Since the return value of the '.stats_reset' and '.xstats_reset'
callback function is int, when failing to issue command to firmware to
execute clear statistics, the relevant callback function should return
non-zero value.
Fixes: 8839c5e202f3 ("net/hns3: support device stats")
Cc: stable@dpdk.org
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Currently, based on hns3 VF device error may occur during initialization.
The root cause as below:
When the following formula is executed during initialization, the
private variable named hw->tqps_num has not been obtained from PF driver
through mailbox, further causes failure when mapping interrupt and
queues.
hw->num_msi = (num_msi > hw->tqps_num + 1) ? hw->tqps_num + 1 : num_msi;
We need to use hw->tqp_num after it is correctly assigned.
On the other hand, because the private variable named hw->num_msi, which
represents the number of MSI-x interrupt of hns3 PF/VF device, is used in
the '.get_reg' ops implementation function to dump all interrupt related
registers, it should be obtained from firmware directly and we'd better
not modify it in the driver.
Fixes: ef2e785c36cf ("net/hns3: fix Tx interrupt when enabling Rx interrupt")
Fixes: 02a7b55657b2 ("net/hns3: support Rx interrupt")
Cc: stable@dpdk.org
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Hao Chen <chenhao164@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
In current version, when upper level application calls the
rte_eth_dev_configure API function, if pvid config is not set of the
input parameter which struct type is rte_eth_conf, hns3 pmd driver also
sets the VLAN pvid related configuration to hardware, and this is not
reasonable. For example, As pvid is set to 100 by
rte_eth_dev_set_vlan_pvid, when pvid config is not set in rte_eth_conf,
rte_eth_dev_configure will tell driver to delete pvid 0, and that is
meaningless.
This patch fixes it to ensure that driver does not set VLAN pvid related
configuration to hardware when pvid config is not set in rte_eth_conf.
Fixes: 411d23b9eafb ("net/hns3: support VLAN")
Cc: stable@dpdk.org
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
The hns3 network engine is built-in multiple SoCs, such as kunpeng 920,
kunpeng 930, etc. The PCI revision id is 0x21 in kunpeng 920, and the PCI
revision id is 0x30 in kunpeng 930.
This patch gets PCI revision to identify different version of hardware
network engine.
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Here adds some prints for return value when the relative function fails
and enter the exception branch.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
When upper level application calls the rte_eth_tx_burst API function to
send multiple packets at a time with burst mode based on hns3 network
engine, there are some abnormal conditions that cause the driver to fail
to operate the hardware to send packets correctly.
This patch adds some statistic counts for the abnormal errors of Tx data
path to the extend device statistics. The upper level application can
get them by calling the rte_eth_xstats_get API function.
Note: When using burst mode to call the rte_eth_tx_burst API function to
send multiple packets at a time. When the first abnormal error is
detected, add one to the relevant error statistics item, and then exit
the loop of sending multiple packets of the function. That is to say,
even if there are multiple packets in which abnormal errors may be
detected in the burst, the relevant error statistics in the driver will
only be increased by one.
The detail description of the Tx abnormal errors statistic items as
below:
- TX_OVER_LENGTH_PKT_CNT Total number of greater than
HNS3_MAX_FRAME_LEN the driver supported.
- TX_EXCEED_LIMITED_BD_PKT_CNT
Total number of exceeding the hardware limited bd which process a
packet needed bd numbers.
- TX_EXCEED_LIMITED_BD_PKT_REASSEMBLE_FAIL_CNT
Total number of exceeding the hardware limited bd fail which
process a packet needed bd numbers and reassemble fail.
- TX_UNSUPPORTED_TUNNEL_PKT_CNT
Total number of unsupported tunnel packet. The unsupported tunnel
type: vxlan_gpe, gtp, ipip and MPLSINUDP, MPLSINUDP is a packet
with MPLS-in-UDP RFC 7510 header.
- TX_QUEUE_FULL_CNT
Total count which the available bd numbers in current bd queue is
less than the bd numbers with the pkt process needed.
- TX_SHORT_PKT_PAD_FAIL_CNT
Total count which the packet length is less than minimum packet
size HNS3_MIN_PKT_SIZE and fail to be appended with 0.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Hao Chen <chenhao164@huawei.com>
For sending request messages to data plane threads, the
caller invokes thread_msg_send_recv() function which never
returns null response. Thus, removed redundant check on
the returned response.
Coverity issue: 357717, 357772
Fixes: 70709c78fda6 ("net/softnic: add command to enable/disable pipeline")
Cc: stable@dpdk.org
Signed-off-by: Jasvinder Singh <jasvinder.singh@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Make local MCDI helper functions static.
Fixes: f0bda0cd680d ("net/sfc/base: add MCDI wrappers for vPort and vSwitch in EVB")
Fixes: ea94d14dbea0 ("net/sfc/base: provide APIs to configure and reset vPort")
Cc: stable@dpdk.org
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
The maximal supported header modifications number of a single modify
context on the root table cannot be queried from firmware directly.
It is a fixed value of 16 in the latest releases. In the validation
stage, PMD driver should ensure that no more than 16 header modify
actions exist in a single context.
In some old firmware releases, the supported value is 8. PMD driver
should try its best to create the flow. Firmware will return error
and refuse to create the flow if the actions number exceeds the
maximal value.
Fixes: 72a944dba163 ("net/mlx5: fix header modify action validation")
Cc: stable@dpdk.org
Signed-off-by: Bing Zhao <bingz@mellanox.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@mellanox.com>
Currently, the indexed memory pool bitmap start address is not aligned
to cacheline size explicitly. The bitmap initialization requires the
address should be cacheline aligned. In that case, the initialization
maybe failed if the address is not cacheline aligned.
Add RTE_CACHE_LINE_ROUNDUP() to the trunk size calculation to make sure
the bitmap offset address will start with cacheline aligned.
Fixes: a3cf59f56c47 ("net/mlx5: add indexed memory pool")
Signed-off-by: Suanming Mou <suanmingm@mellanox.com>
Tested-by: Lijian Zhang <lijian.zhang@arm.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@mellanox.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
The assert that checks if there is a enough room for the
whole packet minus headroom data is written incorrectly.
The check should be negated in order to work properly.
Fixes: bd0d5930bf56 ("net/mlx5: enable MPRQ multi-stride operations")
Signed-off-by: Alexander Kozyrev <akozyrev@mellanox.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@mellanox.com>
The assert in dynamic flow metadata handling is wrong after the
fix for the performance degradation. The assert meant to check
the metadata mask but was updated with the metadata offset instead.
Fix this assert and restore proper metadata mask checking.
Fixes: 6c55b622a956 ("net/mlx5: set dynamic flow metadata in Rx queues")
Cc: stable@dpdk.org
Signed-off-by: Alexander Kozyrev <akozyrev@mellanox.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@mellanox.com>
Rewrite vectorized path selection logic. Default setting comes from
vectorized devarg, then checks each criteria.
Packed ring vectorized path need:
AVX512F and required extensions are supported by compiler and host
VERSION_1 and IN_ORDER features are negotiated
mergeable feature is not negotiated
LRO offloading is disabled
Split ring vectorized rx path need:
mergeable and IN_ORDER features are not negotiated
LRO, chksum and vlan strip offloadings are disabled
Signed-off-by: Marvin Liu <yong.liu@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Optimize packed ring Tx path like Rx path. Split Tx path into batch and
single Tx functions. Batch function is further optimized by AVX512
instructions.
Signed-off-by: Marvin Liu <yong.liu@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Optimize packed ring Rx path with SIMD instructions. Solution of
optimization is pretty like vhost, is that split path into batch and
single functions. Batch function is further optimized by AVX512
instructions.
Signed-off-by: Marvin Liu <yong.liu@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Move offload, xmit cleanup and packed xmit enqueue function to header
file. These functions will be reused by packed ring vectorized path.
Signed-off-by: Marvin Liu <yong.liu@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Add new devarg for virtio user device vectorized path selection.
By default vectorized path is disabled.
Signed-off-by: Marvin Liu <yong.liu@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Previously, virtio split ring vectorized path was enabled by default.
This is not suitable for everyone because that path does not follow
virtio spec. Add new devarg for virtio vectorized path selection. By
default vectorized path is disabled.
Signed-off-by: Marvin Liu <yong.liu@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Ring initialization is different when inorder feature negotiated. This
action should dependent on negotiated feature bits.
Signed-off-by: Marvin Liu <yong.liu@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Introduce free threshold setting in Rx queue, its default value is 32.
Limit the threshold size to multiple of four as only vectorized packed
Rx function will utilize it. Virtio driver will rearm Rx queue when
more than rx_free_thresh descs were dequeued.
Signed-off-by: Marvin Liu <yong.liu@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Currently, while creating the flow with meter, meter id is saved to the
rte flow. While destroying the flow, the meter object will be found by
the meter id, so the meter object will be released accordingly. But as
the meter id is configured by user, while the meter id is set to 0, it
doesn't make any sense to flow destroy since 0 means flow doesn't have
meter. The meter object with id 0 will be leaked.
As meter object is allocated from indexed memory, and the index starts
from 1, save the internal generated index instead of user defined meter
id will never meet the issue as above.
This patch saves meter index instead of meter id in rte flow.
Signed-off-by: Suanming Mou <suanmingm@mellanox.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@mellanox.com>
The asserts makes sure that 'i' doesn't exceed the expected value.
This to prevent an out of bound access to dbr_bitmap.
The current location of the assert protects the assignment of
dbr_bitmap, but not the access to it.
Moved the assert to the correct place, to protect both cases.
Also, used an existing define for the assert.
Fixes: 21cae8580fd0 ("net/mlx5: allocate door-bells via DevX")
Cc: stable@dpdk.org
Signed-off-by: Asaf Penso <asafp@mellanox.com>
Reviewed-by: Dekel Peled <dekelp@mellanox.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@mellanox.com>
The output flow error parameter is used to indicate the detailed
reason of the failure when calling a rte_flow_* interface. Even
though sometimes the application will not check it or use it, the PMD
must fill it in the failure branch before returning. Or else, some
dirty value in the stack, heap will be accessed as a pointer and then
cause a crash.
In this case, when a port is stopped, it is not allowed to insert a
flow from application. The detailed error information should be
filled. If the application needs to check the detailed error reason,
it will get the information but not result in any crash.
Fixes: 40b9e7f65fe1 ("net/mlx5: check device status before creating flow")
Signed-off-by: Bing Zhao <bingz@mellanox.com>
Acked-by: Ori Kam <orika@mellanox.com>
After inserting an offload flow, the software flag information will
be updated based on the flow. When receiving a packet on this queue,
the hardware packet type bits and the software flag will be used
together to get the inner packet and tunnel header type (if any) from
the global packet type table.
When destroying a flow, the corresponding Rx queue flag needs to be
updated. All flags should be cleared when closing a device because
all control flows and application flows are invalid anymore.
Such behavior is missed when implementing the non-cached mode.
Fixes: 8db7e3b69822 ("net/mlx5: change operations for non-cached flows")
Signed-off-by: Bing Zhao <bingz@mellanox.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@mellanox.com>
1. ln_en bit should not be turned on, since we only support Rx VEB.
2. lan_en bit need to be turned on for a DCF switch rule, otherwise
any Tx packet that hit on a rule will be dropped.
Fixes: fed0c5ca5f19 ("net/ice/base: support programming a new switch recipe")
Cc: stable@dpdk.org
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Acked-by: Qiming Yang <qiming.yang@intel.com>
After VF reset, FDIR rule still takes effect. To solve the issue,
this patch adds to flush all flows before flow uninit. VIRTCHNL
sends message to PF by Admin Queue, so flow flush should be implemented
before Admin Queue shut down.
Fixes: ff2d0c345c3b ("net/iavf: support generic flow API")
Signed-off-by: Simei Su <simei.su@intel.com>
Acked-by: Xiaolong Ye <xiaolong.ye@intel.com>
When we flush FDIR filter, we can not call i40e_fdir_teardown()
function as it will free vsi used for FDIR, then the vsi->base_queue
will be freed from pf->qp_pool, but vsi->base_queue can only get
once when do dev init in i40e_pf_setup(). If we free it, it will
never be alloc again.
Bugzilla ID: 404
Fixes: 2e67a7fbf3ff ("net/i40e: config flow director automatically")
Cc: stable@dpdk.org
Signed-off-by: Wei Zhao <wei.zhao1@intel.com>
Acked-by: Beilei Xing <beilei.xing@intel.com>
Currently, flow "pattern eth type is 0x0806 / end actions mark id
0x86 / rss / end" can't be created successfully. FDIR parser
shouldn't deny RTE_ETHER_TYPE_ARP since ARP packets will be
parsed as PCTYPE_L2_PAYLOAD. This patch fixes the issue.
Bugzilla ID: 402
Fixes: 42044b69c67d ("net/i40e: support input set selection for FDIR")
Cc: stable@dpdk.org
Signed-off-by: Wei Zhao <wei.zhao1@intel.com>
Acked-by: Beilei Xing <beilei.xing@intel.com>
Ideally a rule with "TO VSI LIST" action should not be deleted when one
of the VF reset happens. The correct action by kernel PF driver is to
remove the VSI of a reset VF from the VSI list, but this is not
implemented in kernel PF yet, so workaround is the DCF to prevent a
rule with "To VSI List" action happens.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Reviewed-by: Wei Zhao <wei.zhao1@intel.com>
Updated the params list to include flush timer, this will
allow users to set the HW flush timer value in 10th of second.
Setting 0 will disable the pending cache flush feature.
Signed-off-by: Shahaji Bhosle <sbhosle@broadcom.com>
Signed-off-by: Randy Schacher <stuart.schacher@broadcom.com>
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Reviewed-by: Mike Baucom <michael.baucom@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
The ulp required to be changed to properly call the index table
management routines and use the index for external memory indices.
The ulp no longer has to account for stride as the tf_core returns the
actual offset, not a 0 based index.
Signed-off-by: Mike Baucom <michael.baucom@broadcom.com>
Reviewed-by: Kishore Padmanabha <kishore.padmanabha@broadcom.com>
Reviewed-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
- Added support variable sized action records
- Additional error checking on table scope params
- Single external pool supported per direction
- Changed to return action record pointer
- Allows action pool to fully utilize the number of flows
Signed-off-by: Farah Smith <farah.smith@broadcom.com>
Signed-off-by: Mike Baucom <michael.baucom@broadcom.com>
Reviewed-by: Peter Spreadborough <peter.spreadborough@broadcom.com>
Reviewed-by: Kishore Padmanabha <kishore.padmanabha@broadcom.com>
The resource function did not have a method of invalidating or
indicating that a resource is uninitialized. Added an invalid enum so
that processing works correctly for partially added flows.
Signed-off-by: Mike Baucom <michael.baucom@broadcom.com>
Reviewed-by: Kishore Padmanabha <kishore.padmanabha@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Max Rx Ring count could be < Max stat contexts. While accounting
for stat contexts, this should be also considered and
the max ring count adjusted accordingly.
Fixes: f03e66cb64ce ("net/bnxt: limit queue count for NS3/Stingray devices")
Cc: stable@dpdk.org
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
The AltiVec header file breaks boolean type. [1] [2]
Currently the workaround was located only in mlx5 device.
Adding the trace module caused this issue to appear again, due to
order of includes, it keeps overriding the local fix.
This patch solves this issue by resetting the bool type, immediately
after it is being changed.
[1] https://mails.dpdk.org/archives/dev/2018-August/110281.html
[2]
In file included from
dpdk/ppc_64-power8-linux-gcc/include/rte_mempool_trace_fp.h:18:0,
from
dpdk/ppc_64-power8-linux-gcc/include/rte_mempool.h:54,
from
dpdk/drivers/common/mlx5/mlx5_common_mr.c:7:
dpdk/ppc_64-power8-linux-gcc/include/rte_trace_point.h: In
function '__rte_trace_point_fp_is_enabled':
dpdk/ppc_64-power8-linux-gcc/include/rte_trace_point.h:226:2:
error: incompatible types when returning type 'int' but '__vector __bool
int' was expected
return false;
^
In file included from
dpdk/ppc_64-power8-linux-gcc/include/rte_trace_point.h:281:0,
from
dpdk/ppc_64-power8-linux-gcc/include/rte_mempool_trace_fp.h:18,
from
dpdk/ppc_64-power8-linux-gcc/include/rte_mempool.h:54,
from
dpdk/drivers/common/mlx5/mlx5_common_mr.c:7:
dpdk/ppc_64-power8-linux-gcc/include/rte_mempool_trace_fp.h:
In function 'rte_mempool_trace_ops_dequeue_bulk':
dpdk/ppc_64-power8-linux-gcc/include/rte_trace_point_provider.h:104:6:
error: wrong type argument to unary exclamation mark
if (!__rte_trace_point_fp_is_enabled()) \
^
dpdk/ppc_64-power8-linux-gcc/include/rte_trace_point.h:49:2:
note: in expansion of macro '__rte_trace_point_emit_header_fp'
__rte_trace_point_emit_header_##_mode(&__##_tp); \
^
dpdk/ppc_64-power8-linux-gcc/include/rte_trace_point.h:99:2:
note: in expansion of macro '__RTE_TRACE_POINT'
__RTE_TRACE_POINT(fp, tp, args, __VA_ARGS__)
^
dpdk/ppc_64-power8-linux-gcc/include/rte_mempool_trace_fp.h:20:1:
note: in expansion of macro 'RTE_TRACE_POINT_FP'
RTE_TRACE_POINT_FP(
^
dpdk/ppc_64-power8-linux-gcc/include/rte_mempool_trace_fp.h:
In function 'rte_mempool_trace_ops_dequeue_contig_blocks':
dpdk/ppc_64-power8-linux-gcc/include/rte_trace_point_provider.h:104:6:
error: wrong type argument to unary exclamation mark
if (!__rte_trace_point_fp_is_enabled()) \
^
dpdk/ppc_64-power8-linux-gcc/include/rte_trace_point.h:49:2:
note: in expansion of macro '__rte_trace_point_emit_header_fp'
__rte_trace_point_emit_header_##_mode(&__##_tp); \
^
dpdk/ppc_64-power8-linux-gcc/include/rte_trace_point.h:99:2:
note: in expansion of macro '__RTE_TRACE_POINT'
__RTE_TRACE_POINT(fp, tp, args, __VA_ARGS__)
^
dpdk/ppc_64-power8-linux-gcc/include/rte_mempool_trace_fp.h:29:1:
note: in expansion of macro 'RTE_TRACE_POINT_FP'
RTE_TRACE_POINT_FP(
^
dpdk/ppc_64-power8-linux-gcc/include/rte_mempool_trace_fp.h:
In function 'rte_mempool_trace_ops_enqueue_bulk':
dpdk/ppc_64-power8-linux-gcc/include/rte_trace_point_provider.h:104:6:
error: wrong type argument to unary exclamation mark
if (!__rte_trace_point_fp_is_enabled()) \
Fixes: 725f5dd0bfb5 ("net/mlx5: fix build on PPC64")
Signed-off-by: Ori Kam <orika@mellanox.com>
Signed-off-by: David Christensen <drc@linux.vnet.ibm.com>
Tested-by: David Christensen <drc@linux.vnet.ibm.com>
Tested-by: Raslan Darawsheh <rasland@mellanox.com>
Acked-by: Matan Azrad <matan@mellanox.com>
gcc 10.0.1 reports:
../drivers/net/avp/avp_ethdev.c: In function ‘avp_xmit_scattered_pkts’:
../drivers/net/avp/avp_ethdev.c:1791:24:
warning: ‘avp_bufs[count]’ may be used uninitialized in this function
[-Wmaybe-uninitialized]
1791 | tx_bufs[i] = avp_bufs[count];
| ~~~~~~~~^~~~~~~
../drivers/net/avp/avp_ethdev.c:1791:24:
warning: ‘avp_bufs[count]’ may be used uninitialized in this function
[-Wmaybe-uninitialized]
Fix by initializing the array.
Fixes: 295abce2d25b ("net/avp: add packet transmit functions")
Cc: stable@dpdk.org
Signed-off-by: Kevin Traynor <ktraynor@redhat.com>
Acked-by: Steven Webster <steven.webster@windriver.com>
Change references to ABI 20.0.1 to use ABI v21, see
https://doc.dpdk.org/guides/contributing/abi_policy.html#general-guidelines
"Major ABI versions are declared no more frequently than yearly.
Compatibility with the major ABI version is mandatory in subsequent
releases until a new major ABI version is declared."
Combined ABI policy and versioning in maintainers, add map files to the
filter to more closely monitor future ABI changes.
Signed-off-by: Ray Kinsella <mdr@ashroe.eu>
bnxt_free_one_vnic and bnxt_setup_one_vnic are called on configuring
port vlan stripping. bnxt_setup_one_vnic keeps incrementing the
vnic rx_queue_cnt. Fix to reset vnic rx_queue_cnt in bnxt_free_one_vnic.
Fixes: cfadfee41ed1 ("net/bnxt: fix VLAN strip")
Cc: stable@dpdk.org
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
During port 0 rxq 1 start ie queue start,
bnxt_free_hwrm_rx_ring() we are clearing the pointers to mbuf array.
Due to this we overwrite the queue with fresh mbuf allocations
causing previously allocated mbufs to leak.
Add a check before allocating mbuf to replenish only empty mbuf slots
in the RxQ.
Fixes: 2eb53b134aae ("net/bnxt: add initial Rx code")
Cc: stable@dpdk.org
Signed-off-by: Rahul Gupta <rahul.gupta@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
HWRM_PORT_MAC_QCFG is not supported on a VF. Added a PF check
in bnxt_hwrm_port_mac_qcfg() to prevent the probe failure on a VF.
Fixes: f6e250d21ab0 ("net/bnxt: fetch SVIF information from firmware")
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Firmware reports any fatal error (either ASIC or Firmware related) via a
new status register. This status register can provide more detailed
information about the firmware errors, especially if error occurs before
HWRM_VER_GET is issued. Attempt to map this register if it is present
and check for firmware status when VER_GET command fails.
Refactored the code to allocate the "bp->recovery_info" structure
in bnxt_init_fw() instead of doing in bnxt_hwrm_error_recovery_qcfg().
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Driver destroys the vnic when the port is brought down.
When user tries to add a vlan when port is stopped, driver
issues HWRM command to FW with invalid vnic_id and it fails.
Fixed to return an error while setting vlan when port is
not started.
Fixes: b4e190d55c25 ("net/bnxt: fix MAC/VLAN filter allocation")
Cc: stable@dpdk.org
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Fixed to invoke clean up in the reverse sequence of
initialization in case any of the FW commands fail
during port start.
Fixes: 0b533591238f ("net/bnxt: inform firmware about IF state changes")
Cc: stable@dpdk.org
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
FW returns HWRM_ERR_CODE_HOT_RESET_PROGRESS(0xa) when it is
unable to process a specific cmd while hot reset is in progress.
Host driver is expected to keep retrying the cmd for 2s with
a gap of 50ms between each retrial.
Also, fixed to fail port start if the HWRM_FUNC_DRV_IF_CHANGE
still returns error after 2 seconds.
Fixes: 0b533591238f ("net/bnxt: inform firmware about IF state changes")
Cc: stable@dpdk.org
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Lance Richardson <lance.richardson@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Added information about supported speeds for the port in the
"dev_infos_get". As other PMDs are returning the speed capabilities,
apps may expect this behavior from bnxt PMD.
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
