Add extended PHY types to get PHY abilities for 25G, then put
PHY types for 25G into the proper field when the PHY capabilities
are queried.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Previously, PTYPE filed in the RX descriptors is not set properly
for QinQ packets. The wrong PTYPE is generated because outer Tag did
not have ORT/PIT configured, so fix this issue by configuring ORT/PIT.
This patch also changes bitmask of outer VLAN tag in L2 header
to support RSS and flow director for QinQ.
Fixes: 4861cde461 ("i40e: new poll mode driver")
Fixes: 4072d503aa ("i40e: fix VLAN bitmasks for input set")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
When using VMDQ+RSS, the queue ids used by the application are not
contiguous (see i40e_pf_config_rss). Most of the driver already handled
this, but there were a few cases where it assumed all configured queues
had been setup.
Fixes: 4861cde461 ("i40e: new poll mode driver")
Fixes: 6b45371283 ("i40e: free queue memory when closing")
Fixes: 8e109464c0 ("i40e: allow vector Rx and Tx usage")
Signed-off-by: Rich Lane <rich.lane@bigswitch.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
In FW default settings, Ethertype 0x88A8 is treated as S-TAG,
and packets with S-TAG should be received in Port Virtualizer mode.
However, Port Virtualizer mode is not initialized in DPDK, so X710 will
drop packets with Ethertype 0x88A8.
This patch fixes this issue by turning off S-TAG identification.
Fixes: 4861cde461 ("i40e: new poll mode driver")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
To make the PCTYPE in x722 compatible with original PCTYPE in
flow director (FD) filters, the PCTYPE in the FD programming
descriptor needs to be translated into a different PCTYPE using
GLQF_FD_PCTYPE table.
Translation needs to be done before the FD filter is programmed.
Signed-off-by: Jeff Guo <jia.guo@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
For the vector PMD, release all mbufs from the Rx queue if no packets
are received after device start.
Fixes: 9ed94e5bb0 ("i40e: add vector Rx")
Signed-off-by: Yury Kylulin <yury.kylulin@intel.com>
Acked-by: Beilei Xing <beilei.xing@intel.com>
Interestingly, clang and gcc has different prototype for _mm_prefetch().
For gcc, we have
_mm_prefetch (const void *__P, enum _mm_hint __I)
While for clang, it's
#define _mm_prefetch(a, sel) (__builtin_prefetch((void *)(a), 0, (sel)))
That's how the following error comes with clang:
error: cast from 'const void *' to 'void *' drops const qualifier
[-Werror,-Wcast-qual]
_mm_prefetch((const void *)rused, _MM_HINT_T0);
/usr/lib/llvm-3.8/bin/../lib/clang/3.8.0/include/xmmintrin.h:684:58:
note: expanded from macro '_mm_prefetch'
#define _mm_prefetch(a, sel) (__builtin_prefetch((void *)(a),
0, (sel)))
What's weird is that the build was actaully Okay before. I met it while
apply Jerin's vector support for ARM patch set: he just move this piece
of code to another file, nothing else changed.
This patch fix the issue when Jerin's patchset is applied. Thus, I think
it's still needed.
Similarly, make the same change to other _mm_prefetch users, just in case
this weird issue shows up again somehow later.
Fixes: fc3d66212f ("virtio: add vector Rx")
Fixes: c95584dc2b ("ixgbe: new vectorized functions for Rx/Tx")
Fixes: 9ed94e5bb0 ("i40e: add vector Rx")
Fixes: 7092be8437 ("fm10k: add vector Rx")
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
Now that rte_device is available, drivers can start using its members
(numa, name) as well as link themselves into another rte_device list.
As of now no one is using this list, but can be used for moving over all
devices (pdev/vdev/Xdev) and perform bulk actions (like cleanup).
Signed-off-by: Jan Viktorin <viktorin@rehivetech.com>
[Shreyansh: Reword commit log for extra rte_device list]
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: David Marchand <david.marchand@6wind.com>
Remove the 'name' member from rte_pci_driver and move to generic
rte_driver.
Most of the PMD drivers were initially using DRIVER_REGISTER_PCI(<name>..)
as well as assigning a name to eth_driver.pci_drv.name member.
In this patch, only the original DRIVER_REGISTER_PCI(<name>..) name has
been populated into the rte_driver.name member - assignments through
eth_driver has been removed.
Signed-off-by: Jan Viktorin <viktorin@rehivetech.com>
[Shreyansh: Rebase and expand changes to newly added files]
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: David Marchand <david.marchand@6wind.com>
Simplify crypto and ethdev pci drivers init by using newly introduced
init macros and helpers.
Those drivers then don't need to register as "rte_driver"s anymore.
Exceptions:
- virtio and mlx* use RTE_INIT directly as they have custom initialization
steps.
- VDEV devices are not modified - they continue to use PMD_REGISTER_DRIVER.
Update documentation for replacing an example referring to
PMD_REGISTER_DRIVER.
Signed-off-by: David Marchand <david.marchand@6wind.com>
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
As discussed in the past release, driver names are modified
to be more consistent, and the future driver should follow
this new convention.
Driver names consist of:
"driver category"_"driver folder name"_"optional extra name".
For example:
- Crypto null driver -> "crypto_null"
- Network IXGBE VF driver -> "net_ixgbe_vf"
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
The driver is incorrectly setting the RSS field in the last mbuf in
the packet chain instead of the first. Moreover, the last mbuf might
have already been freed if it only contained the Ethernet CRC.
Also, fix the call to i40e_rxd_build_fdir to store the fdir flags in
the first mbuf of the chain instead of the last.
Fixes: 4861cde461 ("i40e: new poll mode driver")
Fixes: 5a21d9715f ("i40e: report flow director matching")
Signed-off-by: Dumitru Ceara <dumitru.ceara@gmail.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
VSI structure needs to be removed from TAILQ list when releasing.
But for the child VSI it will be removed again after the structure
is freed. It will cause core dump when the DPDK i40e using as PF
host driver.
This patch fixes it to only remove child VSI from TAILQ before
send adminq command to remove it from hardware.
Fixes: 4861cde461 ("i40e: new poll mode driver")
Fixes: 440499cf53 ("net/i40e: support floating VEB")
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
i40e driver was removing elements when iterating tailq lists
with TAILQ_FOREACH macro, which is not safe.
It is especially visible since the memory is zeroed on free
(commit ea0bddbd14).
Instead, TAILQ_FOREACH_SAFE macro is used when removing/freeing
these elements.
Fixes: 4861cde461 ("i40e: new poll mode driver")
Fixes: 440499cf53 ("net/i40e: support floating VEB")
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Rx loop inside _recv_raw_pkts_vec() ignores nb_pkts argument and always
tries to receive RTE_I40E_VPMD_RX_BURST (32) packets. This is a violation
of rte_eth_rx_burst() API and can lead to memory corruption (out-of-bounds
writes to struct rte_mbuf **rx_pkts) if nb_pkts is less than 32.
Fix this by actually using nb_pkts inside the loop.
Fixes: 9ed94e5bb0 ("i40e: add vector Rx")
Signed-off-by: Sergey Dyasly <s.dyasly@samsung.com>
Acked-by: Ilya Maximets <i.maximets@samsung.com>
Acked-by: Adam Bynes <adambynes@outlook.com>
This reverts commit 4761f57d58.
Introducing VLAN table by adding VLAN adminq command will cause NIC's
throughput drop obviously. It's a hardware issue.
With this revert, VLAN filtering can only work when promiscuous mode
is disabled.
Reverts: 4761f57d58 ("net/i40e: fix VLAN filtering in promiscuous mode")
Reported-by: Jeff Shaw <jeffrey.b.shaw@intel.com>
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by : Jing Chen <jing.d.chen@intel.com>
When calling i40e_flowtype_to_pctype in i40e_get_hash_filter_global_config
and i40e_set_hash_filter_global_config, function i40e_flowtype_to_pctype
will be possibly make an out-of-bounds access, because size of the array
is 15. So check the flow type is valid before calling
i40e_flowtype_to_pctype.
In the process fix other occurances of the same problem
Coverity issue: 37793, 37794
Fixes: 782c8c92f1 ("i40e: add hash configuration")
Fixes: f2b2e2354b ("i40e: split function for hash and flow director input")
Fixes: 98f0557076 ("i40e: configure input fields for RSS or flow director")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Null-checking vsi suggests that it may be null, but it
has been dereferenced before null-checking. So move the
check to before the assignment statement using the pointer.
Coverity issue: 119265, 119266
Fixes: d0a349409b ("i40e: support AQ based RSS config")
Fixes: 647d1eaf75 ("i40evf: support AQ based RSS config")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
The condition, "(pf->flags | I40E_FLAG_VMDQ)" will always be true,
regardless of the value of the flags operand, because I40E_FLAG_VMDQ
is 4ULL - meaning at least one bit will always be set in the result.
That will cause log error when VMDq is disabled.
Since the original intent behind the condition is to check if VMDq
is enabled, fix the code by changing "|" to "&".
Coverity issue: 13219, 13221
Fixes: 4805ed59e9 ("i40e: enhance mac address operations")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
For VLAN filtering, the VLAN table should be enabled.
But the VLAN table is disabled by default until a rule is added.
In promiscuous mode no rule is added to enable the VLAN table.
This patch clears promiscuous VLAN flag on VSI, and adds a
rule to enable the VLAN table to fix VLAN filtering in promiscuous
mode.
Fixes: 4861cde461 ("i40e: new poll mode driver")
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The ethtool app was allocating too little space for 64-bit
registers which resulted in memory corruption.
Removes hard-coded assumption that device registers
are always 32 bits wide. The rte_eth_dev_get_reg_length
and rte_eth_dev_get_reg_info callbacks did not
provide register size to the app in any way while is
needed to allocate correct number of bytes before
retrieving registers using rte_eth_dev_get_reg.
This commit changes rte_eth_dev_get_reg_info so that
it can be used to retrieve both the number of registers
and their width, and removes the now-redundant
rte_eth_dev_get_reg_length.
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Modify the PMD_REGISTER_DRIVER macro, adding a name argument to it. The
addition of a name argument creates a token that can be used for subsequent
macros in the creation of unique symbol names to export additional bits of
information for use by the pmdinfogen tool. For example:
PMD_REGISTER_DRIVER(ena_driver, ena);
registers the ena_driver struct as it always did, and creates a symbol
const char this_pmd_name0[] __attribute__((used)) = "ena";
which pmdinfogen can search for and extract. The subsequent macro
DRIVER_REGISTER_PCI_TABLE(ena, ena_pci_id_map);
creates a symbol const char ena_pci_tbl_export[] __attribute__((used)) =
"ena_pci_id_map";
Which allows pmdinfogen to find the pci table of this driver
Using this pattern, we can export arbitrary bits of information.
pmdinfo uses this information to extract hardware support from an object
file and create a json string to make hardware support info discoverable
later.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Panu Matilainen <pmatilai@redhat.com>
Acked-by: Remy Horton <remy.horton@intel.com>
For all drivers that currently implement xstats, the id field in the
rte_eth_stats_name structure equals the entry's array index. This
patch eliminates the redundant id field as a direct index lookup is
faster than a search for the matching id field.
Suggested-by: Olivier Matz <olivier.matz@6wind.com>
Signed-off-by: Remy Horton <remy.horton@intel.com>
The standard Virtual Ethernet Bridge(VEB) definition in 1Qbg is a bridge
which has an uplink port to the outside world (maybe another bridge), but
a "floating" VEB is a special VEB without an uplink port to the outside.
Instead, traffic can be sent from one VF to another using the floating
VEB - even when the physical link on the NIC port is down.
This patch adds floating VEB options in the devargs for i40e driver.
Using these parameters, applications can decide whether to use legacy
VEB/VEPA or a floating VEB.
To enable this feature, the user should pass a devargs parameter to the
EAL, for example "-w 84:00.0,enable_floating_veb=1", to control whether
the PMD will to use the floating VEB feature or not.
Once the floating VEB feature is enabled, all the VFs created by
this PF device are connected to the floating VEB.
NOTE: The floating VEB functionality requires a NIC firmware version
of 5.0 or greater.
Signed-off-by: Zhe Tao <zhe.tao@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
The standard Virtual Ethernet Bridge(VEB) definition in 1Qbg is a bridge
which has an uplink port to the outside world (maybe another bridge),
but a "floating" VEB is a special VEB without an uplink port to the
outside. Instead, traffic can be sent from one VF to another using the
floating VEB - even when the physical link on the NIC port is down.
VFs VSIs connect either to the standard VEB/VEPA or to the floating VEB,
they cannot connect to both of them. The PF, VMDQ and FD VSIs still
connect to the normal VEB/VEPA.
Signed-off-by: Zhe Tao <zhe.tao@intel.com>
Delete 'case I40E_VIRTCHNL_OP_FCOE', as it is not necessary. The
default case reports on all unsupported commands included this one.
This also prevents warnings about a missing "break" at the end of the
"case" block.
Coverity issue: 13265
Fixes: 4861cde461 ("i40e: new poll mode driver")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
This patch fixes the issues reported by Coverity of 'Dereference
before null check', by deleting unnecessary null checks, or moving
null checks to before the offending use of the pointer.
Coverity issue: 13298, 13299, 13294, 13301, 119267
Fixes: 8e109464c0 ("i40e: allow vector Rx and Tx usage")
Fixes: a778a1fa2e ("i40e: set up and initialize flow director")
Fixes: a778a1fa2e ("i40e: set up and initialize flow director")
Fixes: 4861cde461 ("i40e: new poll mode driver")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
In current i40e codebase, if single VLAN header is added in a packet,
it's treated as inner VLAN. Generally, a single VLAN header is
treated as the outer VLAN header, so update the driver behaviour
appropriately.
Fixes: 19b16e2f64 ("ethdev: add vlan type when setting ether type")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
The flags for RSS and flow director are not set correctly in the vector
Rx function, so applications which use these flags will not work
correctly.
The problem is caused by incorrect constants for masking,
shuffling and shifting the descriptor bytes, to create the resultant
flags in the mbuf. Correcting the constants fixes the problem
Fixes: 9ed94e5bb0 ("i40e: add vector Rx")
Signed-off-by: Zhe Tao <zhe.tao@intel.com>
Reviewed-by: Piotr Azarewicz <piotrx.t.azarewicz@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Update the documentation and comments with brief details on the base
code version included in this release.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Add a flag which can be used to tell the firmware to disable the link on
all ports.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Add opcodes and structures to support RSS configuration
by PF driver on behalf of the VF drivers.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Adds input set mask definitions for RSS, flow director
and flex bytes.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Adds more device capabilities for NVM management.
- if update is available
- if security check is needed
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Correct the number of MSIX vector in debug info.
Fixes: 889bc9f0cd ("i40e/base: unify the capability function")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Remove a problematic mirror rule ID check. The check
returned an error if the mirror rule ID is 0, which is
a valid value.
Fixes: 0bf2dbbe07 ("i40e/base: support mirroring rules")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Allow egress traffic to be mirrored to VSIs in promiscuous mode, as latest
firmware supports that from API version 1.5.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
The hardware doesn't layout the Geneve VNI (Virtual Network
Identifier) quite the same as the VxLAN VNI, so it needs to
adjust it before sending through the Admin Queue commands as the
workaround.
Fixes: 8db9e2a1b2 ("i40e: base driver")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch trims the source code, with limiting pieces of code for
PF or VF driver only, code style fixes, and annotation
rewording.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
