Batch more than one Tx requests such that only one completion
is generarted by the HW. We request a Tx completion for first
and last Tx request in the batch.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
PORT_CLR_STATS is not allowed for VFs, NPAR, MultiHost functions
or when SR-IOV is enabled.
Don't send the HWRM command in such cases.
Fixes: bfb9c2260b ("net/bnxt: support xstats get/reset")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
DEV_RX_OFFLOAD_KEEP_CRC offload flag is added. PMDs that support
keeping CRC should advertise this offload capability.
DEV_RX_OFFLOAD_CRC_STRIP flag will remain one more release
default behavior in PMDs are to keep the CRC until this flag removed
Until DEV_RX_OFFLOAD_CRC_STRIP flag is removed:
- Setting both KEEP_CRC & CRC_STRIP is INVALID
- Setting only CRC_STRIP PMD should strip the CRC
- Setting only KEEP_CRC PMD should keep the CRC
- Not setting both PMD should keep the CRC
A helper function rte_eth_dev_is_keep_crc() has been added to be able to
change the no flag behavior with minimal changes in PMDs.
The PMDs that doesn't report the DEV_RX_OFFLOAD_KEEP_CRC offload can
remove rte_eth_dev_is_keep_crc() checks next release, related code
commented to help the maintenance task.
And DEV_RX_OFFLOAD_CRC_STRIP has been added to virtual drivers since
they don't use CRC at all, when an application requires this offload
virtual PMDs should not return error.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Allain Legacy <allain.legacy@windriver.com>
Acked-by: Andrew Rybchenko <arybchenko@solarflare.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
The xstats API expects that the driver fills both values and ids for
each filled entries.
Fixes: bfb9c2260b ("net/bnxt: support xstats get/reset")
Cc: stable@dpdk.org
Signed-off-by: David Marchand <david.marchand@6wind.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
For frames where the hardware is not able to calculate checksum
we are indicating such frames to be bad. And that is incorrect.
Indicate PKT_RX_IP_CKSUM_UNKNOWN or PKT_RX_L4_CKSUM_UNKNOWN
for such frames.
Fixes: 7ec39d8c52 ("net/bnxt: update status of Rx IP/L4 CKSUM")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Query of port stats is permitted for VF interfaces as well.
Fix the code to allow VFs to query port stats.
Fixes: bfb9c2260b ("net/bnxt: support xstats get/reset")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
If the resource requirement of a VF is more than what is allotted
to it by the FW, a VF can request to reallocate some of the resources.
This is possible only when the NIC is running the Resource Manager aware
CHiMP FW.
If necessary, calculate Tx and Rx ring count using the new RM API.
Otherwise use the Tx and Rx ring count as-is. Update the cp ring count
based on the Tx and Rx ring count.
Fixes: b7778e8a1c ("net/bnxt: refactor to properly allocate resources for PF/VF")
Signed-off-by: Jay Ding <jay.ding@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Randy Schacher <stuart.schacher@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
In order to save completion resource, use the first completion ring from
PF or VF as the default completion ring for async event & HWRM forward
response handling. Add bnxt_hwrm_set_async_event_cr() to set
async_event_cr for either PF or VF.
Fixes: 7bc8e9a227 ("net/bnxt: support async link notification")
Signed-off-by: Qingmin Liu <qingmin.liu@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
While configuring RSS, the FW needs to know the rss_hash_mode that needs
to be initialized.
Set hash mode to HWRM_VNIC_RSS_CFG_INPUT_HASH_MODE_FLAGS_DEFAULT
to allow the FW to use the global mode already configured in the device.
Fixes: bcd4bcc442 ("net/bnxt: configure RSS")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
We were initializing Tx and Rx burst functions only for primary
processes. Fixing it in this patch.
Fixes: 8892013668 ("net/bnxt: support xstats get by id")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
The FALLTHROUGH comment for cascading switch cases was missing in
a few places. This patch adds that.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
This patch check if a input requested offloading is valid or not.
Any reuqested offloading must be supported in the device capabilities.
Any offloading is disabled by default if it is not set in the parameter
dev_conf->[rt]xmode.offloads to rte_eth_dev_configure() and
[rt]x_conf->offloads to rte_eth_[rt]x_queue_setup().
If any offloading is enabled in rte_eth_dev_configure() by application,
it is enabled on all queues no matter whether it is per-queue or
per-port type and no matter whether it is set or cleared in
[rt]x_conf->offloads to rte_eth_[rt]x_queue_setup().
If a per-queue offloading hasn't be enabled in rte_eth_dev_configure(),
it can be enabled or disabled for individual queue in
ret_eth_[rt]x_queue_setup().
A new added offloading is the one which hasn't been enabled in
rte_eth_dev_configure() and is reuqested to be enabled in
rte_eth_[rt]x_queue_setup(), it must be per-queue type,
otherwise trigger an error log.
The underlying PMD must be aware that the requested offloadings
to PMD specific queue_setup() function only carries those
new added offloadings of per-queue type.
This patch can make above such checking in a common way in rte_ethdev
layer to avoid same checking in underlying PMD.
This patch assumes that all PMDs in 18.05-rc2 have already
converted to offload API defined in 17.11 . It also assumes
that all PMDs can return correct offloading capabilities
in rte_eth_dev_infos_get().
In the beginning of [rt]x_queue_setup() of underlying PMD,
add offloads = [rt]xconf->offloads |
dev->data->dev_conf.[rt]xmode.offloads; to keep same as offload API
defined in 17.11 to avoid upper application broken due to offload
API change.
PMD can use the info that input [rt]xconf->offloads only carry
the new added per-queue offloads to do some optimization or some
code change on base of this patch.
Signed-off-by: Wei Dai <wei.dai@intel.com>
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
This patch adds new NVM specific HWRM commands.
Code using these commands will be added in future patches.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Add HWRM structures to support more filtering features
like metering, tunnel filters and more.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Clear HWRM sniffer list for DPDK PFs so that VFs on
DPDK PFs initialize successfully. DPDK PF driver does not
handle HWRM commands from VFs.
Signed-off-by: Randy Schacher <stuart.schacher@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
VNIC ID returned by the FW is a 16-bit field.
We are incorrectly using it as a 32-bit value in few places.
This patch corrects that.
Fixes: daef48efe5 ("net/bnxt: support set MTU")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Michael Wildt <michael.wildt@broadcom.com>
Reviewed-by: Randy Schacher <stuart.schacher@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
In the start/stop_op operation, mbufs allocated for rings were not freed
1) add bnxt_free_tx_mbuf/bnxt_free_rx_mbuf in bnxt_dev_stop_op to free MBUF
before freeing the rings.
2) MBUF allocation and free routines were not in sync. Allocation uses the
ring->ring_size including any rounded up and multiple factors while the
free routine uses the requested queue size.
Fixes: c09f57b49c ("net/bnxt: add start/stop/link update operations")
Cc: stable@dpdk.org
Signed-off-by: Jay Ding <jay.ding@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Randy Schacher <stuart.schacher@broadcom.com>
Signed-off-by: Xiaoxin Peng <xiaoxin.peng@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
clear flag on stop at proper location to avoid race conditions.
Fixes: ed2ced6fe9 ("net/bnxt: check initialization before accessing stats")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
return error if init is not complete before accessing stats.
Fixes: ed2ced6fe9 ("net/bnxt: check initialization before accessing stats")
Cc: stable@dpdk.org
Signed-off-by: Jay Ding <jay.ding@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Randy Schacher <stuart.schacher@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
We were not considering the case of nested VLANs while
calculating MTU. This patch takes care of the same.
Fixes: daef48efe5 ("net/bnxt: support set MTU")
Cc: stable@dpdk.org
Signed-off-by: Qingmin Liu <qingmin.liu@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Jay Ding <jay.ding@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Randy Schacher <stuart.schacher@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
MTU setting does not take effect after rte_eth_dev_configure
is called with jumbo enable unless it is configured using the
set_mtu dev_op.
Fixes: daef48efe5 ("net/bnxt: support set MTU")
Cc: stable@dpdk.org
Signed-off-by: Qingmin Liu <qingmin.liu@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Jay Ding <jay.ding@broadcom.com>
Reviewed-by: Randy Schacher <stuart.schacher@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Validate pointers aren't pointing to uninitialized areas
including txq and rxq before using them to avoid
bnxt driver from crashing.
Signed-off-by: Rahul Gupta <rahul.gupta@broadcom.com>
Signed-off-by: Jay Ding <jay.ding@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Randy Schacher <stuart.schacher@broadcom.com>
Tested-by: Randy Schacher <stuart.schacher@broadcom.com>
Return EINVAL instead of ENOSPC when invalid queue_idx passed in
during rx and tx queue_setup_op routines.
Signed-off-by: Jay Ding <jay.ding@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Rename driver version from "Broadcom Cumulus driver" to
"Broadcom NetXtreme driver" to reflect this driver is applicable to
NetXtreme family beyond Cumulus.
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
rename check_zero_bytes to bnxt_check_zero_bytes to match proper prefix.
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Add support to bnxt driver to register RTE_ETH_EVENT_INTR_LSC
event and monitor physical link status.
Signed-off-by: Qingmin Liu <qingmin.liu@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Randy Schacher <stuart.schacher@broadcom.com>
We are still using the txq_flags which is no longer needed with the
new offload API. Cleaning it up.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Contrary to all other pattern items, these are inconsistently documented as
affecting traffic instead of simply matching its origin, without provision
for the latter.
This commit clarifies documentation and updates PMDs since the original
behavior now has to be explicitly requested using the new transfer
attribute.
It breaks ABI compatibility for the following public functions:
- rte_flow_create()
- rte_flow_validate()
Impacted PMDs are bnxt and i40e, for which the VF pattern item is now only
supported when a transfer attribute is also present.
Fixes: b1a4b4cbc0 ("ethdev: introduce generic flow API")
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
This new attribute enables applications to create flow rules that do not
simply match traffic whose origin is specified in the pattern (e.g. some
non-default physical port or VF), but actively affect it by applying the
flow rule at the lowest possible level in the underlying device.
It breaks ABI compatibility for the following public functions:
- rte_flow_copy()
- rte_flow_create()
- rte_flow_validate()
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
TPID handling in rte_flow VLAN and E_TAG pattern item definitions is not
consistent with the normal stacking order of pattern items, which is
confusing to applications.
Problem is that when followed by one of these layers, the EtherType field
of the preceding layer keeps its "inner" definition, and the "outer" TPID
is provided by the subsequent layer, the reverse of how a packet looks like
on the wire:
Wire: [ ETH TPID = A | VLAN EtherType = B | B DATA ]
rte_flow: [ ETH EtherType = B | VLAN TPID = A | B DATA ]
Worse, when QinQ is involved, the stacking order of VLAN layers is
unspecified. It is unclear whether it should be reversed (innermost to
outermost) as well given TPID applies to the previous layer:
Wire: [ ETH TPID = A | VLAN TPID = B | VLAN EtherType = C | C DATA ]
rte_flow 1: [ ETH EtherType = C | VLAN TPID = B | VLAN TPID = A | C DATA ]
rte_flow 2: [ ETH EtherType = C | VLAN TPID = A | VLAN TPID = B | C DATA ]
While specifying EtherType/TPID is hopefully rarely necessary, the stacking
order in case of QinQ and the lack of documentation remain an issue.
This patch replaces TPID in the VLAN pattern item with an inner
EtherType/TPID as is usually done everywhere else (e.g. struct vlan_hdr),
clarifies documentation and updates all relevant code.
It breaks ABI compatibility for the following public functions:
- rte_flow_copy()
- rte_flow_create()
- rte_flow_query()
- rte_flow_validate()
Summary of changes for PMDs that implement ETH, VLAN or E_TAG pattern
items:
- bnxt: EtherType matching is supported with and without VLAN, but TPID
matching is not and triggers an error.
- e1000: EtherType matching is only supported with the ETHERTYPE filter,
which does not support VLAN matching, therefore no impact.
- enic: same as bnxt.
- i40e: same as bnxt with existing FDIR limitations on allowed EtherType
values. The remaining filter types (VXLAN, NVGRE, QINQ) do not support
EtherType matching.
- ixgbe: same as e1000, with additional minor change to rely on the new
E-Tag macro definition.
- mlx4: EtherType/TPID matching is not supported, no impact.
- mlx5: same as bnxt.
- mvpp2: same as bnxt.
- sfc: same as bnxt.
- tap: same as bnxt.
Fixes: b1a4b4cbc0 ("ethdev: introduce generic flow API")
Fixes: 99e7003831 ("net/ixgbe: parse L2 tunnel filter")
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Acked-by: Andrew Rybchenko <arybchenko@solarflare.com>
Initialize mbuf->data_off to RTE_PKTMBUF_HEADROOM after allocation.
Without this, it might be possible that the DMA address provided
to the HW may not be in sync to what is indicated to the application
in bnxt_rx_pkt.
Fixes: 2eb53b134a ("net/bnxt: add initial Rx code")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
In some cases bnxt_hwrm_cfa_l2_set_rx_mask is being called before
VNICs are allocated. The FW returns an error in such cases.
Move bnxt_init_nic to bnxt_dev_init such that the ids are initialized
to an invalid id.
Prevent sending the command to the FW only with a valid vnic id.
Fixes: 244bc98b0d ("net/bnxt: set L2 Rx mask")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
While creating TX, Rx, CQ rings use cached DB address instead of
getting it from the PCI memory resource.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Some values are interpreted without endian conversion and/or without
taking the proper mask into account.
Fixes: 5ef3b79fdf ("net/bnxt: support flow filter ops")
Cc: stable@dpdk.org
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
Since we are storing the mem_zone address for each ring created,
we are freeing the same address multiple times.
For example the memory zone created for Rx is being freed during
Rx ring cleanup, AGG ring cleanup and CQ cleanup.
Avoid this by storing the memory zone address in RXQ instead and
free it as a part of queue_release dev_op.
In the same way do the same for TX queues as well.
Fixes: 51c87ebafc ("net/bnxt: add Tx queue create/destroy")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Memory allocated to hold VF filter info is not being freed currently.
This can cause potential memory leak.
Fixes: 7a5b087444 ("net/bnxt: support to add a VF MAC address")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
The fw_l2_filter_id for a ntuple filter is needed only for the lifetime
of the ntuple filter. Once the filter is free, reset the field.
The associated l2_filter will be freed as a part of its own cleanup.
Fixes: 5ef3b79fdf ("net/bnxt: support flow filter ops")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
The hwrm_queue_qportcfg command has been extended to determine
the COS queue that a Tx ring needs to use. This patch adds code
to determine the information from the FW and use it while
creating the Tx rings.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
bnxt_hwrm_clear_l2_filter needs to be called only if the filter type
is L2 and not otherwise.
Also check for the return value of bnxt_hwrm_clear_l2_filter().
Fixes: 5ef3b79fdf ("net/bnxt: support flow filter ops")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
We are wrongly freeing up a filter in the driver while it is still
configured in the HW. This can cause incorrect L2 filter id to be
used for filters created subsequently.
This filter will be cleared on cleanup anyway.
Fixes: 5ef3b79fdf ("net/bnxt: support flow filter ops")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Fix Rx checksum status for tunnel frames as seen by hardware.
Current code does not handle cases for tunnel frames correctly.
Fixes: 7ec39d8c52 ("net/bnxt: update status of Rx IP/L4 CKSUM")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
We are wrongly setting the Rx path flag while creating the ntuple filter.
It needs to be set for L2 or Exact Match filters only.
Fixes: 5ef3b79fdf ("net/bnxt: support flow filter ops")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>