This patch includes 3 changes related to MAC/VLAN address table
when the system (e.g. testpmd) is started and closed:
- remove default MAC address with fixed VLAN 0 which was for the
debug purpose before the MAC/VLAN filter function was implemented.
- enable VF MAC/VLAN filter for the first valid MAC address
and first valid VLAN ID. This is needed for system (e.g. testpmd)
to setup default MAC address and default VLAN for VF.
Later attempt to change these default value will be refused by
under layer shared code and PF host functions.
- un-register any combination of VLAN and MAC address from fm10k
switch side MAC table when the system (e.g. testpmd) is closed.
Signed-off-by: Shaopeng He <shaopeng.he@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
Tested-by: Michael Qiu <michael.qiu@intel.com>
Fm10k PF/VF does not support QinQ; VLAN strip and filter are always on
for PF/VF ports.
Signed-off-by: Shaopeng He <shaopeng.he@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
MAC filter function was newly added, each PF and VF can have up to
64 MAC addresses.
VF filter needs support from PF host, which is not available now.
Signed-off-by: Shaopeng He <shaopeng.he@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
VLAN filter was updated to add/delete one static entry in MAC table for
each combination of VLAN and MAC address. More sanity checks were added.
Signed-off-by: Shaopeng He <shaopeng.he@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
Since the communication between PF/Switch Manager, VF/PF is
asynchronous through mailbox, it's hard to determine when Switch
Manager/PF host will send the default vlan to PF/VF. So, it's
necessary to set default vlan until the device is started.
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Acked-by: Michael Qiu <michael.qiu@intel.com>
After acquiring MAC address from HW, it's necessary to validate
MAC address before use.
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Tested-by: Michael Qiu <michael.qiu@intel.com>
Acked-by: Michael Qiu <michael.qiu@intel.com>
In fm10k, PF driver needs to communicate with switch through
mailbox if it needs to add/delete MAC address.
This fix will validate if switch is ready before going forward.
Then, it is necessary to acquire LPORT_MAP info after issuing
MAC addr request to switch.
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Tested-by: Michael Qiu <michael.qiu@intel.com>
Acked-by: Michael Qiu <michael.qiu@intel.com>
fm10k can't receive frame greater than 1536 and Scatter RX
function can't work correctly. The root cause is
SRRCTL.FM10K_SRRCTL_BUFFER_CHAINING_EN bit is not enabled.
Test report: http://dpdk.org/ml/archives/dev/2015-June/019242.html
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Tested-by: Michael Qiu <michael.qiu@intel.com>
Acked-by: Michael Qiu <michael.qiu@intel.com>
As RX buffer is aligned to 512B within mbuf, some bytes are reserved
for this purpose, and the worst case could be 511B. But SRR reg
assumes all buffers have the same size. In order to fill the gap,
we'll have to consider the worst case and assume 512B is reserved.
If we don't do so, it's possible for HW to overwrite data to next
mbuf.
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Tested-by: Michael Qiu <michael.qiu@intel.com>
Acked-by: Michael Qiu <michael.qiu@intel.com>
Both PF and VF shared code in function fm10k_stats_get().
The function works well with PF, but has problem with VF since
VF has less queues than PF.
Fixes: a6061d9e7075 ("fm10k: register PF driver")
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Acked-by: Michael Qiu <michael.qiu@intel.com>
Original implementation required mbuf size should be greater than
ETHER_MAX_VLAN_FRAME_LEN, which is not necessary. If it's less
than that value, scatter function will be selected and incoming
packets greater than mbuf size will be filled into several mbufs.
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Acked-by: Michael Qiu <michael.qiu@intel.com>
Add functions to support promiscuous/allmulticast enable and
disable.
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Tested-by: Michael Qiu <michael.qiu@intel.com>
Acked-by: Michael Qiu <michael.qiu@intel.com>
Upcoming drivers will need to be able to support other bus types.
This is a transparent change to how struct eth_driver is initialized.
It has not function or ABI layout impact, but makes adding a later
bus type (Xen, Hyper-V, ...) much easier.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
In DPDK, max_vfs means vf numbers created, not the max number vfs
the device supported.
Signed-off-by: Michael Qiu <michael.qiu@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
move fm10k PMD to drivers/net directory
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
