Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
Does not implement any deprecated statistics.
No per-queue statistics yet.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
Supported options are auto (based on NIC firmware variant and
installed licences), throughput, low-latency.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
The PMD allows for DPDK and the host to communicate using a raw
device interface on the host and in the DPDK application. The device
created is a Tap device with a L2 packet header.
Signed-off-by: Keith Wiles <keith.wiles@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Tested-by: Aws Ismail <aismail@ciena.com>
Tested-by: Vasily Philipov <vasilyf@mellanox.com>
remove the following API's:
rte_eth_dev_set_vf_rxmode
rte_eth_dev_set_vf_rx
rte_eth_dev_set_vf_tx
rte_eth_dev_set_vf_vlan_filter
rte_eth_dev_set_vf_rate_limit
Increment LIBABIVER in Makefile
Remove deprecation notice for removing rte_eth_dev_set_vf_* API's.
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Check that Rx mbuf pool, MTU and Rx scatter config are in sync.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Resources required in accordance with configuration are
allocated only.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Manual link speed/duplex configuration is not supported yet.
Loopback is not supported yet.
Flow Director is not supported.
Link status change notification using interrupt is not supported yet.
Receive data notification using interrupts is not supported yet.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Enable the PMD by default on supported configurations.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
This patch adds a new function eth_igb_fw_version_get.
Signed-off-by: Qiming Yang <qiming.yang@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
This patch adds a new API 'rte_eth_dev_fw_version_get' for
fetching firmware version by a given device.
Signed-off-by: Qiming Yang <qiming.yang@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Last changes in Niantic and Fortville NIC drivers causes that
vector Rx path is chosen by default in l3fwd-thread application.
This path doesn't support propagation of hw packet type recognition
to the packet_type field in mbuf, and packets cannot be classified
properly.
The approach to solve this problem is similar to the commit:
71a7e2424e ("examples/l3fwd: fix using packet type blindly").
To use sw packet analyzer, new command line option "--parse-ptype" is
introduced.
Signed-off-by: Tomasz Kulasek <tomaszx.kulasek@intel.com>
A referenced document in the Linux Kernel has been moved to a
sub-directory. And kernel community has moved to RST/Sphinx. The links are
replaced with HTML rendered links.
Signed-off-by: Yongseok Koh <yskoh@mellanox.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
L3 Forwarding sample app user guides have some inconsistencies
between the example command line and the configuration table.
Also, they were showing too complicated configuration, using two
different NUMA nodes for two ports, which will probably lead
to performance drop due to use cross-socket channel.
This patch simplifies the configuration of these examples,
by using a single NUMA node and a single queue per port.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
This patch fixes a trivial typo in testpmd application guide.
Signed-off-by: Rami Rosen <rami.rosen@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
This patch mainly allocates structure to store queue/irq mapping,
and configure queue/irq mapping down through PCI ops. It also creates
eventfds for each Rx queue and tell the kernel about the eventfd/intr
binding.
Note: So far, we hard-code 1:1 queue/irq mapping (each rx queue has
one exclusive interrupt), like this:
vec 0 -> config irq
vec 1 -> rxq0
vec 2 -> rxq1
...
which means, the "vectors" option of QEMU should be configured with
a value >= N+1 (N is the number of the queue pairs).
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Tested-by: Lei Yao <lei.a.yao@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
This patch add support vhost kernel as the backend for virtio_user.
Three main hook functions are added:
- vhost_kernel_setup() to open char device, each vq pair needs one
vhostfd;
- vhost_kernel_ioctl() to communicate control messages with vhost
kernel module;
- vhost_kernel_enable_queue_pair() to open tap device and set it
as the backend of corresonding vhost fd (that is to say, vq pair).
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
The introduce of virtio 1.0 support brings yet another set of ops, badly,
it's not handled correctly, that it breaks the multiple process support.
The issue is the data/function pointer may vary from different processes,
and the old used to do one time set (for primary process only). That
said, the function pointer the secondary process saw is actually from the
primary process space. Accessing it could likely result to a crash.
Kudos to the last patches, we now be able to maintain those info that may
vary among different process locally, meaning every process could have its
own copy for each of them, with the correct value set. And this is what
this patch does:
- remap the PCI (IO port for legacy device and memory map for modern
device)
- set vtpci_ops correctly
After that, multiple process would work like a charm. (At least, it
passed my fuzzy test)
Fixes: b8f04520ad ("virtio: use PCI ioport API")
Fixes: d5bbeefca8 ("virtio: introduce PCI implementation structure")
Fixes: 6ba1f63b5a ("virtio: support specification 1.0")
Cc: stable@dpdk.org
Reported-by: Juho Snellman <jsnell@iki.fi>
Reported-by: Yaron Illouz <yaroni@radcom.com>
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Below MACsec offload commands are added:
- set macsec offload <port_id> on encrypt on|off replay-protect on|off
- set macsec offload <port_id> off
- set macsec sc tx|rx <port_id> <mac> <pi>
- set macsec sa tx|rx <port_id> <idx> <an> <pn> <key>
Also update the testpmd user guide.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
MACsec (or LinkSec, 802.1AE) is a MAC level encryption/authentication
scheme defined in IEEE 802.1AE that uses symmetric cryptography.
This commit adds the MACsec offload support for ixgbe.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Attaching and detaching ethernet ports from an application
is not the same thing as physically removing a PCI device,
so clarify the flags indicating support. All PCI devices
are assumed to be physically removable, so no flag is
necessary in the PCI layer.
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
Leaving default pattern item mask values up for interpretation by PMDs is
an undefined behavior that applications might find difficult to use in the
wild. It also needlessly complicates PMD implementation.
This commit addresses this by defining consistent default masks for each
item type.
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Contrary to the current description, mbuf RSS hash result storage does not
overlap with the returned MARK value (hash.fdir.lo vs. hash.fdir.hi), and
both may be combined.
Reflect this change by allowing testpmd to display both values
simultaneously.
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Both actions share the PKT_RX_FDIR mbuf flag, as a result there is no way
to tell them apart. Moreover, the maximum allowed value for the MARK action
may not necessarily cover the entire 32-bit space.
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Add common vector type definitions to all CPU architectures.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Acked-by: Chao Zhu <chaozhu@linux.vnet.ibm.com>
Rename tools/ into usertools/ to differentiate from buildtools/
and devtools/ while making clear these scripts are part of
DPDK runtime.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Tested-by: Ferruh Yigit <ferruh.yigit@intel.com>
The remaining scripts in the scripts/ directory are only useful
to developers. That's why devtools/ is a better name.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Tested-by: Ferruh Yigit <ferruh.yigit@intel.com>
There is already a directory buildtools for pmdinfogen used by
the build system. The scripts used in makefiles are moved here.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Tested-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add a requirement to support both Python 2 and 3 to the
DPDK Python Coding Standards and Getting started Guide.
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Make all DPDK python application compliant with the PEP8 standard
to allow for consistency checking of patches and to allow further
refactoring.
Signed-off-by: John McNamara <john.mcnamara@intel.com>
This commit exposes the following item fields through the flow command:
- VLAN priority code point, drop eligible indicator and VLAN identifier
(all part of TCI).
- IPv4 type of service, time to live and protocol.
- IPv6 traffic class, flow label, next header and hop limit.
- SCTP tag and checksum.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Document syntax, interaction with rte_flow and provide usage examples.
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Acked-by: Olga Shern <olgas@mellanox.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
They are superseded by the generic flow API (rte_flow). Target release is
not defined yet.
Suggested-by: Kevin Traynor <ktraynor@redhat.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Acked-by: Olga Shern <olgas@mellanox.com>
This new API supersedes all the legacy filter types described in
rte_eth_ctrl.h. It is slightly higher level and as a result relies more on
PMDs to process and validate flow rules.
Benefits:
- A unified API is easier to program for, applications do not have to be
written for a specific filter type which may or may not be supported by
the underlying device.
- The behavior of a flow rule is the same regardless of the underlying
device, applications do not need to be aware of hardware quirks.
- Extensible by design, API/ABI breakage should rarely occur if at all.
- Documentation is self-standing, no need to look up elsewhere.
Existing filter types will be deprecated and removed in the near future.
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Acked-by: Olga Shern <olgas@mellanox.com>
Doing a device information query on a non-PCI device such as
vhost was resulting in the dereferencing of a NULL pointer
(the absent PCI data), causing a segmentation fault.
Fixes: bda68ab9d1 ("examples/ethtool: add user-space ethtool sample application")
Signed-off-by: Remy Horton <remy.horton@intel.com>
This patch fixes a trivial typo in testpmd application user guide.
Signed-off-by: Rami Rosen <rami.rosen@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
DPDK source archives are .tar.xz or .tar.gz, not .zip. Use .tar.xz in the
instructions, since that is what the main download page links to.
Also, correct the archive file and directory name capitalization.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: John McNamara <john.mcnamara@intel.com>
The Python requirement should appear in the bullet list.
Also, indent the x32 note, since it is related to the previous bullet.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: John McNamara <john.mcnamara@intel.com>
Add a new section to the Code Contributors Guide to outline
the roles of tree and component maintainers and how they
can be added and removed.
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Having reference benchmarks is important in order to obtain
reproducible performance figures.
This patch describes required steps to configure a PVP setup
using testpmd in both host and guest.
Not relying on external vSwitch ease integration in a CI loop by
not being impacted by DPDK API changes.
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Acked-by: Kevin Traynor <ktraynor@redhat.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
There was an option CONFIG_RTE_INSECURE_FUNCTION_WARNING (disabled by
default), which prevents from using some libc functions:
sprintf, snprintf, vsnprintf, strcpy, strncpy, strcat, strncat, sscanf,
strtok, strsep and strlen.
It's all about using them at the right place with the right precautions.
However, it is neither really possible nor a good advice to disable them.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Since commit 4a96e8b652 ("mbuf: allow to clone an indirect mbuf")
attaching to an indirect mbuf creates a clone of that mbuf. Update the mbuf
documentation to match.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: John McNamara <john.mcnamara@intel.com>
- Remove wrong document description:
The Programmer’s Guide intro is not the Release Notes.
- Fix heading of section which only deals with Tx queues configuration.
- Fix wrong verbatim text paragraphs:
Reduce the indentation of these paragraphs since they are not part of the
verbatim block.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: John McNamara <john.mcnamara@intel.com>
Fix relative path between sphinx conf.py file and Nic table file
to allow automatic build on ReadTheDocs.
Fixes: 9db3f52126 ("doc: generate NIC overview table from ini files")
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Tested-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Today, all logs whose level is lower than INFO are dropped at
compile-time. This prevents from enabling debug logs at runtime using
--log-level=8.
The rationale was to remove debug logs from the data path at
compile-time, avoiding a test at run-time.
This patch changes the behavior of RTE_LOG() to avoid the compile-time
optimization, and introduces the RTE_LOG_DP() macro that has the same
behavior than the previous RTE_LOG(), for the rare cases where debug
logs are in the data path.
So it is now possible to enable debug logs at run-time by just
specifying --log-level=8. Some drivers still have special compile-time
options to enable more debug log. Maintainers may consider to
remove/reduce them.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Add template release notes for DPDK 17.02 with inline
comments and explanations of the various sections.
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
DPDK switched to main and sub-repositories approach, this patch
documents new approach and updates development process according.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Rearrange the order of the high level documenation index into
a more logical sequence for a new user.
Also, improve some of the high-level document names.
Signed-off-by: John McNamara <john.mcnamara@intel.com>
This patch adds a notice that the ABI change for ethtool app to
get the NIC firmware version in the 17.02 release.
Signed-off-by: Qiming Yang <qiming.yang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Beilei Xing <beilei.xing@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
In 17.02 five rte_eth_dev_set_vf_*** functions will be removed
from librte_ether, renamed and moved to the ixgbe PMD.
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Reshma Pattan <reshma.pattan@intel.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
The _rte_eth_dev_call_process function will change to return "int"
and a fourth parameter "void* ret_param" will be added. This change
targets release 17.02.
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
In igb_uio, iomem is mapped, and both ioport and io mem are recorded
into uio framework (then into sysfs files), which is duplicated with
what Linux has already provided for user space, and makes the code
too complex.
For iomem, DPDK user space code never opens or reads files under
/sys/pci/bus/devices/xxxx:xx:xx.x/uio/uioY/maps/. Instead,
/sys/pci/bus/devices/xxxx:xx:xx.x/resourceY are used to map device
memory.
For ioport, non-x86 platforms cannot read from files under
/sys/pci/bus/devices/xxxx:xx:xx.x/uio/uioY/portio/ directly, because
non-x86 platforms need to map port region for access in user space,
see non-x86 version pci_uio_ioport_map(). x86 platforms can use the
the same way as uio_pci_generic.
This will remove iomem and ioport mapping in igb_uio kernel module,
and adjusts the iomem implementation in both igb_uio and
uio_pci_generic:
- for x86 platform, get ports info from /proc/ioports;
- for non-x86 platform, map and get ports info by pci_uio_ioport_map().
Note: this will affect those applications who are using files under
/sys/pci/bus/devices/xxxx:xx:xx.x/uio/uioY/maps/ and
/sys/pci/bus/devices/xxxx:xx:xx.x/uio/uioY/portio/.
Suggested-by: Ferruh Yigit <ferruh.yigit@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Add more tested platforms and nics and OSes to the release notes.
Signed-off-by: Yulong Pei <yulong.pei@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Issue is with the digest appended feature on QAT PMD.
A workaround is also documented.
Signed-off-by: Fiona Trahe <fiona.trahe@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: John Griffin <john.griffin@intel.com>
- Fix to use bitmapped values in NVM configuration for speed capability
advertisement. This issue is specific to 25G NIC since it is capable
of 25G and 10G speeds.
- Update feature list.
Fixes: 64c239b7f8 ("net/qede: fix advertising link speed capability")
Signed-off-by: Harish Patil <harish.patil@qlogic.com>
83xx NIC subsystem differs in new PCI subsystem_device_id and
NICVF_CAP_DISABLE_APAD capability.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Jianbo Liu <jianbo.liu@linaro.org>
The l3fwd application route lookup mode can be selected at run time
but not at compile time. This patch corrects the statement in the doc.
Fixes: d0dff9ba ("doc: sample application user guide")
Signed-off-by: Reshma Pattan <reshma.pattan@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
The changes for the feature "Tx prepare" should be made in version 17.02.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Tomasz Kulasek <tomaszx.kulasek@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
L3fwd-power app needs vector mode to be disabled in order to work
properly. The app used to work previously, because it was using
Rx scalar function, but now it uses vector function.
Vector mode needs to be disabled to make the app works,
which has been documented in release notes.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
multi-process support has been verified on non IA such as ARMv8.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Fixes typos present in the documentation and code comments.
Signed-off-by: Alain Leon <xerebz@gmail.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Add list of tested and validated NICs too.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Fixes: 75ef62a943 ("net/mlx5: fix link speed capability information")
Fixes: 1884087198 ("net/mlx5: fix support for newer link speeds")
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Turning off S-TAG identification will impact floating VEB,
VFs can't communicate with each other.
This patch fixes this issue by judging whether floating
VEB is enabled, S-TAG identification will be turned off
only when floating VEB is disabled.
Fixes: 4d61120d5c ("net/i40e: fix dropping packets with ethertype 0x88A8")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Add information about new ixgbe PMD API.
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
For vhost-switch sample, the old guide takes too many words on
vhost-cuse, which is mainly due to vhost-cuse is invented before
vhost-user.
Now vhost-cuse is removed, meaning the best part of the doc is useless.
Instead of amending one piece here and there, this patch simply removes
the most part of the doc and replace it with a simple test guide.
For tep_term sample, mainly for removing the part has "vhost-cuse".
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
vhost-cuse has been removed in this release. Update the doc, with the
vhost-cuse part being removed.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
The library was named libethdev without rte_ prefix.
It is now fixed, the library namespace is consistent.
Note: the ABI version has already been changed in this release cycle.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
rte_device/driver generalization patches [1] were merged without a change
in the LIBABIVER variable. This patches bumps the macro of affected libs:
- libcryptodev and libetherdev have been bumped
- librte_eal version changed in
d7e61ad3ae ("log: remove deprecated history dump")
Details of ABI/API changes:
- EAL [version already bumped in: d7e61ad3ae]
|- type field was removed from rte_driver
|- rte_pci_device now embeds rte_device
|- rte_pci_resource renamed to rte_mem_resource
|- numa_node and devargs of rte_pci_driver is moved to rte_driver
|- APIs for device hotplug (attach/detach) moved into EAL
|- API rte_eal_pci_device_name added for PCI device naming
|- vdev registration API introduced (rte_eal_vdrv_register,
| rte_eal_vdrv_unregister
- librte_crypto (v 1=>2)
|- removed rte_cryptodev_create_unique_device_name API
|- moved device naming to EAL
- librte_ethdev (v 4=>5)
|- rte_eth_dev_type is removed
|- removed dev_type from rte_eth_dev_allocate API
|- removed API rte_eth_dev_get_device_type
|- removed API rte_eth_dev_get_addr_by_port
|- removed API rte_eth_dev_get_port_by_addr
|- removed rte_cryptodev_create_unique_device_name API
|- moved device naming to EAL
Also, deprecation notice from 16.07 has been removed and release notes for
16.11 added.
[1] http://dpdk.org/ml/archives/dev/2016-September/047087.html
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
This summarizes the "how to call dpdk-devbind" in one place to be
picked up by html/pdf/man-page docs.
That knowledge was available before but spread in various docs along
examples (which are great and have to be kept) as well as in the
--usage/--help option of the tool itself.
As a root only program in sbin it should belong to section 8
"8 System administration commands (usually only for root)"
Signed-off-by: Christian Ehrhardt <christian.ehrhardt@canonical.com>
Acked-by: Luca Boccassi <lboccass@brocade.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
This summarizes the "how to call dpdk-pmdinfo" in one place to be picked
up by html/pdf/man-page docs.
Signed-off-by: Christian Ehrhardt <christian.ehrhardt@canonical.com>
Acked-by: Luca Boccassi <lboccass@brocade.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
This enables the rendering of rst into man pages as well as installing
them (if built) along the binaries. To do so there is a new make target
"doc-guides-man" which will render the rst files into man format.
Currently these three tools had docs that were compatible "enough" to
make up for a reasonable manpage.
- testpmd
- dpdk-pdump
- dpdk-procinfo
Since a man page should be installed along the binary they are not
installed in install-doc but install-runtime insteade. If not explicitly
built by the "doc-guides-man" target before calling install-runtime
there is no change to the old behaviour.
Signed-off-by: Christian Ehrhardt <christian.ehrhardt@canonical.com>
Acked-by: Luca Boccassi <lboccass@brocade.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
This is to clarify the scope of these documents that are more tools than
sample applications.
Also this is a preparation step to add more tools and generate man pages
off of their rst files.
Signed-off-by: Christian Ehrhardt <christian.ehrhardt@canonical.com>
Acked-by: Luca Boccassi <lboccass@brocade.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
The note i.e. "The dpdk-pdump tool can only be used in
conjunction with a primary process which has the packet
capture framework initialized already" is added to
doc/guides/sample_app_ug/pdump.rst to facilitate
easy understanding on the usage of the tool.
Suggested-by: Jianfeng Tan <jianfeng.tan@intel.com>
Signed-off-by: Reshma Pattan <reshma.pattan@intel.com>
This patch replaces name "libcrypto" to "openssl" from file directories,
symbol prefixes and sub-names connected with old name.
Renamed poll mode driver files, test files, and documentations.
It is done to better name association with library because
the cryptography operations are using Openssl library crypto API.
Fixes: d61f70b4c9 ("crypto/libcrypto: add driver for OpenSSL library")
Signed-off-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Acked-by: Deepak Kumar Jain <deepak.k.jain@intel.com>
