The helper rte_eth_dma_zone_reserve() is called by PMDs
when probing a new port.
It creates a new memzone with an unique name.
The name of this memzone was using the name of the driver
doing the probe.
In order to avoid assigning the driver before the end of the probing,
the driver name is removed from these memzone names.
The ethdev name (data->name) is not used because it may be too long
and may be not set at this stage of probing.
Syntax of old name: <driver>_<ring>_<port>_<queue>
Syntax of new name: eth_p<port>_q<queue>_<ring>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Tested-by: Andrew Rybchenko <arybchenko@solarflare.com>
Set the Rx channel map and ingress queue type properly to allow firmware
to manage the internal mapping correctly.
Fixes: 6c2809628c ("net/cxgbe: improve latency for slow traffic")
Cc: stable@dpdk.org
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Add control queue to communicate filter creation/deletion requests
with firmware. This API will be used by subsequent patches.
Signed-off-by: Shagun Agrawal <shaguna@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Update to new Rx/Tx offload API. Always set CRC stripping during
configuration, since it can't be disabled.
Signed-off-by: Shagun Agrawal <shaguna@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
On TX path, add fw_eth_tx_pkt_vm_wr to transmit packets over VF.
Use is_pf4() to correctly calculate the work request size and
offsets within the work request. On RX path, use pktshift to adjust
data offset within the mbuf.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Attach to rte_eth_dev devices allocated by Primary process for
Ports other than Port-0 in the secondary process.
Save the Primary rte_eth_dev device eth_dev_data as part of txq
structure needed for tx path.
Fixes: 8318984927 ("cxgbe: add pmd skeleton")
Cc: stable@dpdk.org
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Create a rte_ethdev_driver.h file and move PMD specific APIs here.
Drivers updated to include this new header file.
There is no update in header content and since ethdev.h included by
ethdev_driver.h, nothing changed from driver point of view, only
logically grouping of APIs. From applications point of view they can't
access to driver specific APIs anymore and they shouldn't.
More PMD specific data structures still remain in ethdev.h because of
inline functions in header use them. Those will be handled separately.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: Andrew Rybchenko <arybchenko@solarflare.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Rename buf_physaddr to buf_iova.
Keep the deprecated name in an anonymous union to avoid breaking
the API.
Signed-off-by: Santosh Shukla <santosh.shukla@caviumnetworks.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Olivier Matz <olivier.matz@6wind.com>
The struct rte_memzone field .phys_addr is renamed to .iova.
The deprecated name is kept in an anonymous union to avoid breaking
the API.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Santosh Shukla <santosh.shukla@caviumnetworks.com>
PKT_RX_VLAN_PKT and PKT_RX_QINQ_PKT are deprecated for a while.
As explained in [1], these flags were kept to let the applications and
PMDs move to the new flag. There is also a need to support Rx vlan
offload without vlan strip (at least for the ixgbe driver).
This patch renames the old flags for this feature, knowing that some
PMDs were using PKT_RX_VLAN_PKT and PKT_RX_QINQ_PKT to indicate that
the vlan tci has been saved in the mbuf structure.
It is likely that some PMDs do not set the proper flags when doing vlan
offload, and it would be worth making a pass on all of them.
Link: [1] http://dpdk.org/ml/archives/dev/2017-June/067712.html
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Fixing typos across dpdk source code using codespell utility.
Skipped the ethdev driver's base code fixes to keep the base
code intact.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
rte_driver->name has the driver name and all physical and virtual
devices has access to it.
Previously it was not possible for virtual ethernet devices to access
rte_driver->name field (because eth_dev used to keep only pci_dev),
and it was required to save driver name in the device private struct.
After re-works on bus and vdev, it is possible for all bus types to
access rte_driver.
It is able to remove the driver name from ethdev device private data and
use eth_dev->device->driver->name.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: Jan Blunck <jblunck@infradead.org>
rmb before determining rsp_type is a bottleneck.
Once we determine rsp-type is FL, we can directly go ahead and read
packets based on q->stat->pidx and budget_left.
This removes bottleneck of rmb once per every RX packet.
Now, rmb exists once per RX batch.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
TX coalescing waits for ETH_COALESCE_PKT_NUM packets to be coalesced
across bursts before transmitting them. For slow traffic, such as
100 PPS, this approach increases latency since packets are received
one at a time and tx coalescing has to wait for ETH_COALESCE_PKT
number of packets to arrive before transmitting.
To fix this:
- Update rx path to use status page instead and only receive packets
when either the ingress interrupt timer threshold (5 us) or
the ingress interrupt packet count threshold (32 packets) fires.
(i.e. whichever happens first).
- If number of packets coalesced is <= number of packets sent
by tx burst function, stop coalescing and transmit these packets
immediately.
Also added compile time option to favor throughput over latency by
default.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Add support for compressed error vector available in cpl_rx_pkt for
Chelsio T6.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Update RX path to reflect Chelsio T6 register value changes.
Update ingress pack boundary value based on maximum payload size
that can be accommodated by underlying PCI. Update ingress pad
boundary value based on smallest memory controller bus width
possible. Enforce alignment for free list pointer start address.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Replace the raw I/O device memory read/write access with eal
abstraction for I/O device memory read/write access to fix
portability issues across different architectures.
CC: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Santosh Shukla <santosh.shukla@caviumnetworks.com>
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Remove the 'name' member from rte_pci_driver and move to generic
rte_driver.
Most of the PMD drivers were initially using DRIVER_REGISTER_PCI(<name>..)
as well as assigning a name to eth_driver.pci_drv.name member.
In this patch, only the original DRIVER_REGISTER_PCI(<name>..) name has
been populated into the rte_driver.name member - assignments through
eth_driver has been removed.
Signed-off-by: Jan Viktorin <viktorin@rehivetech.com>
[Shreyansh: Rebase and expand changes to newly added files]
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: David Marchand <david.marchand@6wind.com>
Macros RTE_MBUF_DATA_DMA_ADDR and RTE_MBUF_DATA_DMA_ADDR_DEFAULT
are defined in each PMD driver file. Convert macros to inline
functions and move them to common lib/librte_mbuf/rte_mbuf.h file.
PMD drivers include rte_mbuf.h file directly/indirectly hence no
additioanl header file inclusion is necessary.
Signed-off-by: Ravi Kerur <rkerur@gmail.com>
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
When refilling freelists for the first time and if it fails, the rxq
is freed and returns ENOMEM. There is a check while freeing hardware rxq
to pass freelist context id if the freelist exists or 0xffff otherwise.
The error path is only reached if freelist exists. So, fix is to remove
the useless check for freelist existence.
Coverity issue: 107108
Fixes: 92c8a63223 ("cxgbe: add device configuration and Rx support")
Reported-by: John McNamara <john.mcnamara@intel.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
CXGBE PMD depends on an alarm to periodically transmit any pending
coalesced packets and hence spins for a lock for each tx queue in the
alarm callback.
A better solution is to try to get a lock whenever possible, instead
of spinning for it.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Ensure jumbo mode is enabled and that the mbuf data room size can
accommodate jumbo size. If the mbuf data room size can't accommodate
jumbo size, chain mbufs to jumbo size.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Add a non-coalesce path. Skip coalescing for Jumbo Frames, and send the
packet through non-coalesced path if there are enough credits. Also,
free these non-coalesced packets while reclaiming credits.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Update sge initialization with respect to free-list manager configuration
and ingress arbiter. Also update refill logic to refill mbufs only after
a certain threshold for rx. Optimize tx packet prefetch.
Approx. 3 MPPS improvement seen in forwarding performance after the
optimization.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
The extended unified packet type is now part of the standard ABI.
As mbuf struct is changed, the mbuf library version is incremented.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Fix "MACRO redefined" and "function redefined" compilation errors in FreeBSD
by adding CXGBE prefix to them. Also remove reference to a linux header
linux/if_ether.h and use DPDK macros directly. Finally, enable CXGBE PMD
for FreeBSD.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
To unify packet types among all PMDs, bit masks of packet type for
'ol_flags' are replaced by unified packet type.
To avoid breaking ABI compatibility, all the changes would be enabled
by RTE_NEXT_ABI.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
CXGBE PMD rx allocates a new mbuf everytime, which could lead to performance
hit. Instead, do bulk allocation of mbufs and re-use them.
Also, simplify the overall rx-handler, and update its logic to fix rx perf.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
When compiling the cxgbe driver with icc, multiple errors about using
enums as integers appear across a number of files, including in the base
code and in the DPDK-specific driver code.
.../drivers/net/cxgbe/cxgbe_main.c(386): error #188: enumerated type mixed
with another type
t4_get_port_type_description(pi->port_type));
^
For the errors in the base driver code we use the CFLAGS_BASE_DRIVER
approach used by other drivers to disable warnings.
For errors in the DPDK-specific code, typecasts are used to fix the
errors in the code itself.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Adds cxgbe poll mode driver for DPDK under drivers/net/cxgbe directory.
This patch:
1. Adds the Makefile to compile cxgbe pmd.
2. Registers and initializes the cxgbe pmd driver.
Enable cxgbe PMD for compilation and linking with changes to:
1. config/common_linuxapp to add macros for cxgbe pmd.
2. drivers/net/Makefile to add cxgbe pmd to the compile list.
3. mk/rte.app.mk to add cxgbe pmd to link.
Update MAINTAINERS file to claim responsibility for the cxgbe PMD.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
[Thomas: add disabled config for bsdapp]
