When calling to setup RSS on v4 API, ESX will expect
IPv4/6 TCP RSS to be set/requested mandatory.
This patch will:
- Set IPv4/6 TCP RSS when these have not been set. A warning
message is thrown to make sure we warn the application we are
setting IPv4/6 TCP RSS when not set.
- An additional check has been added to dodge RSS configuration
altogether unless MQ_RSS has been requested, similar to v3.
The alternative (returning error) was considered, the intent
is to ease the task of setting up and running vmxnet3 in situations
where it's supposed to be most straightforward (testpmd, pktgen).
Bugzilla ID: 400
Fixes: 643fba7707 ("net/vmxnet3: add v4 boot and guest UDP RSS config")
Cc: stable@dpdk.org
Signed-off-by: Eduard Serra <eserra@vmware.com>
Acked-by: Yong Wang <yongwang@vmware.com>
Add 'RTE_' prefix to defines:
- rename ETHER_ADDR_LEN as RTE_ETHER_ADDR_LEN.
- rename ETHER_TYPE_LEN as RTE_ETHER_TYPE_LEN.
- rename ETHER_CRC_LEN as RTE_ETHER_CRC_LEN.
- rename ETHER_HDR_LEN as RTE_ETHER_HDR_LEN.
- rename ETHER_MIN_LEN as RTE_ETHER_MIN_LEN.
- rename ETHER_MAX_LEN as RTE_ETHER_MAX_LEN.
- rename ETHER_MTU as RTE_ETHER_MTU.
- rename ETHER_MAX_VLAN_FRAME_LEN as RTE_ETHER_MAX_VLAN_FRAME_LEN.
- rename ETHER_MAX_VLAN_ID as RTE_ETHER_MAX_VLAN_ID.
- rename ETHER_MAX_JUMBO_FRAME_LEN as RTE_ETHER_MAX_JUMBO_FRAME_LEN.
- rename ETHER_MIN_MTU as RTE_ETHER_MIN_MTU.
- rename ETHER_LOCAL_ADMIN_ADDR as RTE_ETHER_LOCAL_ADMIN_ADDR.
- rename ETHER_GROUP_ADDR as RTE_ETHER_GROUP_ADDR.
- rename ETHER_TYPE_IPv4 as RTE_ETHER_TYPE_IPv4.
- rename ETHER_TYPE_IPv6 as RTE_ETHER_TYPE_IPv6.
- rename ETHER_TYPE_ARP as RTE_ETHER_TYPE_ARP.
- rename ETHER_TYPE_VLAN as RTE_ETHER_TYPE_VLAN.
- rename ETHER_TYPE_RARP as RTE_ETHER_TYPE_RARP.
- rename ETHER_TYPE_QINQ as RTE_ETHER_TYPE_QINQ.
- rename ETHER_TYPE_ETAG as RTE_ETHER_TYPE_ETAG.
- rename ETHER_TYPE_1588 as RTE_ETHER_TYPE_1588.
- rename ETHER_TYPE_SLOW as RTE_ETHER_TYPE_SLOW.
- rename ETHER_TYPE_TEB as RTE_ETHER_TYPE_TEB.
- rename ETHER_TYPE_LLDP as RTE_ETHER_TYPE_LLDP.
- rename ETHER_TYPE_MPLS as RTE_ETHER_TYPE_MPLS.
- rename ETHER_TYPE_MPLSM as RTE_ETHER_TYPE_MPLSM.
- rename ETHER_VXLAN_HLEN as RTE_ETHER_VXLAN_HLEN.
- rename ETHER_ADDR_FMT_SIZE as RTE_ETHER_ADDR_FMT_SIZE.
- rename VXLAN_GPE_TYPE_IPV4 as RTE_VXLAN_GPE_TYPE_IPV4.
- rename VXLAN_GPE_TYPE_IPV6 as RTE_VXLAN_GPE_TYPE_IPV6.
- rename VXLAN_GPE_TYPE_ETH as RTE_VXLAN_GPE_TYPE_ETH.
- rename VXLAN_GPE_TYPE_NSH as RTE_VXLAN_GPE_TYPE_NSH.
- rename VXLAN_GPE_TYPE_MPLS as RTE_VXLAN_GPE_TYPE_MPLS.
- rename VXLAN_GPE_TYPE_GBP as RTE_VXLAN_GPE_TYPE_GBP.
- rename VXLAN_GPE_TYPE_VBNG as RTE_VXLAN_GPE_TYPE_VBNG.
- rename ETHER_VXLAN_GPE_HLEN as RTE_ETHER_VXLAN_GPE_HLEN.
Do not update the command line library to avoid adding a dependency to
librte_net.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
This patch introduces:
- VMxnet3 v4 negotiation and,
- entirely guest-driven UDP RSS support.
VMxnet3 v3 already has UDP RSS support, however it
depends on hypervisor provisioning on the VM through
ESX specific flags, which are not transparent or known
to the guest later on.
Vmxnet3 v4 introduces a new API transaction which allows
configuring RSS entirely from the guest. This API must be
invoked after device shared mem region is initialized.
IPv4 ESP RSS (SPI based) is also available, but currently
there are no ESP RSS definitions on rte_eth layer to
handle that.
Signed-off-by: Eduard Serra <eserra@vmware.com>
Acked-by: Yong Wang <yongwang@vmware.com>
'stats_reset()' callback was missing because the device backend doesn't
support it.
This commit adds a workaround to this and implements the callback by
taking a snapshot of the stats (SNAPSHOT) each time 'stats_reset()'
is called. When getting stats with 'stats_get()', hw stats which
always increase reduce SNAPSHOT stats.
That's how we get the "real" stats since the last 'stats_reset()'.
Signed-off-by: Yogev Chaimovich <yogev@cgstowernetworks.com>
Acked-by: Yong Wang <yongwang@vmware.com>
Not so old variants of vmxnet3 do not provide MSS value along with
LRO packet. When this case happens, try to guess MSS value with
information at hand.
Signed-off-by: Didier Pallard <didier.pallard@6wind.com>
Acked-by: Yong Wang <yongwang@vmware.com>
Replace the BSD license header with the SPDX tag for files
with only an Intel copyright on them.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Generate link-state change notifications by listening to interrupts
generated by the device. Make use of the existing
vmxnet3_process_events function that was compiled out, but change it
to call vmxnet3_dev_link_update on a VMXNET3_ECR_LINK event and to not
be so noisy in its log messages.
Enable interrupts on starting the device, using a new helper function,
vmxnet3_enable_intr, based on vmxnet3_disable_intr and validated
against the FreeBSD driver.
Keep track of the number of interrupts registered for to avoid
hardcoding these in vmxnet3_enable/disable_intr and to provision for
any future rxq intr support.
Factor out the guts of vmxnet3_dev_link_update minus the started check
to allow the new function to be called from vmxnet3_dev_start in the
lsc-enabled case to ensure that the link state is correctly set from
the actual state at that point.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Most NICs like virtio, igb/ixgbe etc. don't reset counters on
dev_start and arguably this helps in monitoring the counters
across a longer time span with multiple device start/stops.
vmxnet3 behavior is opposite to that and counters are reset by
the host side implementation each time the device is restarted.
Change the driver to save the counters in its private context
before it is reset by writing CMD_ACTIVATE to REG_CMD.
Signed-off-by: Nachiketa Prachanda <nprachan@brocade.com>
Acked-by: Shrikrishna Khare <skhare@vmware.com>
In vmxnet3 version 3, the emulation added support for the vmxnet3 driver
to communicate information about the memory regions the driver will use
for rx/tx buffers. The driver can also indicate which rx/tx queue the
memory region is applicable for. If this information is communicated
to the emulation, the emulation will always keep these memory regions
mapped, thereby avoiding the mapping/unmapping overhead for every packet.
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: Guolin Yang <gyang@vmware.com>
Acked-by: Yong Wang <yongwang@vmware.com>
Acked-by: Jin Heo <heoj@vmware.com>
vmxnet3 driver preallocates buffers for receiving packets and posts the
buffers to the emulation. In order to deliver a received packet to the
guest, the emulation must map buffer(s) and copy the packet into it.
To avoid this memory mapping overhead, this patch introduces the receive
data ring - a set of small sized buffers that are always mapped by
the emulation. If a packet fits into the receive data ring buffer, the
emulation delivers the packet via the receive data ring (which must be
copied by the guest driver), or else the usual receive path is used.
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Acked-by: Yong Wang <yongwang@vmware.com>
Acked-by: Jin Heo <heoj@vmware.com>
vmxnet3 driver supports transmit data ring viz. a set of fixed size
buffers used by the driver to copy packet headers. Small packets that
fit these buffers are copied into these buffers entirely.
Currently this buffer size of fixed at 128 bytes. This patch extends
transmit data ring implementation to allow variable length transmit
data ring buffers. The length of the buffer is read from the emulation
during initialization.
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Acked-by: Yong Wang <yongwang@vmware.com>
Acked-by: Jin Heo <heoj@vmware.com>
Cleanup some code in preparation of vmxnet3 version 3 changes.
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Acked-by: Yong Wang <yongwang@vmware.com>
Acked-by: Jin Heo <heoj@vmware.com>
Replace the raw I/O device memory read/write access with eal
abstraction for I/O device memory read/write access to fix
portability issues across different architectures.
CC: Yong Wang <yongwang@vmware.com>
Signed-off-by: Santosh Shukla <santosh.shukla@caviumnetworks.com>
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
The macro RTE_VERIFY always checks a condition.
It is optimized with "unlikely" hint.
While this macro is well suited for test applications, it is preferred
in libraries and examples to enable such check in debug mode.
That's why the macro RTE_ASSERT is introduced to call RTE_VERIFY only
if built with debug logs enabled.
A lot of assert macros were duplicated and enabled with a specific flag.
Removing these #ifdef allows to test these code branches more easily
and avoid dead code pitfalls.
The ENA_ASSERT is kept (in debug mode only) because it has more
parameters to log.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
By defining macro as a stub it is possible to get rid of #ifdef's
in the actual code. Always evaluate the argument (even in the stub)
so that there are no extra unused variable errors.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Yong Wang <yongwang@vmware.com>
Remove check for packets greater than MTU. No other driver does
this, it should be handled at higher layer
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Yong Wang <yongwang@vmware.com>
Support the VLAN filter functionality of the VMXNET3 interface.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Yong Wang <yongwang@vmware.com>
Move vmxnet3 PMD to drivers/net directory.
As part of the move, rename the "vmxnet3" subdirectory, containing the
original FreeBSD drivers, from "vmxnet3" to the more standard name
"base", to indicate it contains the base drivers used for the
implementation.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
