When compiling dpdk_qat app with an i686 target on a x86_64 OS,
an error message was shown, saying that it can only be built
on a 32-bit OS, which should be i686 OS, as other 32-bit OS
are not supported.
Fixes: 3460012bcc ("examples/qat: update")
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
As a example to use ptype info, l3fwd needs firstly to use
rte_eth_dev_get_supported_ptypes() API to check if device and/or
its PMD driver will parse and fill the needed packet type; if not,
use the newly added option, --parse-ptype, to analyze it in the
callback softly.
As the mode of EXACT_MATCH uses the 5 tuples to caculate hash, so
we narrow down its scope to:
a. ip packets with no extensions, and
b. L4 payload should be either tcp or udp.
Note: this patch does not completely solve the issue, "cannot run
l3fwd on virtio or other devices", because hw_ip_checksum may be
not supported by the devices. Currently we can:
a. remove this requirements, or
b. wait for virtio front end (pmd) to support it.
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Added validation for queue id of config parameter tuple.
This validation enforces user to enter queue ids of a port
from 0 and in sequence.
This additional validation on queue ids avoids ixgbe crash caused
by null rxq pointer access inside ixgbe_dev_rx_init.
Reason for null rxq is, L3fwd application allocates memory only for
queues passed by user. But rte_eth_dev_start tries to initialize rx
queues in sequence from 0 to nb_rx_queues,
which is not true and coredump while accessing the unallocated queue .
Fixes: af75078fec ("first public release")
Signed-off-by: Reshma Pattan <reshma.pattan@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
While the last arg of virtio_tx_route() asks a vlan tag, we currently
feed it with device_fh, which is wrong. Fix it.
Fixes: 4796ad63ba ("examples/vhost: import userspace vhost application")
Reported-by: Qian Xu <qian.q.xu@intel.com>
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Comments for PKT_TX_TCP_SEG at rte_mbuf says that we should only set
PKT_TX_IP_CKSUM and reset ip hdr checksum for IPv4:
- if it's IPv4, set the PKT_TX_IP_CKSUM flag and write the IP checksum
to 0 in the packet
Fixes: 9fd72e3cbd ("examples/vhost: add virtio offload")
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
For checksum offloading only case, the TCP/IP stack would
have calculated the pseudo checksum. Therefore, we don't
need to re-calculate it again here; remove it.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
NULL crypto operation is now supported, but l2fwd-crypto
was missing an update on the list of supported algorithms
that can be passed from command line.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
AES GCM is an algorithm for both ciphering and authentication,
but the authentication algorithm was missing in the
list of supported algorithms that can be passed from command line.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Since SNOW3G UEA2/UIA2 are supported now by both HW and SW,
l2fwd-crypto may use them, extending the list of algorithms
parsed from command line.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Previous cdev parameter was changed to cdev_type,
to select a crypto device type preference (HW/SW/ANY),
instead of the device itself (QAT/AESNI...).
Also deleted cdev duplicated parameter from the help.
Fixes: 27cf2d1b18 ("examples/l2fwd-crypto: discover capabilities")
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Fiona Trahe <fiona.trahe@intel.com>
For GLIBC < 2.17 it is necessery to add -lrt for linker
from glibc > 2.17 The `clock_*' suite of functions (declared in <time.h>) is now
available directly in the main C library. This affect Ubuntu 12.04 in i686
and other older Linux Distros).
Fixes: 4758404a30 ("mk: fix eal shared library dependencies")
Signed-off-by: Daniel Mrzyglod <danielx.t.mrzyglod@intel.com>
The flag ENABLE_MULTI_BUFFER_OPTIMIZE has been removed so the
related comments are now useless.
Fixes: 268888b5b0 ("examples/l3fwd: modularize")
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
clang reports these errors:
error: too many arguments to function call, expected 2, have 3
examples/performance-thread/l3fwd-thread/main.c:1220:1: note:
'l3fwd_simple_forward' declared here
examples/l3fwd/main.c:550:1: error: unused function 'send_packetsx4'
The function is used only when ENABLE_MULTI_BUFFER_OPTIMIZE is 1.
Fixes: d48415e1fe ("examples/performance-thread: add l3fwd-thread app")
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
This patch implements PQoS as a sample application.
PQoS allows management of the CPUs last level cache,
which can be useful for DPDK to ensure quality of service.
The sample app links against the existing 01.org PQoS library
(https://github.com/01org/intel-cmt-cat).
White paper demonstrating example use case "Increasing Platform Determinism
with Platform Quality of Service for the Data Plane Development Kit"
(http://www.intel.com/content/www/us/en/communications/increasing-platform-determinism-pqos-dpdk-white-paper.html)
Signed-off-by: Wojciech Andralojc <wojciechx.andralojc@intel.com>
Signed-off-by: Tomasz Kantecki <tomasz.kantecki@intel.com>
Signed-off-by: Marcel D Cornu <marcel.d.cornu@intel.com>
It seems that for the most use cases, previous hash_multi_lookup provides
better performance, and more, sequential lookup can cause significant
performance drop.
This patch sets previously optional hash_multi_lookup method as default.
It also provides some minor optimizations such as queue drain only on used
tx ports.
Fixes: 94c54b4158 ("examples/l3fwd: rework exact-match")
Fixes: dc81ebbaca ("lpm: extend IPv4 next hop field")
Fixes: 64d3955de1 ("examples/l3fwd: fix ARM build")
Reported-by: Qian Xu <qian.q.xu@intel.com>
Signed-off-by: Tomasz Kulasek <tomaszx.kulasek@intel.com>
l3fwd does not compile with HASH_MULTI_LOOKUP.
2 issues:
* in 64d395 mask0 changed type from xmm_t to rte_xmm_t
-> use x field from rte_xmm_t
* in dc81eb dst_port parameter changed to uint32_t
-> change uint16_t dst_port to uin32_t dsp_port
Fixes: dc81ebbaca ("lpm: extend IPv4 next hop field")
Fixes: 64d3955de1 ("examples/l3fwd: fix ARM build")
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Updated ip_pipeline app is using new changes from LPM library
(Increased number of next hops and added new config structure
for LPM IPv4).
Fixes: f1f7261838 ("lpm: add a new config structure for IPv4")
Signed-off-by: Michal Kobylinski <michalx.kobylinski@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Previous l3fwd-power only processes IP and IPv6 packets, other
packets' mbufs are not freed, and this causes a memory leak.
This patch fixes this issue.
Fixes: 3c0184cc0c ("examples: replace some offload flags with packet type")
Signed-off-by: Shaopeng He <shaopeng.he@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
Acked-by: Michael Qiu <michael.qiu@intel.com>
Currently, the example vmdq_dcb only works on Intel(R) 82599 NICs.
This patch extends this sample to make it work both on Intel(R) 82599
and X710/XL710 NICs by making the following changes:
1. add VMDQ base queue checking to avoid forwarding on PF queues.
2. assign each VMDQ pool to a MAC address.
3. add more arguments (nb-tcs, enable-rss) to change the default
setting
4. extend the max number of queues from 128 to 1024.
This patch also reworks the user guide for the vmdq_dcb sample.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tell the compiler to use unsigned constants for left shift ops,
otherwise building with gcc >= 6.0 fails due to multiple warnings like:
warning: left shift of negative value [-Wshift-negative-value]
Signed-off-by: Panu Matilainen <pmatilai@redhat.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
The pass-through pipeline implementation is extended with load balancing
function. This function allows uniform distribution of the packets among
its output ports. For packets distribution, any application level logic
can be applied. For instance, in this implementation, hash value
computed over specific header fields of the incoming packets has been
used to spread traffic uniformly among the output ports.
The following pass-through configuration can be used for implementing
load balancing function over ipv4 traffic;
[PIPELINE0]
type = PASS-THROUGH
core = 0
pktq_in = RXQ0.0 RXQ1.0 RXQ2.0 RXQ3.0
pktq_out = TXQ0.0 TXQ1.0 TXQ2.0 TXQ3.0
dma_src_offset = 278; mbuf (128) + headroom (128) + 1st ethertype offset (14) + ttl offset within ip header = 278 (ipv4)
dma_dst_offset = 128; mbuf (128)
dma_size = 16
dma_src_mask = 00FF0000FFFFFFFFFFFFFFFFFFFFFFFF
dma_hash_offset = 144; (dma_dst_offset+dma_size)
lb = hash
Signed-off-by: Jasvinder Singh <jasvinder.singh@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
This patch add packet dumping feature to ip_pipeline. Output port type
SINK now supports dumping packets to PCAP file before releasing mbuf back
to mempool. This feature can be applied by specifying parameters in
configuration file as shown below:
[PIPELINE1]
type = PASS-THROUGH
core = 1
pktq_in = SOURCE0 SOURCE1
pktq_out = SINK0 SINK1
pcap_file_wr = /path/to/eth1.pcap /path/to/eth2.pcap
pcap_n_pkt_wr = 80 0
The configuration section "pcap_file_wr" contains full path and name of
the PCAP file which the packets will be dumped to. If multiple SINKs
exists, each shall have its own PCAP file path listed in this section,
separated by spaces. Multiple SINK ports shall NOT share same PCAP file to
be dumped.
The configuration section "pcap_n_pkt_wr" contains integer value(s)
and indicates the maximum number of packets to be dumped to the PCAP file.
If this value is "0", the "infinite" dumping mode will be used. If this
value is N (N > 0), the dumping will be finished when the number of
packets dumped to the file reaches N.
To enable PCAP dumping support to IP pipeline, the compiler option
CONFIG_RTE_PORT_PCAP must be set to 'y'. It is possible to disable this
feature by removing "pcap_file_wr" and "pcap_n_pkt_wr" lines from the
configuration file.
Signed-off-by: Fan Zhang <roy.fan.zhang@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
This patch add PCAP file support to ip_pipeline. Input port type SOURCE
now supports loading specific PCAP file and sends the packets in it to
pipeline instance. The packets are then released by SINK output port. This
feature can be applied by specifying parameters in configuration file as
shown below;
[PIPELINE1]
type = PASS-THROUGH
core = 1
pktq_in = SOURCE0 SOURCE1
pktq_out = SINK0 SINK1
pcap_file_rd = /path/to/eth1.PCAP /path/to/eth2.PCAP
pcap_bytes_rd_per_pkt = 0 64
The configuration section "pcap_file_rd" contains full path and name of
the PCAP file to be loaded. If multiple SOURCEs exists, each shall have
its own PCAP file path listed in this section, separated by spaces.
Multiple SOURCE ports may share same PCAP file to be copied.
The configuration section "pcap_bytes_rd_per_pkt" contains integer value
and indicates the maximum number of bytes to be copied from each packet
in the PCAP file. If this value is "0", all packets in the file will be
copied fully; if the packet size is smaller than the assigned value, the
entire packet is copied. Same as "pcap_file_rd", every SOURCE shall have
its own maximum copy byte number.
To enable PCAP support to IP pipeline, the compiler option
CONFIG_RTE_PORT_PCAP must be set to 'y'. It is possible to disable PCAP
support by removing "pcap_file_rd" and "pcap_bytes_rd_per_pkt" lines
from the configuration file.
Signed-off-by: Fan Zhang <roy.fan.zhang@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Change the fields of outer_mac and inner_mac in struct
rte_eth_tunnel_filter_conf from pointer to struct in order to
keep the code's readability.
Signed-off-by: Xutao Sun <xutao.sun@intel.com>
Signed-off-by: Jijiang Liu <jijiang.liu@intel.com>
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
The names of function for tunnel port configuration are not
accurate. They're tunnel_add/del, better change them to
tunnel_port_add/del.
The old functions are directly replaced because the API and ABI
compatibility of ethdev are already broken in 16.04.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The internal buffering of packets for TX in sample apps is no longer
needed, so this patchset also replaces this code with calls to the new
rte_eth_tx_buffer* APIs in:
* l2fwd-jobstats
* l2fwd-keepalive
* l2fwd
* l3fwd-acl
* l3fwd-power
* link_status_interrupt
* client_server_mp
* l2fwd_fork
* packet_ordering
* qos_meter
Signed-off-by: Tomasz Kulasek <tomaszx.kulasek@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Building examples fails with CONFIG_RTE_LIBRTE_LPM=n
The error is caused by the new app ipsec-secgw that gets build
without checking for configuration dependencies.
Fixes: d299106e8e ("examples/ipsec-secgw: add IPsec sample application")
The patch also reorders a couple entries to maintain alphabetic order.
Reported-by: Jan Viktorin <viktorin@rehivetech.com>
Signed-off-by: Sergio Gonzalez Monroy <sergio.gonzalez.monroy@intel.com>
Enable NEON support in exact match mode.
l3fwd example did not compile on ARM due to SSE2 instrincics used
in generic part.
Some instrinsins were used to initialize data structures and those were
replaced by ordinary structure initalization.
All SSE2 intrinsics used in forwarding, i.e. masking the IP/TCP header
are moved to single inline function and made arch-specific.
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Crypto devices now have information about
which crypto operations they are capable of provide.
This patch makes the app use this information,
removing all hardcoded values.
User now needs to create the virtual crypto devices
or bind the HW crypto devices, and the app will use
the ones capable of performing the crypto op specified
(user can select between HW/SW through command line)
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Tested-by: Min Cao <min.cao@intel.com>
Acked-by: Sergio Gonzalez Monroy <sergio.gonzalez.monroy@intel.com>
Added cipher-only, hash-only operation cases,
which will be supported in the future.
Also, only sets authentication and ciphering parameters
when needed.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Tested-by: Min Cao <min.cao@intel.com>
Acked-by: Sergio Gonzalez Monroy <sergio.gonzalez.monroy@intel.com>
So far, L2fwd crypto app could parse cipher, auth keys
and IV, but not AAD (additional authentication data).
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Tested-by: Min Cao <min.cao@intel.com>
Acked-by: Sergio Gonzalez Monroy <sergio.gonzalez.monroy@intel.com>
Implement key parsing functionality, so user can provide
auth and cipher keys, plus IV, from the command line.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Tested-by: Min Cao <min.cao@intel.com>
Acked-by: Sergio Gonzalez Monroy <sergio.gonzalez.monroy@intel.com>
Sample app implementing an IPsec Security Geteway.
The main goal of this app is to show the use of cryptodev framework
in a "real world" application.
Currently only supported static IPv4 ESP IPsec tunnels for the following
algorithms:
- Cipher: AES-CBC, NULL
- Authentication: HMAC-SHA1, NULL
Not supported:
- SA auto negotiation (No IKE implementation)
- chained mbufs
Signed-off-by: Sergio Gonzalez Monroy <sergio.gonzalez.monroy@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
As cryptodev library does not depend on mbuf_offload library
any longer, this patch removes it.
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Deepak Kumar Jain <deepak.k.jain@intel.com>
This patch modifies the crypto burst enqueue/dequeue APIs to operate on bursts
rte_crypto_op's rather than the current implementation which operates on
rte_mbuf bursts, this simplifies the burst processing in the crypto PMDs and the
use of crypto operations in general, including new functions for managing
rte_crypto_op pools.
These changes continues the separation of the symmetric operation parameters
from the more general operation parameters, which will simplify the integration
of asymmetric crypto operations in the future.
PMDs, unit tests and sample applications are also modified to work with the
modified and new API.
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Deepak Kumar Jain <deepak.k.jain@intel.com>
Remove unused phys_addr field from key in crypto_xform,
simplify struct and fix knock-on impacts in l2fwd-crypto app
Signed-off-by: Fiona Trahe <fiona.trahe@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Deepak Kumar Jain <deepak.k.jain@intel.com>
This patch splits symmetric specific definitions and
functions away from the common crypto APIs to facilitate the future extension
and expansion of the cryptodev framework, in order to allow asymmetric
crypto operations to be introduced at a later date, as well as to clean the
logical structure of the public includes. The patch also introduces the _sym
prefix to symmetric specific structure and functions to improve clarity in
the API.
Signed-off-by: Fiona Trahe <fiona.trahe@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Deepak Kumar Jain <deepak.k.jain@intel.com>
Two new pipeline API functions have been added to the library. The packet
hijack API function can be called by any input/output port or table action
handler to remove selected packets from the burst of packets read from one
of the pipeline input ports and then either send these packets out through
any pipeline output port or drop them.
Another packet drop API function can be used by the pipeline action
handlers (port in/out, table) to drop the packets selected using packet
mask. This function updates the drop statistics counters correctly.
Signed-off-by: Jasvinder Singh <jasvinder.singh@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Currently, there is no mechanism that allows the pipeline ports (in/out)
and table action handlers to override the default forwarding decision
(as previously configured per input port or in the table entry). The port
(in/out) and table action handler prototypes have been changed to allow
pipeline action handlers (port in/out, table) to remove the selected
packets from the further pipeline processing and to take full ownership
for these packets. This feature will be helpful to implement functions
such as exception handling (e.g. TTL =0), load balancing etc.
Signed-off-by: Jasvinder Singh <jasvinder.singh@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
A new rte_lpm_config structure is used so LPM library will allocate
exactly the amount of memory which is necessary to hold application’s
rules.
Signed-off-by: Michal Kobylinski <michalx.kobylinski@intel.com>
Acked-by: David Hunt <david.hunt@intel.com>
This patch extend next_hop field from 8-bits to 24-bits in LPM library
for IPv4.
Added versioning symbols to functions and updated
library and applications that have a dependency on LPM library.
Signed-off-by: Michal Kobylinski <michalx.kobylinski@intel.com>
Acked-by: David Hunt <david.hunt@intel.com>
This patch adds link identification feature to packet framework. To
identify a link, user can use both existing port-mask option, or specify
PCI device in every LINK section in the configuration file.
Signed-off-by: Fan Zhang <roy.fan.zhang@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
This patch adds CPU utilization measurement and idle cycle rate
computation to packet framework. The measurement is done by measuring
the cycles spent while a thread pulls zero packet from RX queue. These
cycles are treated as idle cycles (or headroom). A CLI command is added
to display idle cycle rate of specific thread. The CLI command format is
shown as following:
t <thread_id> headroom
Signed-off-by: Fan Zhang <roy.fan.zhang@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Current implementation of Exact-Match uses different execution path than
for LPM. Unifying them allows to reuse big part of LPM code and sightly
increase performance of Exact-Match.
Main changes:
-------------
* Packet classification stage is separated from the rest of path for both
LPM and EM.
* Packet processing, modifying and transmit part is the same for LPM and EM
and mostly based on the current LPM implementation.
* Shared code is moved to the common file "l3fwd_sse.h".
* While sequential packet classification in EM path, seems to be faster
than using multi hash lookup, used before, it is used by default. Old
implementation is moved to the file l3fwd_em_hlm_sse.h and can be enabled
with HASH_LOOKUP_MULTI global define in compilation time.
Signed-off-by: Tomasz Kulasek <tomaszx.kulasek@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
This patch adds new function rte_jobstats_abort.
It marks *job* as finished and time of this work will be add to management
time instead of execution time.
This function should be used instead of rte_jobstats_finish if condition
occurs, condition is defined by the application for example when receiving
n>0 packets.
Example of usage is added to the example l2fwd-jobstats.
At maximum load do-while loop inside Idle job will be execute once because
one or more jobs waiting to be executed, so this time should not be include
as the execution time by calling rte_jobstats_abort().
Signed-off-by: Marcin Kerlin <marcinx.kerlin@intel.com>
Acked-by: Fan Zhang <roy.fan.zhang@intel.com>
