Add support for forced ethernet speed setting.
Currently testpmd tries to configure the Ethernet port in autoneg mode.
It is not possible to set the Ethernet port to a specific speed while
starting testpmd. In some cases capability to configure a forced speed
for the Ethernet port during initialization may be necessary. This patch
tries to add this support.
The patch assumes full duplex setting and does not attempt to change that.
So speeds like 10M, 100M are not configurable using this method.
The command line to configure a forced speed of 10G:
dpdk-testpmd -c 0xff -- -i --eth-link-speed 10000
The command line to configure a forced speed of 50G:
dpdk-testpmd -c 0xff -- -i --eth-link-speed 50000
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Rename PKT_RX_EIP_CKSUM_BAD to PKT_RX_OUTER_IP_CKSUM_BAD and
deprecate the original name. The new name is better aligned
with existing PKT_RX_OUTER_* flags, which should help reduce
confusion about its use.
Suggested-by: Ferruh Yigit <ferruh.yigit@intel.com>
Signed-off-by: Lance Richardson <lance.richardson@broadcom.com>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
cmd_tunnel_udp_config checked 'cmd' to set prot_type but this cmd is
only for rx_vxlan_port. The unnecessary cmd check will cause uninit
coverity issue. So remove it and rename 'cmd' to 'rx_vxlan_port'.
Coverity issue: 366155
Fixes: bd948f20d6 ("app/testpmd: VXLAN packet identification")
Cc: stable@dpdk.org
Signed-off-by: Xiaoyun Li <xiaoyun.li@intel.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
"show port cap all|<port_id>" was to display offload configuration of
port(s).
But later two other commands added to show same information in more
accurate way:
show port (port_id) rx_offload configuration
show port (port_id) tx_offload configuration
These new commands can both show port and queue level configuration,
also with their capabilities counterparts easier to see offload
capability and configuration of the port in similar syntax.
So the functionality is duplicated and removing this version, to favor
the new commands.
Another problem with this command is it requires each new offload to be
added into the function to display them, and there were missing offloads
that are not displayed, this requirement for sure will create gaps by
time as new offloads added.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Lance Richardson <lance.richardson@broadcom.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
The tx_queue member of the fwd_lcore struct is unused as it is already
part of the fwd_stream structure. Deleting helps improve code readability.
Signed-off-by: Kathleen Capella <kathleen.capella@arm.com>
Reviewed-by: Honnappa Nagarahalli <honnappa.nagarahalli@arm.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Add support for displaying the count of used (filled by hardware
but not yet processed by the driver) descriptors on a receive
queue in order to allow the rte_eth_dev rx_queue_count() API to
be exercised and tested.
Signed-off-by: Lance Richardson <lance.richardson@broadcom.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
Parts of the unit tests code rely on forked/secondary processes
(expectedly) failing.
A crash in those situations could be missed so add a check on coredumps
presence after unit tests have run.
When unit tests fail, it can also help checking for coredumps as it
could give more insights on what happened.
In some situations (like explicit call to rte_panic), coredump generation
must be disabled to avoid false positives.
Cc: stable@dpdk.org
Signed-off-by: David Marchand <david.marchand@redhat.com>
Acked-by: Luca Boccassi <bluca@debian.org>
Acked-by: Aaron Conole <aconole@redhat.com>
Currently external memory test uses 4K page size.
VFIO DMA mapping works only with system page granularity.
Earlier it was working because all the contiguous mappings
were coalesced and mapped in one-go which ended up becoming
a lot bigger page. Now that VFIO DMA mappings both in IOVA as VA
and IOVA as PA mode, are being done at memseg list granularity,
we need to use system page size.
Fixes: b270daa43b ("test: support external memory")
Cc: stable@dpdk.org
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Acked-by: Anatoly Burakov <anatoly.burakov@intel.com>
The crypto perf graphing script did not handle parsing parameters
from the JSON config files correctly.
A common parsing function is used for both EAL and app parameters,
to ensure they are handled the same way and to reduce code duplication.
Short parameters are now passed with the value being a second argument,
rather than as one argument with dividing space.
Long parameters with no expected value are supported for EAL now also.
e.g. "--no-huge" can be added to config as "no-huge": true
Fixes: f400e0b82b ("app/crypto-perf: add script to graph perf results")
Signed-off-by: Ciara Power <ciara.power@intel.com>
Acked-by: Adam Dybkowski <adamx.dybkowski@intel.com>
Some platforms may not support operations on encrypted digest,
So in this patch adding a check for such test cases.
Signed-off-by: Gagandeep Singh <g.singh@nxp.com>
Acked-by: Akhil Goyal <akhil.goyal@nxp.com>
Shared age action query was implemented as part of flow query,
but was not implemented as part of shared action query.
This patch adds the required implementation.
Fixes: 2f622174bf ("app/testpmd: support query of age action")
Cc: stable@dpdk.org
Signed-off-by: Dekel Peled <dekelp@nvidia.com>
Acked-by: Matan Azrad <matan@nvidia.com>
Add support to specify PF or VF as targets in "set sample_actions"
command.
Signed-off-by: Satheesh Paul <psatheesh@marvell.com>
Acked-by: Ori Kam <orika@nvidia.com>
There is the "set rxpkts" command in the testpmd interactive mode,
it configures the segment sizes to split the packet on receiving.
The mentioned segment sizes are provided on the Rx queue setup
as part of queue configuration. Hence, to take the rxpkts command
into effect the Rx queues must be explicitly reconfigured.
The explained above is related to the "set rxoffs" as well.
The patch sets the queue reconfiguration request flag for
all devices once Rx split settings are updated, to take
the changes into effect the port(s) should be restarted.
Fixes: 0f2096d7ab ("app/testpmd: add rxpkts commands and parameters")
Fixes: 91c78e090e ("app/testpmd: add rxoffs commands and parameters")
Cc: stable@dpdk.org
Signed-off-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
In interactive mode, if testpmd exit by calling rte_exit without
restore terminal attributes, terminal will not echo keyboard input.
register a function with atexit() in prompt(), when exit() in
rte_exit() is called, the registered function restores terminal
attributes.
Fixes: 5a8fb55c48 ("app/testpmd: support unidirectional configuration")
Cc: stable@dpdk.org
Signed-off-by: Dapeng Yu <dapengx.yu@intel.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
When testing high performance numbers, it is often that CPU performance
limits the max values device can reach (both in pps and in gbps)
Here instead of recreating each packet separately, we use clones counter
to resend the same mbuf to the line multiple times.
PMDs handle that transparently due to reference counting inside of mbuf.
Reaching max PPS on small packet sizes helps here:
Some data from our 2 port x 50G device. Using 2*6 tx queues, 64b packets,
PowerEdge R7525, AMD EPYC 7452:
./build/app/dpdk-testpmd -l 32-63 -- --forward-mode=flowgen \
--rxq=6 --txq=6 --disable-crc-strip --burst=512 \
--flowgen-clones=0 --txd=4096 --stats-period=1 --txpkts=64
Gives ~46MPPS TX output:
Tx-pps: 22926849 Tx-bps: 11738590176
Tx-pps: 23642629 Tx-bps: 12105024112
Setting flowgen-clones to 512 pushes TX almost to our device
physical limit (68MPPS) using same 2*6 queues(cores):
Tx-pps: 34357556 Tx-bps: 17591073696
Tx-pps: 34353211 Tx-bps: 17588802640
Doing similar measurements per core, I see one core can do
6.9MPPS (without clones) vs 11MPPS (with clones)
Verified on Marvell qede and atlantic PMDs.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
"port config all max-pkt-len" command fails because it doesn't set the
'DEV_RX_OFFLOAD_JUMBO_FRAME' offload flag properly.
Commit in the fixes line moved the 'DEV_RX_OFFLOAD_JUMBO_FRAME' offload
flag update from 'cmd_config_max_pkt_len_parsed()' to 'init_config()'.
'init_config()' function is only called during testpmd startup, but the
flag status needs to be calculated whenever 'max_rx_pkt_len' changes.
The issue can be reproduced as [1], where the 'max-pkt-len' reduced and
'DEV_RX_OFFLOAD_JUMBO_FRAME' offload flag should be cleared but it
didn't.
Adding the 'update_jumbo_frame_offload()' helper function to update
'DEV_RX_OFFLOAD_JUMBO_FRAME' offload flag and 'max_rx_pkt_len'. This
function is called both by 'init_config()' and
'cmd_config_max_pkt_len_parsed()'.
Default 'max-pkt-len' value set to zero, 'update_jumbo_frame_offload()'
updates it to "RTE_ETHER_MTU + PMD specific Ethernet overhead" when it
is zero.
If '--max-pkt-len=N' argument provided, it will be used instead.
And with each "port config all max-pkt-len" command, the
'DEV_RX_OFFLOAD_JUMBO_FRAME' offload flag, 'max-pkt-len' and MTU is
updated.
[1]
--------------------------------------------------------------------------
dpdk-testpmd -c 0xf -n 4 -- -i --max-pkt-len=9000 --tx-offloads=0x8000
--rxq=4 --txq=4 --disable-rss
testpmd> set verbose 3
testpmd> port stop all
testpmd> port config all max-pkt-len 1518
testpmd> port start all
// Got fail error info without this patch
Configuring Port 0 (socket 1)
Ethdev port_id=0 rx_queue_id=0, new added offloads 0x800 must be
within per-queue offload capabilities 0x0 in rte_eth_rx_queue_setup()
Fail to configure port 0 rx queues //<-- Fail error info;
--------------------------------------------------------------------------
Bugzilla ID: 625
Fixes: 761c4d6690 ("app/testpmd: fix max Rx packet length for VLAN packets")
Cc: stable@dpdk.org
Signed-off-by: Steve Yang <stevex.yang@intel.com>
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Lance Richardson <lance.richardson@broadcom.com>
Acked-by: Wisam Jaddo <wisamm@nvidia.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
Tested-by: Bo Chen <box.c.chen@intel.com>
When the RSS with null key was set in sample actions list, it
caused the segmentation fault since the RSS key pointer was
NULL while did the memory copy.
This patch adds the RSS key NULL pointer checking before copying
to fix the segmentation fault issue.
Fixes: 11b1b0edda ("app/testpmd: support RSS in sample action")
Signed-off-by: Jiawei Wang <jiaweiw@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
This patch defines new RSS offload types for MPLS. The distribution
will on the basis of MPLS tag.
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
IPv6 DSCP field ID is missing from the original list of Field IDs
for MODIFY_FIELD action. Add it to support IPv6 header fully.
Add ipv6_dscp option for the corresponding header field in testpmd.
Fixes: 73b68f4c54 ("ethdev: introduce generic modify flow action")
Signed-off-by: Alexander Kozyrev <akozyrev@nvidia.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
Since the patch '1848b117' has initialized the variable 'key' in
'struct rte_flow_action_rss' with 'NULL', the PMD cannot get the
RSS key now. Details as bellow:
testpmd> flow create 0 ingress pattern eth / ipv4 / end actions
rss types ipv4-other end key
1234567890123456789012345678901234567890FFFFFFFFFFFF123
4567890123456789012345678901234567890FFFFFFFFFFFF
queues end / end
Flow rule #1 created
testpmd> show port 0 rss-hash key
RSS functions:
all ipv4-other ip
RSS key:
4439796BB54C5023B675EA5B124F9F30B8A2C03DDFDC4D02A08C9B3
34AF64A4C05C6FA343958D8557D99583AE138C92E81150366
This patch sets offset and size of the 'key' variable as the first
parameter of the token 'key'. Later, the address of the RSS key will
be copied to 'key' variable.
Fixes: 1848b117cc ("app/testpmd: fix RSS key for flow API RSS rule")
Cc: stable@dpdk.org
Signed-off-by: Alvin Zhang <alvinx.zhang@intel.com>
Tested-by: Jun W Zhou <junx.w.zhou@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
When testpmd enabled the verbosity for the received packets, if two
packets were received at the same time, for example, sampling packet and
normal packet, the dump output of these packets may be overlapping due
to multiple core handling the multiple queues simultaneously.
The patch uses one string buffer that collects all the packet dump
output into this buffer and then printouts it at last, that guarantees
to printout separately the dump output per packet.
Fixes: d862c45b59 ("app/testpmd: move dumping packets to a separate function")
Cc: stable@dpdk.org
Signed-off-by: Jiawei Wang <jiaweiw@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
The rte_ethdev_driver.h, rte_ethdev_vdev.h and rte_ethdev_pci.h files are
for drivers only and should be a private to DPDK and not installed.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Steven Webster <steven.webster@windriver.com>
During SA creation, if the required algorithm is not supported,
drivers can return ENOTSUP. But in most of the IPsec test cases,
if the SA creation does not success, it just returns
TEST_FAILED.
This patch fixes this issue by returning the actual return values
from the driver to the application, so that it can make decisions
whether the test case is passed, failed or unsupported.
Fixes: 05fe65eb66 ("test/ipsec: introduce functional test")
Cc: stable@dpdk.org
Signed-off-by: Gagandeep Singh <g.singh@nxp.com>
Acked-by: Akhil Goyal <akhil.goyal@nxp.com>
The python script introduced in this patch runs the crypto performance
test application for various test cases, and graphs the results.
Test cases are defined in config JSON files, this is where parameters
are specified for each test. Currently there are various test cases for
devices crypto_qat, crypto_aesni_mb and crypto_gcm. Tests for the
ptest types Throughput and Latency are supported for each.
The results of each test case are graphed and saved in PDFs (one PDF for
each test suite graph type, with all test cases).
The graphs output include various grouped barcharts for throughput
tests, and histogram and boxplot graphs are used for latency tests.
Documentation is added to outline the configuration and usage for the
script.
Usage:
A JSON config file must be specified when running the script,
"./dpdk-graph-crypto-perf <config_file>"
The script uses the installed app by default (from ninja install).
Alternatively we can pass path to app by
"-f <rel_path>/<build_dir>/app/dpdk-test-crypto-perf"
All device test suites are run by default.
Alternatively we can specify by adding arguments,
"-t latency" - to run latency test suite only
"-t throughput latency"
- to run both throughput and latency test suites
A directory can be specified for all output files,
or the script directory is used by default.
"-o <output_dir>"
To see the output from the dpdk-test-crypto-perf app,
use the verbose option "-v".
Signed-off-by: Ciara Power <ciara.power@intel.com>
Acked-by: Declan Doherty <declan.doherty@intel.com>
Acked-by: Adam Dybkowski <adamx.dybkowski@intel.com>
The csv output for each ptest type used ";" instead of ",".
This has now been fixed to use the comma format that is used in the csv
headers.
Fixes: f6cefe253c ("app/crypto-perf: add range/list of sizes")
Fixes: 96dfeb609b ("app/crypto-perf: add new PMD benchmarking mode")
Fixes: da40ebd6d3 ("app/crypto-perf: display results in test runner")
Cc: stable@dpdk.org
Signed-off-by: Ciara Power <ciara.power@intel.com>
Acked-by: Declan Doherty <declan.doherty@intel.com>
Acked-by: Adam Dybkowski <adamx.dybkowski@intel.com>
The csv output for the latency performance test had an extra header,
"Packet Size", which is a duplicate of "Buffer Size", and had no
corresponding value in the output. This is now removed.
Fixes: f6cefe253c ("app/crypto-perf: add range/list of sizes")
Cc: stable@dpdk.org
Signed-off-by: Ciara Power <ciara.power@intel.com>
Acked-by: Declan Doherty <declan.doherty@intel.com>
Acked-by: Adam Dybkowski <adamx.dybkowski@intel.com>
The symmetric session configure callback function in OCTEON TX2 crypto
PMD returns error if the cipher operation is not set to either encrypt
or decrypt. This patch sets the cipher operation for the null cipher
to encrypt.
Fixes: 7444937523 ("test/event_crypto_adapter: fix configuration")
Cc: stable@dpdk.org
Signed-off-by: Ankur Dwivedi <adwivedi@marvell.com>
Acked-by: Abhinandan Gujjar <abhinandan.gujjar@intel.com>
For the wmb in order_process_stage_1 and order_process_stage_invalid in
the order test, they can be removed. This is because when the test results
are wrong, the worker core writes 'true' to t->err. Then other worker
cores, producer cores and the main core will load the 'error' index and
stop testing. So, for the worker cores, no other storing operation needs
to be guaranteed after this when errors happen.
Signed-off-by: Feifei Wang <feifei.wang2@arm.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Acked-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
For "processed_pkts" function, no operations should keep the order that
being executed before loading "worker[i].processed_pkts".
Signed-off-by: Feifei Wang <feifei.wang2@arm.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Acked-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Simply replace rte_smp barrier with atomic threand fence.
Signed-off-by: Phil Yang <phil.yang@arm.com>
Signed-off-by: Feifei Wang <feifei.wang2@arm.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Acked-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
For "processed_pkts" and "total_latency" functions, no operations should
keep the order that being executed before loading
"worker[i].processed_pkts". Thus rmb is unnecessary before loading.
For "perf_launch_lcores" function, wmb after that the main lcore
updates the variable "t->done", which represents the end of the test
signal, is unnecessary. Because after the main lcore updates this
siginal variable, it will jump out of the launch function loop, and wait
other lcores stop or return error in the main function(evt_main.c).
During this time, there is no important storing operation and thus no
need for wmb.
Signed-off-by: Feifei Wang <feifei.wang2@arm.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Acked-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
This patch fixes RTE SMP barrier bugs for the perf test of eventdev.
For the "perf_process_last_stage" function, wmb after storing
processed_pkts should be moved before it. This is because the worker
lcore should ensure it has really finished data processing, e.g. event
stored into buffers, before the shared variables "w->processed_pkts"are
stored.
For the "perf_process_last_stage_latency", on the one hand, the wmb
should be moved before storing into "w->processed_pkts". The reason is
the same as above. But on the other hand, for "w->latency", wmb is
unnecessary due to data dependency.
Fixes: 2369f73329 ("app/testeventdev: add perf queue worker functions")
Cc: stable@dpdk.org
Signed-off-by: Feifei Wang <feifei.wang2@arm.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Acked-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
For eventdev pipeline test, in burst_tx cases, there is no needed to
set ev.op as RTE_EVENT_OP_RELEASE and call pipeline_event_enqueue_burst
to release events. This is because for tx mode(internal_port=true),
the capability "implicit_release" of dev is enabled, and the app can
release events by "rte_event_dequeue_burst" rather than enqueue.
Fixes: 314bcf58ca ("app/eventdev: add pipeline queue worker functions")
Cc: stable@dpdk.org
Signed-off-by: Feifei Wang <feifei.wang2@arm.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
For the fwd mode (internal_port = false) in pipeline test,
processed-pkts increment should after enqueue. However, in
multi_stage_fwd and multi_stage_burst_fwd, "w->processed_pkts" is
increased before enqueue.
To fix this, move "w->processed_pkts" increment after enqueue, and then
the main core can load the correct number of processed packets.
Fixes: 314bcf58ca ("app/eventdev: add pipeline queue worker functions")
Cc: stable@dpdk.org
Signed-off-by: Feifei Wang <feifei.wang2@arm.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
When testing ring performance in the case that multiple lcores are mapped
to the same physical core, e.g. --lcores '(0-3)@10', it takes a very long
time to wait for the "enqueue_dequeue_bulk_helper" to finish.
This is because too much iteration numbers and extremely low efficiency
for enqueue and dequeue with this kind of core mapping. Following are the
test results to show the above phenomenon:
x86-Intel(R) Xeon(R) Gold 6240:
$sudo ./app/test/dpdk-test --lcores '(0-1)@25'
Testing using two hyperthreads(bulk (size: 8):)
iter_shift: 3 5 7 9 11 13 *15 17 19 21 23
run time: 7s 7s 7s 8s 9s 16s 47s 170s 660s >0.5h >1h
legacy APIs: SP/SC: 37 11 6 40525 40525 40209 40367 40407 40541 NoData NoData
legacy APIs: MP/MC: 56 14 11 50657 40526 40526 40526 40625 40585 NoData NoData
aarch64-n1sdp:
$sudo ./app/test/dpdk-test --lcore '(0-1)@1'
Testing using two hyperthreads(bulk (size: 8):)
iter_shift: 3 5 7 9 11 13 *15 17 19 21 23
run time: 8s 8s 8s 9s 9s 14s 34s 111s 418s 25min >1h
legacy APIs: SP/SC: 0.4 0.2 0.1 488 488 488 488 488 489 489 NoData
legacy APIs: MP/MC: 0.4 0.3 0.2 488 488 488 488 490 489 489 NoData
As the number of iterations increases, so does the time which is required
to run the program. Currently (iter_shift = 23), it will take more than
1 hour to wait for the test to finish. To fix this, the "iter_shift" should
decrease and ensure enough iterations to keep the test data stable.
In order to achieve this, we also test with "-l" EAL argument:
x86-Intel(R) Xeon(R) Gold 6240:
$sudo ./app/test/dpdk-test -l 25-26
Testing using two NUMA nodes(bulk (size: 8):)
iter_shift: 3 5 7 9 11 13 *15 17 19 21 23
run time: 6s 6s 6s 6s 6s 6s 6s 7s 8s 11s 27s
legacy APIs: SP/SC: 47 20 13 22 54 83 91 73 81 75 95
legacy APIs: MP/MC: 44 18 18 240 245 270 250 249 252 250 253
aarch64-n1sdp:
$sudo ./app/test/dpdk-test -l 1-2
Testing using two physical cores(bulk (size: 8):)
iter_shift: 3 5 7 9 11 13 *15 17 19 21 23
run time: 8s 8s 8s 8s 8s 8s 8s 9s 9s 11s 23s
legacy APIs: SP/SC: 0.7 0.4 1.2 1.8 2.0 2.0 2.0 2.0 2.0 2.0 2.0
legacy APIs: MP/MC: 0.3 0.4 1.3 1.9 2.9 2.9 2.9 2.9 2.9 2.9 2.9
According to above test data, when "iter_shift" is set as "15", the test
run time is reduced to less than 1 minute and the test result can keep
stable in x86 and aarch64 servers.
Fixes: 1fa5d0099e ("test/ring: add custom element size performance tests")
Cc: stable@dpdk.org
Signed-off-by: Feifei Wang <feifei.wang2@arm.com>
Reviewed-by: Honnappa Nagarahalli <honnappa.nagarahalli@arm.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The distributor library implementation uses a cyclic queue to store
packets returned from workers. These packets can be later collected
with rte_distributor_returned_pkts() call.
However the queue has limited capacity. It is able to contain only
127 packets (RTE_DISTRIB_RETURNS_MASK).
Big burst tests sent 1024 packets in 32 packets bursts without waiting
until they are processed by the distributor. In case when tests were
run with big number of worker threads, it happened that more than
127 packets were returned from workers and put into cyclic queue.
This caused packets to be dropped by the queue, making them impossible
to be collected later with rte_distributor_returned_pkts() calls.
However the test waited for all packets to be returned infinitely.
This patch fixes the big burst test by not allowing more than
queue capacity packets to be processed at the same time, making
impossible to drop any packets.
It also cleans up duplicated code in the same test.
Bugzilla ID: 612
Fixes: c0de0eb82e ("distributor: switch over to new API")
Cc: stable@dpdk.org
Signed-off-by: Lukasz Wojciechowski <l.wojciechow@partner.samsung.com>
Tested-by: David Marchand <david.marchand@redhat.com>
Reviewed-by: David Hunt <david.hunt@intel.com>
Currently, test-flow-perf app cannot generate flows with meter action.
This patch introduces new parameter "--meter" to generate flows
with meter action.
Signed-off-by: Dong Zhou <dongzhou@nvidia.com>
Reviewed-by: Wisam Jaddo <wisamm@nvidia.com>
Reviewed-by: Alexander Kozyrev <akozyrev@nvidia.com>
The app will calculate and output used CPU time for flow insertion rate.
It's also needed for some new insertion items, such as meter.
It's better to split this calculation and output part to a single function,
so that all new insertion items can use it.
Signed-off-by: Dong Zhou <dongzhou@nvidia.com>
Reviewed-by: Wisam Jaddo <wisamm@nvidia.com>
Reviewed-by: Alexander Kozyrev <akozyrev@nvidia.com>
We need to differentiate between crypto and ethernet security
context as they belong to different devices.
Fixes: d82d6ac643 ("app/procinfo: add crypto security context info")
Cc: stable@dpdk.org
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Meson can use cmake as a fallback for detecting packages, and this can
lead to picking up 64-libs for 32-bit builds. To work around this, force
the use of pkg-config only for detecting libcrypto, zlib, jansson and
other package dependencies.
Cc: stable@dpdk.org
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Tested-by: Ruifeng Wang <ruifeng.wang@arm.com>
Tested-by: Liron Himi <lironh@marvell.com>
Tested-by: Lee Daly <lee.daly@intel.com>
Tested-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Tested-by: Martin Spinler <spinler@cesnet.cz>
The "includes" variable in the app/meson.build file was ignored when
building the executable, meaning that apps couldn't pass additional
include paths directly back. Fix this to align with drivers and libs.
Fixes: fa036e70d7 ("app: generalize meson build")
Cc: stable@dpdk.org
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Reviewed-by: David Marchand <david.marchand@redhat.com>
Support rss action in the sample sub-actions list.
The examples for the sample flow use case and result as below:
set sample_actions 0 mark id 0x12 / rss queues 0 1 2 3 end / end
flow create 0 ingress group 1 pattern eth / end actions
sample ratio 1 index 0 / jump group 2 / end
This flow will result in all the matched ingress packets will be
jumped to next table, and the each packet will be marked with 0x12
and duplicated to rss queues of the control application.
Signed-off-by: Jiawei Wang <jiaweiw@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Add support for the RTE_FLOW_ACTION_MODIFY_FIELD to the testpmd.
Implement CLI to create the modify_field action and supply all the
needed parameters to modify an arbitrary packet field (as well as
mark, tag or metadata) with data from another field or immediate
value.
Example of the flow is the following:
flow create 0 egress group 1 pattern eth / ipv4 / udp / end
actions modify_field op set dst_type tag dst_level 2 dst_offset 8
src_type gtp_teid src_level 0 src_offset 0 width 16 / end
This flow copies 16 bits from the second Tag in the Tags array
into the outermost GTP TEID packet header field. 8 bits of the
Tag are skipped as indicated by the dst_offset action parameter.
op, dst_type, src_type and width are the mandatory parameters to
specify. Levels and offset are 0 by default if they are not
overridden by a user. The operation can be set, add or sub.
Signed-off-by: Alexander Kozyrev <akozyrev@nvidia.com>
Acked-by: Ori Kam <orika@nvidia.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Strict-aliasing rules are violated by cast to uint16_t* in flowgen.c and
the calculated IP checksum is wrong. Use attribute __may_alias__ to fix
the problem.
Fixes: e9e23a617e ("app/testpmd: add flowgen forwarding engine")
Cc: stable@dpdk.org
Signed-off-by: George Prekas <prekageo@amazon.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
The patch adds the GENEVE rte flow option length support to
command line interpreter. The flow command with GENEVE
option items looks like:
flow create 0 ingress pattern eth / ipv4 / udp / geneve vni
is 100 optlen is 2 / end actions drop / end
The option length should be specified in 32-bit words, this
value specifies the all options length in the GENEVE header.
Signed-off-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Acked-by: Ori Kam <orika@nvidia.com>
The patch adds the GENEVE option rte flow item support to
command line interpreter. The flow command with GENEVE
option items looks like:
flow create 0 ingress pattern eth / ipv4 / udp / geneve vni is 100 /
geneve-opt class is 99 length is 1 type is 0 data is 0x669988 /
end actions drop / end
The option length should be specified in 32-bit words, this
value specifies the length of the data pattern/mask arrays (should be
multiplied by sizeof(uint32_t) to be expressed in bytes. If match
on the length itself is not needed the mask should be set to zero, in
this case length is used to specify the pattern/mask array lengths only.
Signed-off-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Acked-by: Ori Kam <orika@nvidia.com>
When the max rx packet length is smaller than the sum of mtu size and
ether overhead size, it should be enlarged, otherwise the VLAN packets
will be dropped.
Removed the rx_offloads assignment for jumbo frame during command line
parsing, and set the correct jumbo frame flag if MTU size is larger than
the default value 'RTE_ETHER_MTU' within 'init_config()'.
Fixes: 384161e006 ("app/testpmd: adjust on the fly VLAN configuration")
Fixes: 35b2d13fd6 ("net: add rte prefix to ether defines")
Fixes: ce17eddefc ("ethdev: introduce Rx queue offloads API")
Fixes: 150c9ac2df ("app/testpmd: update Rx offload after setting MTU")
Cc: stable@dpdk.org
Signed-off-by: Steve Yang <stevex.yang@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Request the driver for number of entries in the FEC caps
array and then dynamically allocate the array.
Signed-off-by: Karra Satwik <kaara.satwik@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
Acked-by: Min Hu (Connor) <humin29@huawei.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
