This patch enables configuring MTU for i40e.
Since changing MTU needs to reconfigure queue, the port must be
stopped before configuring MTU.
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Previously, there was a known issue "On Intel® 40G Ethernet
Controller stopping the port does not really down the port link."
There were two reasons why the port was always kept up.
1. Old firmware versions had issues when "Set PHY config command"
was used on 40G NICs.
2. The kernel i40e driver didn't call "Set PHY config command" when
ifconfig up/down was used, it assumes the link is always up. But
in DPDK, ports are forced down when an applications quits. So if
the port is then switched to being controlled by kernel the driver,
the port can not be brought up through "ifconfig <ethx> up".
This patch fixes this issue by adding in "Set PHY config command"
into our driver. This is now possible because with newer firmware
there is no longer a problem using this command.
With this fix, after DPDK quit, if the port is switched to being used
by the kernel driver, "ethtool -s <ethx> autoneg on" can be used to
turn on the auto negotiation, and then port can be brought up through
"ifconfig <ethx> up".
NOTE: requires kernel i40e driver version >= 1.4.X
Fixes: 2f1e228174 ("i40e: skip link control as firmware workaround")
Fixes: 16c979f9ad ("i40e: disable setting of PHY configuration")
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Use ARM NEON intrinsic to implement ixgbe vPMD
Signed-off-by: Jianbo Liu <jianbo.liu@linaro.org>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
[style fixes as highlighted by checkpatch.pl]
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
This patch introduced scalable multi-writer Cuckoo Hash insertion
based on a split Cuckoo Search and Move operation using Intel
TSX. It can do scalable hash insertion with 22 cores with little
performance loss and negligible TSX abortion rate.
* Added an extra rte_hash flag definition to switch default single writer
Cuckoo Hash behavior to multiwriter.
- If HTM is available, it would use hardware feature for concurrency.
- If HTM is not available, it would fall back to spinlock.
* Created a rte_cuckoo_hash_x86.h file to hold all x86-arch related
cuckoo_hash functions. And rte_cuckoo_hash.c uses compile time flag to
select x86 file or other platform-specific implementations. While HTM check
is still done at runtime (same idea with
RTE_HASH_EXTRA_FLAGS_TRANS_MEM_SUPPORT)
* Moved rte_hash private struct definitions to rte_cuckoo_hash.h, to allow
rte_cuckoo_hash_x86.h or future platform dependent functions to include.
* Following new functions are created for consistent names when new platform
TM support are added.
- rte_hash_cuckoo_move_insert_mw_tm: do insertion with bucket movement.
- rte_hash_cuckoo_insert_mw_tm: do insertion without bucket movement.
* One extra multi-writer test case is added.
Signed-off-by: Wei Shen <wei1.shen@intel.com>
Signed-off-by: Sameh Gobriel <sameh.gobriel@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Until now, the objects stored in a mempool were internally stored in a
ring. This patch introduces the possibility to register external handlers
replacing the ring.
The default behavior remains unchanged, but calling the new function
rte_mempool_set_ops_byname() right after rte_mempool_create_empty() allows
the user to change the handler that will be used when populating
the mempool.
This patch also adds a set of default ops (function callbacks) based
on rte_ring.
Signed-off-by: David Hunt <david.hunt@intel.com>
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Acked-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: Olivier Matz <olivier.matz@6wind.com>
NSH packet can be recognized by Intel X710/XL710 series.
This patch enables the new packet type.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Yulong Pei <yulong.pei@intel.com>
Acked-by: Zhe Tao <zhe.tao@intel.com>
- added VXLAN, GENEVE and NVGRE tunnel flow types
- added PORT flow type for accounting physical/virtual
port or channel number in flow creation
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Add a new virtual device named virtio-user, which can be used just like
eth_ring, eth_null, etc. To reuse the code of original virtio, we do
some adjustment in virtio_ethdev.c, such as remove key _static_ of
eth_virtio_dev_init() so that it can be reused in virtual device; and
we add some check to make sure it will not crash.
Configured parameters include:
- queues (optional, 1 by default), number of queue pairs, multi-queue
not supported for now.
- cq (optional, 0 by default), not supported for now.
- mac (optional), random value will be given if not specified.
- queue_size (optional, 256 by default), size of virtqueues.
- path (madatory), path of vhost user.
When enable CONFIG_RTE_VIRTIO_USER (enabled by default), the compiled
library can be used in both VM and container environment.
Examples:
path_vhost=<path_to_vhost_user> # use vhost-user as a backend
sudo ./examples/l2fwd/build/l2fwd -c 0x100000 -n 4 \
--socket-mem 0,1024 --no-pci --file-prefix=l2fwd \
--vdev=virtio-user0,mac=00:01:02:03:04:05,path=$path_vhost -- -p 0x1
Known issues:
- Control queue and multi-queue are not supported yet.
- Cannot work with --huge-unlink.
- Cannot work with no-huge.
- Cannot work when there are more than VHOST_MEMORY_MAX_NREGIONS(8)
hugepages.
- Root privilege is a must (mainly becase of sorting hugepages according
to physical address).
- Applications should not use file name like HUGEFILE_FMT ("%smap_%d").
- Cannot work with vhost-net backend.
Signed-off-by: Huawei Xie <huawei.xie@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
All other DPDK PMDs doesn't support concurrent receiving or sending
packets to the same queue. The upper application should deal with
this, normally through queue and core bindings.
Due to historical reason, vhost internally supports concurrent lockless
enqueuing packets to the same virtio queue through costly cmpset operation.
This patch removes this internal lockless implementation and should improve
performance a bit.
Luckily DPDK OVS doesn't rely on this behavior.
Signed-off-by: Huawei Xie <huawei.xie@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Allow reconnecting on failure by default when:
- DPDK app starts first and QEMU (as the server) is not started yet.
Without reconnecting, DPDK app would simply fail on vhost-user
registration.
- QEMU restarts, say due to OS reboot.
Without reconnecting, you can't re-establish the connection without
restarting DPDK app.
This patch make it work well for both above cases. It simply creates
a new thread, and keep trying calling "connect()", until it succeeds.
The reconnect could be disabled when RTE_VHOST_USER_NO_RECONNECT flag
is set.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Add a new paramter (flags) to rte_vhost_driver_register(). DPDK
vhost-user acts as client mode when RTE_VHOST_USER_CLIENT flag
is set. The flags would also allow future extensions without
breaking the API (again).
The rest is straingfoward then: allocate a unix socket, and
bind/listen for server, connect for client.
This extension is for vhost-user only, therefore we simply quit
and report error when any flags are given for vhost-cuse.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
With all the previous prepare works, we are just one step away from
the final ABI refactoring. That is, to change current API to let them
stick to vid instead of the old virtio_net dev.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Tested-by: Rich Lane <rich.lane@bigswitch.com>
Acked-by: Rich Lane <rich.lane@bigswitch.com>
The new API rte_vhost_avail_entries() is actually a rename of
rte_vring_available_entries(), with the "vring" to "vhost" name
change to keep the consistency of other vhost exported APIs.
This change could let us avoid the dependency of "virtio_net"
struct, to prepare for the ABI refactoring.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Tested-by: Rich Lane <rich.lane@bigswitch.com>
Acked-by: Rich Lane <rich.lane@bigswitch.com>
1. add KNI support to the IP Pipeline sample Application
2. some bug fix
3. update doc
4. add config file with two KNI interfaces connected using
a Linux kernel bridge
Signed-off-by: WeiJie Zhuang <zhuangwj@gmail.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Underlying libsso_snow3g library now supports bit-level
operations, so PMD has been updated to allow them.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Deepak Kumar Jain <deepak.k.jain@intel.com>
With the library update, the way to compile the library
has changed, so documentation reflects this change.
Also, the patch to fix the compilation issues present with gcc > 5.0
has been removed, as the issues have been fixed in the library.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Deepak Kumar Jain <deepak.k.jain@intel.com>
The underlying libsso library that SNOW3G PMD uses has been updated,
so now it is called libsso_snow3g. Also, the path to the library
has been renamed to reflect this changes (now called LIBSSO_SNOW3G_PATH).
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Deepak Kumar Jain <deepak.k.jain@intel.com>
Added new SW PMD which makes use of the libsso_kasumi SW library,
which provides wireless algorithms KASUMI F8 and F9
in software.
This PMD supports cipher-only, hash-only and chained operations
("cipher then hash" and "hash then cipher") of the following
algorithms:
- RTE_CRYPTO_SYM_CIPHER_KASUMI_F8
- RTE_CRYPTO_SYM_AUTH_KASUMI_F9
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Deepak Kumar Jain <deepak.k.jain@intel.com>
Some crypto PMDs that support symmetric crypto were not marked
as supported in the supported feature flags table.
Fixes: 2373c0661b ("doc: add cryptodevs guide overview")
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Deepak Kumar Jain <deepak.k.jain@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
The new pdump tool is added for packet capturing on dpdk.
This tool runs as secondary process by default.
Tool facilitates the command line options like
port, device_id, queue which user should pass on
to the tool to request the packet capture on those devices.
Tool creates the rte ring, mempool and pcap vdev and
calls the enable API of the pdump library with port/device_id,
queue, ring and mempool as arguments to enable the packet
capture on specific devices and gets the packets from the
primary process over the ring. Once the packets are
received, those packets will be send to the pcap vdev.
Tool can be terminated by using ctrl+c(SIGINT) upon which tool
calls the disable API of the pdump library to disable the packet capture
and dequeues the rest of the packets from the ring and sends them on
to the pcap vdev, then after releases all allocated resources.
Signed-off-by: Reshma Pattan <reshma.pattan@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The librte_pdump library provides a framework for
packet capturing in dpdk. The library provides set of
APIs to initialize the packet capture framework, to
enable or disable the packet capture, and to uninitialize
it.
The librte_pdump library works on a client/server model.
The server is responsible for enabling or disabling the
packet capture and the clients are responsible
for requesting the enabling or disabling of the packet
capture.
Enabling APIs are supported with port, queue, ring and
mempool parameters. Applications should pass on this information
to get the packets from the dpdk ports.
For enabling requests from applications, library creates the client
request containing the mempool, ring, port and queue information and
sends the request to the server. After receiving the request, server
registers the Rx and Tx callbacks for all the port and queues.
After the callbacks registration, registered callbacks will get the
Rx and Tx packets. Packets then will be copied to the new mbufs that
are allocated from the user passed mempool. These new mbufs then will
be enqueued to the application passed ring. Applications need to dequeue
the mbufs from the rings and direct them to the devices like
pcap vdev for viewing the packets outside of the dpdk
using the packet capture tools.
For disabling requests, library creates the client request containing
the port and queue information and sends the request to the server.
After receiving the request, server removes the Rx and Tx callback
for all the port and queues.
Signed-off-by: Reshma Pattan <reshma.pattan@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The new fields nb_rx_queues and nb_tx_queues are added to the
rte_eth_dev_info structure.
Changes to API rte_eth_dev_info_get() are done to update these new fields
to the rte_eth_dev_info object.
Release notes is updated with the changes.
The librte_pdump library needs to register Rx and Tx callbacks for all
the nb_rx_queues and nb_tx_queues, when application wants to capture the
packets on all the software configured number of Rx and Tx queues of the
device. So far there is no support to get nb_rx_queues and nb_tx_queues
information from the ethdev library. Hence these changes are introduced.
Signed-off-by: Reshma Pattan <reshma.pattan@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Adds and documents new callbacks that allow transitions to core
states other than dead to be reported to applications.
Signed-off-by: Remy Horton <remy.horton@intel.com>
The current extended ethernet statistics fetching involve doing several
string operations, which causes performance issues if there are lots of
statistics and/or network interfaces. This patch changes the test-pmd
and proc_info applications to use the new xstats API, and removes
deprecated code associated with the old API.
Signed-off-by: Remy Horton <remy.horton@intel.com>
The current extended ethernet statistics fetching involve doing several
string operations, which causes performance issues if there are lots of
statistics and/or network interfaces. This patch changes the xstats
functions to instead use a numeric identifier rather than a string, and
adds the ability to retrieve identifier-to-string mappings.
Signed-off-by: Remy Horton <remy.horton@intel.com>
This patch enables configurable tx_first burst number.
Use "start tx_first (burst_num)" to specify how many bursts of packets to
be sent before forwarding start, or "start tx_first" like before for the
default 1 burst send.
Signed-off-by: Zhihong Wang <zhihong.wang@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
This patch adds retry option in testpmd to prevent most packet losses.
It can be enabled by "set fwd <mode> retry". All modes except rxonly
support this option.
Adding retry mechanism expands test case coverage to support scenarios
where packet loss affects test results.
Signed-off-by: Zhihong Wang <zhihong.wang@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
The behavior of PKT_RX_VLAN_PKT was not very well defined, resulting in
PMDs not advertising the same flags in similar conditions.
Following discussion in [1], introduce 2 new flags PKT_RX_VLAN_STRIPPED
and PKT_RX_QINQ_STRIPPED that are better defined:
PKT_RX_VLAN_STRIPPED: a vlan has been stripped by the hardware and its
tci is saved in mbuf->vlan_tci. This can only happen if vlan stripping
is enabled in the RX configuration of the PMD.
For now, the old flag PKT_RX_VLAN_PKT is kept but marked as deprecated.
It should be removed from applications and PMDs in a future revision.
This patch also updates the drivers. For PKT_RX_VLAN_PKT:
- e1000, enic, i40e, mlx5, nfp, vmxnet3: done, PKT_RX_VLAN_PKT already
had the same meaning than PKT_RX_VLAN_STRIPPED, minor update is
required.
- fm10k: done, PKT_RX_VLAN_PKT already had the same meaning than
PKT_RX_VLAN_STRIPPED, and vlan stripping is always enabled on fm10k.
- ixgbe: modification done (vector and normal), the old flag was set
when a vlan was recognized, even if vlan stripping was disabled.
- the other drivers do not support vlan stripping.
For PKT_RX_QINQ_PKT, it was only supported on i40e, and the behavior was
already correct, so we can reuse the same bit value for
PKT_RX_QINQ_STRIPPED.
[1] http://dpdk.org/ml/archives/dev/2016-April/037837.html,
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
This patch docs the issue on EAL argument that the last EAL
argument is replaced by program name in argv[].
Reported-by: Ziye Yang <ziye.yang@intel.com>
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
This patch is used to add the class_id (class_code,
subclass_code, programming_interface) support for
pci_device probe. With this patch, it will be
flexible for users to probe a class of devices
by class_id.
Signed-off-by: Ziye Yang <ziye.yang@intel.com>
The commit 66819e6 has introduced a dependency on libarchive to be able
to use some tar resources in the unit tests.
It is now an optional dependency because some systems do not have it
installed.
If CONFIG_RTE_APP_TEST_RESOURCE_TAR is disabled, the PCI test will not
be run. When a "configure" script will be integrated, the libarchive
availability could be checked to automatically enable the option.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Reviewed-by: Jan Viktorin <viktorin@rehivetech.com>
The log history uses rte_mempool. In order to remove the mempool
dependency in EAL (and improve the build), this feature is deprecated.
The ABI is kept but the behaviour is now voided because it seems this
function was not used. The history can be read from syslog.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: David Marchand <david.marchand@6wind.com>
Fix broken console directive in the ABI validator section of the
ABI versioning docs.
Fixes: f1ef9794f9 ("doc: add ABI guidelines")
Signed-off-by: John McNamara <john.mcnamara@intel.com>
A previous patch modified the CLIs witout updating the examples.
Fixes: 53b2bb9b7e ("app/testpmd: new flow director commands")
Signed-off-by: Mauricio Vasquez B <mauricio.vasquezbernal@studenti.polito.it>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Port needs to be stopped and then closed before it can be detached,
but the documentation was only saying to close the port.
Also, both sections for port detaching and attaching has been reformatted
slightly, to show clearly how to use the commands.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
"port config all txqflags <value>" allows for
specifying txq_flags value in command line.
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
"port config all scatter on|off" allows for
controlling rxmode.enable_scatter in command line.
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
This parameter allows for controlling rxmode.enable_scatter
which in turn allow for multi-segment packet receive tests.
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
The routing pipeline registers a callback function with the nic ports and
this function is invoked for updating the routing entries (corresponding to
local host and directly attached network) tables whenever the nic ports
change their states (up/down).
Signed-off-by: Jasvinder Singh <jasvinder.singh@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
As a result of tracking, output ports of routing pipelines are linked with
physical nic ports (potentially through other pipeline instances).
Thus, the mac addresses of the NIC ports are assigned to routing pipeline
out ports which are connected to them and are further used in routing table
entries instead of hardcoded default values.
Signed-off-by: Jasvinder Singh <jasvinder.singh@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
This patch enables rss (receive side scaling) per network interface
through the configuration file. The user can specify following
parameters in LINK section for enabling the rss feature - rss_qs,
rss_proto_ipv4, rss_proto_ipv6 and ip_proto_l2.
The "rss_qs" is mandatory parameter which indicates the queues to be
used for rss, while rest of the parameters are optional. When optional
parameters are not provided in the configuration file, default setting
(ETH_RSS_IPV4 | ETH_RSS_IPV6) is assumed for "rss_hf" field of the
rss_conf structure.
For example, following configuration can be applied for using the rss
on port 0 of the network interface;
[PIPELINE0]
type = MASTER
core = 0
[LINK0]
rss_qs = 0 1
[PIPELINE1]
type = PASS-THROUGH
core = 1
pktq_in = RXQ0.0 RXQ0.1 RXQ1.0
pktq_out = TXQ0.0 TXQ1.0 TXQ0.1
Signed-off-by: Jasvinder Singh <jasvinder.singh@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Corrected a typo in application name.
Corrected authentication algorithm to fit the sample 16-byte
authentication key.
Fixes: ba7b86b1 ("doc: add l2fwd-crypto sample app guide")
Signed-off-by: Fan Zhang <roy.fan.zhang@intel.com>
This patch provides counter mode support to AES-NI multi-buffer library.
The following cipher algorithm is enabled:
- RTE_CRYPTO_CIPHER_AES_CTR
Signed-off-by: Fan Zhang <roy.fan.zhang@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Added possibility for AES to work in counter mode
Signed-off-by: Arek Kusztal <arkadiuszx.kusztal@intel.com>
Acked-by: Deepak Kumar Jain <deepak.k.jain@intel.com>
