To simplify review of this code,
completely remove the support and re-add support for the response
message in a future patch.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
It is possible that the PF has not yet assigned resources to the VF.
Although rare, this could result in the VF attempting to read queues it
does not own and result in FUM or THI faults in the PF. To prevent this,
check queue 0 before we continue in init_hw_vf.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
When a VF issues an LPORT_STATE request to enable a port which is
already enabled, the PF will first disable the VF. Then it is supposed
to re-enable the VF again with new settings. This is primarily done in
order to ensure that the switch management software properly clears the
previous VF settings. (ie: switch flow rules and so forth). However,
there is a bug in the flow because we check if VF is enabled and don't
re-enable it at the end. The issue is that we disable the VF in order to
clear switch rules, and never follow-up with a re-enable. This results in
a call to enable the VF results in disabling the logical port.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
During initialization, the VF counts its rings by walking the TQDLOC
registers. This only works if the TQMAP/RQMAP registers are set to map
the out-of-bound rings to the first one, so the VF driver can detect when
it has run out of queues cleanly. Update the PF to reset the empty
TQMAP/RQMAP registers post-VFLR to prevent innocent VF drivers from
triggering malicious events.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
The VF will send a message to request multicast addresses with the
default vid. In the current code, if the PF has statically assigned a
VLAN to a VF, then the VF will not get the multicast addresses. Fix up
all of the various vlan messages to use identical checks (since each
check was different). Also use set as a variable, so that it simplifies
our check for whether vlan matches the pf_vid.
The new logic will allow set of a vlan if it is zero, automatically
converting to the default vid. Otherwise it will allow setting the PF
vid, or any VLAN if PF has not statically assigned a VLAN. This is
consistent behavior, and allows VF to request either 0 or the
default_vid without silently failing. Note that we need the check for
zero since VFs might not get the default VID message in time to actually
request non-zero VLANs.
Create a function, fm10k_iov_select_vid which implements the logic for
selecting a default vid. This helps us remove duplicate code and
streamlines location of this logic so that we don't make similar bugs in
the future.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
VFs were being improperly added to the switch's multicast group. The
error stems from the fact that incorrect arguments were passed to the
"update_mc_addr" function. It would seem to be a copy paste error since
the parameters are similar to the "update_uc_addr" function.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
A previous bug was uncovered by addition of a debug stat to indicate the
actual number of DWORDS we pulled from the mbmem. It turned out this was
not the same as the tx_dwords counter. While the previous bug fix should
have corrected this in all cases, add some debug stats that count the
number of DWORDs pushed or pulled from the mbmem. Base drivers can use
this in debug builds to help detect this problem in the future.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
When we connect to the mailbox, we insert a fake disconnect header so
that the code does not see an error and thus instantly error every time
we bring up the mailbox. However, we incorrectly record the tail and
head from the local perspective. Since the remote end shouldn't have
anything for us, add a "create_fake_disconnect_hdr" function which
inverts the TAIL and HEAD fields. This enables us to connect without any
errors of either TAIL or HEAD incorrectness, and prevents creating
extraneous error messages. This is necessary now since mbx_reset_work
does not actually clear the Tx FIFO head and tail pointers.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
