The index of an event queue index is computed from the index of the
corresponding transmit or receive queue, and depends on the total
number of receive queues. As a consequence, the index of an event
queue bound to a transmit queue changes if the total number of
receive queues is changed.
Fixes: 58294ee65a ("net/sfc: support event queue")
Cc: stable@dpdk.org
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
Make it clear that corresponding functions should be called on device
configure and close operations. No functional change.
Fixes: 06bc197796 ("net/sfc: interrupts support sufficient for event queue init")
Cc: stable@dpdk.org
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
If Tx datapath does not support TSO, TSO was dropped on device configure.
It is incorrect to change advertised offloads.
Fixes: 7a4d44a639 ("net/sfc: make TSO a datapath-dependent feature")
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Datapath choice requires NIC capabilities knowledge and, therefore,
should be done after probe. Whereas NIC resources estimation needs
to know chosen datapath (e.g. if Tx datapath is going to use TSO).
Fixes: df1bfde4ff ("net/sfc: factor out libefx-based Rx datapath")
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Put to mempool does not free chained segments.
Fixes: e0b063941e ("net/sfc: support scattered Rx DMA")
Cc: stable@dpdk.org
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Split control and datapath to make datapath substitutable and
possibly reusable with alternative control path.
libefx-based Tx datapath is bound to libefx control path, but
it should be possible to use other datapaths with alternative
control path(s).
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
If Rx refill threshold guarantees that refill happens for one or
more bulks, less checks may be done on refill.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Split control and datapath to make datapath substitutable and
possibly reusable with alternative control path.
libefx-based Rx datapath is bound to libefx control path, but
other datapaths should be possible to use with alternative
control path(s).
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Rx queue flags should keep the information required on datapath.
It is a preparation to split control and data paths.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Use different sets of libefx EvQ callbacks for management,
transmit and receive event queue. It makes event handling
more robust against unexpected events.
Also it is required for alternative datapath support.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Some libefx-based drivers might need this functionality to
indicate DPCPU FW IDs as part of FW version info to assist
experienced users.
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
The patch is to add support for MCDI proxy which comes in
useful, particularly, while running over VF: few commands
will normally fail with EPERM, but in some cases the host
driver (i.e. running over the corresponding PF, typically,
within a hypervisor) may set itself as a proxy to conduct
authorization for the commands coming from VFs; these are
forwarded to the corresponding access control application
which may decline or approve authorization by replying to
the requests; all in all, the guest driver has to process
the replies forwarded back by the firmware MC in order to
give up gracefully (by setting return code which could be
understood by 'libefx') or re-issue the original commands
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
If Rx mode is unacceptable, in particular, when promiscuous
or all-multicast filters are not allowed while running over
PCI function which is not a member of appropriate privilege
groups, the driver has to cope with the failures gracefully
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
If periodic DMA statistics feature is absent (particularly,
while running over VF), the PMD must provide an ability to
cope with it using explicit update requests which are kept
restrained according to 'stats_update_period_ms' parameter
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
The patch is to make MAC statistics update interval tunable
by means of 'stats_update_period_ms' kvarg parameter making
it possible to use values different from 1000 ms in case of
SFN8xxx boards provided that firmware version is 6.2.1.1033
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
According to 'libefx' API requirements, one is allowed to
apply multicast address list to the port in started state
only, otherwise the new array should be copied to a local
storage in order to be applied during the next port start
Coverity issue: 141296
Fixes: 0fa0070e43 ("net/sfc: support multicast addresses list controls")
Fixes: e9ddf37a50 ("net/sfc: fix setting empty multicast list")
Cc: stable@dpdk.org
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
Support individual/group destination address match (unknown unicast
and all-multicast correspondingly in terms of firmware).
Signed-off-by: Roman Zhukov <roman.zhukov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Exact match of source and destination ports is supported by parser.
IP protocol match is enforced to UDP.
Signed-off-by: Roman Zhukov <roman.zhukov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Exact match of source and destination ports is supported by parser.
IP protocol match is enforced to TCP.
Signed-off-by: Roman Zhukov <roman.zhukov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Exact match of IP protocol, source and destination
addresses is supported by parser.
EtherType match is enforced to IPv6 EtherType.
Signed-off-by: Roman Zhukov <roman.zhukov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Exact match of IP protocol, source and destination
addresses is supported by parser.
EtherType match is enforced to IPv4 EtherType.
Signed-off-by: Roman Zhukov <roman.zhukov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Exact match of VLAN ID bits is supported only and required in VLAN item.
Mask to match VLAN ID bits only is required, default mask to match entire
TCI is not supported.
Signed-off-by: Roman Zhukov <roman.zhukov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Only pattern items VOID, ETH and actions VOID, QUEUE is now
supported.
Signed-off-by: Roman Zhukov <roman.zhukov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
The information is obtained from firmware on attach. It may
change after MC reboot (firmware version or variant change).
Cache should be refreshed after MC reboot when it is handled
properly (not yet).
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
Just log error for all filter types and return no support indication.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
The previous API had various problems, including the length of the
caller provided buffer not being specified, no means being available
to discover how big the buffer needs to be, and a lack of clarity of
what the resulting list contains.
To improve it:
- add the buffer length as a parameter
- if the provided buffer is too short, fail with ENOSPC and return
the required length
- ensure that the list contents are valid and add comments describing it
It is safe to change this API as, unsurprisingly, it has no users.
Signed-off-by: Mark Spender <mspender@solarflare.com>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
The flag EFX_FILTER_MATCH_LOC_MAC_IG to represent filtering on the
individual/group bit of the MAC address (with the two cases being
distinguished by the MAC address in the filter specification) was
introduced to mirror the Linux driver filtering code, but the
implementations are different enough anyway that it isn't of much
value.
Having separate flags for unknown unicast and multicast simplifies
the code and allows the set of flags to match those used by MCDI.
It will also makes it easier to report whether these filters are
supported.
In the MCDI definitions, the unknown multicast and unicast flags
have the values 0x40000000 and 0x80000000 respectively, and so using
the same values for simplicity requires 32 bits in the filter
specification to store the flags. This means the structure is now
a little bigger than 64 bytes, but filters are not often used on
critical paths so this shouldn't have much impact - on Linux they
are also bigger than they used to be.
Signed-off-by: Mark Spender <mspender@solarflare.com>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
EF10 supported by the PMD has no limitations on address boundary
crossing by Tx DMA descriptors.
Fixes: 428c7ddd2f ("net/sfc: send bursts of packets")
Fixes: fec33d5bb3 ("net/sfc: support firmware-assisted TSO")
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Siena has limitation on maximum byte count and 4k boundary crosssing
(which is stricter than maximum byte count).
EF10 has limitation on maximum byte count only.
Fixes: f7dc06bf35 ("net/sfc/base: import 5xxx/6xxx family support")
Fixes: e7cd430c86 ("net/sfc/base: import SFN7xxx family support")
Fixes: 94190e3543 ("net/sfc/base: import SFN8xxx family support")
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
If a libefx-based driver needs some way to clear port statistics,
then an MCDI agnostic method is required.
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Before this patch, the management of dependencies between directories
had several issues:
- the generation of .depdirs, done at configuration is slow: it can take
more than one minute on some slow targets (usually ~10s on a standard
PC without -j).
- for instance, it is possible to express a dependency like:
- app/foo depends on lib/librte_foo
- and lib/librte_foo depends on app/bar
But this won't work because the directories are traversed with a
depth-first algorithm, so we have to choose between doing 'app' before
or after 'lib'.
- the script depdirs-rule.sh is too complex.
- we cannot use "make -d" for debug, because the output of make is used for
the generation of .depdirs.
This patch moves the DEPDIRS-* variables in the upper Makefile, making
the dependencies much easier to calculate. A DEPDIRS variable is still
used to process library dependencies in LDLIBS.
After this commit, "make config" is almost immediate.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Tested-by: Robin Jarry <robin.jarry@6wind.com>
Tested-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
The patch is to fix sfc_set_mc_addr_list() behaviour in order
to make it accept an empty multicast address list thus making
it possible to remove multicast addresses inserted previously
Fixes: 0fa0070e43 ("net/sfc: support multicast addresses list controls")
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
