Public struct rte_eth_dev_info has a "struct rte_pci_device" field in it
although it is common for all ethdev in all buses.
Replacing pci specific struct with generic device struct and updating
places that are using pci device in a way to get this information from
generic device.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Reviewed-by: David Marchand <david.marchand@6wind.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
A new function was added to get a Tx port index as a function of the
topology mode and the Rx port index.
Use this function to get the Tx port index of simple stream.
Signed-off-by: Matan Azrad <matan@mellanox.com>
The testpmd user can configure port topology mode to define the port
topology between the testpmd forward ports(paired, chained and loop).
When multi-queue ports are configured by the user, the testpmd
streams are created by rss_fwd_config_setup() function, this function
doesn't take into account the chained topology mode and configures the
forward streams with paired topology mode in this case.
Configure the stream Tx port by dedicated function which calculates
a valid Tx port index as a function of the topology mode and the Rx
port index.
Fixes: af75078 ("first public release")
Cc: stable@dpdk.org
Signed-off-by: Matan Azrad <matan@mellanox.com>
When multi-queue ports are configured by the user, the testpmd streams
are created by rss_fwd_config_setup() function.
This function may configure to the streams either invalid Rx ports or
invalid Tx ports.
An invalid Tx port is configured when the number of ports is odd.
In this case, the last Tx port will be always invalid.
An invalid Rx port is configured when NUMA support is configured by the
user and the number of forward ports is much smaller than the number of
all ports. In this case, also the Tx port is invalid.
Change calculations to get valid ports.
Fixes: af75078 ("first public release")
Cc: stable@dpdk.org
Signed-off-by: Matan Azrad <matan@mellanox.com>
Since METER action is supported by the testpmd application
suitable entry should exist in flow actions information table.
Without that testpmd will return error on adding a new flow to
the list of flows attached to a given port.
Fixes: 30ffb4e67ee3 ("app/testpmd: add commands traffic metering and policing")
Cc: stable@dpdk.org
Signed-off-by: Tomasz Duszynski <tdu@semihalf.com>
Acked-by: Jasvinder Singh <jasvinder.singh@intel.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
rte_eth_dev_is_valid_port() API validates each valid port from ethdev
point of view and may validate ports which should not be used by the
application.
Testpmd should use only the ports available through the
RTE_ETH_FOREACH_DEV iterator.
Replace rte_eth_dev_is_valid_port() usage by RTE_ETH_FOREACH_DEV
iterator usage for testpmd ports validation.
Fixes: 7d89b2610353 ("app/testpmd: use ethdev iterator to list devices")
Cc: stable@dpdk.org
Signed-off-by: Matan Azrad <matan@mellanox.com>
Add possibility to load file with raw packet and set it as a
template for FDIR setup.
Signed-off-by: Kirill Rybalchenko <kirill.rybalchenko@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Add the ability to match VNI and protocol fields of GENEVE protocol
header.
Signed-off-by: Roman Zhukov <roman.zhukov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
This command will simulate the process of setting the
eth-peer from command line.
It will be useful to perform extra testing.
usage:
testpmd> set eth-peer <port_id> <peer_addr>.
Signed-off-by: Wisam Jaddo <wisamm@mellanox.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
On ethdev there is an API to configure VLAN offloads after the port
was started and without reconfiguration of the port or queues.
In the current design of the application, when the Rx offloads are
changed (through "port config all" CLI command) the port configuration
is overwritten, therefore the configuration made for the VLAN is lost.
This patch is to address the issue by a configuration of each port Rx
offloads separately instead of using the global Rx config. Such
adjustment is required due to the conversion of the application to the
new offloads API.
Signed-off-by: Shahaf Shuler <shahafs@mellanox.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
In the current design it was possible for offload to be set even though
the device is not supporting it. A warning message was printed instead.
This is a wrong behaviour, as application should set only the offloads
reported by the capabilities of the device.
This patch adds verification for the offloads being set and make sure
the offload configuration passed to the device always match its
capabilities.
Signed-off-by: Shahaf Shuler <shahafs@mellanox.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Since testpmd is now using the new Ethdev offloads API and there is
a way configure each of the tx offloads from CLI or command line,
there is no need for the txqflags configuration anymore.
Signed-off-by: Shahaf Shuler <shahafs@mellanox.com>
Acked-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
The tx_ol_flags field was used in order to control the different
Tx offloads set. After the conversion to the new Ethdev Tx offloads API
it is not needed anymore as the offloads configuration is stored in
ethdev structs.
Signed-off-by: Shahaf Shuler <shahafs@mellanox.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Ethdev Tx offloads API has changed since:
commit cba7f53b717d ("ethdev: introduce Tx queue offloads API")
Convert the application to use the new API.
This patch mandates the port to be stopped when configure the Tx
offloads. This is because the PMD must be aware to the offloads changes
on the device and queue configuration.
Signed-off-by: Shahaf Shuler <shahafs@mellanox.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Ethdev Rx offloads API has changed since:
commit ce17eddefc20 ("ethdev: introduce Rx queue offloads API")
Convert the application to use the new API. The is no functionality
changes rather simple conversion of the flags.
Signed-off-by: Shahaf Shuler <shahafs@mellanox.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
The print of the port configuration was only according to configuration
of the first port.
Fixes: f2c5125a686a ("app/testpmd: use default Rx/Tx port configuration")
Cc: stable@dpdk.org
Signed-off-by: Shahaf Shuler <shahafs@mellanox.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Display some more useful information from dev_info when
calling "show port info <portid>".
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
When defining two failsafe devices in testpmd the port numbers of the
failsafe devices may not be consecutive.
For example: if failsafe device includes a PCI device and a TAP device
then failsafe port numbers would be 0 and 3.
Port 0 - failsafe #1 device
Port 1 - PCI #1 device
Port 2 - TAP #1 device
Port 3 - failsafe #2 device
Port 4 - PCI #2 device
Port 5 - TAP #2 device
If forwarding is defined between the failsafe devices including a peer
address the forwarding should be between peer addresses of ports 0
and 3. Instead testpmd establishes forwarding between peer addresses
of consecutive ports 0 and 1. This commit fixes this bug.
Fixes: af75078fece3 ("first public release")
Cc: stable@dpdk.org
Signed-off-by: Ophir Munk <ophirmu@mellanox.com>
Signed-off-by: Raslan Darawsheh <rasland@mellanox.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
When using "show port xstats all" command to show xstats, the output
is usually too long to obtain what you really want, especially when
multi-queue is enabled.
Added an option to set whether zero values should be displayed
or not for xstats. The "set xstats-hide-zero on|off" command enables
the user to decide if the zero values should be shown while
displaying xstats.
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Signed-off-by: Elza Mathew <elza.mathew@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Fixes: 4cfe399f6550 ("net/bnxt: support to set VF rxmode")
Fixes: 36735a932ca7 ("net/bnxt: support set VF QOS and MAC anti spoof")
Cc: stable@dpdk.org
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
This patch add a API configuration of queue region in rss.
It can parse the parameters of region index, queue number,
queue start index, user priority, traffic classes and so on.
According to commands from command line, it will call i40e
private API and start the process of set or flush queue region
configure. As this feature is specific for i40e, so private API
will be used. Aslo add a document for these new commands.
Queue region only support PF by now, so this document is
only for configuration of queue region on PF port.
Signed-off-by: Wei Zhao <wei.zhao1@intel.com>
This issue was about passing unsigned argument where should be signed
number.
In reality this is about wrong usage of fseek and ftell to determine
filesize.
This patch is compliant to suggestions from FIO19-C:
"Do not use fseek() and ftell() to compute the size of a regular file"
Coverity issue: 143454
Fixes: a92a5a2cbbff ("app/testpmd: add command for loading DDP")
Cc: stable@dpdk.org
Signed-off-by: Daniel Mrzyglod <danielx.t.mrzyglod@intel.com>
Acked-by: Beilei Xing <beilei.xing@intel.com>
This patch adds GSO support to the csum forwarding engine. Oversized
packets transmitted over a GSO-enabled port will undergo segmentation
(with the exception of packet-types unsupported by the GSO library).
GSO support is disabled by default.
GSO support may be toggled on a per-port basis, using the command:
"set port <port_id> gso on|off"
The maximum packet length (including the packet header and payload) for
GSO segments may be set with the command:
"set gso segsz <length>"
Show GSO configuration for a given port with the command:
"show port <port_id> gso"
Signed-off-by: Jiayu Hu <jiayu.hu@intel.com>
Signed-off-by: Mark Kavanagh <mark.b.kavanagh@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The GRO library provides two modes to reassemble packets. Currently, the
csum forwarding engine has supported to use the lightweight mode to
reassemble TCP/IPv4 packets. This patch introduces the heavyweight mode
for TCP/IPv4 GRO in the csum forwarding engine.
With the command "set port <port_id> gro on|off", users can enable
TCP/IPv4 GRO for a given port. With the command "set gro flush <cycles>",
users can determine when the GROed TCP/IPv4 packets are flushed from
reassembly tables. With the command "show port <port_id> gro", users can
display GRO configuration.
The GRO library doesn't re-calculate checksums for merged packets. If
users want the merged packets to have correct IP and TCP checksums,
please select HW IP checksum calculation and HW TCP checksum calculation
for the port which the merged packets are transmitted to.
Signed-off-by: Jiayu Hu <jiayu.hu@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Tested-by: Lei Yao <lei.a.yao@intel.com>
Extend port_id definition from uint8_t to uint16_t in lib and drivers
data structures, specifically rte_eth_dev_data. Modify the APIs,
drivers and app using port_id at the same time.
Fix some checkpatch issues from the original code and remove some
unnecessary cast operations.
release_17_11 and deprecation docs have been updated in this patch.
Signed-off-by: Zhiyong Yang <zhiyong.yang@intel.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Port info command prints information about all supported flow types,
including dynamically mapped ones.
Signed-off-by: Kirill Rybalchenko <kirill.rybalchenko@intel.com>
Reviewed-by: Jingjing Wu <jingjing.wu@intel.com>
Testpmd calculates packet throughput by getting a diff of previous stats
value and current one.
If a stats clear called after previous sample taken, the diff will be
negative and throughput calculation will be wrong.
If current stats value is smaller than previous one, set throughput to
zero.
Fixes: 0e106980301d ("app/testpmd: show throughput in port stats")
Cc: stable@dpdk.org
Signed-off-by: Wei Zhao <wei.zhao1@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
The testpmd was doing old BSD lint style casts of rte_memcpy
to (void). This is unnecessary.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Kirill Rybalchenko <kirill.rybalchenko@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
The corrupted code checks only RAW flow item type special case for
returning its size but doesn't deal with any other flow item type
and returns 0 for all the others.
This bug leaves the flow descriptor empty for non RAW types.
The fix takes the correct size to any regular types from appropriate
array.
The same issue, with a similar fix, is in flow action size method which
deals only with RSS special type.
Fixes: 938a184a1870 ("app/testpmd: implement basic support for flow API")
Cc: stable@dpdk.org
Signed-off-by: Matan Azrad <matan@mellanox.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
This patch enables TCP/IPv4 GRO library in csum forwarding engine.
By default, GRO is turned off. Users can use command "gro (on|off)
(port_id)" to enable or disable GRO for a given port. If a port is
enabled GRO, all TCP/IPv4 packets received from the port are performed
GRO. Besides, users can set max flow number and packets number per-flow
by command "gro set (max_flow_num) (max_item_num_per_flow) (port_id)".
Signed-off-by: Jiayu Hu <jiayu.hu@intel.com>
Reviewed-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Lei Yao <lei.a.yao@intel.com>
Add new meta pattern item RTE_FLOW_TYPE_ITEM_FUZZY in flow API.
This is for device that support fuzzy match option.
Usually a fuzzy match is fast but the cost is accuracy.
i.e. Signature Match only match pattern's hash value, but it is
possible that two different patterns have the same hash value.
Matching accuracy level can be configured by subfield threshold.
Driver can divide the range of threshold and map to different
accuracy levels that device support.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
These functions are supported only on ixgbe.
However, they should appear in the help and returns an error
if the function is not supported or not enabled.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Isolated mode can be requested by applications on individual ports to avoid
ingress traffic outside of the flow rules they define.
Besides making ingress more deterministic, it allows PMDs to safely reuse
resources otherwise assigned to handle the remaining traffic, such as
global RSS configuration settings, VLAN filters, MAC address entries,
legacy filter API rules and so on in order to expand the set of possible
flow rule types.
To minimize code complexity, PMDs implementing this mode may provide
partial (or even no) support for flow rules when not enabled (e.g. no
priorities, no RSS action). Applications written to use the flow API are
therefore encouraged to enable it.
Once effective, leaving isolated mode may not be possible depending on PMD
implementation.
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Acked-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Acked-by: Andrew Rybchenko <arybchenko@solarflare.com>
This patch adds support to
1) enable VF MAC anti spoof.
2) QOS configuration for specified VF.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Application fails to create NVGRE and E-Tag flows with
current configuration, this commit fixes the issue by
adding flow items for E_TAG and NVGRE.
Fixes: e4840ef2685d ("ethdev: fix incomplete items in flow API")
Cc: stable@dpdk.org
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Revert patches to provide clear view for
upcoming changes. Reverted patches are listed below:
commit ea85e7d711b6 ("ethdev: retrieve xstats by ID")
commit a954495245c4 ("ethdev: get xstats ID by name")
commit 1223608adb9b ("app/proc-info: support xstats by ID")
commit 25e38f09af9c ("net/e1000: support xstats by ID")
commit 923419333f5a ("net/ixgbe: support xstats by ID")
Signed-off-by: Kuba Kozak <kubax.kozak@intel.com>
Extended xstats API in ethdev library to allow grouping of stats
logically so they can be retrieved per logical grouping managed
by the application.
Changed existing functions rte_eth_xstats_get_names and
rte_eth_xstats_get to use a new list of arguments: array of ids
and array of values. ABI versioning mechanism was used to
support backward compatibility.
Introduced two new functions rte_eth_xstats_get_all and
rte_eth_xstats_get_names_all which keeps functionality of the
previous ones (respectively rte_eth_xstats_get and
rte_eth_xstats_get_names) but use new API inside.
test-pmd: add support for new xstats API retrieving by id in
testpmd application: xstats_get() and
xstats_get_names() call with modified parameters.
doc: add description for modified xstats API
Documentation change for modified extended statistics API functions.
The old API only allows retrieval of *all* of the NIC statistics
at once. Given this requires a MMIO read PCI transaction per statistic
it is an inefficient way of retrieving just a few key statistics.
Often a monitoring agent only has an interest in a few key statistics,
and the old API forces wasting CPU time and PCIe bandwidth in retrieving
*all* statistics; even those that the application didn't explicitly
show an interest in.
The new, more flexible API allow retrieval of statistics per ID.
If a PMD wishes, it can be implemented to read just the required
NIC registers. As a result, the monitoring application no longer wastes
PCIe bandwidth and CPU time.
Signed-off-by: Jacek Piasecki <jacekx.piasecki@intel.com>
Signed-off-by: Kuba Kozak <kubax.kozak@intel.com>
Signed-off-by: Tomasz Kulasek <tomaszx.kulasek@intel.com>
Acked-by: Harry van Haaren <harry.van.haaren@intel.com>
This patch adds MTU display to "show port info" command.
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
This patch exposes the following item fields through the flow command:
- MPLS label
- GRE protocol
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Add two new commands "show port cap <port>" and "show
port cap all" to display what offload capabilities supported
in ports. It will not only display all the capabilities of
the port, but also the enabling condition for each capability
in the running time.
Signed-off-by: Qiming Yang <qiming.yang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Beilei Xing <beilei.xing@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
modify set_vf_rx_vlan function to handle the i40e PMD.
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Vincent Jardin <vincent.jardin@6wind.com>
