Add support for 8.14.x.x firmware.
The new firmware adds support for external PHY BCM8485x; configures
fixed link speed with transceiver/cable not supporting negotiation;
supports engine swap; supports overriding PCIe preset equalization
value; checks pause too long for ports and reads die temperature
every second for shutdown threshold.
It includes change in FLR flow when there is a SW initiated FLR.
Signed-off-by: Rasesh Mody <rasesh.mody@cavium.com>
This patch implements NFP PMD support for TSO but it also requires
a firmware advertising the capability.
Signed-off-by: Alejandro Lucero <alejandro.lucero@netronome.com>
NFP supports more speeds than just 40 and 100GB, which were
what was advertised before.
Signed-off-by: Alejandro Lucero <alejandro.lucero@netronome.com>
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Mark Spender <mspender@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
Extract RSS hash provided by the HW in the prefix and put it to mbuf.
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
IPv4 header and TCP/UDP checksums for both IPv4 and IPv6 are supported.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
Does not implement any deprecated statistics.
No per-queue statistics yet.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
Supported options are auto (based on NIC firmware variant and
installed licences), throughput, low-latency.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
The PMD allows for DPDK and the host to communicate using a raw
device interface on the host and in the DPDK application. The device
created is a Tap device with a L2 packet header.
Signed-off-by: Keith Wiles <keith.wiles@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Tested-by: Aws Ismail <aismail@ciena.com>
Tested-by: Vasily Philipov <vasilyf@mellanox.com>
remove the following API's:
rte_eth_dev_set_vf_rxmode
rte_eth_dev_set_vf_rx
rte_eth_dev_set_vf_tx
rte_eth_dev_set_vf_vlan_filter
rte_eth_dev_set_vf_rate_limit
Increment LIBABIVER in Makefile
Remove deprecation notice for removing rte_eth_dev_set_vf_* API's.
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Check that Rx mbuf pool, MTU and Rx scatter config are in sync.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Resources required in accordance with configuration are
allocated only.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Manual link speed/duplex configuration is not supported yet.
Loopback is not supported yet.
Flow Director is not supported.
Link status change notification using interrupt is not supported yet.
Receive data notification using interrupts is not supported yet.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Enable the PMD by default on supported configurations.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
This patch adds a new function eth_igb_fw_version_get.
Signed-off-by: Qiming Yang <qiming.yang@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
This patch adds a new API 'rte_eth_dev_fw_version_get' for
fetching firmware version by a given device.
Signed-off-by: Qiming Yang <qiming.yang@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Last changes in Niantic and Fortville NIC drivers causes that
vector Rx path is chosen by default in l3fwd-thread application.
This path doesn't support propagation of hw packet type recognition
to the packet_type field in mbuf, and packets cannot be classified
properly.
The approach to solve this problem is similar to the commit:
71a7e2424e07 ("examples/l3fwd: fix using packet type blindly").
To use sw packet analyzer, new command line option "--parse-ptype" is
introduced.
Signed-off-by: Tomasz Kulasek <tomaszx.kulasek@intel.com>
A referenced document in the Linux Kernel has been moved to a
sub-directory. And kernel community has moved to RST/Sphinx. The links are
replaced with HTML rendered links.
Signed-off-by: Yongseok Koh <yskoh@mellanox.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
L3 Forwarding sample app user guides have some inconsistencies
between the example command line and the configuration table.
Also, they were showing too complicated configuration, using two
different NUMA nodes for two ports, which will probably lead
to performance drop due to use cross-socket channel.
This patch simplifies the configuration of these examples,
by using a single NUMA node and a single queue per port.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
This patch fixes a trivial typo in testpmd application guide.
Signed-off-by: Rami Rosen <rami.rosen@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
This patch mainly allocates structure to store queue/irq mapping,
and configure queue/irq mapping down through PCI ops. It also creates
eventfds for each Rx queue and tell the kernel about the eventfd/intr
binding.
Note: So far, we hard-code 1:1 queue/irq mapping (each rx queue has
one exclusive interrupt), like this:
vec 0 -> config irq
vec 1 -> rxq0
vec 2 -> rxq1
...
which means, the "vectors" option of QEMU should be configured with
a value >= N+1 (N is the number of the queue pairs).
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Tested-by: Lei Yao <lei.a.yao@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
