Add 'RTE_' prefix to defines:
- rename ETHER_ADDR_LEN as RTE_ETHER_ADDR_LEN.
- rename ETHER_TYPE_LEN as RTE_ETHER_TYPE_LEN.
- rename ETHER_CRC_LEN as RTE_ETHER_CRC_LEN.
- rename ETHER_HDR_LEN as RTE_ETHER_HDR_LEN.
- rename ETHER_MIN_LEN as RTE_ETHER_MIN_LEN.
- rename ETHER_MAX_LEN as RTE_ETHER_MAX_LEN.
- rename ETHER_MTU as RTE_ETHER_MTU.
- rename ETHER_MAX_VLAN_FRAME_LEN as RTE_ETHER_MAX_VLAN_FRAME_LEN.
- rename ETHER_MAX_VLAN_ID as RTE_ETHER_MAX_VLAN_ID.
- rename ETHER_MAX_JUMBO_FRAME_LEN as RTE_ETHER_MAX_JUMBO_FRAME_LEN.
- rename ETHER_MIN_MTU as RTE_ETHER_MIN_MTU.
- rename ETHER_LOCAL_ADMIN_ADDR as RTE_ETHER_LOCAL_ADMIN_ADDR.
- rename ETHER_GROUP_ADDR as RTE_ETHER_GROUP_ADDR.
- rename ETHER_TYPE_IPv4 as RTE_ETHER_TYPE_IPv4.
- rename ETHER_TYPE_IPv6 as RTE_ETHER_TYPE_IPv6.
- rename ETHER_TYPE_ARP as RTE_ETHER_TYPE_ARP.
- rename ETHER_TYPE_VLAN as RTE_ETHER_TYPE_VLAN.
- rename ETHER_TYPE_RARP as RTE_ETHER_TYPE_RARP.
- rename ETHER_TYPE_QINQ as RTE_ETHER_TYPE_QINQ.
- rename ETHER_TYPE_ETAG as RTE_ETHER_TYPE_ETAG.
- rename ETHER_TYPE_1588 as RTE_ETHER_TYPE_1588.
- rename ETHER_TYPE_SLOW as RTE_ETHER_TYPE_SLOW.
- rename ETHER_TYPE_TEB as RTE_ETHER_TYPE_TEB.
- rename ETHER_TYPE_LLDP as RTE_ETHER_TYPE_LLDP.
- rename ETHER_TYPE_MPLS as RTE_ETHER_TYPE_MPLS.
- rename ETHER_TYPE_MPLSM as RTE_ETHER_TYPE_MPLSM.
- rename ETHER_VXLAN_HLEN as RTE_ETHER_VXLAN_HLEN.
- rename ETHER_ADDR_FMT_SIZE as RTE_ETHER_ADDR_FMT_SIZE.
- rename VXLAN_GPE_TYPE_IPV4 as RTE_VXLAN_GPE_TYPE_IPV4.
- rename VXLAN_GPE_TYPE_IPV6 as RTE_VXLAN_GPE_TYPE_IPV6.
- rename VXLAN_GPE_TYPE_ETH as RTE_VXLAN_GPE_TYPE_ETH.
- rename VXLAN_GPE_TYPE_NSH as RTE_VXLAN_GPE_TYPE_NSH.
- rename VXLAN_GPE_TYPE_MPLS as RTE_VXLAN_GPE_TYPE_MPLS.
- rename VXLAN_GPE_TYPE_GBP as RTE_VXLAN_GPE_TYPE_GBP.
- rename VXLAN_GPE_TYPE_VBNG as RTE_VXLAN_GPE_TYPE_VBNG.
- rename ETHER_VXLAN_GPE_HLEN as RTE_ETHER_VXLAN_GPE_HLEN.
Do not update the command line library to avoid adding a dependency to
librte_net.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add 'rte_' prefix to structures:
- rename struct ether_addr as struct rte_ether_addr.
- rename struct ether_hdr as struct rte_ether_hdr.
- rename struct vlan_hdr as struct rte_vlan_hdr.
- rename struct vxlan_hdr as struct rte_vxlan_hdr.
- rename struct vxlan_gpe_hdr as struct rte_vxlan_gpe_hdr.
Do not update the command line library to avoid adding a dependency to
librte_net.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Replace the BSD license header with the SPDX tag for files
with only an Intel copyright on them.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Extend port_id definition from uint8_t to uint16_t in lib and drivers
data structures, specifically rte_eth_dev_data. Modify the APIs,
drivers and app using port_id at the same time.
Fix some checkpatch issues from the original code and remove some
unnecessary cast operations.
release_17_11 and deprecation docs have been updated in this patch.
Signed-off-by: Zhiyong Yang <zhiyong.yang@intel.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add basic management functions for the generic flow API (validate, create,
destroy, flush, query and list). Flow rule objects and properties are
arranged in lists associated with each port.
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Acked-by: Olga Shern <olgas@mellanox.com>
IEEE1588 forwarding mode uses same port to receive and transmit packets.
In this mode, the MAC address in the packets are not touched,
and therefore, packets could be sent with the same destination
MAC address as the MAC address of the port that is transmitting,
which causes the packet to be dropped in some NICs.
In order to avoid this scenario, MAC addresses are swapped
before packet is sent out.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Testpmd was only printing out second values when printing
RX/TX timestamp value, instead of both second and nanoseconds.
Since resolution of time counters is in nanoseconds,
testpmd should print out both.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Reviewed-by: John McNamara <john.mcnamara@intel.com>
In ieee1588fwd.c, timestamp.tv_sec is a time_t variable,
which is a long int, but it was being printed with PRIu64,
causing an issue on 32 bits.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Refactor the ieee1588_fwd mode in testpmd to use the new ethdev
APIs to enable and read IEEE1588 PTP timestamps.
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch simply applies the transform previously committed in
scripts/cocci/mtod-offset.cocci. No other modifications have been
made here.
Signed-off-by: Cyril Chemparathy <cchemparathy@ezchip.com>
Acked-by: Olivier Matz <olivier.matz@6wind.com>
The mbuf structure already contains a pointer to the beginning of the
buffer (m->buf_addr). It is not needed to use 8 bytes again to store
another pointer to the beginning of the data.
Using a 16 bits unsigned integer is enough as we know that a mbuf is
never longer than 64KB. We gain 6 bytes in the structure thanks to
this modification.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
* Updated to apply to latest on mainline.
* Disabled vector PMD in config as it relies heavily on the mbuf layout
This will be re-enabled in a subsequent commit once vPMD has been
reworked to take account of mbuf changes.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Olivier Matz <olivier.matz@6wind.com>
The rte_pktmbuf structure was initially included in the rte_mbuf
structure. This was needed when there was 2 types of mbuf (ctrl and
packet). As the control mbuf has been removed, we can merge the
rte_pktmbuf into the rte_mbuf structure.
Advantages of doing this:
- the access to mbuf fields is easier (ex: m->data instead of m->pkt.data)
- make the structure more consistent: for instance, there was no reason
to have the ol_flags field in rte_mbuf
- it will allow a deeper reorganization of the rte_mbuf structure in the
next commits, allowing to gain several bytes in it
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
[Bruce: updated for latest code and new example apps]
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
This commit removes trailing whitespace from lines in files. Almost all
files are affected, as the BSD license copyright header had trailing
whitespace on 4 lines in it [hence the number of files reporting 8 lines
changed in the diffstat].
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
[Thomas: remove spaces before tabs in libs]
[Thomas: remove more trailing spaces in non-C files]
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
