The drivers for OCTEON TX2 are not supported in 32-bit mode.
Suggested-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Jerin Jacob <jerinj@marvell.com>
These entry points are NO-OPS. DLB does not support
reconfiguring individual queues or ports. The entire device
must be reconfigured.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Add a variety of self-tests for both ldb and directed
ports/queues, as well as configure, start, stop, link, etc...
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
The PMD uses a public interface to allow applications to
control the token pop mode. Supported token pop modes are
as follows, and they impact core scheduling affinity for
ldb ports.
AUTO_POP: Pop the CQ tokens immediately after dequeueing.
DELAYED_POP: Pop CQ tokens after (dequeue_depth - 1) events
are released. Supported on load-balanced ports
only.
DEFERRED_POP: Pop the CQ tokens during next dequeue operation.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Add support for eventdev stop and close entry points.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Add support for dequeue, dequeue_burst, ...
DLB does not currently support interrupts, but instead uses
umonitor/umwait if supported by the processor. This allows
the software to monitor and wait on writes to a cache-line.
DLB supports normal and sparse cq mode. In normal mode the
hardware will pack 4 QEs into each cache line. In sparse cq
mode, the hardware will only populate one QE per cache line.
Software must be aware of the cq mode, and take the appropriate
actions, based on the mode.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Add support for the eventdev start entry point.
DLB delays setting up single link resources until
eventdev start, because it is only then that it can
ascertain which ports have just one linked queue.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Add supports for the port unlink(s) eventdev entry points.
The unlink operation is an asynchronous operation executed by
a control thread, and the unlinks-in-progress function reads
a counter shared with the control thread. Port QE and memzone
memory is freed here.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Add port link entry point. Directed queues are identified and created
at this stage. Their setup deferred until link-time, at which
point we know the directed port ID. Directed queue setup
will only fail if this queue is already setup or there are
no directed queues left to configure.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Configure the load balanced (ldb) or directed (dir) port.
The consumer queue (CQ) and producer port (PP) are also
set up here.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Load balanced (ldb) queues are setup here.
Directed queues are not set up until link time, at which
point we know the directed port ID. Directed queue setup
will only fail if this queue is already setup or there are
no directed queues left to configure.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Add support for getting the queue and port default configuration.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Add support for configuring the DLB hardware.
In particular, this patch configures the DLB
hardware's scheduling domain, such that it is provisioned with
the requested number of ports and queues, provided sufficient
resources are available. Individual queues and ports are
configured later in port setup and eventdev start.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
This commit adds probe-time low level hardware
initialization. It also adds probe-time init for both
primary and secondary DPDK processes.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
This commit introduces the flexible interface. This
interface allows the core code to operate in PF mode (direct
hardware access) or bifurcated mode (hardware configured via
kernel driver). This driver currently only supports PF modei,
but bifurcated mode will be added in a future patch-set.
Note that the flexible interface is not used for data path
operations, and thus there are no performance concerns
related to the use of function pointers.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Add the eventdev portion of probe, and parse command line
options, but do not initialize hardware.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Add miscellaneous inline functions that may be called
from multiple files. These functions include inline
assembly of new x86 instructions, such as movdir64b,
since they are not available as builtin functions in
the minimum supported GCC version.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Add headers containing structs and constants shared between
the PMD and the shared code. The term shared code refers to
the code that implements the hardware interface. The shared code
is introduced in the probe patch, and then is extended as
additional eventdev PMD entry points are added to the patchset.
In the case of the bifurcated PMD (to be introduced in the
future), the shared code is contained in the Linux kernel
module itself.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Add headers used internally by the PMD. They include constants,
macros for device resources, structure definitions for hardware interfaces
and software state, and various forward-declarations.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
This commit adds base support for dynamic logging.
The default log level is NOTICE. Dynamic logging
is used exclusively throughout this patchset.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Note that config/rte_config.h contains several configuration
switches, providing for fine control of the PMD's
runtime behaviour.
The meson infrastructure is expanded as additional files are
added to this patchset.
Adds announcement of availability of the new driver
for Intel Dynamic Load Balancer 1.0 hardware.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
DLB does not support reconfiguring individual queues
or ports on the fly. The entire device must be reconfigured.
Previously allocated port QE and memzone memory
is freed in this patch.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Add a variety of self-tests for both ldb and directed
ports/queues, as well as configure, start, stop, link, etc...
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
The PMD uses a public interface to allow applications to
control the token pop mode. Supported token pop modes are
as follows, and they impact core scheduling affinity for
ldb ports.
AUTO_POP: Pop the CQ tokens immediately after dequeueing.
DELAYED_POP: Pop CQ tokens after (dequeue_depth - 1) events
are released. Supported on load-balanced ports
only.
DEFERRED_POP: Pop the CQ tokens during next dequeue operation.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Add support for eventdev stop and close entry points.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Add support for dequeue, dequeue_burst, ...
DLB2 does not currently support interrupts, but instead use
umonitor/umwait if supported by the processor. This allows
the software to monitor and wait on writes to a cache-line.
DLB2 supports normal and sparse cq mode. In normal mode the
hardware will pack 4 QEs into each cache line. In sparse cq
mode, the hardware will only populate one QE per cache line.
Software must be aware of the cq mode, and take the appropriate
actions, based on the mode.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Add support for the eventdev start entry point.
We delay initializing some resources until
eventdev start, since the number of linked queues can be
used to determine if we are dealing with a ldb or dir resource.
If this is a device restart, then the previous configuration
will be reapplied.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Add supports for the port unlink(s) eventdev entry points.
The unlink operation is an asynchronous operation executed by
a control thread, and the unlinks-in-progress function reads
a counter shared with the control thread.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Add port link entry point. Directed queues are identified and created
at this stage. Their setup deferred until link-time, at which
point we know the directed port ID. Directed queue setup
will only fail if this queue is already setup or there are
no directed queues left to configure.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Configure the load balanced (ldb) or directed (dir) port.
The consumer queue (CQ) and producer port (PP) are also
set up here.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Load balanced (ldb) queues are setup here.
Directed queues are not set up until link time, at which
point we know the directed port ID. Directed queue setup
will only fail if this queue is already setup or there are
no directed queues left to configure.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Add support for getting the queue and port default configuration.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Add support for configuring the DLB2 hardware.
In particular, this patch configures the DLB2
hardware's scheduling domain, such that it is provisioned with
the requested number of ports and queues, provided sufficient
resources are available. Individual queues and ports are
configured later in port setup and eventdev start.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
This commit adds probe-time low level hardware
initialization. It also adds probe-time init for both
primary and secondary DPDK processes.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
This commit introduces the flexible interface. This
interface allows the core code to operate in PF mode (direct
hardware access) or bifurcated mode (hardware configured via
kernel driver). This driver currently only supports PF mode
but bifurcated mode will be added in a future DPDK patch-set.
Note that the flexible interface is not used for data path
operations, and thus there are no performance concerns
related to the use of function pointers.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Add the eventdev portion of probe, and parse command line
options, but do not initialize hardware.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Add miscellaneous inline functions that may be called
from multiple files. These functions include inline
assembly of new x86 instructions, such as movdir64b,
since they are not available as builtin functions in
the minimum supported GCC version.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Add headers containing structs and constants shared between
the PMD and the shared code. The term shared code refers to
the code that implements the hardware interface. The shared code
is introduced in the probe patch, and then is extended as
additional eventdev PMD entry points are added to the patchset.
In the case of the bifurcated PMD (to be introduced in the
future), the shared code is contained in the Linux kernel
module itself.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
The header file dlb2_priv.h is used internally by the PMD.
It include constants, macros for device resources,
structure definitions for hardware interfaces and
software state, and various forward-declarations.
The header file rte_pmd_dlb2.h will be exported in a
subsequent patch, but is included here due to a data
structure dependency.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
This commit adds base support for dynamic logging.
The default log level is NOTICE. Dynamic logging
is used exclusively throughout this patchset.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
