Commit 'dc36bd5dfdeb' mistakenly initializes ret as -rte_errno, then
return ret if ice_search_pattern_match_item fails, if rte_errno happens
to be 0 in this case, it would cause an unrecognized flow rule to be
marked as recognition success. Later, when the code tries to parse the
flow rule, a segmentation fault will occur due to null pointer
reference.
Fixes: dc36bd5dfdeb ("net/ice: fix flow FDIR/switch memory leak")
Cc: stable@dpdk.org
Signed-off-by: Tao Zhu <taox.zhu@intel.com>
Reviewed-by: Xiaolong Ye <xiaolong.ye@intel.com>
Lack of GL_SWR_PM_UP_THR value for mac type 4x10G X722 caused it can't
reach line rate in one queue one core forwarding case. It's about 1%
performance drop. This patch adds value as:
Device-ID Value Comments
0x37D0 0x03030303 4x10G FPK
This value is hardware specific.
Fixes: 3320d4a240da ("net/i40e: workaround performance degradation")
Cc: stable@dpdk.org
Signed-off-by: Qiming Yang <qiming.yang@intel.com>
Acked-by: Xiaolong Ye <xiaolong.ye@intel.com>
Since qpairs is part of the vdev arguments, there is no need to
limit it to 16. The queue arrays can be dynamically sized based
on the requested parameters.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: John W. Linville <linville@tuxdriver.com>
The VLAN 16 bits tci field contains both values of PCP and VID. When
extracting any one of them - it is required not to affect the other one.
Previous to this commit in routine flow_dev_get_vlan_info_from_items()
we calculated the PCP as follows:
(1) vlan->vlan_tci &= MLX5DV_FLOW_VLAN_PCP_MASK;
(2) vlan->vlan_tci |= <3 bits value of PCP>
In line (1) we should have used the negated mask ('~' operator) such
that only the PCP bits will be nullified before ORing them with the
updated PCP value.
Fixes: 9aee7a8418d4 ("net/mlx5: support push flow action on VLAN header")
Cc: stable@dpdk.org
Signed-off-by: Ophir Munk <ophirmu@mellanox.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@mellanox.com>
If configuring VF promiscuous mode is not supported, return '-ENOTSUP'
error code in '.promiscuous_enable/disable' dev_ops.
This is to fix the port start during config restore, where if
'.promiscuous_enable/disable' dev_ops exists and return any value other
than '-ENOTSUP', start will fail.
Same is done for '.allmulticast_enable/disable' dev_ops.
Fixes: ddc7cb0d9453 ("net/i40e: re-program promiscuous mode on VF interface")
Cc: stable@dpdk.org
Signed-off-by: Xiao Zhang <xiao.zhang@intel.com>
Reviewed-by: Xiaolong Ye <xiaolong.ye@intel.com>
Add support for .set_link_up/down() eth ops to bring
link up and down.
Signed-off-by: Harman Kalra <hkalra@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Loopback devices are exposed as ethdev device in octeontx2.
This patch fixes the link information for loopback ports.
Fixes: 38f566280abb ("net/octeontx2: add link stats operations")
Cc: stable@dpdk.org
Signed-off-by: Ashish Gupta <ashishg@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Since packet is talking to a network device (probably tap)
it is possible for the device driver to change the hardware address
by making an ioctl to kernel.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
The devices of the family ConnectX may have two letters as suffix.
Such suffix is preceded with a space and the second x is lowercase:
- ConnectX-4 Lx
- ConnectX-5 Ex
- ConnectX-6 Dx
Uppercase of the device family name BlueField is also fixed.
The lists of supported devices are fixed.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
The routine sending packets with Multi-Packet Write method assigns
the wqe_last variable with transmit descriptor (WQE - work queue entry)
being built. If send queue is close to full state, the WQE has no data
yet (trying to put the first packet) and there is no enough space
in descriptor for the next packet the WQE is discarded and the stored
wqe_last value becomes invalid - points to the discarded WQE.
The mlx5_tx_burst_request_completion() routine might set the completion
request flags in the WQE pointed by wqe_last, it is safe, but the next
mlx5_tx_burst call uses the WQE as the first free one and request
completion flags might be overwritten and completion request will be
lost causing the transmit datapath malfunction.
Fixes: 8b581c690a54 ("net/mlx5: move Tx complete request routine")
Cc: stable@dpdk.org
Signed-off-by: Viacheslav Ovsiienko <viacheslavo@mellanox.com>
Acked-by: Matan Azrad <matan@mellanox.com>
In order to move the mbuf metadata from the WQE to the FDB steering
domain, the PMD add for each NIC TX flow a new action to copy the
metadata register REG_A to REG_C_0.
This copy action is considered as modify header action from HW
perspective.
The HW doesn't support to do modify header action after ant
encapsulation action.
The split metadata function wrongly added the copy action in the end of
the original actions list, hence, NIC egress flow with encapsulation
action failed when the PMD worked with dv_xmeta_en mode.
Move the copy action to be before and back to back with the
encapsulation action for the aforementioned case.
Fixes: 71e254bc0294 ("net/mlx5: split Rx flows to provide metadata copy")
Cc: stable@dpdk.org
Signed-off-by: Matan Azrad <matan@mellanox.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@mellanox.com>
When running mlx5_dev_start in mlx5_ethdev the function calls
mlx5_dev_configure_rss_reta in order to configure the rxq's.
Before mlx5_dev_configure_rss_reta there isn't a check whether
there are rxq's and if rxq's are 0 the function fails.
For example, this command:
/build/app/test-pmd/testpmd -n 4 -w 0000:08:00.0,rx_vec_en=0
-- --burst=64 --mbcache=512 -i --nb-cores=27 --txd=2048 --rxd=2048
--vxlan-gpe-port=6081 --mp-alloc=xbuf --rxq 0 --forward-mode=txonly
would fail.
In order to fix this issue, we should call mlx5_dev_configure_rss_reta
only if we have rxq's.
Fixes: 63bd16292c3a ("net/mlx5: support RSS on hairpin")
Cc: stable@dpdk.org
Reported-by: Sylvain Rodon <srn@nexatech.fr>
Signed-off-by: Shiri Kuzin <shirik@mellanox.com>
Acked-by: Matan Azrad <matan@mellanox.com>
HW supports match on one Ethertype, the Ethertype following the last
VLAN tag of the packet (see PRM).
Previous patch added specific handling for packets with VLAN tag,
after setting match on Ethertype.
This patch moves the handling of packets with VLAN tag, to be done
before and instead of setting match on Ethertype.
Previous patch also added, as part of specific handling for packets
with VLAN tag, the setting of cvlan_tag mask bit in translation of
L3 items.
In case of L3 tunnel there is no inner L2 header, so setting this
mask bit is wrong and causes match failures.
This patch adds check to make sure L2 header exists before setting
cvlan_tag mask bit for L3 items.
Fixes: 00f75a40576b ("net/mlx5: fix VLAN match for DV mode")
Cc: stable@dpdk.org
Signed-off-by: Dekel Peled <dekelp@mellanox.com>
Acked-by: Matan Azrad <matan@mellanox.com>
Tested-by: Raslan Darawsheh <rasland@mellanox.com>
Meter suffix subflow only has the port id and tag match item, if VLAN
push and set VLAN id actions exist in the suffix subflow, the user
defined VLAN items is required for the actions to set a correct VLAN
id.
Currently, the VLAN item stays in the meter prefix subflow. Without
the VLAN item, VLAN id or pcp will not be inherited.
Actions require the VLAN item as below:
RTE_FLOW_ACTION_TYPE_OF_PUSH_VLAN
RTE_FLOW_ACTION_TYPE_OF_SET_VLAN_VID
Add a private VLAN item to copy the user defined VLAN item to the meter
suffix subflow, so the suffix subflow will have the chance to get the
correct original VLAN id and pcp value from the VLAN item.
Fixes: 9ea9b049a960 ("net/mlx5: split meter flow")
Cc: stable@dpdk.org
Signed-off-by: Suanming Mou <suanmingm@mellanox.com>
Acked-by: Matan Azrad <matan@mellanox.com>
As meter flows are split into three subflows each, the prefix subflow
with meter action color the packet, the meter subflow filters out the
colored packets, the suffix subflow applies all the remaining actions
to the passed packets.
Currently, all the user defined items are matched in the prefix flow.
Flow id tag match item is the only item added to the meter suffix
subflow. Some of the remaining actions to be applied in the suffix
subflow require more information in the match item, or the suffix
subflow will not be created successfully.
Actions require the L3/L4 type in the match items as below:
RTE_FLOW_ACTION_TYPE_SET_TP_SRC
RTE_FLOW_ACTION_TYPE_SET_TP_DST
RTE_FLOW_ACTION_TYPE_DEC_TTL
RTE_FLOW_ACTION_TYPE_SET_TTL
RTE_FLOW_ACTION_TYPE_RSS
RTE_FLOW_ACTION_TYPE_QUEUE
Inherit the match item flags from meter prefix subflow to make actions
in suffix subflow get sufficient information.
Fixes: 9ea9b049a960 ("net/mlx5: split meter flow")
Cc: stable@dpdk.org
Signed-off-by: Suanming Mou <suanmingm@mellanox.com>
Acked-by: Matan Azrad <matan@mellanox.com>
Metadata suffix subflow inherits the RSS needed hash_fields from the
prefix subflow as the suffix subflow only has the tag match item unable
to generate the full original hash_fields for RSS action.
Unfortunately, hash_fields will only be generated if flow has RSS
action. So it means the prefix flow won't generate the hash_fields as
the RSS action has been split to the suffix flow.
Copy the layer flags from prefix subflow to suffix subflow to help the
suffix subflow to generate the correct hash_fields itself.
Fixes: 71e254bc0294 ("net/mlx5: split Rx flows to provide metadata copy")
Cc: stable@dpdk.org
Signed-off-by: Suanming Mou <suanmingm@mellanox.com>
Acked-by: Matan Azrad <matan@mellanox.com>
Currently, for header modify actions after tunnel decapsulation, the
header modify actions will still select the old outermost layer type.
It will cause header modify actions get the wrong layer type.
Add the tunnel decap flag to indicate the layer type to get for header
modify actions.
Fixes: 4bb14c83df95 ("net/mlx5: support modify header using Direct Verbs")
Cc: stable@dpdk.org
Signed-off-by: Suanming Mou <suanmingm@mellanox.com>
Acked-by: Matan Azrad <matan@mellanox.com>
Currently, the flow validate function only validate the outermost layer
with the header modify actions. If there is decapsulation action before
the header modify action, the validation should choose the inner layer
for validation.
Add decapsulation check when validate with the header modify actions.
Choose the inner layer once there is decapsulation action.
Fixes: 4bb14c83df95 ("net/mlx5: support modify header using Direct Verbs")
Cc: stable@dpdk.org
Signed-off-by: Suanming Mou <suanmingm@mellanox.com>
Acked-by: Matan Azrad <matan@mellanox.com>
Currently, the set VLAN ID header modify action has already got the
action pointer with offset from the header modify action array, but
the configuration saves the detail to the memory of action with the
offset again. It causes double offset to set the VLAN ID action to
the wrong place in the header modify array.
Remove the offset when get the action pointer to fix that issue.
Fixes: 5f163d520cff ("net/mlx5: support modify VLAN ID on existing VLAN header")
Cc: stable@dpdk.org
Signed-off-by: Suanming Mou <suanmingm@mellanox.com>
Acked-by: Dekel Peled <dekelp@mellanox.com>
Acked-by: Matan Azrad <matan@mellanox.com>
Fix a race condition between port stop and error recovery task. When io
forwarding is not started on Stingray devices, driver will not receive
the async event from FW when there is a FW reset. While exiting testpmd,
as part of port stop driver sees this event and this in turn causes a
race between port stop and error recovery task.
Fixed this by ignoring the fatal/non-fatal async event from FW while
stopping port.
Fixes: df6cd7c1f73a ("net/bnxt: handle reset notify async event from FW")
Cc: stable@dpdk.org
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Rahul Gupta <rahul.gupta@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Check for bp->hwrm_cmd_resp_addr before using it in HWRM_PREP to avoid
segmentation fault when stop port and meanwhile receive events from FW.
Fixes: df6cd7c1f73a ("net/bnxt: handle reset notify async event from FW")
Cc: stable@dpdk.org
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Operator '<<' should be used instead of '<' for shifting value to be
set in MSI-X configuration register.
Old code adds 1 on even MSI-X interrupt vector index used by queue,
resulting in interrupt mapping error.
Fixes: 65dfc889d86b ("net/ice: support Rx queue interruption")
Cc: stable@dpdk.org
Signed-off-by: Tao Zhu <taox.zhu@intel.com>
Acked-by: Xiaolong Ye <xiaolong.ye@intel.com>
'fm10k_rxtx_vec.c' is SSE vector instructions implementation and should
be compiled only for x86.
The vector PMD support controlled by
'CONFIG_RTE_LIBRTE_FM10K_INC_VECTOR' config option, but it is enabled by
default, safer to add x86 checks too.
Fixes: 10eb9ce8dccd ("fm10k: allow to disable vector driver")
Cc: stable@dpdk.org
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Xiao Wang <xiao.w.wang@intel.com>
The format specifier for the 'size_t' format should be '%z'.
Also this fix enables compiling PMD for 32bit architecture.
Fixes: ba641f207642 ("net/sfc: add init on attach")
Fixes: 82faef507608 ("net/sfc: set RSS key and hash types config")
Fixes: 7803554a9e38 ("net/sfc: process RSS settings on Rx configure step")
Cc: stable@dpdk.org
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Reviewed-by: Andrew Rybchenko <arybchenko@solarflare.com>
The RSS expansion feature was introduced to split RSS flows according to
the adjustment between the RSS types and the flow items.
The expansion function gets an item tree for the above adjustment from
the caller which reflects the HW needs.
The standard vxlan header next protocol is always Ethernet while there
are some Mellanox customers who use their own method to allow L3
headers after the vxlan tunnel header.
The expansion tree of mlx5 PMD didn't expect to get L3 headers after the
vxlan header what caused a failure in flow creation when inner RSS is
requested on L3 after vxlan flow.
Add IPV4 and IPV6 as optional headers after vxlan in the RSS expansion
tree to allow L3 tunnel support for vxlan.
Fixes: f4f06e361516 ("net/mlx5: add flow VXLAN item")
Cc: stable@dpdk.org
Signed-off-by: Matan Azrad <matan@mellanox.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@mellanox.com>
The hairpin TX/RX queue depth and packet size is fixed in the past.
When the firmware has some fix or improvement, the PMD will not
make full use of it. And also, 32 packets for a single queue will not
guarantee a good performance for hairpin flows. It will make the
stride size larger and for small packets, it is a waste of memory.
The recommended stride size is 64B now.
The parameter of hairpin queue setup needs to be adjusted.
1. A proper buffer size should support the standard jumbo frame with
9KB, and also more than 1 jumbo frame packet for performance.
2. Number of packets of a single queue should be the maximum
supported value (total buffer size / stride size).
There is no need to support the max capacity of total buffer size
because the memory consumption should also be taken into
consideration.
Fixes: e79c9be91515 ("net/mlx5: support Rx hairpin queues")
Cc: stable@dpdk.org
Signed-off-by: Bing Zhao <bingz@mellanox.com>
Acked-by: Ori Kam <orika@mellanox.com>
The new Mellanox devices support GENEVE tunnel stateless offloads by
native HW parsers, FW doesn't need to configure flex parser to support
it.
The FW capability for GENEVE flex parser is not set for the above
devices, hence the GENEVE flow validation failed for them.
Remove the flex parser validation for GENEVE, stay only with the direct
FW capability for GENEVE support.
Fixes: e59a5dbcfd07 ("net/mlx5: add flow match on GENEVE item")
Cc: stable@dpdk.org
Signed-off-by: Matan Azrad <matan@mellanox.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@mellanox.com>
The RTE_FLOW_ITEM_TYPE_GRE_KEY means that GRE key should
be present on the flow and in addition can explicitly match on the GRE
key field itself.
When no value is set in this item any GRE key should match the flow.
The match on GRE key wrongly was not added if the item fields are NULL
while at least the GRE key should be present in the flow.
Add the GRE key present match when RTE_FLOW_ITEM_TYPE_GRE_KEY is in
the flow item list.
Fixes: a7a0365565a4 ("net/mlx5: match GRE key and present bits")
Cc: stable@dpdk.org
Signed-off-by: Matan Azrad <matan@mellanox.com>
Acked-by: Ori Kam <orika@mellanox.com>
ICMPv6 header contains the checksum field, that includes the IP
addresses from IP header.
The ConnectX-5 hardware does not support ICMPv6 checksum calculation
and in case of IP header modification the checksum will contain
the wrong value.
The patch rejects the header modification actions related to IP
addresses if ICMPv6 protocol is detected in pattern.
This issue was also partly fixed in commit below which rejects
flows with the pattern "ipv6 proto is 58".
Fixes: 0e2ceb639d8a ("net/mlx5: fix ICMPv6 header rewrite actions")
Cc: stable@dpdk.org
Signed-off-by: Shiri Kuzin <shirik@mellanox.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@mellanox.com>
Acked-by: Matan Azrad <matan@mellanox.com>
Changed the ABI version to 20.0.1.
Fixes: a72cf98cc93e ("net/ionic: add skeleton")
Reported-by: David Marchand <david.marchand@redhat.com>
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Ethdev's .dev_configure callback can be called multiple
time during a device life-time, but Vhost makes the
wrong assumption that it is not the case and try to
setup again the device on reconfiguration.
This patch ensures the device hasn't been already setup
before proceeding.
Fixes: 3d01b759d267 ("net/vhost: delay driver setup")
Cc: stable@dpdk.org
Reported-by: Yinan Wang <yinan.wang@intel.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Tested-by: Yinan Wang <yinan.wang@intel.com>
Reviewed-by: David Marchand <david.marchand@redhat.com>
Reviewed-by: Tiwei Bie <tiwei.bie@intel.com>
If for some reason vhost_driver_setup() fails, the list
element for the device may be freed without being removed
from the internal list of devices.
This patch fixes all the error paths, by unregistering the
device from Vhost library it has been registered, remove
the device from the list, reset device vring_state pointer
from the global table and only free vring state if it had
been allocated.
Fixes: 3d01b759d267 ("net/vhost: delay driver setup")
Cc: stable@dpdk.org
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: David Marchand <david.marchand@redhat.com>
Reviewed-by: Tiwei Bie <tiwei.bie@intel.com>
When the port restarts, the flow ctrl register will be reset,
we need to make sure it can be configured the same as previous setting,
otherwise a register read error would occur. This patch fixes this
issue.
Fixes: af75078fece3 ("first public release")
Cc: stable@dpdk.org
Signed-off-by: Guinan Sun <guinanx.sun@intel.com>
Tested-by: Tomasz Konieczny <tomaszx.konieczny@intel.com>
Reviewed-by: Xiaolong Ye <xiaolong.ye@intel.com>
Interrupt mapping should be 1:n queue(s).This patch fixes the
logic of interrupt bind by code reconstruction.
Fixes: 6a6cf5f88b4a ("net/i40e: enable multi-queue Rx interrupt for VF")
Signed-off-by: Shougang Wang <shougangx.wang@intel.com>
Acked-by: Qi Zhang <qi.z.zhang@intel.com>
The hardware can recognize and mark the layer 4 protocol type for TCP,
UDP and IPSec non-fragmented packets. For all the fragmented packets,
L4 type will be considered as None. This can be used when creating a
flow with L4 matching, then hops number will be reduced and a better
performance could be gained.
But for ICMP packets, it cannot be recognized correctly because it is
not a L4 protocol in the stack, even if the packet format is similar.
All the fragmented and non-fragmented ICMP will have the None L4 type.
Fragmented packets with incomplete headers could not hit the flow,
even for the first fragment. Because then it will make it complex to
defragment for both HW and SW. For other types, the implicit rules
could be used directly and all the fragments will miss the flow.
For ICMP packets, this should be done explicitly because all packets
have None type. The first fragment will still hit the flow if there is
no explicit rule.
All ICMP fragments will still hit the rules like ETH, ETH + IP, and
ETH + IP + "ICMP protocol" only since they are wildcard rules, and
there is no next layer protocol specified field in such rules.
Fixes: d53aa89aea91 ("net/mlx5: support matching on ICMP/ICMP6")
Cc: stable@dpdk.org
Signed-off-by: Bing Zhao <bingz@mellanox.com>
Acked-by: Ori Kam <orika@mellanox.com>
This adds new device id to the list of Mellanox devices
that runs mlx5 PMD.
- BlueField-2 integrated ConnectX-6 Dx network controller
This device is not ready yet, it is in development stage.
Signed-off-by: Raslan Darawsheh <rasland@mellanox.com>
Reviewed-by: Gavin Hu <gavin.hu@arm.com>
Acked-by: Matan Azrad <matan@mellanox.com>
The PMD manages internally the priority of the flows in addition to the
user configured priority.
So, 2 flows with the same user priority may get different priority.
The method:
As much as the flow is more specific it gets higher priority
(higher means first to be matched).
In addition, When the user creates a RSS flow the PMD splits the flows
according to the flow RSS layers as the HW requests for RSS TIR.
The internal priority for each flow is decided by the flow last layer.
L2, L3 and L4 (L2 low and L4 high).
The tunnel layer was wrongly decided to be L4 all the time, even when
the flow is configured with inner-RSS.
Hence, the first RSS split which takes the tunnel layer priority all the
time will be matched before the more specific splits.
Change the priority of tunnel layer to be L2 when inner-RSS is
configured.
Fixes: d4a405186b73 ("net/mlx5: support tunnel RSS level")
Cc: stable@dpdk.org
Signed-off-by: Matan Azrad <matan@mellanox.com>
Acked-by: Ori Kam <orika@mellanox.com>
For ixgbe, there is restriction that data buffers of any transmitted
packet must include at least 12 bytes of the src/dst Ethernet MAC
addresses as well as 2 bytes of the Type/Len field, otherwise, tx hang
would happen.
This patch adds check for those illegal packets and protects TX from
hanging.
Fixes: 7829b8d52be0 ("net/ixgbe: add Tx preparation")
Cc: stable@dpdk.org
Signed-off-by: Xiao Zhang <xiao.zhang@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Xiaolong Ye <xiaolong.ye@intel.com>
Stopping an already disabled vport leads to firmware
assert. Stop the vport only if it was started.
Fixes: 2ea6f76aff40 ("qede: add core driver")
Cc: stable@dpdk.org
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Rasesh Mody <rmody@marvell.com>
On ungraceful termination of DPDK application, PMD VF driver
fails to re-load due to PF seeing the VF in unexpected state
during VF acquisition handshake.
This patch fixes it by allowing VF to request the PF for soft
FLR during the load in such cases so that it can get cleanly
re-loaded.
Fixes: 2ea6f76aff40 ("qede: add core driver")
Cc: stable@dpdk.org
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Shahed Shaikh <shshaikh@marvell.com>
Signed-off-by: Rasesh Mody <rmody@marvell.com>
Acked-by: Rasesh Mody <rmody@marvell.com>
IXGBE link status task uses rte alarm thread in old implementation.
Sometime ixgbe link status task takes up to 9 seconds. This will
severely affect the rte-alarm-thread dependent tasks in the
system, like interrupt or hotplug event. So replace with an
independent thread which has the same thread affinity settings
as rte interrupt.
Fixes: 0408f47ba4d6 ("net/ixgbe: fix busy polling while fiber link update")
Cc: stable@dpdk.org
Signed-off-by: Tao Zhu <taox.zhu@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Currently when application requests for RTE_FC_NONE earlier
than PMD's internal fc mode update, flow control set routine
is returning without updating the flow control state.
Patch updates the PMD's internal fc mode details during
dev_configure to ensure any flow control set requests
issued later are handled properly.
Fixes: 609945f1ce90 ("net/octeontx2: support flow control")
Cc: stable@dpdk.org
Signed-off-by: Vamsi Attunuru <vattunuru@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Coverity complains of unchecked return value warning of
i40e_xmit_cleanup, while this cleanup is opportunistic and will not
cause problems if it fails. So instead of checking the return value of
i40e_xmit_cleanup and return in case of cleanup failure, we directly
cast it to void function to make the Coverity happy.
Coverity issue: 353617
Fixes: 4861cde46116 ("i40e: new poll mode driver")
Cc: stable@dpdk.org
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Acked-by: Xiaolong Ye <xiaolong.ye@intel.com>
Coverity complains of unchecked return value warning of
ice_xmit_cleanup, while this cleanup is opportunistic and will not cause
problems if it fails. So instead of checking the return value of
ice_xmit_cleanup and return in case of cleanup failure, we directly cast
it to void function to make the Coverity happy.
Coverity issue: 353623
Fixes: 17c7d0f9d6a4 ("net/ice: support basic Rx/Tx")
Cc: stable@dpdk.org
Signed-off-by: Sunil Pai G <sunil.pai.g@intel.com>
Acked-by: Xiaolong Ye <xiaolong.ye@intel.com>
This patch removes an unused member from pmd_internal.
Signed-off-by: Itsuro Oda <oda@valinux.co.jp>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
This patch adds lacking member setting and makes secondary
probe complete.
Fixes: 4852aa8f6e21 ("drivers/net: enable hotplug on secondary process")
Cc: stable@dpdk.org
Signed-off-by: Itsuro Oda <oda@valinux.co.jp>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
