These are the defaults for the packet buffer size registers that need to
be explicitly set back if someone changes them and comes back to a normal
driver.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch is for the following updates to the K1 configurations:
Tx idle period for entering K1 should be 128 ns.
Minimum Tx idle period in K1 should be 256 ns.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
In case that auto-negotiate is not enabled, call
e1000_setup_copper_link_generic instead of e1000_phy_setup_autoneg.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
e1000_check_for_link_media_swap() is supposed to check PHY page 0 for
copper and PHY page 1 for "other" (fiber) link. We switched back from
page 1 to page 0 too soon, before e1000_check_for_link_82575() is
executed and we were never finding link on fiber (other).
Note: The precedence of link type is controlled by the PHY settings.
If the link is copper, as the M88E1112 page address is set to 1, it should be
set back to 0 before checking this link.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Fix for I217 Packet Loss issue - The Management Engine sets the FEXTNVM4
Beacon Duration incorrectly. This fix ensures that the correct value will
always be set. Correct value for this field is 8 usec.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
TIPG value is increased when setting speed to 10 half to prevent
packet loss. However, it was never decreased again when speed
changes. This caused performance issues in the NDIS driver.
Fix this to restore TIPG to default value on non 10 half.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
For DH89XXCC_SGMII, write flush leaves registers of this device trashed
(0xFFFFFFFF). Added check for this device.
Also, after both for Port SW Reset and Device Reset case, platform should
wait at least 3ms before reading any registers. Since waiting is
conditionally executed only for Device Reset - removed the condition.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
The i210 has two EEPROM access registers that are located in
non-standard offsets: EEARBC and EEMNGCTL. EEARBC was fixed previously
and EEMNGCTL should also be corrected.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
The wrong bit is being used in PHYREG16 for PHY power down. In addition,
the use of PHYREG 16 is unnecessary if bit 11 of PHYREG 0 is used.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This is a patch to change the value of register 776.20[11:2] for jumbo
mode from 0x1A to 0x1F. This is to enlarge the gap between read and
write pointers in the TX Fifo.
And replace the magic number with a macro by the way.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Several customers have reported a link flap issue on 82579. The symptoms
are random and intermittent link losses when 82579 is connected to specific
switches. Issue has been root caused as interoperability problem between
the NIC and at least some Broadcom PHYs in the Energy Efficient Ethernet
wake mechanism.
To fix the issue, we are disabling the Phase Locked Loop shutdown in 100M
Low Power Idle. This solution will cause an increase of power in 100M EEE
link. It may cost additional 28mW in this specific mode.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Add u32 return value to function e1000_resume_workarounds_pchlan,
so that calling function can detect PHY access failure during resuming
flow.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Adding code where missing to handle case where calls to
e1000_read_kmrn_reg_80003es2lan and e1000_write_kmrn_reg_80003es2lan return
an error value.
Also, when accessing the E1000_KMRNCTRLSTA_INBAND_PARAM offset to disable
far-end loopback on 80003es2lan devices, make the handling of a read or
write failure consistent between hw_init and hw_reset.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Adding code to a case where e1000_nvn_read is called, but there is no
consideration for when the read fails (returns an error code).
Also, this patch adds an error message to a base NVM reading function that
is missing it for consistency.
This patch is not covering all cases of these conditions, it only covers
the code used by the e1000e driver.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Previously, the rar_set functions were of type void, and when they failed
to program an address register they would, at most, put a message into
the log and end. The fact that they failed to program an address into a
address register, if checked for, should be captured and passed back to
the caller so that the drivers can deal with the situation (or not) as
they deem best.
Drivers can ignore or use the return value. No change to base drivers
is mandated by this change unless a driver wants to handle the failure
to program an address register (e.g. evaluate the return value).
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Although this change should be optimized out by the compiler, just
return a constant directly rather than declare a variable.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
The "FIXME" comment is revomed from e1000_acquire_swfw_sync_80003es2lan
but forgotten being removed from e1000_acquire_swfw_sync_82575 while
the similar changes were made to both.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
The extended unified packet type is now part of the standard ABI.
As mbuf struct is changed, the mbuf library version is incremented.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
The Rx interrupt feature is now part of the standard ABI.
Because of changes in rte_intr_handle and struct rte_eth_conf,
the eal and ethdev library versions are incremented.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
This patch adds a note to the README files in the
drivers/net/pmd/base dirs to highlight that the code should not
be modifed by the user apart from the pmd_osdep.[ch] files.
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Ieee1588 reads system time to set its timestamp. On 1G NICs, for example,
i350, system time is disabled by default. It means the ieee1588 timestamp
will always be 0.
This patch enables system time when ieee1588 is enabled.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Header buffer address for header split will be filled with the physical
address for DMA, which is actually not needed at all, as header split
hasn't been supported. Hardware requires the least bit of header address
which is 'Descriptor Done' bit when write back should be set to 0 by driver.
The issue is that if the user wants to reserve an odd number of bytes between
the mbuf header and data buffer, the physical address to be filled in the
descriptor would happen to be odd. That means the DD bit would be set to
non-zero by driver. That will result in reporting descriptor done wrongly.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Some drivers was not following DPDK convention and
was leaving logging always in even if LOG_LEVEL was configured
to disable debug logs.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
[Thomas: apply same fix to i40e, fm10k and bnx2x]
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Any debug messages about hardware should be under debug (or removed)
and reduce customer visible log spam.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
The patch does below for igb PF:
- Setup NIC to generate MSI-X interrupts
- Set the IVAR register to map interrupt causes to vectors
- Implement interrupt enable/disable functions
Signed-off-by: Danny Zhou <danny.zhou@intel.com>
Signed-off-by: Cunming Liang <cunming.liang@intel.com>
This patch enables jumbo frame support for the 82583V.
It has been tested ( rx and tx ) with real HW.
Signed-off-by: Klaus Degner <kd@allegro-packets.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Queues were freed in clear function called in stop function.
Split clearing and freeing in separate functions to
move queue freeing from stop to close function.
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch depends on the Port Hotplug Framework.
It implements the eth_dev_uninit functions for rte_em_pmd,
rte_igb_pmd and rte_igbvf_pmd.
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
add function to support ethtool ops:
- get_reg_length
- get_regs
- get_eeprom_length
- get_eeprom
- set_eeprom
Signed-off-by: Liang-Min Larry Wang <liang-min.wang@intel.com>
Acked-by: Andrew Harvey <agh@cisco.com>
Acked-by: David Harton <dharton@cisco.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
- set_mac_addr
Signed-off-by: Liang-Min Larry Wang <liang-min.wang@intel.com>
Acked-by: Andrew Harvey <agh@cisco.com>
Acked-by: David Harton <dharton@cisco.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Move malloc inside eal and create a new section in MAINTAINERS file for
Memory Allocation in EAL.
Create a dummy malloc library to avoid breaking applications that have
librte_malloc in their DT_NEEDED entries.
This is the first step towards using malloc to allocate memory directly
from memsegs. Thus, memzones would allocate memory through malloc,
allowing to free memzones.
Signed-off-by: Sergio Gonzalez Monroy <sergio.gonzalez.monroy@intel.com>
To unify packet types among all PMDs, bit masks of packet type for
'ol_flags' are replaced by unified packet type.
To avoid breaking ABI compatibility, all the changes would be
enabled by RTE_NEXT_ABI.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Add e1000/igb support for new ethdev APIs to enable and read
IEEE1588 PTP timestamps.
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
To support querying hash key size per port, an new field of
'hash_key_size' was added in 'struct rte_eth_dev_info' for storing
hash key size in bytes.
The correct hash key size in bytes should be filled into the
'struct rte_eth_dev_info', to support querying it.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The parameter tx_free_thresh is not consistent between the drivers:
some use it as rte_eth_tx_burst() requires, some release buffers when
the number of free descriptors drop below this value.
Let's use it as most fast-path code does, which is the latter, and update
comments throughout the code to reflect that.
Signed-off-by: Zoltan Kiss <zoltan.kiss@linaro.org>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Upcoming drivers will need to be able to support other bus types.
This is a transparent change to how struct eth_driver is initialized.
It has not function or ABI layout impact, but makes adding a later
bus type (Xen, Hyper-V, ...) much easier.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Move e1000 pmd to drivers/net directory
As part of move, rename "e1000" subdirectory, which contains the code
from the "base driver", to "base".
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
