params->leaf.cman has enum type which is not isomorphic with boolean
type, however it is used as a boolean expression.
This patch fixed it.
Fixes: c09c7847d8 ("net/hns3: support traffic management")
Cc: stable@dpdk.org
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
'HNS3_RXD_LKBK_B' was defined in previous versions but no used.
This patch deleted it.
Fixes: bba6366983 ("net/hns3: support Rx/Tx and related operations")
Cc: stable@dpdk.org
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
The recvfrom() syscall is only supported by AF_XDP sockets since
kernel 5.11. Only use it if busy polling is configured. We can
assume a kernel >= 5.11 is in use if busy polling is configured
so we can safely call recvfrom() in that case.
Fixes: 63e8989fe5 ("net/af_xdp: use recvfrom instead of poll syscall")
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
The send() syscall on the Tx path is not concerned with busy polling
and as such its invocation should not depend on whether or not it is
configured. Fix this by distinguishing the conditions necessary for
syscalls on the Rx and Tx paths individually.
Fixes: 055a393626 ("net/af_xdp: prefer busy polling")
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
When DEV_RX_OFFLOAD_KEEP_CRC is enabled, the PMD will minus 4 bytes
of CRC from the size of a packet, but the NIC will strip the CRC
because the CRC strip bit in DVMOLR register is not cleared. This
will cause the size of a packet to be 4 bytes less.
This patch updates the CRC strip bit according to whether
DEV_RX_OFFLOAD_KEEP_CRC is enabled.
Fixes: a5aeb2b9e2 ("net/igc: support Rx and Tx")
Cc: stable@dpdk.org
Signed-off-by: Alvin Zhang <alvinx.zhang@intel.com>
Acked-by: Haiyue Wang <haiyue.wang@intel.com>
Driver cancels the health check alarm only if error recovery is enabled
in the FW. This can cause an issue. There is a small window where the
driver receives the async event from FW and port close is invoked
immediately. Driver clears BNXT_FLAG_RECOVERY_ENABLED flag when it gets
the async event from FW. As a result, the health check alarm will not
get canceled during port close and causes a segfault when the alarm tries
to read Heartbeat register.
Fix this by canceling the health check alarm unconditionally during
port stop.
Fixes: 9d0cbaecc9 ("net/bnxt: support periodic FW health monitoring")
Cc: stable@dpdk.org
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
For Thor devices, RSS table can only accommodate 512 Rx queues.
When RSS is enabled, Cap the max Rx rings to 512.
For non-RSS case, the number will be limited by number of VNICs.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Lance Richardson <lance.richardson@broadcom.com>
Fix resource cleanup in port close.
Once the pointers are freed, set them to NULL.
Make sure access to the pointers is validated before use.
Fixes: bb81e07323 ("net/bnxt: support LED on/off")
Fixes: 804e746c7b ("net/bnxt: add hardware resource manager init code")
Fixes: 1d0704f4d7 ("net/bnxt: add device configure operation")
Fixes: 698aa7e953 ("net/bnxt: add code to determine the Tx COS queue")
Fixes: 322bd6e702 ("net/bnxt: add port representor infrastructure")
Fixes: 0bf5a0b5eb ("net/bnxt: add a failure log")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Adding the bond device as its own slave should be forbidden. This
will cause a recursive endless loop in many subsequent operations,
and eventually lead to coredump.
This problem was found in testpmd, the related logs are as follows:
testpmd> create bonded device 1 0
Created new bonded device net_bonding_testpmd_0 on (port 4).
testpmd> add bonding slave 4 4
Segmentation fault (core dumped)
The call stack is as follows:
0x000000000064eb90 in rte_eth_dev_info_get ()
0x00000000006df4b4 in bond_ethdev_info ()
0x000000000064eb90 in rte_eth_dev_info_get ()
0x00000000006df4b4 in bond_ethdev_info ()
0x000000000064eb90 in rte_eth_dev_info_get ()
0x0000000000564e58 in eth_dev_info_get_print_err ()
0x000000000055e8a4 in init_port_config ()
0x000000000052730c in cmd_add_bonding_slave_parsed ()
0x0000000000646f60 in cmdline_parse ()
0x0000000000645e08 in cmdline_valid_buffer ()
0x000000000064956c in rdline_char_in ()
0x0000000000645ee0 in cmdline_in ()
0x00000000006460a4 in cmdline_interact ()
0x0000000000531904 in prompt ()
0x000000000051cca8 in main ()
Fixes: 2efb58cbab ("bond: new link bonding library")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
This patch moves the check for "link_speeds" in dev_conf to
dev_configure, so that users know whether "link_speeds" is valid in
advance.
Fixes: bdaf190f82 ("net/hns3: support link speed autoneg for PF")
Fixes: 400d307e1a ("net/hns3: support fixed link speed")
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, the fdir lock was used to protect concurrent access in
multiple processes, it has the following problems:
1) Lack of protection for fdir reset recover.
2) Only part of data is protected, eg. the filterlist is not protected.
We use the following scheme:
1) Del the fdir lock.
2) Add a flow lock and provides rte flow driver ops API-level
protection.
3) Declare support RTE_ETH_DEV_FLOW_OPS_THREAD_SAFE.
Fixes: fcba820d9b ("net/hns3: support flow director")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
HNS3 PF driver only supports RSS, DCB or NONE multiple queues mode.
Currently, driver doesn't verify the VMDq multi-queue mode completely.
This patch fixes the verification for VMDq mode.
Fixes: 62e3ccc2b9 ("net/hns3: support flow control")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, "ONLY DCB" and "DCB+RSS" mode are both supported by HNS3
PF driver. But the driver verifies only the "DCB+RSS" multiple queues
mode.
Fixes: 62e3ccc2b9 ("net/hns3: support flow control")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Some mbx messages do not need to reply with data. In this case,
it is no need to set the response data address and the response
length.
This patch removes these redundant codes from mbx messages that do
not need be replied.
Fixes: a5475d61fa ("net/hns3: support VF")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Rx vector implementation depends on the mbuf fields
(such as rearm_data/rx_descriptor_fields1) layout, this patch adds
compile-time verification for this.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
The i40evf PMD will be deprecated, iavf will be the only VF driver for
Intel 700 serial (i40e) NIC family.
To reach this, there will be 2 steps:
Step 1: iavf will be the default VF driver, while i40evf still can be
selected by devarg: "driver=i40evf".
This is covered by this patch, which include:
1) add all 700 serial NIC VF device ID into iavf PMD
2) skip probe if devargs contain "driver=i40evf" in iavf
3) continue probe if devargs contain "driver=i40evf" in i40evf
Step 2: i40evf and related devarg are removed, this will happen at DPDK
21.11
Between step 1 and step 2, no new feature will be added into i40evf
except bug fix.
Signed-off-by: Robin Zhang <robinx.zhang@intel.com>
Acked-by: Qi Zhang <qi.z.zhang@intel.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Beilei Xing <beilei.xing@intel.com>
Due to hardware limitations the VLAN push/pop and decap actions following
the sample action are supported in the FDB Tx steering domain only, the
flows with incorrect action order for other domains are rejected by
rdma-core.
To provide the action order requested in flow API this patch checks for
the VLAN or decap precedence to the sample action and moves the VLAN or
decap actions into the next flow in the new table and adds the jump
action in the prefix sample flow.
This patch also adds the validation for these combination actions.
Fixes: 255b8f86eb ("net/mlx5: fix E-Switch egress mirror flow validation")
Cc: stable@dpdk.org
Signed-off-by: Jiawei Wang <jiaweiw@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Modify API mlx5_flow_dev_dump to support the feature.
Modify mlx5_socket since one extra arg flow_ptr is added.
The data structure sent to DPDK application from the utility triggering
the flow dumps should be packed and endianness must be specified.
The native host endianness can be used, all exchange happens within
the same host (we use sendmsg aux data and share the file handle,
remote approach is not applicable, no inter-host communication happens).
The message structure to dump one/all flow(s):
struct mlx5_flow_dump_req {
uint32_t port_id;
uint64_t flow_ptr;
} __rte_packed;
If flow_ptr is 0, all flows for the specified port will be dumped.
Signed-off-by: Haifei Luo <haifeil@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
This patch supports check max SIMD bitwidth when choosing NEON and SVE
vector path.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, the L3L4P/L3E/L4E/OL3E/OL4E fields in Rx descriptor used to
indicate hardware checksum result:
1. L3L4P: indicates hardware has processed L3L4 checksum for this
packet, if this bit is 1 then L3E/L4E/OL3E/OL4E is trustable.
2. L3E: L3 checksum error indication, 1 means with error.
3. L4E: L4 checksum error indication, 1 means with error.
4. OL3E: outer L3 checksum error indication, 1 means with error.
5. OL4E: outer L4 checksum error indication, 1 means with error.
Driver will set the good checksum flag through packet type and
L3E/L4E/OL3E/OL4E when L3L4P is 1, it runs as follows:
1. If packet type indicates it's tunnel packet:
1.1. If packet type indicates it has inner L3 and L3E is zero, then
mark the IP checksum good.
1.2. If packet type indicates it has inner L4 and L4E is zero, then
mark the L4 checksum good.
1.3. If packet type indicates it has outer L4 and OL4E is zero, then
mark the outer L4 checksum good.
2. If packet type indicates it's not tunnel packet:
2.1. If packet type indicates it has L3 and L3E is zero, then mark the
IP checksum good.
2.2. If packet type indicates it has L4 and L4E is zero, then mark the
L4 checksum good.
As described above, the good checksum calculation is time consuming,
it impacts the Rx performance.
By balancing performance and functionality, driver uses the following
scheme to set good checksum flag when L3L4P is 1:
1. If L3E is zero, then mark the IP checksum good.
2. If L4E is zero, then mark the L4 checksum good.
The performance gains are 3% in small packet iofwd scenarios.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
This patch supports runtime config of mask device capability, it was
used to mask the capability which queried from firmware.
The device argument key is "dev_caps_mask" which takes hexadecimal
bitmask where each bit represents whether mask corresponding capability.
Its main purpose is to debug and avoid problems.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Right now, rte_flow_shared_action_* APIs are used for some shared
actions, like RSS, count. The shared action should be created before
using it inside a flow. These shared actions sometimes are not
really shared but just some indirect actions decoupled from a flow.
The new functions rte_flow_action_handle_* are added to replace
the current shared functions rte_flow_shared_action_*.
There are two types of flow actions:
1. the direct (normal) actions that could be created and stored
within a flow rule. Such action is tied to its flow rule and
cannot be reused.
2. the indirect action, in the past, named shared_action. It is
created from a direct actioni, like count or rss, and then used
in the flow rules with an object handle. The PMD will take care
of the retrieve from indirect action to the direct action
when it is referenced.
The indirect action is accessed (update / query) w/o any flow rule,
just via the action object handle. For example, when querying or
resetting a counter, it could be done out of any flow using this
counter, but only the handle of the counter action object is
required.
The indirect action object could be shared by different flows or
used by a single flow, depending on the direct action type and
the real-life requirements.
The handle of an indirect action object is opaque and defined in
each driver and possibly different per direct action type.
The old name "shared" is improper in a sense and should be replaced.
Since the APIs are changed from "rte_flow_shared_action*" to the new
"rte_flow_action_handle*", the testpmd application code and command
line interfaces also need to be updated to do the adaption.
The testpmd application user guide is also updated. All the "shared
action" related parts are replaced with "indirect action" to have a
correct explanation.
The parameter of "update" interface is also changed. A general
pointer will replace the rte_flow_action struct pointer due to the
facts:
1. Some action may not support fields updating. In the example of a
counter, the only "update" supported should be the reset. So
passing a rte_flow_action struct pointer is meaningless and
there is even no such corresponding action struct. What's more,
if more than one operations should be supported, for some other
action, such pointer parameter may not meet the need.
2. Some action may need conditional or partial update, the current
parameter will not provide the ability to indicate which part(s)
to update.
For different types of indirect action objects, the pointer could
either be the same of rte_flow_action* struct - in order not to
break the current driver implementation, or some wrapper
structures with bits as masks to indicate which part to be
updated, depending on real needs of the corresponding direct
action. For different direct actions, the structures of indirect
action objects updating will be different.
All the underlayer PMD callbacks will be moved to these new APIs.
The RTE_FLOW_ACTION_TYPE_SHARED is kept for now in order not to
break the ABI. All the implementations are changed by using
RTE_FLOW_ACTION_TYPE_INDIRECT.
Since the APIs are changed from "rte_flow_shared_action*" to the new
"rte_flow_action_handle*" and the "update" interface's 3rd input
parameter is changed to generic pointer, the mlx5 PMD that uses these
APIs needs to do the adaption to the new APIs as well.
Signed-off-by: Bing Zhao <bingz@nvidia.com>
Acked-by: Andrey Vesnovaty <andreyv@nvidia.com>
Acked-by: Ori Kam <orika@nvidia.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Kunpeng 930 uses a new RAS exception reporting solution.
The reset type and exception status are reported through
firmware. The driver modifies the corresponding code to
adapt to the new solution.
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
'HNS3_RXD_TSIND_S' and 'HNS3_RXD_TSIND_M' is unused, which should
be deleted.
This patch fixed it.
Fixes: bba6366983 ("net/hns3: support Rx/Tx and related operations")
Cc: stable@dpdk.org
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
This patch supports set VSI reset thread name which is helpful for
debugging.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
This patch supports set delay packet generator start thread name which
is helpful for debugging.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Ensure all lists of drivers are standardized:
* one driver per line
* lists double-indented with spaces (as they are line continuations)
* elements in alphabetical order
* opening and closing list brackets "[" & "]" on own lines
* last element has trailing comma
Any code snippets in the list files is adjusted to single-indent using
whitespace to correspond to the new style also.
The lists of standard library dependencies per class, and other short
lists are not formatted one-per-line as these lists are not expected to
grow beyond 2 or 3 entries.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Split AVX512 Rx data path into two, one is for basic,
the other one can support additional Rx offload features,
including Rx checksum offload, Rx vlan offload, RSS offload.
Signed-off-by: Leyi Rong <leyi.rong@intel.com>
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Tested-by: Qin Sun <qinx.sun@intel.com>
Add alternative Tx data path for AVX512 which can support partial
Tx offload features, including Tx checksum offload, vlan/QinQ
insertion offload.
Signed-off-by: Leyi Rong <leyi.rong@intel.com>
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Tested-by: Qin Sun <qinx.sun@intel.com>
When set default MAC address, use type VIRTCHNL_ETHER_ADDR_PRIMARY as this
case is changing device/primary unicast MAC. For other cases, such as
adding or deleting extra unicast addresses and multicast addresses, use
type VIRTCHNL_ETHER_ADDR_EXTRA.
Fixes: cb25d4323f ("net/avf: enable MAC VLAN and promisc ops")
Cc: stable@dpdk.org
Signed-off-by: Robin Zhang <robinx.zhang@intel.com>
Tested-by: Yan Xia <yanx.xia@intel.com>
Currently, there is no way for a VF driver to specify that it wants to
change its device/primary unicast MAC address. This makes it
difficult/impossible for the PF driver to track the VF's device/primary
unicast MAC address, which is used for VM/VF reboot and displaying on
the host. Fix this by using 2 bits of a pad byte in the
virtchnl_ether_addr structure so the VF can specify what type of MAC
it's adding/deleting.
Below are the values that should be used by all VF drivers going
forward.
VIRTCHNL_ETHER_ADDR_LEGACY(0):
- The type should only ever be 0 for legacy AVF drivers (i.e.
drivers that don't support the new type bits). The PF drivers
will track VF's device/primary unicast MAC using with best
effort.
VIRTCHNL_ETHER_ADDR_PRIMARY(1):
- This type should only be used when the VF is changing their
device/primary unicast MAC. It should be used for both delete
and add cases related to the device/primary unicast MAC.
VIRTCHNL_ETHER_ADDR_EXTRA(2):
- This type should be used when the VF is adding and/or deleting
MAC addresses that are not the device/primary unicast MAC. For
example, extra unicast addresses and multicast addresses
assuming the PF supports "extra" addresses at all.
If a PF is parsing the type field of the virtchnl_ether_addr, then it
should use the VIRTCHNL_ETHER_ADDR_TYPE_MASK to mask the first two bits
of the type field since 0, 1, and 2 are the only valid values.
For i40evf PMD, when set default MAC address, use type
VIRTCHNL_ETHER_ADDR_PRIMARY as this case is changing device/primary
unicast MAC. For other cases, such as adding or deleting extra unicast
addresses and multicast addresses, use type VIRTCHNL_ETHER_ADDR_EXTRA.
Fixes: 6d13ea8e8e ("net: add rte prefix to ether structures")
Fixes: caccf8b318 ("ethdev: return diagnostic when setting MAC address")
Cc: stable@dpdk.org
Signed-off-by: Robin Zhang <robinx.zhang@intel.com>
Tested-by: Yan Xia <yanx.xia@intel.com>
Support rte flow priority attribute for DCF switch filter.
When a packet is matched by two rules, the behavior of it
is not defined. This patch supports flow priority to create
different recipes for this situation. Only priority 0 and 1
are supported and higher value denotes higher priority.
for example:
1. flow create 0 priority 0 ingress pattern eth / vlan tci is 2 / vlan
tci is 2 / end actions vf id 2 / end
2. flow create 0 priority 1 ingress pattern eth / vlan / vlan / ipv4 dst
is 192.168.0.1 / end actions vf id 1 / end
These two rules can be created at the same time in DCF switch
filter and priority of rule 2 is higher. Packet hits rule 2
when two conditions of rules are satisfied.
Signed-off-by: Yuying Zhang <yuying.zhang@intel.com>
Acked-by: Qi Zhang <qi.z.zhang@intel.com>
Enable additional PHY types (25G-AOC and 25G-ACC) for set PHY config
command.
Signed-off-by: Yury Kylulin <yury.kylulin@intel.com>
Tested-by: Ashish Paul <apaul@juniper.net>
This patch separates Tx burst function implementations to different
source files, thus allowing them to compile in parallel.
Signed-off-by: Michael Baum <michaelba@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
This patch separates Tx function implementations to different source
file as an optional preparation step for Tx cleanup.
Signed-off-by: Michael Baum <michaelba@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
This patch moves Tx burst and its inline functions declarations to
header file to allow its use from several separate source files and as a
possible preparation for Tx cleanup.
Signed-off-by: Michael Baum <michaelba@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
This patch separates Tx function declarations to different header file
in preparation for removing their implementation from the source file
and as an optional preparation for Tx cleanup.
Signed-off-by: Michael Baum <michaelba@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
This patch separates Rx function implementations to different source
file as an optional preparation step for further consolidation of Rx
burst functions.
Signed-off-by: Michael Baum <michaelba@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
The mlx5_rxtx.c file contains a lot of Tx burst functions, each of those
is performance-optimized for the specific set of requested offloads.
These ones are generated on the basis of the template function and it
takes significant time to compile, just due to a large number of giant
functions generated in the same file and this compilation is not being
done in parallel with using multithreading.
Therefore we can split the mlx5_rxtx.c file into several separate files
to allow different functions to be compiled simultaneously.
In this patch, we separate Rx function declarations to different header
file in preparation for removing them from the source file and as an
optional preparation step for further consolidation of Rx burst
functions.
Signed-off-by: Michael Baum <michaelba@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Currently, user could use runtime config "rx_func_hint=simple" to
select the hns3_recv_pkts API, but the API's name get from
rte_eth_rx_burst_mode_get is "Scalar" which has not reflected "simple".
So this patch renames hns3_recv_pkts to hns3_recv_pkts_simple, and
also change it's name which gets from rte_eth_rx_burst_mode_get to
"Scalar Simple" to maintain conceptual consistency.
Fixes: 521ab3e933 ("net/hns3: add simple Rx path")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
Restore the original code, where VHOST_SET_OWNER is applied to
all vhostfds of the device.
Fixes: 06856cabb8 ("net/virtio: add virtio-user ops to set owner")
Cc: stable@dpdk.org
Signed-off-by: Thierry Herbelot <thierry.herbelot@6wind.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
This patch adds the configuration of fixed speed for the PF device.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
If the flow control auto-negotiation is not supported and the flow
control modes on the local and link partner is asymmetric, the flow
control on the NIC does not take effect. The support of the
auto-negotiation capability requires the cooperation of the firmware
and driver.
This patch supports the flow control auto-negotiation only for copper
port. For optical ports, the forced flow control mode is still used.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
This patch supports link speed auto-negotiation for PF. If the
device supports auto-negotiation, the device negotiates with
the link partner at all speeds supported by the device.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
The speed capability of the device can be reported to the upper-layer app
in rte_eth_dev_info_get API. In this API, the speed capability is derived
from the 'supported_speed', which is the speed capability actually
supported by the NIC. The value of the 'supported_speed' is obtained
once in the probe stage and may be updated in the scheduled task to deal
with the change of the transmission interface.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, the speed of fiber port is obtained by using the default
query type of HNS3_OPC_GET_SFP_INFO opcode. In this way, only
the speed of the optical module can be obtained. In fact, the opcode
also supports an active query type, which is a channel for obtaining
information such as the speed, the supported speed, auto-negotiation
capability, and FEC mode. This patch changes the query type of the
opcode from the default query type to the active query type to obtain
the supported speed of fiber port.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
The firmware compatibility configuration in PF driver is used to
maintain the compatibility of some features of the driver and
firmware, and requires firmware to enable these features. Currently,
the configuration is in hns3_init_hardware(), which is a little back.
Because firmware may clear some configurations (such as, MAC related)
after receiving the command. And firmware can not be aware of some
default initializations (such as, flow control) before executing the
command to set the copper PHY when the PHY is controlled by firmware.
Therefore, it is recommended that no other hardware resources are
configured before the compatibility configuration. And it should be
moved to hns3_cmd_init(), which is responsible for the firmware
command initialization of driver.
In addition, the driver needs to perform corresponding processing
if the command fails to be sent.
1) If firmware fails to take over the copper PHY, the copper port fails
to initialize.
2) If fails to enable the report of link events, the device does not
support the LSC capability.
Fixes: bff6ebfe30d4 ("net/hns3: refactor PF LSC event report")
Fixes: bac6a06441 ("net/hns3: fix link status change from firmware")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, hns3 driver doesn't support to flow control auto-negotiation.
The FC mode requested by user is the same as the current FC mode. It is
not necessary to maintain the current FC mode. We only report the current
FC mode based on actual flow control mode in hns3_flow_ctrl_get().
This patch removes this redundant field. In addition, "requested_mode" in
hns3_hw struct indicates the FC mode requested by user, and the name is
unreasonable. It needs to be modified to "requested_fc_mode".
Fixes: 62e3ccc2b9 ("net/hns3: support flow control")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
The bit(5) of supported, advertising and lp_advertising for copper
PHYs obtained from the firmware indicates 1000M full-duplex. This
speed capability bit is missing in the current codes.
Fixes: 2e4859f3b3 ("net/hns3: support PF device with copper PHYs")
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
The "supported capability" obtained from firmware on copper ports
includes the speed capability, auto-negotiation capability, and flow
control capability. Therefore, this patch changes "supported_capa" to
"supported_speed" and parses the speed capability supported by the
driver from the "supported capability".
Fixes: 2e4859f3b3 ("net/hns3: support PF device with copper PHYs")
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
In the previous patch, driver will calculate packet type by ignoring
VLAN information because the packet type may calculate error when
exist VLAN and VLAN strip.
So here remove the following ptypes from support list:
1) RTE_PTYPE_L2_ETHER_VLAN
2) RTE_PTYPE_L2_ETHER_QINQ
3) RTE_PTYPE_INNER_L2_ETHER_VLAN
4) RTE_PTYPE_INNER_L2_ETHER_QINQ
Fixes: bba6366983 ("net/hns3: support Rx/Tx and related operations")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Kunpeng 930 supports RXD advanced layout. If enabled the layout, the
hardware will report packet type by 8-bit PTYPE filed in the Rx
descriptor, and the supported ptypes are different from original
scheme. So this patch adds supported list for RXD advanced layout.
Fixes: fb5e906940 ("net/hns3: support Rx descriptor advanced layout")
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
The PTP depends on special packet type reported by hardware which
enabled rxd advanced layout, so if the hardware doesn't support rxd
advanced layout, driver should ignore the PTP capability.
Fixes: 4387523581 ("net/hns3: get device capability from firmware")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
This patch supports reporting TUNNEL GRE packet type when rxd advanced
layout enabled.
Fixes: fb5e906940 ("net/hns3: support Rx descriptor advanced layout")
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
This patch adds RTE_PTYPE_L4_UDP flag when parsed tunnel vxlan packet.
Fixes: bba6366983 ("net/hns3: support Rx/Tx and related operations")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
The type of return value of hns3_cmd_send is int, some function declare
the return value as hns3_cmd_status.
This patch fix the incorrect use of the enum hns3_cmd_status.
Fixes: 737f30e1c3 ("net/hns3: support command interface with firmware")
Fixes: 02a7b55657 ("net/hns3: support Rx interrupt")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, when processing MBX messages, the system timestamp is obtained
to determine whether timeout occurs. However, the gettimeofday function
is not monotonically increasing. Therefore, this may lead to incorrect
judgment or difficulty exiting the loop. And actually, in this scenario,
it is not necessary to obtain the timestamp.
This patch deletes the call to the gettimeofday function during MBX
message processing.
Fixes: 463e748964 ("net/hns3: support mailbox")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
VF will build two queues (csq: command send queue, crq: command receive
queue) with firmware, the crq may contain the following messages:
1) mailbox response message which was the ack of mailbox sync request.
2) PF's link status change message which may send by PF at anytime;
Currently, any threads in the primary and secondary processes could
send mailbox sync request, so it will need to process the crq messages
in there own thread context.
If the crq hold two messages: a) PF's link status change message, b)
mailbox response message when secondary process deals with the crq
messages, it will lead to report lsc event in secondary process
because it uses the policy of processing all pending messages at once.
We use the following scheme to solve it:
1) threads in secondary process could only process specifics messages
(eg. mailbox response message) in crq, if the message processed, its
opcode will rewrite with zero, then the intr thread in primary
process will not process again.
2) threads other than intr thread in the primary process use the same
processing logic as the threads in secondary process.
3) intr thread in the primary process could process all messages.
Fixes: 76a3836b98 ("net/hns3: fix setting default MAC address in bonding of VF")
Fixes: 463e748964 ("net/hns3: support mailbox")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, the mailbox synchronous communication between VF and PF use
the following fields to maintain communication:
1. Req_msg_data which was combined by message code and subcode, used to
match request and response.
2. Head which means the number of requests successfully sent by VF.
3. Tail which means the number of responses successfully received by VF.
4. Lost which means the number of requests which are timeout.
There may possible mismatches of the following situation:
1. VF sends message A with code=1 subcode=1.
Then head=1, tail=0, lost=0.
2. PF was blocked about 500ms when processing the message A.
3. VF will detect message A timeout because it can't get the response
within 500ms.
Then head=1, tail=0, lost=1.
4. VF sends message B with code=1 subcode=1 which equal message A.
Then head=2, tail=0, lost=1.
5. PF processes the first message A and send the response message to VF.
6. VF will update tail field to 1, but the lost field will remain
unchanged because the code/subcode equal message B's, so driver will
return success because now the head(2) equals tail(1) plus lost(1).
This will lead to mismatch of request and response.
To fix the above bug, we use the following scheme:
1. The message sent from VF was labelled with match_id which was a
unique 16-bit non-zero value.
2. The response sent from PF will label with match_id which got from the
request.
3. The VF uses the match_id to match request and response message.
This scheme depends on the PF driver, if the PF driver don't support
then VF will uses the original scheme.
Fixes: 463e748964 ("net/hns3: support mailbox")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, driver will copy mailbox messages body into arq ring when
process HNS3_MBX_LINK_STAT_CHANGE and HNS3_MBX_LINK_STAT_CHANGE
message, and then call hns3_mbx_handler API which will direct process
pre-copy messages. In the whole process, the arq ring don't have a
substantial effect.
Note: The arq ring is designed for kernel environment which could not
do much job in interrupt context, but for DPDK it's not required.
Also we rename hns3_handle_link_change_event to
hns3pf_handle_link_change_event which add 'pf' suffix to make it
better to distinguish.
Fixes: 463e748964 ("net/hns3: support mailbox")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Add a specific path for RX AVX512 (flexible descriptor).
In this path, support the HW offload features, like,
checksum, VLAN stripping, RSS hash.
This path is chosen automatically according to the
configuration.
'inline' is used, then the duplicate code is generated
by the compiler.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Qi Zhang <qi.z.zhang@intel.com>
Add a specific path for RX AVX512 (traditional).
In this path, support the HW offload features, like,
checksum, VLAN stripping, RSS hash.
This path is chosen automatically according to the
configuration.
'inline' is used, then the duplicate code is generated
by the compiler.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Qi Zhang <qi.z.zhang@intel.com>
Add a specific path for TX AVX512.
In this path, support the HW offload features, like,
checksum insertion, VLAN insertion.
This path is chosen automatically according to the
configuration.
'inline' is used, then the duplicate code is generated
by the compiler.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Qi Zhang <qi.z.zhang@intel.com>
Add the offload flag for RX queues to know which offload
features are set.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Qi Zhang <qi.z.zhang@intel.com>
Fix segment fault when failing to get the memory from the pool.
If there's no memory in the default cache, fall back to the
previous process.
The previous AVX2 rearm function is changed to add some AVX512
instructions and changed to a callee of the AVX2 and AVX512
rearm functions.
Fixes: e6a6a13891 ("net/i40e: add AVX512 vector path")
Cc: stable@dpdk.org
Reported-by: David Coyle <david.coyle@intel.com>
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Tested-by: David Coyle <david.coyle@intel.com>
Fix segment fault when failing to get the memory from the pool.
If there's no memory in the default cache, fall back to the
previous process.
The previous AVX2 rearm function is changed to add some AVX512
instructions and changed to a callee of the AVX2 and AVX512
rearm functions.
Fixes: 7f85d5ebcf ("net/ice: add AVX512 vector path")
Cc: stable@dpdk.org
Reported-by: David Coyle <david.coyle@intel.com>
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Tested-by: David Coyle <david.coyle@intel.com>
Fix segment fault when failing to get the memory from the pool.
If there's no memory in the default cache, fall back to the
previous process.
The previous AVX2 rearm function is changed to add some AVX512
instructions and changed to a callee of the AVX2 and AVX512
rearm functions.
Fixes: 31737f2b66 ("net/iavf: enable AVX512 for legacy Rx")
Cc: stable@dpdk.org
Reported-by: David Coyle <david.coyle@intel.com>
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Tested-by: David Coyle <david.coyle@intel.com>
Previous implementations support dump all the flows. Add new arg
rte_flow in rte_flow_dev_dump to dump one flow.
Signed-off-by: Haifei Luo <haifeil@nvidia.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Ori Kam <orika@nvidia.com>
These headers are used but not included explicitly, including them.
"arpa/inet.h" is included for 'htons' and friends.
"netinet/in.h" is included for 'IPPROTO_IP'.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Acked-by: Rasesh Mody <rmody@marvell.com>
Currently meter algorithms only supports bytes per second(BPS).
Check packet_mode set to TRUE are rejected.
Signed-off-by: Li Zhang <lizh@nvidia.com>
Acked-by: Matan Azrad <matan@nvidia.com>
Acked-by: Liron Himi <lironh@marvell.com>
Currently meter algorithms only supports bytes per second(BPS).
Check packet_mode set to TRUE are rejected.
Signed-off-by: Li Zhang <lizh@nvidia.com>
Acked-by: Matan Azrad <matan@nvidia.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
The hardware outer/inner VLAN protocol types are now updated to map to
new interface VLAN protocol types, so update the application to use new
VLAN protocol types when the rte_flow is QinQ filter type.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Acked-by: Qi Zhang <qi.z.zhang@intel.com>
Adds a support for switch filter: GTP-U using just inner fields.
If user doesn't specify outer protocol and its fields but wants to
add switch filter for GTP-U using inner protocols and related fields
such as inner L3 and/or inner L4, this patch enables such filtering.
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Acked-by: Qiming Yang <qiming.yang@intel.com>
Add some new macros of PTYPE values to support PPPoL2TPv2oUDP.
Signed-off-by: Ting Xu <ting.xu@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Acked-by: Qiming Yang <qiming.yang@intel.com>
The dummy packet should be QinQ PPPoE ipv6 when ppp protocol is ipv6.
Fixes: bb3386f348 ("net/ice: enable QinQ filter for switch")
Cc: stable@dpdk.org
Signed-off-by: Yuying Zhang <yuying.zhang@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Acked-by: Qiming Yang <qiming.yang@intel.com>
Since VLAN protocol type 'ICE_VLAN_OFOS' has been changed to map
the hardware VLAN protocol ID to 'ICE_VLAN_OF_HW (16)' when in Double
VLAN mode, and to 'ICE_VLAN_OL_HW (17)' when in Single VLAN mode.
So 'ICE_VLAN_OFOS' can't be used with 'ICE_VLAN_EX' which is outer VLAN
hardware protocol ID 'ICE_VLAN_OF_HW (16)' to do the QinQ VLAN pattern.
Introduce the new inner VLAN protocol type 'ICE_VLAN_IN', which is inner
VLAN hardware protocol ID 'ICE_VLAN_OL_HW (17)'.
Now for QinQ VLAN pattern, the protocol 'ICE_VLAN_EX' and 'ICE_VLAN_IN'
should be used to set the related protocol header fields like VLAN ID.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Acked-by: Qiming Yang <qiming.yang@intel.com>
Add helper functions to set the GPIO pin state or get the value of a
GPIO signal that's the part of the topology based on AQ commands.
This change is needed to setup GPIO pins state for PTP, SyncE etc.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Acked-by: Qiming Yang <qiming.yang@intel.com>
Enable I2C read/write AQ commands. They are now required for
controlling the external physical connectors via external I2C
port expander on E810-T adapters.
Signed-off-by: Maciej Machnikowski <maciej.machnikowski@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Acked-by: Qiming Yang <qiming.yang@intel.com>
Check priority when look for a recipe which matches our request
to enable flow priority for switch filter.
Signed-off-by: Yuying Zhang <yuying.zhang@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Acked-by: Qiming Yang <qiming.yang@intel.com>
Protocol id for first vlan in Double VLAN Mode (DVM) should be
ICE_VLAN_OF_HW = 16, but for Single VLAN Mode (SVM) this should be
ICE_VLAN_OL_HW = 17.
Change protocol id in type to id translation array for outer vlan
to 17 when DVM is enabled, which means the driver, package,
and firmware support DVM.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Acked-by: Qiming Yang <qiming.yang@intel.com>
Add support for PPPoL2TPv2oUDP RSS hash. L2TPv2 and PPP ptypes
and flow headers are added. Protocol id for PPP is added.
Signed-off-by: Ting Xu <ting.xu@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Acked-by: Qiming Yang <qiming.yang@intel.com>
Set E823C device's MAC type as generic.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Acked-by: Qiming Yang <qiming.yang@intel.com>
Remove the unused ptype entry, and use the gcc extension for
ranged initializers in arrays for Linux, and explicitly target
each table entry by index when initializing under Linux.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Acked-by: Qiming Yang <qiming.yang@intel.com>
Adding a function ice_flow_rem_vsi_prof() to remove flow entries
associated to the SW VSI handle. Once complete, clear the vsi index from
the flow profile bitmap. This will ensure that a VSI once removed
can be re-added and the package block rules will be added again.
Signed-off-by: Vignesh Sridhar <vignesh.sridhar@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Acked-by: Qiming Yang <qiming.yang@intel.com>
1. There are a lots of function header mismatch its function name.
2. remove unnecessary header file include.
3. remove unnecessary macro.
4. remove unnecessary comment.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Acked-by: Qiming Yang <qiming.yang@intel.com>
Performance improvement: use a write combining store
instead of a regular mmio write to update queue tail
registers.
Signed-off-by: Radu Nicolau <radu.nicolau@intel.com>
Acked-by: Qi Zhang <qi.z.zhang@intel.com>
Restrict the "remove l3_l4_xsum_errors from rx_errors" to 82599 only for
hardware errata.
Fixes: 256ff05a9c ("ixgbe: fix Rx errors statistics for UDP checksum")
Cc: stable@dpdk.org
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Acked-by: Qi Zhang <qi.z.zhang@intel.com>
The mlx5 PMD allocated the resources of the sample actions, and then
moved these ones to the destination actions array. The original indices
were not cleared and the resources were referenced twice in the
flow object - as the fate actions and in the destination actions array.
This causes the failure on flow destroy because PMD tried to release the
same objects twice.
The patch clears the original indices, add the missed checking for zero
and eliminates multiple object releasing.
Fixes: 00c10c2211 ("net/mlx5: update translate function for mirroring")
Cc: stable@dpdk.org
Signed-off-by: Jiawei Wang <jiaweiw@nvidia.com>
Reviewed-by: Suanming Mou <suanmingm@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
If RSS action contains non zero hash key length and NULL
key buffer pointer the default hash key should be used.
The check for the NULL pointer this was missing in the mlx4
PMD causing crash, for example, in testpmd with command:
flow validate 0 ingress group 0
pattern eth / ipv4 / end
actions rss queues 0 end key_len 40 / end
Fixes: ac8d22de23 ("ethdev: flatten RSS configuration in flow API")
Cc: stable@dpdk.org
Signed-off-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Acked-by: Matan Azrad <matan@nvidia.com>
When RSS expand, if there is no expansion happened but completion
happened because user only input next protocol field instead of item
i.e, ether type == 0x8100 instead of VLAN, an extra flow is created with
missing item in order to filter traffic strictly.
However, after [1] and [2] the rte_flow_item_eth itself is enough to
filter out VLAN traffic, the VLAN item is not needed.
[1]: commit 09315fc838 ("ethdev: add VLAN attributes to ethernet and VLAN items")
[2]: commit 86b59a1af6 ("net/mlx5: support VLAN matching fields")
This redundant flow will cause failure in some scenarios on group 0 due
to they are the same FTE.
Fixes: fc2dd8dd49 ("ethdev: fix expand RSS flows")
Cc: stable@dpdk.org
Signed-off-by: Xiaoyu Min <jackmin@nvidia.com>
Acked-by: Matan Azrad <matan@nvidia.com>
Extend the range of immediate value used in the MODIFY_FIELD action
from 32 to 64 bits to conform to the rte_flow_action_modify_data spec.
Apply appropriate big endian conversion to the immediate value
according to a destination field bit width.
Fixes: 641dbe4fb0 ("net/mlx5: support modify field flow action")
Cc: stable@dpdk.org
Signed-off-by: Alexander Kozyrev <akozyrev@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Converting modify_field action masks to the big endian format is wrong
for small (less than 4 bytes) fields. Use the BE conversions appropriate
for a field size, not rte_cpu_to_be_32 for everything.
Fixes: 144127ba56 ("net/mlx5: adjust modify field action endianness")
Cc: stable@dpdk.org
Signed-off-by: Alexander Kozyrev <akozyrev@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Mellanox hardware can only modify any packet field in 32-bit chunks,
which means 4 such chunks are needed to modify an IPv6 address.
The modification order of these chunks starts from the most significant
bits for the IPv6 address. That leads to confusing results when trying
to modify either source or destination address via the MODIFY_FIELD
action. Fix the order of 32-bit chunks for IPv6 addresses modification
by starting from the least significant bits.
Fixes: 641dbe4fb0 ("net/mlx5: support modify field flow action")
Cc: stable@dpdk.org
Signed-off-by: Alexander Kozyrev <akozyrev@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
In Windows DevX returns the rate of the current link speed
in bit/s, this rate was converted to Mibit/s instead of the Mbit/s
rate expected by DPDK resulting in wrong link speed reporting.
Fixes: 6fbd73709e ("net/mlx5: support link update on Windows")
Cc: stable@dpdk.org
Signed-off-by: Tal Shnaiderman <talshn@nvidia.com>
Acked-by: Matan Azrad <matan@nvidia.com>
The MODIFY_FIELD action requires the extended metadata support
in order to manipulate on METADATA register as well as on MARK register.
Check if it is supported and reject the MODIFY_FIELD action if it is not
just like it was done before for the MARK register modifications.
Fixes: 0588d64ffd ("net/mlx5: check extended metadata for mark modification")
Cc: stable@dpdk.org
Signed-off-by: Alexander Kozyrev <akozyrev@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
